scsi: wd7000: remove from tree

The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

1 files changed, 0 insertions, 1657 deletions

diff --git a/drivers/scsi/wd7000.c b/drivers/scsi/wd7000.c
deleted file mode 100644
index 409f959845c4..000000000000
--- a/drivers/scsi/wd7000.c
+++ /dev/null
@@ -1,1657 +0,0 @@
-/* $Id: $
- *  linux/drivers/scsi/wd7000.c
- *
- *  Copyright (C) 1992  Thomas Wuensche
- *	closely related to the aha1542 driver from Tommy Thorn
- *	( as close as different hardware allows on a lowlevel-driver :-) )
- *
- *  Revised (and renamed) by John Boyd <boyd@cis.ohio-state.edu> to
- *  accommodate Eric Youngdale's modifications to scsi.c.  Nov 1992.
- *
- *  Additional changes to support scatter/gather.  Dec. 1992.  tw/jb
- *
- *  No longer tries to reset SCSI bus at boot (it wasn't working anyway).
- *  Rewritten to support multiple host adapters.
- *  Miscellaneous cleanup.
- *  So far, still doesn't do reset or abort correctly, since I have no idea
- *  how to do them with this board (8^(.                      Jan 1994 jb
- *
- * This driver now supports both of the two standard configurations (per
- * the 3.36 Owner's Manual, my latest reference) by the same method as
- * before; namely, by looking for a BIOS signature.  Thus, the location of
- * the BIOS signature determines the board configuration.  Until I have
- * time to do something more flexible, users should stick to one of the
- * following:
- *
- * Standard configuration for single-adapter systems:
- *    - BIOS at CE00h
- *    - I/O base address 350h
- *    - IRQ level 15
- *    - DMA channel 6
- * Standard configuration for a second adapter in a system:
- *    - BIOS at C800h
- *    - I/O base address 330h
- *    - IRQ level 11
- *    - DMA channel 5
- *
- * Anyone who can recompile the kernel is welcome to add others as need
- * arises, but unpredictable results may occur if there are conflicts.
- * In any event, if there are multiple adapters in a system, they MUST
- * use different I/O bases, IRQ levels, and DMA channels, since they will be
- * indistinguishable (and in direct conflict) otherwise.
- *
- *   As a point of information, the NO_OP command toggles the CMD_RDY bit
- * of the status port, and this fact could be used as a test for the I/O
- * base address (or more generally, board detection).  There is an interrupt
- * status port, so IRQ probing could also be done.  I suppose the full
- * DMA diagnostic could be used to detect the DMA channel being used.  I
- * haven't done any of this, though, because I think there's too much of
- * a chance that such explorations could be destructive, if some other
- * board's resources are used inadvertently.  So, call me a wimp, but I
- * don't want to try it.  The only kind of exploration I trust is memory
- * exploration, since it's more certain that reading memory won't be
- * destructive.
- *
- * More to my liking would be a LILO boot command line specification, such
- * as is used by the aha152x driver (and possibly others).  I'll look into
- * it, as I have time...
- *
- *   I get mail occasionally from people who either are using or are
- * considering using a WD7000 with Linux.  There is a variety of
- * nomenclature describing WD7000's.  To the best of my knowledge, the
- * following is a brief summary (from an old WD doc - I don't work for
- * them or anything like that):
- *
- * WD7000-FASST2: This is a WD7000 board with the real-mode SST ROM BIOS
- *        installed.  Last I heard, the BIOS was actually done by Columbia
- *        Data Products.  The BIOS is only used by this driver (and thus
- *        by Linux) to identify the board; none of it can be executed under
- *        Linux.
- *
- * WD7000-ASC: This is the original adapter board, with or without BIOS.
- *        The board uses a WD33C93 or WD33C93A SBIC, which in turn is
- *        controlled by an onboard Z80 processor.  The board interface
- *        visible to the host CPU is defined effectively by the Z80's
- *        firmware, and it is this firmware's revision level that is
- *        determined and reported by this driver.  (The version of the
- *        on-board BIOS is of no interest whatsoever.)  The host CPU has
- *        no access to the SBIC; hence the fact that it is a WD33C93 is
- *        also of no interest to this driver.
- *
- * WD7000-AX:
- * WD7000-MX:
- * WD7000-EX: These are newer versions of the WD7000-ASC.  The -ASC is
- *        largely built from discrete components; these boards use more
- *        integration.  The -AX is an ISA bus board (like the -ASC),
- *        the -MX is an MCA (i.e., PS/2) bus board), and the -EX is an
- *        EISA bus board.
- *
- *  At the time of my documentation, the -?X boards were "future" products,
- *  and were not yet available.  However, I vaguely recall that Thomas
- *  Wuensche had an -AX, so I believe at least it is supported by this
- *  driver.  I have no personal knowledge of either -MX or -EX boards.
- *
- *  P.S. Just recently, I've discovered (directly from WD and Future
- *  Domain) that all but the WD7000-EX have been out of production for
- *  two years now.  FD has production rights to the 7000-EX, and are
- *  producing it under a new name, and with a new BIOS.  If anyone has
- *  one of the FD boards, it would be nice to come up with a signature
- *  for it.
- *                                                           J.B. Jan 1994.
- *
- *
- *  Revisions by Miroslav Zagorac <zaga@fly.cc.fer.hr>
- *
- *  08/24/1996.
- *
- *  Enhancement for wd7000_detect function has been made, so you don't have
- *  to enter BIOS ROM address in initialisation data (see struct Config).
- *  We cannot detect IRQ, DMA and I/O base address for now, so we have to
- *  enter them as arguments while wd_7000 is detected. If someone has IRQ,
- *  DMA or I/O base address set to some other value, he can enter them in
- *  configuration without any problem. Also I wrote a function wd7000_setup,
- *  so now you can enter WD-7000 definition as kernel arguments,
- *  as in lilo.conf:
- *
- *     append="wd7000=IRQ,DMA,IO"
- *
- *  PS: If card BIOS ROM is disabled, function wd7000_detect now will recognize
- *      adapter, unlike the old one. Anyway, BIOS ROM from WD7000 adapter is
- *      useless for Linux. B^)
- *
- *
- *  09/06/1996.
- *
- *  Autodetecting of I/O base address from wd7000_detect function is removed,
- *  some little bugs removed, etc...
- *
- *  Thanks to Roger Scott for driver debugging.
- *
- *  06/07/1997
- *
- *  Added support for /proc file system (/proc/scsi/wd7000/[0...] files).
- *  Now, driver can handle hard disks with capacity >1GB.
- *
- *  01/15/1998
- *
- *  Added support for BUS_ON and BUS_OFF parameters in config line.
- *  Miscellaneous cleanup.
- *
- *  03/01/1998
- *
- *  WD7000 driver now work on kernels >= 2.1.x
- *
- *
- * 12/31/2001 - Arnaldo Carvalho de Melo <acme@conectiva.com.br>
- *
- * use host->host_lock, not io_request_lock, cleanups
- *
- * 2002/10/04 - Alan Cox <alan@lxorguk.ukuu.org.uk>
- *
- * Use dev_id for interrupts, kill __func__ pasting
- * Add a lock for the scb pool, clean up all other cli/sti usage stuff
- * Use the adapter lock for the other places we had the cli's
- *
- * 2002/10/06 - Alan Cox <alan@lxorguk.ukuu.org.uk>
- *
- * Switch to new style error handling
- * Clean up delay to udelay, and yielding sleeps
- * Make host reset actually reset the card
- * Make everything static
- *
- * 2003/02/12 - Christoph Hellwig <hch@infradead.org>
- *
- * Cleaned up host template definition
- * Removed now obsolete wd7000.h
- */
-
-#include <linux/delay.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/spinlock.h>
-#include <linux/ioport.h>
-#include <linux/proc_fs.h>
-#include <linux/blkdev.h>
-#include <linux/init.h>
-#include <linux/stat.h>
-#include <linux/io.h>
-
-#include <asm/dma.h>
-
-#include <scsi/scsi.h>
-#include <scsi/scsi_cmnd.h>
-#include <scsi/scsi_device.h>
-#include <scsi/scsi_host.h>
-#include <scsi/scsicam.h>
-
-
-#undef  WD7000_DEBUG		/* general debug                */
-#ifdef WD7000_DEBUG
-#define dprintk printk
-#else
-#define dprintk	no_printk
-#endif
-
-/*
- *  Mailbox structure sizes.
- *  I prefer to keep the number of ICMBs much larger than the number of
- *  OGMBs.  OGMBs are used very quickly by the driver to start one or
- *  more commands, while ICMBs are used by the host adapter per command.
- */
-#define OGMB_CNT	16
-#define ICMB_CNT	32
-
-/*
- *  Scb's are shared by all active adapters.  So, if they all become busy,
- *  callers may be made to wait in alloc_scbs for them to free.  That can
- *  be avoided by setting MAX_SCBS to NUM_CONFIG * WD7000_Q.  If you'd
- *  rather conserve memory, use a smaller number (> 0, of course) - things
- *  will should still work OK.
- */
-#define MAX_SCBS        32
-
-/*
- *  In this version, sg_tablesize now defaults to WD7000_SG, and will
- *  be set to SG_NONE for older boards.  This is the reverse of the
- *  previous default, and was changed so that the driver-level
- *  scsi_host_template would reflect the driver's support for scatter/
- *  gather.
- *
- *  Also, it has been reported that boards at Revision 6 support scatter/
- *  gather, so the new definition of an "older" board has been changed
- *  accordingly.
- */
-#define WD7000_Q	16
-#define WD7000_SG	16
-
-
-/*
- *  WD7000-specific mailbox structure
- *
- */
-typedef volatile struct mailbox {
-	unchar status;
-	unchar scbptr[3];	/* SCSI-style - MSB first (big endian) */
-} Mailbox;
-
-/*
- *  This structure should contain all per-adapter global data.  I.e., any
- *  new global per-adapter data should put in here.
- */
-typedef struct adapter {
-	struct Scsi_Host *sh;	/* Pointer to Scsi_Host structure    */
-	int iobase;		/* This adapter's I/O base address   */
-	int irq;		/* This adapter's IRQ level          */
-	int dma;		/* This adapter's DMA channel        */
-	int int_counter;	/* This adapter's interrupt counter  */
-	int bus_on;		/* This adapter's BUS_ON time        */
-	int bus_off;		/* This adapter's BUS_OFF time       */
-	struct {		/* This adapter's mailboxes          */
-		Mailbox ogmb[OGMB_CNT];	/* Outgoing mailboxes                */
-		Mailbox icmb[ICMB_CNT];	/* Incoming mailboxes                */
-	} mb;
-	int next_ogmb;		/* to reduce contention at mailboxes */
-	unchar control;		/* shadows CONTROL port value        */
-	unchar rev1, rev2;	/* filled in by wd7000_revision      */
-} Adapter;
-
-/*
- * (linear) base address for ROM BIOS
- */
-static const long wd7000_biosaddr[] = {
-	0xc0000, 0xc2000, 0xc4000, 0xc6000, 0xc8000, 0xca000, 0xcc000, 0xce000,
-	0xd0000, 0xd2000, 0xd4000, 0xd6000, 0xd8000, 0xda000, 0xdc000, 0xde000
-};
-#define NUM_ADDRS ARRAY_SIZE(wd7000_biosaddr)
-
-static const unsigned short wd7000_iobase[] = {
-	0x0300, 0x0308, 0x0310, 0x0318, 0x0320, 0x0328, 0x0330, 0x0338,
-	0x0340, 0x0348, 0x0350, 0x0358, 0x0360, 0x0368, 0x0370, 0x0378,
-	0x0380, 0x0388, 0x0390, 0x0398, 0x03a0, 0x03a8, 0x03b0, 0x03b8,
-	0x03c0, 0x03c8, 0x03d0, 0x03d8, 0x03e0, 0x03e8, 0x03f0, 0x03f8
-};
-#define NUM_IOPORTS ARRAY_SIZE(wd7000_iobase)
-
-static const short wd7000_irq[] = { 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 };
-#define NUM_IRQS ARRAY_SIZE(wd7000_irq)
-
-static const short wd7000_dma[] = { 5, 6, 7 };
-#define NUM_DMAS ARRAY_SIZE(wd7000_dma)
-
-/*
- * The following is set up by wd7000_detect, and used thereafter for
- * proc and other global ookups
- */
-
-#define UNITS	8
-static struct Scsi_Host *wd7000_host[UNITS];
-
-#define BUS_ON    64		/* x 125ns = 8000ns (BIOS default) */
-#define BUS_OFF   15		/* x 125ns = 1875ns (BIOS default) */
-
-/*
- *  Standard Adapter Configurations - used by wd7000_detect
- */
-typedef struct {
-	short irq;		/* IRQ level                                  */
-	short dma;		/* DMA channel                                */
-	unsigned iobase;	/* I/O base address                           */
-	short bus_on;		/* Time that WD7000 spends on the AT-bus when */
-	/* transferring data. BIOS default is 8000ns. */
-	short bus_off;		/* Time that WD7000 spends OFF THE BUS after  */
-	/* while it is transferring data.             */
-	/* BIOS default is 1875ns                     */
-} Config;
-
-/*
- * Add here your configuration...
- */
-static Config configs[] = {
-	{15, 6, 0x350, BUS_ON, BUS_OFF},	/* defaults for single adapter */
-	{11, 5, 0x320, BUS_ON, BUS_OFF},	/* defaults for second adapter */
-	{7, 6, 0x350, BUS_ON, BUS_OFF},	/* My configuration (Zaga)     */
-	{-1, -1, 0x0, BUS_ON, BUS_OFF}	/* Empty slot                  */
-};
-#define NUM_CONFIGS ARRAY_SIZE(configs)
-
-/*
- *  The following list defines strings to look for in the BIOS that identify
- *  it as the WD7000-FASST2 SST BIOS.  I suspect that something should be
- *  added for the Future Domain version.
- */
-typedef struct signature {
-	const char *sig;	/* String to look for            */
-	unsigned long ofs;	/* offset from BIOS base address */
-	unsigned len;		/* length of string              */
-} Signature;
-
-static const Signature signatures[] = {
-	{"SSTBIOS", 0x0000d, 7}	/* "SSTBIOS" @ offset 0x0000d */
-};
-#define NUM_SIGNATURES ARRAY_SIZE(signatures)
-
-
-/*
- *  I/O Port Offsets and Bit Definitions
- *  4 addresses are used.  Those not defined here are reserved.
- */
-#define ASC_STAT        0	/* Status,  Read          */
-#define ASC_COMMAND     0	/* Command, Write         */
-#define ASC_INTR_STAT   1	/* Interrupt Status, Read */
-#define ASC_INTR_ACK    1	/* Acknowledge, Write     */
-#define ASC_CONTROL     2	/* Control, Write         */
-
-/*
- * ASC Status Port
- */
-#define INT_IM		0x80	/* Interrupt Image Flag           */
-#define CMD_RDY		0x40	/* Command Port Ready             */
-#define CMD_REJ		0x20	/* Command Port Byte Rejected     */
-#define ASC_INIT        0x10	/* ASC Initialized Flag           */
-#define ASC_STATMASK    0xf0	/* The lower 4 Bytes are reserved */
-
-/*
- * COMMAND opcodes
- *
- *  Unfortunately, I have no idea how to properly use some of these commands,
- *  as the OEM manual does not make it clear.  I have not been able to use
- *  enable/disable unsolicited interrupts or the reset commands with any
- *  discernible effect whatsoever.  I think they may be related to certain
- *  ICB commands, but again, the OEM manual doesn't make that clear.
- */
-#define NO_OP             0	/* NO-OP toggles CMD_RDY bit in ASC_STAT  */
-#define INITIALIZATION    1	/* initialization (10 bytes)              */
-#define DISABLE_UNS_INTR  2	/* disable unsolicited interrupts         */
-#define ENABLE_UNS_INTR   3	/* enable unsolicited interrupts          */
-#define INTR_ON_FREE_OGMB 4	/* interrupt on free OGMB                 */
-#define SOFT_RESET        5	/* SCSI bus soft reset                    */
-#define HARD_RESET_ACK    6	/* SCSI bus hard reset acknowledge        */
-#define START_OGMB        0x80	/* start command in OGMB (n)              */
-#define SCAN_OGMBS        0xc0	/* start multiple commands, signature (n) */
-				/*    where (n) = lower 6 bits            */
-/*
- * For INITIALIZATION:
- */
-typedef struct initCmd {
-	unchar op;		/* command opcode (= 1)                    */
-	unchar ID;		/* Adapter's SCSI ID                       */
-	unchar bus_on;		/* Bus on time, x 125ns (see below)        */
-	unchar bus_off;		/* Bus off time, ""         ""             */
-	unchar rsvd;		/* Reserved                                */
-	unchar mailboxes[3];	/* Address of Mailboxes, MSB first         */
-	unchar ogmbs;		/* Number of outgoing MBs, max 64, 0,1 = 1 */
-	unchar icmbs;		/* Number of incoming MBs,   ""       ""   */
-} InitCmd;
-
-/*
- * Interrupt Status Port - also returns diagnostic codes at ASC reset
- *
- * if msb is zero, the lower bits are diagnostic status
- * Diagnostics:
- * 01   No diagnostic error occurred
- * 02   RAM failure
- * 03   FIFO R/W failed
- * 04   SBIC register read/write failed
- * 05   Initialization D-FF failed
- * 06   Host IRQ D-FF failed
- * 07   ROM checksum error
- * Interrupt status (bitwise):
- * 10NNNNNN   outgoing mailbox NNNNNN is free
- * 11NNNNNN   incoming mailbox NNNNNN needs service
- */
-#define MB_INTR    0xC0		/* Mailbox Service possible/required */
-#define IMB_INTR   0x40		/* 1 Incoming / 0 Outgoing           */
-#define MB_MASK    0x3f		/* mask for mailbox number           */
-
-/*
- * CONTROL port bits
- */
-#define INT_EN     0x08		/* Interrupt Enable */
-#define DMA_EN     0x04		/* DMA Enable       */
-#define SCSI_RES   0x02		/* SCSI Reset       */
-#define ASC_RES    0x01		/* ASC Reset        */
-
-/*
- * Driver data structures:
- *   - mb and scbs are required for interfacing with the host adapter.
- *     An SCB has extra fields not visible to the adapter; mb's
- *     _cannot_ do this, since the adapter assumes they are contiguous in
- *     memory, 4 bytes each, with ICMBs following OGMBs, and uses this fact
- *     to access them.
- *   - An icb is for host-only (non-SCSI) commands.  ICBs are 16 bytes each;
- *     the additional bytes are used only by the driver.
- *   - For now, a pool of SCBs are kept in global storage by this driver,
- *     and are allocated and freed as needed.
- *
- *  The 7000-FASST2 marks OGMBs empty as soon as it has _started_ a command,
- *  not when it has finished.  Since the SCB must be around for completion,
- *  problems arise when SCBs correspond to OGMBs, which may be reallocated
- *  earlier (or delayed unnecessarily until a command completes).
- *  Mailboxes are used as transient data structures, simply for
- *  carrying SCB addresses to/from the 7000-FASST2.
- *
- *  Note also since SCBs are not "permanently" associated with mailboxes,
- *  there is no need to keep a global list of scsi_cmnd pointers indexed
- *  by OGMB.   Again, SCBs reference their scsi_cmnds directly, so mailbox
- *  indices need not be involved.
- */
-
-/*
- *  WD7000-specific scatter/gather element structure
- */
-typedef struct sgb {
-	unchar len[3];
-	unchar ptr[3];		/* Also SCSI-style - MSB first */
-} Sgb;
-
-typedef struct scb {		/* Command Control Block 5.4.1               */
-	unchar op;		/* Command Control Block Operation Code      */
-	unchar idlun;		/* op=0,2:Target Id, op=1:Initiator Id       */
-	/* Outbound data transfer, length is checked */
-	/* Inbound data transfer, length is checked  */
-	/* Logical Unit Number                       */
-	unchar cdb[12];		/* SCSI Command Block                        */
-	volatile unchar status;	/* SCSI Return Status                        */
-	volatile unchar vue;	/* Vendor Unique Error Code                  */
-	unchar maxlen[3];	/* Maximum Data Transfer Length              */
-	unchar dataptr[3];	/* SCSI Data Block Pointer                   */
-	unchar linkptr[3];	/* Next Command Link Pointer                 */
-	unchar direc;		/* Transfer Direction                        */
-	unchar reserved2[6];	/* SCSI Command Descriptor Block             */
-	/* end of hardware SCB                       */
-	struct scsi_cmnd *SCpnt;/* scsi_cmnd using this SCB                  */
-	Sgb sgb[WD7000_SG];	/* Scatter/gather list for this SCB          */
-	Adapter *host;		/* host adapter                              */
-	struct scb *next;	/* for lists of scbs                         */
-} Scb;
-
-/*
- *  This driver is written to allow host-only commands to be executed.
- *  These use a 16-byte block called an ICB.  The format is extended by the
- *  driver to 18 bytes, to support the status returned in the ICMB and
- *  an execution phase code.
- *
- *  There are other formats besides these; these are the ones I've tried
- *  to use.  Formats for some of the defined ICB opcodes are not defined
- *  (notably, get/set unsolicited interrupt status) in my copy of the OEM
- *  manual, and others are ambiguous/hard to follow.
- */
-#define ICB_OP_MASK           0x80	/* distinguishes scbs from icbs        */
-#define ICB_OP_OPEN_RBUF      0x80	/* open receive buffer                 */
-#define ICB_OP_RECV_CMD       0x81	/* receive command from initiator      */
-#define ICB_OP_RECV_DATA      0x82	/* receive data from initiator         */
-#define ICB_OP_RECV_SDATA     0x83	/* receive data with status from init. */
-#define ICB_OP_SEND_DATA      0x84	/* send data with status to initiator  */
-#define ICB_OP_SEND_STAT      0x86	/* send command status to initiator    */
-					/* 0x87 is reserved                    */
-#define ICB_OP_READ_INIT      0x88	/* read initialization bytes           */
-#define ICB_OP_READ_ID        0x89	/* read adapter's SCSI ID              */
-#define ICB_OP_SET_UMASK      0x8A	/* set unsolicited interrupt mask      */
-#define ICB_OP_GET_UMASK      0x8B	/* read unsolicited interrupt mask     */
-#define ICB_OP_GET_REVISION   0x8C	/* read firmware revision level        */
-#define ICB_OP_DIAGNOSTICS    0x8D	/* execute diagnostics                 */
-#define ICB_OP_SET_EPARMS     0x8E	/* set execution parameters            */
-#define ICB_OP_GET_EPARMS     0x8F	/* read execution parameters           */
-
-typedef struct icbRecvCmd {
-	unchar op;
-	unchar IDlun;		/* Initiator SCSI ID/lun     */
-	unchar len[3];		/* command buffer length     */
-	unchar ptr[3];		/* command buffer address    */
-	unchar rsvd[7];		/* reserved                  */
-	volatile unchar vue;	/* vendor-unique error code  */
-	volatile unchar status;	/* returned (icmb) status    */
-	volatile unchar phase;	/* used by interrupt handler */
-} IcbRecvCmd;
-
-typedef struct icbSendStat {
-	unchar op;
-	unchar IDlun;		/* Target SCSI ID/lun                  */
-	unchar stat;		/* (outgoing) completion status byte 1 */
-	unchar rsvd[12];	/* reserved                            */
-	volatile unchar vue;	/* vendor-unique error code            */
-	volatile unchar status;	/* returned (icmb) status              */
-	volatile unchar phase;	/* used by interrupt handler           */
-} IcbSendStat;
-
-typedef struct icbRevLvl {
-	unchar op;
-	volatile unchar primary;	/* primary revision level (returned)   */
-	volatile unchar secondary;	/* secondary revision level (returned) */
-	unchar rsvd[12];	/* reserved                            */
-	volatile unchar vue;	/* vendor-unique error code            */
-	volatile unchar status;	/* returned (icmb) status              */
-	volatile unchar phase;	/* used by interrupt handler           */
-} IcbRevLvl;
-
-typedef struct icbUnsMask {	/* I'm totally guessing here */
-	unchar op;
-	volatile unchar mask[14];	/* mask bits                 */
-#if 0
-	unchar rsvd[12];	/* reserved                  */
-#endif
-	volatile unchar vue;	/* vendor-unique error code  */
-	volatile unchar status;	/* returned (icmb) status    */
-	volatile unchar phase;	/* used by interrupt handler */
-} IcbUnsMask;
-
-typedef struct icbDiag {
-	unchar op;
-	unchar type;		/* diagnostics type code (0-3) */
-	unchar len[3];		/* buffer length               */
-	unchar ptr[3];		/* buffer address              */
-	unchar rsvd[7];		/* reserved                    */
-	volatile unchar vue;	/* vendor-unique error code    */
-	volatile unchar status;	/* returned (icmb) status      */
-	volatile unchar phase;	/* used by interrupt handler   */
-} IcbDiag;
-
-#define ICB_DIAG_POWERUP   0	/* Power-up diags only       */
-#define ICB_DIAG_WALKING   1	/* walking 1's pattern       */
-#define ICB_DIAG_DMA       2	/* DMA - system memory diags */
-#define ICB_DIAG_FULL      3	/* do both 1 & 2             */
-
-typedef struct icbParms {
-	unchar op;
-	unchar rsvd1;		/* reserved                  */
-	unchar len[3];		/* parms buffer length       */
-	unchar ptr[3];		/* parms buffer address      */
-	unchar idx[2];		/* index (MSB-LSB)           */
-	unchar rsvd2[5];	/* reserved                  */
-	volatile unchar vue;	/* vendor-unique error code  */
-	volatile unchar status;	/* returned (icmb) status    */
-	volatile unchar phase;	/* used by interrupt handler */
-} IcbParms;
-
-typedef struct icbAny {
-	unchar op;
-	unchar data[14];	/* format-specific data      */
-	volatile unchar vue;	/* vendor-unique error code  */
-	volatile unchar status;	/* returned (icmb) status    */
-	volatile unchar phase;	/* used by interrupt handler */
-} IcbAny;
-
-typedef union icb {
-	unchar op;		/* ICB opcode                     */
-	IcbRecvCmd recv_cmd;	/* format for receive command     */
-	IcbSendStat send_stat;	/* format for send status         */
-	IcbRevLvl rev_lvl;	/* format for get revision level  */
-	IcbDiag diag;		/* format for execute diagnostics */
-	IcbParms eparms;	/* format for get/set exec parms  */
-	IcbAny icb;		/* generic format                 */
-	unchar data[18];
-} Icb;
-
-#ifdef MODULE
-static char *wd7000;
-module_param(wd7000, charp, 0);
-#endif
-
-/*
- *  Driver SCB structure pool.
- *
- *  The SCBs declared here are shared by all host adapters; hence, this
- *  structure is not part of the Adapter structure.
- */
-static Scb scbs[MAX_SCBS];
-static Scb *scbfree;		/* free list         */
-static int freescbs = MAX_SCBS;	/* free list counter */
-static spinlock_t scbpool_lock;	/* guards the scb free list and count */
-
-/*
- *  END of data/declarations - code follows.
- */
-static void __init setup_error(char *mesg, int *ints)
-{
-	if (ints[0] == 3)
-		printk(KERN_ERR "wd7000_setup: \"wd7000=%d,%d,0x%x\" -> %s\n", ints[1], ints[2], ints[3], mesg);
-	else if (ints[0] == 4)
-		printk(KERN_ERR "wd7000_setup: \"wd7000=%d,%d,0x%x,%d\" -> %s\n", ints[1], ints[2], ints[3], ints[4], mesg);
-	else
-		printk(KERN_ERR "wd7000_setup: \"wd7000=%d,%d,0x%x,%d,%d\" -> %s\n", ints[1], ints[2], ints[3], ints[4], ints[5], mesg);
-}
-
-
-/*
- * Note: You can now set these options from the kernel's "command line".
- * The syntax is:
- *
- *     wd7000=<IRQ>,<DMA>,<IO>[,<BUS_ON>[,<BUS_OFF>]]
- *
- * , where BUS_ON and BUS_OFF are in nanoseconds. BIOS default values
- * are 8000ns for BUS_ON and 1875ns for BUS_OFF.
- * eg:
- *     wd7000=7,6,0x350
- *
- * will configure the driver for a WD-7000 controller
- * using IRQ 15 with a DMA channel 6, at IO base address 0x350.
- */
-static int __init wd7000_setup(char *str)
-{
-	static short wd7000_card_num;	/* .bss will zero this */
-	short i;
-	int ints[6];
-
-	(void) get_options(str, ARRAY_SIZE(ints), ints);
-
-	if (wd7000_card_num >= NUM_CONFIGS) {
-		printk(KERN_ERR "%s: Too many \"wd7000=\" configurations in " "command line!\n", __func__);
-		return 0;
-	}
-
-	if ((ints[0] < 3) || (ints[0] > 5)) {
-		printk(KERN_ERR "%s: Error in command line!  " "Usage: wd7000=<IRQ>,<DMA>,IO>[,<BUS_ON>" "[,<BUS_OFF>]]\n", __func__);
-	} else {
-		for (i = 0; i < NUM_IRQS; i++)
-			if (ints[1] == wd7000_irq[i])
-				break;
-
-		if (i == NUM_IRQS) {
-			setup_error("invalid IRQ.", ints);
-			return 0;
-		} else
-			configs[wd7000_card_num].irq = ints[1];
-
-		for (i = 0; i < NUM_DMAS; i++)
-			if (ints[2] == wd7000_dma[i])
-				break;
-
-		if (i == NUM_DMAS) {
-			setup_error("invalid DMA channel.", ints);
-			return 0;
-		} else
-			configs[wd7000_card_num].dma = ints[2];
-
-		for (i = 0; i < NUM_IOPORTS; i++)
-			if (ints[3] == wd7000_iobase[i])
-				break;
-
-		if (i == NUM_IOPORTS) {
-			setup_error("invalid I/O base address.", ints);
-			return 0;
-		} else
-			configs[wd7000_card_num].iobase = ints[3];
-
-		if (ints[0] > 3) {
-			if ((ints[4] < 500) || (ints[4] > 31875)) {
-				setup_error("BUS_ON value is out of range (500" " to 31875 nanoseconds)!", ints);
-				configs[wd7000_card_num].bus_on = BUS_ON;
-			} else
-				configs[wd7000_card_num].bus_on = ints[4] / 125;
-		} else
-			configs[wd7000_card_num].bus_on = BUS_ON;
-
-		if (ints[0] > 4) {
-			if ((ints[5] < 500) || (ints[5] > 31875)) {
-				setup_error("BUS_OFF value is out of range (500" " to 31875 nanoseconds)!", ints);
-				configs[wd7000_card_num].bus_off = BUS_OFF;
-			} else
-				configs[wd7000_card_num].bus_off = ints[5] / 125;
-		} else
-			configs[wd7000_card_num].bus_off = BUS_OFF;
-
-		if (wd7000_card_num) {
-			for (i = 0; i < (wd7000_card_num - 1); i++) {
-				int j = i + 1;
-
-				for (; j < wd7000_card_num; j++)
-					if (configs[i].irq == configs[j].irq) {
-						setup_error("duplicated IRQ!", ints);
-						return 0;
-					}
-				if (configs[i].dma == configs[j].dma) {
-					setup_error("duplicated DMA " "channel!", ints);
-					return 0;
-				}
