pm24.git/include/uapi/linux/ethtool_netlink.h, branch v5.8-rc5

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

2020-06-03T23:27:18Z

Pull networking updates from David Miller: 1) Allow setting bluetooth L2CAP modes via socket option, from Luiz Augusto von Dentz. 2) Add GSO partial support to igc, from Sasha Neftin. 3) Several cleanups and improvements to r8169 from Heiner Kallweit. 4) Add IF_OPER_TESTING link state and use it when ethtool triggers a device self-test. From Andrew Lunn. 5) Start moving away from custom driver versions, use the globally defined kernel version instead, from Leon Romanovsky. 6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin. 7) Allow hard IRQ deferral during NAPI, from Eric Dumazet. 8) Add sriov and vf support to hinic, from Luo bin. 9) Support Media Redundancy Protocol (MRP) in the bridging code, from Horatiu Vultur. 10) Support netmap in the nft_nat code, from Pablo Neira Ayuso. 11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina Dubroca. Also add ipv6 support for espintcp. 12) Lots of ReST conversions of the networking documentation, from Mauro Carvalho Chehab. 13) Support configuration of ethtool rxnfc flows in bcmgenet driver, from Doug Berger. 14) Allow to dump cgroup id and filter by it in inet_diag code, from Dmitry Yakunin. 15) Add infrastructure to export netlink attribute policies to userspace, from Johannes Berg. 16) Several optimizations to sch_fq scheduler, from Eric Dumazet. 17) Fallback to the default qdisc if qdisc init fails because otherwise a packet scheduler init failure will make a device inoperative. From Jesper Dangaard Brouer. 18) Several RISCV bpf jit optimizations, from Luke Nelson. 19) Correct the return type of the ->ndo_start_xmit() method in several drivers, it's netdev_tx_t but many drivers were using 'int'. From Yunjian Wang. 20) Add an ethtool interface for PHY master/slave config, from Oleksij Rempel. 21) Add BPF iterators, from Yonghang Song. 22) Add cable test infrastructure, including ethool interfaces, from Andrew Lunn. Marvell PHY driver is the first to support this facility. 23) Remove zero-length arrays all over, from Gustavo A. R. Silva. 24) Calculate and maintain an explicit frame size in XDP, from Jesper Dangaard Brouer. 25) Add CAP_BPF, from Alexei Starovoitov. 26) Support terse dumps in the packet scheduler, from Vlad Buslov. 27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei. 28) Add devm_register_netdev(), from Bartosz Golaszewski. 29) Minimize qdisc resets, from Cong Wang. 30) Get rid of kernel_getsockopt and kernel_setsockopt in order to eliminate set_fs/get_fs calls. From Christoph Hellwig. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits) selftests: net: ip_defrag: ignore EPERM net_failover: fixed rollback in net_failover_open() Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv" Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv" vmxnet3: allow rx flow hash ops only when rss is enabled hinic: add set_channels ethtool_ops support selftests/bpf: Add a default $(CXX) value tools/bpf: Don't use $(COMPILE.c) bpf, selftests: Use bpf_probe_read_kernel s390/bpf: Use bcr 0,%0 as tail call nop filler s390/bpf: Maintain 8-byte stack alignment selftests/bpf: Fix verifier test selftests/bpf: Fix sample_cnt shared between two threads bpf, selftests: Adapt cls_redirect to call csum_level helper bpf: Add csum_level helper for fixing up csum levels bpf: Fix up bpf_skb_adjust_room helper's skb csum setting sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf() crypto/chtls: IPv6 support for inline TLS Crypto/chcr: Fixes a coccinile check error Crypto/chcr: Fixes compilations warnings ...

net: ethtool: Allow PHY cable test TDR data to configured

2020-05-27T06:22:21Z

Allow the user to configure where on the cable the TDR data should be retrieved, in terms of first and last sample, and the step between samples. Also add the ability to ask for TDR data for just one pair. If this configuration is not provided, it defaults to 1-150m at 1m intervals for all pairs. Signed-off-by: Andrew Lunn v3: Move the TDR configuration into a structure Add a range check on step Use NL_SET_ERR_MSG_ATTR() when appropriate Move TDR configuration into a nest Document attributes in the request Signed-off-by: David S. Miller

net: ethtool: Add attributes for cable test TDR data

2020-05-27T06:21:48Z

Some Ethernet PHYs can return the raw time domain reflectromatry data. Add the attributes to allow this data to be requested and returned via netlink ethtool. Signed-off-by: Andrew Lunn v2: m -> cm Report what the PHY actually used for start/stop/step. Signed-off-by: David S. Miller

ethtool: provide UAPI for PHY Signal Quality Index (SQI)

