pm24.git/drivers/net/ethernet/intel/ice/devlink, branch master

ice: block SF port creation in legacy mode

2024-10-29T14:24:53Z

There is no support for SF in legacy mode. Reflect it in the code. Reviewed-by: Przemek Kitszel Fixes: eda69d654c7e ("ice: add basic devlink subfunctions support") Signed-off-by: Michal Swiatkowski Reviewed-by: Kalesh AP Tested-by: Rafal Romanowski Signed-off-by: Jacob Keller Reviewed-by: Simon Horman Signed-off-by: Paolo Abeni

ice: subfunction activation and base devlink ops

2024-09-06T18:01:24Z

Use previously implemented SF aux driver. It is probe during SF activation and remove after deactivation. Implement set/get hw_address and set/get state as basic devlink ops for subfunction. Reviewed-by: Simon Horman Signed-off-by: Piotr Raczynski Signed-off-by: Michal Swiatkowski Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen

ice: support subfunction devlink Tx topology

2024-09-06T18:01:24Z

Flow for creating Tx topology is the same as for VF port representors, but the devlink port is stored in different place (sf->devlink_port). When creating VF devlink lock isn't taken, when creating subfunction it is. Setting Tx topology function needs to take this lock, check if it was taken before to not do it twice. Reviewed-by: Simon Horman Reviewed-by: Przemek Kitszel Reviewed-by: Wojciech Drewek Signed-off-by: Michal Swiatkowski Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen

ice: create port representor for SF

2024-09-06T18:01:24Z

Implement attaching and detaching SF port representor. It is done in the same way as the VF port representor. SF port representor is always added or removed with devlink lock taken. Reviewed-by: Simon Horman Signed-off-by: Michal Swiatkowski Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen

ice: make representor code generic

2024-09-06T18:01:24Z

Keep the same flow of port representor creation, but instead of general attach function create helpers for specific representor type. Store function pointer for add and remove representor. Type of port representor can be also known based on VSI type, but it is more clean to have it directly saved in port representor structure. Add devlink lock for whole port representor creation and destruction. Reviewed-by: Simon Horman Reviewed-by: Wojciech Drewek Signed-off-by: Michal Swiatkowski Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen

ice: base subfunction aux driver

2024-09-06T18:01:24Z

Implement subfunction driver. It is probe when subfunction port is activated. VSI is already created. During the probe VSI is being configured. MAC unicast and broadcast filter is added to allow traffic to pass. Store subfunction pointer in VSI struct. The same is done for VF pointer. Make union of subfunction and VF pointer as only one of them can be set with one VSI. Reviewed-by: Simon Horman Reviewed-by: Jiri Pirko Signed-off-by: Piotr Raczynski Signed-off-by: Michal Swiatkowski Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen

ice: allocate devlink for subfunction

2024-09-06T18:01:24Z

Allocate devlink for subfunction instance. Create header file for subfunction device. Define subfunction device structure there as it is needed for devlink allocation. Reviewed-by: Przemek Kitszel Reviewed-by: Jiri Pirko Signed-off-by: Piotr Raczynski Signed-off-by: Michal Swiatkowski Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen

ice: add basic devlink subfunctions support

2024-09-06T18:01:23Z

Implement devlink port handlers responsible for ethernet type devlink subfunctions. Create subfunction devlink port and setup all resources needed for a subfunction netdev to operate. Configure new VSI for each new subfunction, initialize and configure interrupts and Tx/Rx resources. Set correct MAC filters and create new netdev. For now, subfunction is limited to only one Tx/Rx queue pair. Only allocate new subfunction VSI with devlink port new command. Allocate and free subfunction MSIX interrupt vectors using new API calls with pci_msix_alloc_irq_at and pci_msix_free_irq. Support both automatic and manual subfunction numbers. If no subfunction number is provided, use xa_alloc to pick a number automatically. This will find the first free index and use that as the number. This reduces burden on users in the simple case where a specific number is not required. It may also be slightly faster to check that a number exists since xarray lookup should be faster than a linear scan of the dyn_ports xarray. Co-developed-by: Jacob Keller Signed-off-by: Jacob Keller Signed-off-by: Piotr Raczynski Signed-off-by: Michal Swiatkowski Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen

ice: use internal pf id instead of function number

2024-08-20T20:23:01Z

Use always the same pf id in devlink port number. When doing pass-through the PF to VM bus info func number can be any value. Fixes: 2ae0aa4758b0 ("ice: Move devlink port to PF/VF struct") Reviewed-by: Wojciech Drewek Suggested-by: Jiri Pirko Signed-off-by: Michal Swiatkowski Signed-off-by: Tony Nguyen

ice: Add support for devlink local_forwarding param

2024-07-11T17:53:57Z

Add support for driver-specific devlink local_forwarding param. Supported values are "enabled", "disabled" and "prioritized". Default configuration is set to "enabled". Add documentation in networking/devlink/ice.rst. In previous generations of Intel NICs the transmit scheduler was only limited by PCIe bandwidth when scheduling/assigning hairpin-bandwidth between VFs. Changes to E810 HW design introduced scheduler limitation, so that available hairpin-bandwidth is bound to external port speed. In order to address this limitation and enable NFV services such as "service chaining" a knob to adjust the scheduler config was created. Driver can send a configuration message to the FW over admin queue and internal FW logic will reconfigure HW to prioritize and add more BW to VF to VF traffic. An end result, for example, 10G port will no longer limit hairpin-bandwidth to 10G and much higher speeds can be achieved. Devlink local_forwarding param set to "prioritized" enables higher hairpin-bandwitdh on related PFs. Configuration is applicable only to 8x10G and 4x25G cards. Changing local_forwarding configuration will trigger CORER reset in order to take effect. Example command to change current value: devlink dev param set pci/0000:b2:00.3 name local_forwarding \ value prioritized \ cmode runtime Co-developed-by: Michal Wilczynski Signed-off-by: Michal Wilczynski Reviewed-by: Przemek Kitszel Signed-off-by: Pawel Kaminski Signed-off-by: Wojciech Drewek Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen