regulator: da9063: Add support for full-current mode.

In addition to the ability of merging some power outputs, this chip has
an overdrive mode.
BCORE1, BCORE2 and BPRO have this ability, in which case the legal
current draw is increased from 2 amps to 2.5 amps (at the expense of
a quiescent current increase), and the configurable current limits
are doubled.
If a current higher than maximum half-current mode is requested, enable
overdrive, and scale the current limit down.
Symmetrically, scale the current limit up when querying a overdrive-enabled
regulator.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/824518e6391b783a12eba9ff0527f06607a34bfb.1626160826.git.plr.vincent@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

1 files changed, 130 insertions, 2 deletions

diff --git a/drivers/regulator/da9063-regulator.c b/drivers/regulator/da9063-regulator.c
index cf7d5341750e..82f52a2a031a 100644
--- a/drivers/regulator/da9063-regulator.c
+++ b/drivers/regulator/da9063-regulator.c
@@ -412,6 +412,134 @@ static int da9063_ldo_set_suspend_mode(struct regulator_dev *rdev,
 	return regmap_field_write(regl->suspend_sleep, val);
 }
 
+static unsigned int da9063_get_overdrive_mask(const struct regulator_desc *desc)
+{
+	switch (desc->id) {
+	case DA9063_ID_BCORES_MERGED:
+	case DA9063_ID_BCORE1:
+		return DA9063_BCORE1_OD;
+	case DA9063_ID_BCORE2:
+		return DA9063_BCORE2_OD;
+	case DA9063_ID_BPRO:
+		return DA9063_BPRO_OD;
+	default:
+		return 0;
+	}
+}
+
+static int da9063_buck_set_limit_set_overdrive(struct regulator_dev *rdev,
+					       int min_uA, int max_uA,
+					       unsigned int overdrive_mask)
+{
+	/*
+	 * When enabling overdrive, do it before changing the current limit to
+	 * ensure sufficient supply throughout the switch.
+	 */
+	struct da9063_regulator *regl = rdev_get_drvdata(rdev);
+	int ret;
+	unsigned int orig_overdrive;
+
+	ret = regmap_read(regl->hw->regmap, DA9063_REG_CONFIG_H,
+			  &orig_overdrive);
+	if (ret < 0)
+		return ret;
+	orig_overdrive &= overdrive_mask;
+
+	if (orig_overdrive == 0) {
+		ret = regmap_set_bits(regl->hw->regmap, DA9063_REG_CONFIG_H,
+				overdrive_mask);
+		if (ret < 0)
+			return ret;
+	}
+
+	ret = regulator_set_current_limit_regmap(rdev, min_uA / 2, max_uA / 2);
+	if (ret < 0 && orig_overdrive == 0)
+		/*
+		 * regulator_set_current_limit_regmap may have rejected the
+		 * change because of unusable min_uA and/or max_uA inputs.
+		 * Attempt to restore original overdrive state, ignore failure-
+		 * on-failure.
+		 */
+		regmap_clear_bits(regl->hw->regmap, DA9063_REG_CONFIG_H,
+				  overdrive_mask);
+
+	return ret;
+}
+
+static int da9063_buck_set_limit_clear_overdrive(struct regulator_dev *rdev,
+						 int min_uA, int max_uA,
+						 unsigned int overdrive_mask)
+{
+	/*
+	 * When disabling overdrive, do it after changing the current limit to
+	 * ensure sufficient supply throughout the switch.
+	 */
+	struct da9063_regulator *regl = rdev_get_drvdata(rdev);
+	int ret, orig_limit;
+
+	ret = regmap_read(rdev->regmap, rdev->desc->csel_reg, &orig_limit);
+	if (ret < 0)
+		return ret;
+
+	ret = regulator_set_current_limit_regmap(rdev, min_uA, max_uA);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_clear_bits(regl->hw->regmap, DA9063_REG_CONFIG_H,
+				overdrive_mask);
+	if (ret < 0)
+		/*
+		 * Attempt to restore original current limit, ignore failure-
+		 * on-failure.
+		 */
+		regmap_write(rdev->regmap, rdev->desc->csel_reg, orig_limit);
+
+	return ret;
+}
+
+static int da9063_buck_set_current_limit(struct regulator_dev *rdev,
+					 int min_uA, int max_uA)
+{
+	unsigned int overdrive_mask, n_currents;
+
+	overdrive_mask = da9063_get_overdrive_mask(rdev->desc);
+	if (overdrive_mask) {
+		n_currents = rdev->desc->n_current_limits;
+		if (n_currents == 0)
+			return -EINVAL;
+
+		if (max_uA > rdev->desc->curr_table[n_currents - 1])
+			return da9063_buck_set_limit_set_overdrive(rdev, min_uA,
+								   max_uA,
+								   overdrive_mask);
+
+		return da9063_buck_set_limit_clear_overdrive(rdev, min_uA,
+							     max_uA,
+							     overdrive_mask);
+	}
+	return regulator_set_current_limit_regmap(rdev, min_uA, max_uA);
+}
+
+static int da9063_buck_get_current_limit(struct regulator_dev *rdev)
+{
+	struct da9063_regulator *regl = rdev_get_drvdata(rdev);
+	int val, ret, limit;
+	unsigned int mask;
+
+	limit = regulator_get_current_limit_regmap(rdev);
+	if (limit < 0)
+		return limit;
+	mask = da9063_get_overdrive_mask(rdev->desc);
+	if (mask) {
+		ret = regmap_read(regl->hw->regmap, DA9063_REG_CONFIG_H, &val);
+		if (ret < 0)
+			return ret;
+		if (val & mask)
+			limit *= 2;
+	}
+	return limit;
+}
+
 static const struct regulator_ops da9063_buck_ops = {
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
@@ -419,8 +547,8 @@ static const struct regulator_ops da9063_buck_ops = {
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
 	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
 	.list_voltage		= regulator_list_voltage_linear,
-	.set_current_limit	= regulator_set_current_limit_regmap,
-	.get_current_limit	= regulator_get_current_limit_regmap,
+	.set_current_limit	= da9063_buck_set_current_limit,
+	.get_current_limit	= da9063_buck_get_current_limit,
 	.set_mode		= da9063_buck_set_mode,
 	.get_mode		= da9063_buck_get_mode,
 	.get_status		= da9063_buck_get_status,