2020-05-22T00:18:00Z

Signal Quality Index is a mandatory value required by "OPEN Alliance SIG" for the 100Base-T1 PHYs [1]. This indicator can be used for cable integrity diagnostic and investigating other noise sources and implement by at least two vendors: NXP[2] and TI[3]. [1] http://www.opensig.org/download/document/218/Advanced_PHY_features_for_automotive_Ethernet_V1.0.pdf [2] https://www.nxp.com/docs/en/data-sheet/TJA1100.pdf [3] https://www.ti.com/product/DP83TC811R-Q1 Signed-off-by: Oleksij Rempel Reviewed-by: Andrew Lunn Reviewed-by: Michal Kubecek Signed-off-by: David S. Miller

net: ethtool: Add attributes for cable test reports

2020-05-10T19:28:41Z

Add the attributes needed to report cable test results to userspace. The reports are expected to be per twisted pair. A nested property per pair can report the result of the cable test. A nested property can also report the length of the cable to any fault. v2: Grammar fixes Change length from u16 to u32 s/DEV/HEADER/g Add status attributes Rename pairs from numbers to letters. v3: Fixed example in document Add ETHTOOL_A_CABLE_NEST_* enum Add ETHTOOL_MSG_CABLE_TEST_NTF to documentation Signed-off-by: Andrew Lunn Reviewed-by: Florian Fainelli Reviewed-by: Michal Kubecek Signed-off-by: Jakub Kicinski

net: ethtool: netlink: Add support for triggering a cable test

2020-05-10T19:28:41Z

Add new ethtool netlink calls to trigger the starting of a PHY cable test. Add Kconfig'ury to ETHTOOL_NETLINK so that PHYLIB is not a module when ETHTOOL_NETLINK is builtin, which would result in kernel linking errors. v2: Remove unwanted white space change Remove ethnl_cable_test_act_ops and use doit handler Rename cable_test_set_policy cable_test_act_policy Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY v3: Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY from documentation Remove unused cable_test_get_policy Add Reviewed-by tags v4: Remove unwanted blank line Signed-off-by: Andrew Lunn Reviewed-by: Michal Kubecek Reviewed-by: Florian Fainelli Signed-off-by: Jakub Kicinski

ethtool: provide UAPI for PHY master/slave configuration.

2020-05-07T00:45:45Z

This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of auto-negotiation support, we needed to be able to configure the MASTER-SLAVE role of the port manually or from an application in user space. The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to force MASTER or SLAVE role. See IEEE 802.3-2018: 22.2.4.3.7 MASTER-SLAVE control register (Register 9) 22.2.4.3.8 MASTER-SLAVE status register (Register 10) 40.5.2 MASTER-SLAVE configuration resolution 45.2.1.185.1 MASTER-SLAVE config value (1.2100.14) 45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32) The MASTER-SLAVE role affects the clock configuration: ------------------------------------------------------------------------------- When the PHY is configured as MASTER, the PMA Transmit function shall source TX_TCLK from a local clock source. When configured as SLAVE, the PMA Transmit function shall source TX_TCLK from the clock recovered from data stream provided by MASTER. iMX6Q KSZ9031 XXX ------\ /-----------\ /------------\ | | | | | MAC |<----RGMII----->| PHY Slave |<------>| PHY Master | |<--- 125 MHz ---+-<------/ | | \ | ------/ \-----------/ \------------/ ^ \-TX_TCLK ------------------------------------------------------------------------------- Since some clock or link related issues are only reproducible in a specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial to provide generic (not 100BASE-T1 specific) interface to the user space for configuration flexibility and trouble shooting. Signed-off-by: Oleksij Rempel Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

docs: fix broken references to text files

2020-04-20T21:35:59Z

Several references got broken due to txt to ReST conversion. Several of them can be automatically fixed with: scripts/documentation-file-ref-check --fix Reviewed-by: Mathieu Poirier # hwtracing/coresight/Kconfig Reviewed-by: Paul E. McKenney # memory-barrier.txt Acked-by: Alex Shi # translations/zh_CN Acked-by: Federico Vaga # translations/it_IT Acked-by: Marc Zyngier # kvm/arm64 Signed-off-by: Mauro Carvalho Chehab Link: https://lore.kernel.org/r/6f919ddb83a33b5f2a63b6b5f0575737bb2b36aa.1586881715.git.mchehab+huawei@kernel.org Signed-off-by: Jonathan Corbet

ethtool: provide timestamping information with TSINFO_GET request

2020-03-30T05:32:37Z

Implement TSINFO_GET request to get timestamping information for a network device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl request. Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink code use the same logic to get timestamping information from the device. v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran Signed-off-by: Michal Kubecek Acked-by: Richard Cochran Signed-off-by: David S. Miller

ethtool: add EEE_NTF notification

2020-03-30T05:32:36Z

Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network device are modified using ETHTOOL_MSG_EEE_SET netlink message or ETHTOOL_SEEE ioctl request. Signed-off-by: Michal Kubecek Signed-off-by: David S. Miller