Merge tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC driver updates from Arnd Bergmann:
 "Nothing particular important in the SoC driver updates, just the usual
  improvements to for drivers/soc and a couple of subsystems that don't
  fit anywhere else:

   - The largest set of updates is for Qualcomm SoC drivers, extending
     the set of supported features for additional SoCs in the QSEECOM,
     LLCC and socinfo drivers.a

   - The ti_sci firmware driver gains support for power managment

   - The drivers/reset subsystem sees a rework of the microchip sparx5
     and amlogic reset drivers to support additional chips, plus a few
     minor updates on other platforms

   - The SCMI firmware interface driver gains support for two protocol
     extensions, allowing more flexible use of the shared memory area
     and new DT binding properties for configurability.

   - Mediatek SoC drivers gain support for power managment on the MT8188
     SoC and a new driver for DVFS.

   - The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
     and a few bugfixes

   - The Hisilicon Kunpeng HCCS driver gains support for configuring
     lanes through sysfs

  Finally, there are cleanups and minor fixes for drivers/{soc, bus,
  memory}, including changing back the .remove_new callback to .remove,
  as well as a few other updates for freescale (powerpc) soc drivers,
  NXP i.MX soc drivers, cznic turris platform driver, memory controller
  drviers, TI OMAP SoC drivers, and Tegra firmware drivers"

* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
  soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
  soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
  soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
  platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
  platform: cznic: turris-omnia-mcu: Document the driver private data structure
  firmware: turris-mox-rwtm: Document the driver private data structure
  bus: Switch back to struct platform_driver::remove()
  soc: qcom: ice: Remove the device_link field in qcom_ice
  drm/msm/adreno: Setup SMMU aparture for per-process page table
  firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
  firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
  soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
  dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
  soc: qcom: llcc: Flip the manual slice configuration condition
  dt-bindings: firmware: qcom,scm: Document sm8750 SCM
  firmware: qcom: uefisecapp: Allow X1E Devkit devices
  misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
  misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
  soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
  dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
  ...

4 files changed, 419 insertions, 0 deletions

diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 3fe7e2a9bd29..902c306bc972 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -610,6 +610,30 @@ config MARVELL_CN10K_DPI
 	  To compile this driver as a module, choose M here: the module
 	  will be called mrvl_cn10k_dpi.
 
