pm24.git/include/linux/mtd, branch v4.18-rc2

Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd

2018-06-08T17:39:20Z

Pull MTD updates from Boris Brezillon: "Core changes: - Add a sysfs attribute to expose available OOB size Driver changes: - Remove HAS_DMA dependency on various drivers - Use dev_get_drvdata() instead of platform_get_drvdata() in docg3 - Replace msleep by usleep_range() in the dataflash driver - Avoid VLA usage in nftl layers - Remove useless .owner assignment in pismo - Fix various issues in the CFI driver - Improve TRX partition handling expose a DT compat for this part parser - Clarify OFFSET_CONTINUOUS meaning NAND core changes: - Add Miquel as a NAND maintainer - Add access mode to the nand_page_io_req struct - Fix kernel-doc in rawnand.h - Support bit-wise majority to recover from corrupted ONFI parameter pages - Stop checking FAIL bit after a SET_FEATURES, as documented in the ONFI spec Raw NAND Driver changes: - Fix and cleanup the error path of many NAND controller drivers - GPMI: + Cleanup/simplification of a few aspects in the driver + Take ECC setup specified in the DT into account - sunxi: remove support for GPIO-based R/B polling - MTK: + Use of_device_get_match_data() instead of of_match_device() + Add an entry in MAINTAINERS for this driver + Fix nand-ecc-step-size and nand-ecc-strength description in the DT bindings doc - fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page OneNAND driver changes: - samsung: use dev_get_drvdata() instead of platform_get_drvdata() SPI NOR core changes: - Add support for a bunch of SPI NOR chips - Clear EAR reg when switching to 3-byte addressing mode on Winbond chips SPI NOR controller driver changes: - cadence: Add DMA support for direct mode reads - hisi: Prefix a few functions with hisi_ - intel: + Mark the driver as "dangerous" in Kconfig + Fix atomic sequence handling + Pass a 40us delay (instead of 0us) to readl_poll_timeout() - fsl: + fix a typo in a function name + add support for IP variants embedded in the ls2080a and ls1080a SoCs - stm32: request exclusive control of the reset line" * tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits) mtd: nand: Pass mode information to nand_page_io_req mtd: cfi_cmdset_0002: Change erase one block to enable XIP once mtd: cfi_cmdset_0002: Change erase functions to check chip good only mtd: cfi_cmdset_0002: Change erase functions to retry for error mtd: cfi_cmdset_0002: Change definition naming to retry write operation mtd: cfi_cmdset_0002: Change write buffer to check correct value mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS mtd: bcm47xxpart: add of_match_table with a new DT binding dt-bindings: mtd: document Broadcom's BCM47xx partitions mtd: spi-nor: Add support for EN25QH32 mtd: spi-nor: Add support for is25wp series chips mtd: spi-nor: Add Winbond w25q32jv support mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control mtd: spi-nor: intel: provide a range for poll_timout mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig mtd: spi-nor: intel-spi: Fix atomic sequence handling mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op mtd: rawnand: use bit-wise majority to recover the ONFI param page ...

Merge tag 'spi-nor/for-4.18' of git://git.infradead.org/linux-mtd into mtd/next

2018-06-07T20:53:15Z

Core changes: - Add support for a bunch of SPI NOR chips - Clear EAR reg when switching to 3-byte addressing mode on Winbond chips SPI NOR controller driver changes: - cadence: Add DMA support for direct mode reads - hisi: Prefix a few functions with hisi_ - intel: * Mark the driver as "dangerous" in Kconfig * Fix atomic sequence handling * Pass a 40us delay (instead of 0us) to readl_poll_timeout() - fsl: * fix a typo in a function name * add support for IP variants embedded in the ls2080a and ls1080a SoCs - stm32: request exclusive control of the reset line

mtd: nand: Pass mode information to nand_page_io_req

2018-06-01T12:53:50Z

The NAND sub-layers are likely to need the MTD_OPS_XXX mode information in order to decide if they should enable/disable ECC or how they should place the OOB bytes in the provided OOB buffer. Add a field to nand_page_io_req to pass this information. Signed-off-by: Boris Brezillon Reviewed-by: Miquel Raynal Tested-by: Frieder Schrempf Reviewed-by: Frieder Schrempf

mtd: rawnand: Fix return type of __DIVIDE() when called with 32-bit

2018-05-15T12:40:34Z

The __DIVIDE() macro checks whether it is called with a 32-bit or 64-bit dividend, to select the appropriate divide-and-round-up routine. As the check uses the ternary operator, the result will always be promoted to a type that can hold both results, i.e. unsigned long long. When using this result in a division on a 32-bit system, this may lead to link errors like: ERROR: "__udivdi3" [drivers/mtd/nand/raw/nand.ko] undefined! Fix this by casting the result of the division to the type of the dividend. Fixes: 8878b126df769831 ("mtd: nand: add ->exec_op() implementation") Signed-off-by: Geert Uytterhoeven Signed-off-by: Boris Brezillon

mtd: Fix comparison in map_word_andequal()

