pm24.git/drivers/net/phy, branch cpufreq-rust

net: phy: c45-tjaxx: add delay between MDIO write and read in soft_reset

2025-01-27T23:02:51Z

In application note (AN13663) for TJA1120, on page 30, there's a figure with average PHY startup timing values following software reset. The time it takes for SMI to become operational after software reset ranges roughly from 500 us to 1500 us. This commit adds 2000 us delay after MDIO write which triggers software reset. Without this delay, soft_reset function returns an error and prevents successful PHY init. Cc: stable@vger.kernel.org Fixes: b050f2f15e04 ("phy: nxp-c45: add driver for tja1103") Signed-off-by: Milos Reljin Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/AM8P250MB0124D258E5A71041AF2CC322E1E32@AM8P250MB0124.EURP250.PROD.OUTLOOK.COM Signed-off-by: Jakub Kicinski

net: phy: marvell-88q2xxx: Fix temperature measurement with reset-gpios

2025-01-23T08:55:06Z

When using temperature measurement on Marvell 88Q2XXX devices and the reset-gpios property is set in DT, the device does a hardware reset when interface is brought down and up again. That means that the content of the register MDIO_MMD_PCS_MV_TEMP_SENSOR2 is reset to default and that leads to permanent deactivation of the temperature measurement, because activation is done in mv88q2xxx_probe. To fix this move activation of temperature measurement to mv88q222x_config_init. Fixes: a557a92e6881 ("net: phy: marvell-88q2xxx: add support for temperature sensor") Reviewed-by: Niklas Söderlund Signed-off-by: Dimitri Fedrau Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20250118-marvell-88q2xxx-fix-hwmon-v2-1-402e62ba2dcb@gmail.com Signed-off-by: Paolo Abeni

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2025-01-21T09:24:33Z

No conflicts and no adjacent changes. Signed-off-by: Paolo Abeni

net: phylink: fix regression when binding a PHY

2025-01-21T00:32:42Z

Some PHYs don't support clause 45 access, and return -EOPNOTSUPP from phy_modify_mmd(), which causes phylink_bringup_phy() to fail. Prevent this failure by allowing -EOPNOTSUPP to also mean success. Reported-by: Jiawen Wu Tested-by: Jiawen Wu Signed-off-by: Russell King (Oracle) Reviewed-by: Simon Horman Link: https://patch.msgid.link/E1tZp1a-001V62-DT@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski

net: phy: realtek: HWMON support for standalone versions of RTL8221B and RTL8251

2025-01-20T12:30:56Z

HWMON support has been added for the RTL8221/8251 PHYs integrated together with the MAC inside the RTL8125/8126 chips. This patch extends temperature reading support for standalone variants of the mentioned PHYs. I don't know whether the earlier revisions of the RTL8226 also have a built-in temperature sensor, so they have been skipped for now. Tested on RTL8221B-VB-CG. Signed-off-by: Aleksander Jan Bajkowski Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: phylink: always do a major config when attaching a SFP PHY

2025-01-20T12:17:35Z

Background: https://lore.kernel.org/r/20250107123615.161095-1-ericwouds@gmail.com Since adding negotiation of in-band capabilities, it is no longer sufficient to just look at the MLO_AN_xxx mode and PHY interface to decide whether to do a major configuration, since the result now depends on the capabilities of the attaching PHY. Always trigger a major configuration in this case. Testing log: https://lore.kernel.org/r/f20c9744-3953-40e7-a9c9-5534b25d2e2a@gmail.com Reported-by: Eric Woudstra Tested-by: Eric Woudstra Signed-off-by: Russell King (Oracle) Signed-off-by: David S. Miller

net: phy: remove leftovers from switch to linkmode bitmaps

2025-01-19T01:40:10Z

We have some leftovers from the switch to linkmode bitmaps which - have never been used - are not used any longer - have no user outside phy_device.c So remove them. Signed-off-by: Heiner Kallweit Link: https://patch.msgid.link/5493b96e-88bb-4230-a911-322659ec5167@gmail.com Signed-off-by: Jakub Kicinski

net: phy: realtek: always clear NBase-T lpa

2025-01-17T12:01:40Z

Clear NBase-T link partner advertisement before calling rtlgen_read_status() to avoid phy_resolve_aneg_linkmode() wrongly setting speed and duplex. This fixes bogus 2.5G/5G/10G link partner advertisement and thus speed and duplex being set by phy_resolve_aneg_linkmode() due to stale NBase-T lpa. Fixes: 68d5cd09e891 ("net: phy: realtek: change order of calls in C22 read_status()") Signed-off-by: Daniel Golle Reviewed-by: Michal Swiatkowski Signed-off-by: David S. Miller

net: phy: realtek: clear master_slave_state if link is down

2025-01-17T12:01:40Z

rtlgen_decode_physr() which sets master_slave_state isn't called in case the link is down and other than rtlgen_read_status(), rtl822x_c45_read_status() doesn't implicitely clear master_slave_state. Avoid stale master_slave_state by always setting it to MASTER_SLAVE_STATE_UNKNOWN in rtl822x_c45_read_status() in case the link is down. Fixes: 081c9c0265c9 ("net: phy: realtek: read duplex and gbit master from PHYSR register") Signed-off-by: Daniel Golle Reviewed-by: Michal Swiatkowski Signed-off-by: David S. Miller

net: phy: realtek: clear 1000Base-T lpa if link is down

2025-01-17T12:01:40Z

Only read 1000Base-T link partner advertisement if autonegotiation has completed and otherwise 1000Base-T link partner advertisement bits. This fixes bogus 1000Base-T link partner advertisement after link goes down (eg. by disconnecting the wire). Fixes: 5cb409b3960e ("net: phy: realtek: clear 1000Base-T link partner advertisement") Signed-off-by: Daniel Golle Reviewed-by: Michal Swiatkowski Signed-off-by: David S. Miller