+config MCHP_LAN966X_PCI
+	tristate "Microchip LAN966x PCIe Support"
+	depends on PCI
+	select OF
+	select OF_OVERLAY
+	select IRQ_DOMAIN
+	help
+	  This enables the support for the LAN966x PCIe device.
+
+	  This is used to drive the LAN966x PCIe device from the host system
+	  to which it is connected. The driver uses a device tree overlay to
+	  load other drivers to support for LAN966x internal components.
+
+	  Even if this driver does not depend on those other drivers, in order
+	  to have a fully functional board, the following drivers are needed:
+	    - fixed-clock (COMMON_CLK)
+	    - lan966x-oic (LAN966X_OIC)
+	    - lan966x-cpu-syscon (MFD_SYSCON)
+	    - lan966x-switch-reset (RESET_MCHP_SPARX5)
+	    - lan966x-pinctrl (PINCTRL_OCELOT)
+	    - lan966x-serdes (PHY_LAN966X_SERDES)
+	    - lan966x-miim (MDIO_MSCC_MIIM)
+	    - lan966x-switch (LAN966X_SWITCH)
+
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index a9f94525e181..885b22989580 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -71,4 +71,7 @@ obj-$(CONFIG_TPS6594_ESM)	+= tps6594-esm.o
 obj-$(CONFIG_TPS6594_PFSM)	+= tps6594-pfsm.o
 obj-$(CONFIG_NSM)		+= nsm.o
 obj-$(CONFIG_MARVELL_CN10K_DPI)	+= mrvl_cn10k_dpi.o
+lan966x-pci-objs		:= lan966x_pci.o
+lan966x-pci-objs		+= lan966x_pci.dtbo.o
+obj-$(CONFIG_MCHP_LAN966X_PCI)	+= lan966x-pci.o
 obj-y				+= keba/
diff --git a/drivers/misc/lan966x_pci.c b/drivers/misc/lan966x_pci.c
new file mode 100644
index 000000000000..9c79b58137e5
--- /dev/null
+++ b/drivers/misc/lan966x_pci.c
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Microchip LAN966x PCI driver
+ *
+ * Copyright (c) 2024 Microchip Technology Inc. and its subsidiaries.
+ *
+ * Authors:
+ *	Clément Léger <clement.leger@bootlin.com>
+ *	Hervé Codina <herve.codina@bootlin.com>
+ */
+
+#include <linux/device.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+#include <linux/slab.h>
+
+/* Embedded dtbo symbols created by cmd_wrap_S_dtb in scripts/Makefile.lib */
+extern char __dtbo_lan966x_pci_begin[];
+extern char __dtbo_lan966x_pci_end[];
+
+struct pci_dev_intr_ctrl {
+	struct pci_dev *pci_dev;
+	struct irq_domain *irq_domain;
+	int irq;
+};
+
+static int pci_dev_irq_domain_map(struct irq_domain *d, unsigned int virq, irq_hw_number_t hw)
+{
+	irq_set_chip_and_handler(virq, &dummy_irq_chip, handle_simple_irq);
+	return 0;
+}
+
+static const struct irq_domain_ops pci_dev_irq_domain_ops = {
+	.map = pci_dev_irq_domain_map,
+	.xlate = irq_domain_xlate_onecell,
+};
+
+static irqreturn_t pci_dev_irq_handler(int irq, void *data)
+{
+	struct pci_dev_intr_ctrl *intr_ctrl = data;
+	int ret;
+
+	ret = generic_handle_domain_irq(intr_ctrl->irq_domain, 0);
+	return ret ? IRQ_NONE : IRQ_HANDLED;
+}
+
+static struct pci_dev_intr_ctrl *pci_dev_create_intr_ctrl(struct pci_dev *pdev)
+{
+	struct pci_dev_intr_ctrl *intr_ctrl __free(kfree) = NULL;
+	struct fwnode_handle *fwnode;
+	int ret;
+
+	fwnode = dev_fwnode(&pdev->dev);
+	if (!fwnode)
+		return ERR_PTR(-ENODEV);
+
+	intr_ctrl = kmalloc(sizeof(*intr_ctrl), GFP_KERNEL);
+	if (!intr_ctrl)
+		return ERR_PTR(-ENOMEM);
+
+	intr_ctrl->pci_dev = pdev;
+
+	intr_ctrl->irq_domain = irq_domain_create_linear(fwnode, 1, &pci_dev_irq_domain_ops,
+							 intr_ctrl);
+	if (!intr_ctrl->irq_domain) {
+		pci_err(pdev, "Failed to create irqdomain\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_INTX);
+	if (ret < 0) {
+		pci_err(pdev, "Unable alloc irq vector (%d)\n", ret);
+		goto err_remove_domain;
+	}
+	intr_ctrl->irq = pci_irq_vector(pdev, 0);
+	ret = request_irq(intr_ctrl->irq, pci_dev_irq_handler, IRQF_SHARED,
+			  pci_name(pdev), intr_ctrl);
+	if (ret) {
+		pci_err(pdev, "Unable to request irq %d (%d)\n", intr_ctrl->irq, ret);
+		goto err_free_irq_vector;
+	}
+
+	return_ptr(intr_ctrl);
+
+err_free_irq_vector:
+	pci_free_irq_vectors(pdev);
+err_remove_domain:
+	irq_domain_remove(intr_ctrl->irq_domain);
+	return ERR_PTR(ret);
+}
+
+static void pci_dev_remove_intr_ctrl(struct pci_dev_intr_ctrl *intr_ctrl)
+{
+	free_irq(intr_ctrl->irq, intr_ctrl);
+	pci_free_irq_vectors(intr_ctrl->pci_dev);
+	irq_dispose_mapping(irq_find_mapping(intr_ctrl->irq_domain, 0));
+	irq_domain_remove(intr_ctrl->irq_domain);
+	kfree(intr_ctrl);
+}
+
+static void devm_pci_dev_remove_intr_ctrl(void *intr_ctrl)
+{
+	pci_dev_remove_intr_ctrl(intr_ctrl);
+}
+
+static int devm_pci_dev_create_intr_ctrl(struct pci_dev *pdev)
+{
+	struct pci_dev_intr_ctrl *intr_ctrl;
+
+	intr_ctrl = pci_dev_create_intr_ctrl(pdev);
+	if (IS_ERR(intr_ctrl))
+		return PTR_ERR(intr_ctrl);
+
+	return devm_add_action_or_reset(&pdev->dev, devm_pci_dev_remove_intr_ctrl, intr_ctrl);
+}
+
+struct lan966x_pci {
+	struct device *dev;
+	int ovcs_id;
+};
+
+static int lan966x_pci_load_overlay(struct lan966x_pci *data)
+{
+	u32 dtbo_size = __dtbo_lan966x_pci_end - __dtbo_lan966x_pci_begin;
+	void *dtbo_start = __dtbo_lan966x_pci_begin;
+
+	return of_overlay_fdt_apply(dtbo_start, dtbo_size, &data->ovcs_id, dev_of_node(data->dev));
+}
+
+static void lan966x_pci_unload_overlay(struct lan966x_pci *data)
+{
+	of_overlay_remove(&data->ovcs_id);
+}
+
+static int lan966x_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct device *dev = &pdev->dev;
+	struct lan966x_pci *data;
+	int ret;
+
+	/*
+	 * On ACPI system, fwnode can point to the ACPI node.
+	 * This driver needs an of_node to be used as the device-tree overlay
+	 * target. This of_node should be set by the PCI core if it succeeds in
+	 * creating it (CONFIG_PCI_DYNAMIC_OF_NODES feature).
+	 * Check here for the validity of this of_node.
+	 */
+	if (!dev_of_node(dev))
+		return dev_err_probe(dev, -EINVAL, "Missing of_node for device\n");
+
+	/* Need to be done before devm_pci_dev_create_intr_ctrl.
+	 * It allocates an IRQ and so pdev->irq is updated.
+	 */
+	ret = pcim_enable_device(pdev);
+	if (ret)
+		return ret;
+
+	ret = devm_pci_dev_create_intr_ctrl(pdev);
+	if (ret)
+		return ret;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	pci_set_drvdata(pdev, data);
+	data->dev = dev;
+
+	ret = lan966x_pci_load_overlay(data);
+	if (ret)
+		return ret;
+
+	pci_set_master(pdev);
+
+	ret = of_platform_default_populate(dev_of_node(dev), NULL, dev);
+	if (ret)
+		goto err_unload_overlay;
+
+	return 0;
+
+err_unload_overlay:
+	lan966x_pci_unload_overlay(data);
+	return ret;
+}
+
+static void lan966x_pci_remove(struct pci_dev *pdev)
+{
+	struct lan966x_pci *data = pci_get_drvdata(pdev);
+
+	of_platform_depopulate(data->dev);
+
+	lan966x_pci_unload_overlay(data);
+}
+
+static struct pci_device_id lan966x_pci_ids[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_EFAR, 0x9660) },
+	{ }
+};
+MODULE_DEVICE_TABLE(pci, lan966x_pci_ids);
+
+static struct pci_driver lan966x_pci_driver = {
+	.name = "mchp_lan966x_pci",
+	.id_table = lan966x_pci_ids,
+	.probe = lan966x_pci_probe,
+	.remove = lan966x_pci_remove,
+};
+module_pci_driver(lan966x_pci_driver);
+
+MODULE_AUTHOR("Herve Codina <herve.codina@bootlin.com>");
+MODULE_DESCRIPTION("Microchip LAN966x PCI driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/misc/lan966x_pci.dtso b/drivers/misc/lan966x_pci.dtso
new file mode 100644
index 000000000000..7b196b0a0eb6
--- /dev/null
+++ b/drivers/misc/lan966x_pci.dtso
@@ -0,0 +1,177 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Microchip UNG
+ */
+
+#include <dt-bindings/clock/microchip,lan966x.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/phy/phy-lan966x-serdes.h>
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	fragment@0 {
+		target-path = "";
+
+		/*
+		 * These properties allow to avoid a dtc warnings.
+		 * The real interrupt controller is the PCI device itself. It
+		 * is the node on which the device tree overlay will be applied.
+		 * This node has those properties.
+		 */
+		#interrupt-cells = <1>;
+		interrupt-controller;
+
+		__overlay__ {
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			cpu_clk: clock-600000000 {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <600000000>;  /* CPU clock = 600MHz */
+			};
+
+			ddr_clk: clock-30000000 {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <30000000>;  /* Fabric clock = 30MHz */
+			};
+
+			sys_clk: clock-15625000 {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <15625000>;  /* System clock = 15.625MHz */
+			};
+
+			pci-ep-bus@0 {
+				compatible = "simple-bus";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				/*
+				 * map @0xe2000000 (32MB) to BAR0 (CPU)
+				 * map @0xe0000000 (16MB) to BAR1 (AMBA)
+				 */
+				ranges = <0xe2000000 0x00 0x00 0x00 0x2000000
+				          0xe0000000 0x01 0x00 0x00 0x1000000>;
+
+				oic: oic@e00c0120 {
+					compatible = "microchip,lan966x-oic";
+					#interrupt-cells = <2>;
+					interrupt-controller;
+					interrupts = <0>; /* PCI INTx assigned interrupt */
+					reg = <0xe00c0120 0x190>;
+				};
+
+				cpu_ctrl: syscon@e00c0000 {
+					compatible = "microchip,lan966x-cpu-syscon", "syscon";
+					reg = <0xe00c0000 0xa8>;
+				};
+
+				reset: reset@e200400c {
+					compatible = "microchip,lan966x-switch-reset";
+					reg = <0xe200400c 0x4>, <0xe00c0000 0xa8>;
+					reg-names = "gcb","cpu";
+					#reset-cells = <1>;
+					cpu-syscon = <&cpu_ctrl>;
+				};
+
+				gpio: pinctrl@e2004064 {
+					compatible = "microchip,lan966x-pinctrl";
+					reg = <0xe2004064 0xb4>,
+					      <0xe2010024 0x138>;
+					resets = <&reset 0>;
+					reset-names = "switch";
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&gpio 0 0 78>;
+					interrupt-parent = <&oic>;
+					interrupt-controller;
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+					#interrupt-cells = <2>;
+
+					tod_pins: tod_pins {
+						pins = "GPIO_36";
+						function = "ptpsync_1";
+					};
+
+					fc0_a_pins: fcb4-i2c-pins {
+						/* RXD, TXD */
+						pins = "GPIO_9", "GPIO_10";
+						function = "fc0_a";
+					};
+
+				};
+
+				serdes: serdes@e202c000 {
+					compatible = "microchip,lan966x-serdes";
+					reg = <0xe202c000 0x9c>,
+					      <0xe2004010 0x4>;
+					#phy-cells = <2>;
+				};
+
+				mdio1: mdio@e200413c {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "microchip,lan966x-miim";
+					reg = <0xe200413c 0x24>,
+					      <0xe2010020 0x4>;
+
+					resets = <&reset 0>;
+					reset-names = "switch";
+
+					lan966x_phy0: ethernet-lan966x_phy@1 {
+						reg = <1>;
+					};
+
+					lan966x_phy1: ethernet-lan966x_phy@2 {
+						reg = <2>;
+					};
+				};
+
+				switch: switch@e0000000 {
+					compatible = "microchip,lan966x-switch";
+					reg = <0xe0000000 0x0100000>,
+					      <0xe2000000 0x0800000>;
+					reg-names = "cpu", "gcb";
+
+					interrupt-parent = <&oic>;
+					interrupts = <12 IRQ_TYPE_LEVEL_HIGH>,
+						     <9 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "xtr", "ana";
+
+					resets = <&reset 0>;
+					reset-names = "switch";
+
+					pinctrl-names = "default";
+					pinctrl-0 = <&tod_pins>;
+
+					ethernet-ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port0: port@0 {
+							phy-handle = <&lan966x_phy0>;
+
+							reg = <0>;
+							phy-mode = "gmii";
+							phys = <&serdes 0 CU(0)>;
+						};
+
+						port1: port@1 {
+							phy-handle = <&lan966x_phy1>;
+
+							reg = <1>;
+							phy-mode = "gmii";
+							phys = <&serdes 1 CU(1)>;
+						};
+					};
+				};
+			};
+		};
+	};
+};