2018-05-14T12:46:20Z

Commit 9e343e87d2c4 ("mtd: cfi: convert inline functions to macros") changed map_word_andequal() into a macro, but also changed the right hand side of the comparison from val3 to val2. Change it back to use val3 on the right hand side. Thankfully this did not cause a regression because all callers currently pass the same argument for val2 and val3. Fixes: 9e343e87d2c4 ("mtd: cfi: convert inline functions to macros") Signed-off-by: Ben Hutchings Signed-off-by: Boris Brezillon

mtd: rawnand.h: use nested union kernel-doc markups

2018-05-09T14:23:12Z

Gets rid of those warnings and better document the parameters. ./include/linux/mtd/rawnand.h:752: warning: Function parameter or member 'timings.sdr' not described in 'nand_data_interface' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.in' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.out' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.cmd' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.data' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.waitrdy' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.data' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.desc' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.priv' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:848: WARNING: Unexpected indentation. Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Boris Brezillon

mtd: rawnand: add a way to pass an ID table with nand_scan()

2018-04-29T06:56:46Z

As part of the work of migrating all the drivers to nand_scan(), and because nand_scan() does not provide a way to pass an ID table, rename the function nand_scan_with_ids() and add a third parameter to give a flash ID table (like what was done with nand_scan_ident()). Create a nand_scan() helper that is just a wrapper of nand_scan_with_ids(), passing NULL as the ID table. This way a controller drivers can continue using nand_scan() transparently. Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon

mtd: cfi: cmdset_0001: Do not allow read/write to suspend erase block.

2018-04-24T15:41:18Z

Currently it is possible to read and/or write to suspend EB's. Writing /dev/mtdX or /dev/mtdblockX from several processes may break the flash state machine. Signed-off-by: Joakim Tjernlund Cc: Reviewed-by: Richard Weinberger Signed-off-by: Boris Brezillon

mtd: spi-nor: clear Winbond Extended Address Reg on switch to 3-byte addressing.

2018-04-21T08:05:23Z

Winbond spi-nor flash 32MB and larger have an 'Extended Address Register' as one option for addressing beyond 16MB (Macronix has the same concept, Spansion has EXTADD bits in the Bank Address Register). According to section 8.2.7 Write Extended Address Register (C5h) of the Winbond W25Q256FV data sheet (256M-BIT SPI flash) The Extended Address Register is only effective when the device is in the 3-Byte Address Mode. When the device operates in the 4-Byte Address Mode (ADS=1), any command with address input of A31-A24 will replace the Extended Address Register values. It is recommended to check and update the Extended Address Register if necessary when the device is switched from 4-Byte to 3-Byte Address Mode. So the documentation suggests clearing the EAR after switching to 3-byte mode. Experimentation shows that the EAR is *always* one after the switch to 3-byte mode, so clearing the EAR is mandatory at shutdown for a subsequent 3-byte-addressed reboot to work. Note that some SOCs (e.g. MT7621) do not assert a reset line at normal reboot, so we cannot rely on hardware reset. The MT7621 does assert a reset line at watchdog-reset. Acked-by: Marek Vasut Signed-off-by: NeilBrown Signed-off-by: Boris Brezillon

Merge tag 'nand/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next

2018-04-04T20:11:36Z

Core changes: * Prepare arrival of the SPI NAND subsystem by implementing a generic (interface-agnostic) layer to ease manipulation of NAND devices * Move onenand code base to the drivers/mtd/nand/ dir * Rework timing mode selection * Provide a generic way for NAND chip drivers to flag a specific GET/SET FEATURE operation as supported/unsupported * Stop embedding ONFI/JEDEC param page in nand_chip Driver changes: * Rework/cleanup of the mxc driver * Various cleanups in the vf610 driver * Migrate the fsmc and vf610 to ->exec_op() * Get rid of the pxa driver (replaced by marvell_nand) * Support ->setup_data_interface() in the GPMI driver * Fix probe error path in several drivers * Remove support for unused hw_syndrome mode in sunxi_nand * Various minor improvements