-				if (configs[i].iobase == configs[j].iobase) {
-					setup_error("duplicated I/O " "base address!", ints);
-					return 0;
-				}
-			}
-		}
-
-		dprintk(KERN_DEBUG "wd7000_setup: IRQ=%d, DMA=%d, I/O=0x%x, "
-			"BUS_ON=%dns, BUS_OFF=%dns\n", configs[wd7000_card_num].irq, configs[wd7000_card_num].dma, configs[wd7000_card_num].iobase, configs[wd7000_card_num].bus_on * 125, configs[wd7000_card_num].bus_off * 125);
-
-		wd7000_card_num++;
-	}
-	return 1;
-}
-
-__setup("wd7000=", wd7000_setup);
-
-static inline void any2scsi(unchar * scsi, int any)
-{
-	*scsi++ = (unsigned)any >> 16;
-	*scsi++ = (unsigned)any >> 8;
-	*scsi++ = any;
-}
-
-static inline int scsi2int(unchar * scsi)
-{
-	return (scsi[0] << 16) | (scsi[1] << 8) | scsi[2];
-}
-
-static inline void wd7000_enable_intr(Adapter * host)
-{
-	host->control |= INT_EN;
-	outb(host->control, host->iobase + ASC_CONTROL);
-}
-
-
-static inline void wd7000_enable_dma(Adapter * host)
-{
-	unsigned long flags;
-	host->control |= DMA_EN;
-	outb(host->control, host->iobase + ASC_CONTROL);
-
-	flags = claim_dma_lock();
-	set_dma_mode(host->dma, DMA_MODE_CASCADE);
-	enable_dma(host->dma);
-	release_dma_lock(flags);
-
-}
-
-
-#define WAITnexttimeout 200	/* 2 seconds */
-
-static inline short WAIT(unsigned port, unsigned mask, unsigned allof, unsigned noneof)
-{
-	unsigned WAITbits;
-	unsigned long WAITtimeout = jiffies + WAITnexttimeout;
-
-	while (time_before_eq(jiffies, WAITtimeout)) {
-		WAITbits = inb(port) & mask;
-
-		if (((WAITbits & allof) == allof) && ((WAITbits & noneof) == 0))
-			return (0);
-	}
-
-	return (1);
-}
-
-
-static inline int command_out(Adapter * host, unchar * cmd, int len)
-{
-	if (!WAIT(host->iobase + ASC_STAT, ASC_STATMASK, CMD_RDY, 0)) {
-		while (len--) {
-			do {
-				outb(*cmd, host->iobase + ASC_COMMAND);
-				WAIT(host->iobase + ASC_STAT, ASC_STATMASK, CMD_RDY, 0);
-			} while (inb(host->iobase + ASC_STAT) & CMD_REJ);
-
-			cmd++;
-		}
-
-		return (1);
-	}
-
-	printk(KERN_WARNING "wd7000 command_out: WAIT failed(%d)\n", len + 1);
-
-	return (0);
-}
-
-
-/*
- *  This version of alloc_scbs is in preparation for supporting multiple
- *  commands per lun and command chaining, by queueing pending commands.
- *  We will need to allocate Scbs in blocks since they will wait to be
- *  executed so there is the possibility of deadlock otherwise.
- *  Also, to keep larger requests from being starved by smaller requests,
- *  we limit access to this routine with an internal busy flag, so that
- *  the satisfiability of a request is not dependent on the size of the
- *  request.
- */
-static inline Scb *alloc_scbs(struct Scsi_Host *host, int needed)
-{
-	Scb *scb, *p = NULL;
-	unsigned long flags;
-	unsigned long timeout = jiffies + WAITnexttimeout;
-	unsigned long now;
-	int i;
-
-	if (needed <= 0)
-		return (NULL);	/* sanity check */
-
-	spin_unlock_irq(host->host_lock);
-
-      retry:
-	while (freescbs < needed) {
-		timeout = jiffies + WAITnexttimeout;
-		do {
-			/* FIXME: can we actually just yield here ?? */
-			for (now = jiffies; now == jiffies;)
-				cpu_relax();	/* wait a jiffy */
-		} while (freescbs < needed && time_before_eq(jiffies, timeout));
-		/*
-		 *  If we get here with enough free Scbs, we can take them.
-		 *  Otherwise, we timed out and didn't get enough.
-		 */
-		if (freescbs < needed) {
-			printk(KERN_ERR "wd7000: can't get enough free SCBs.\n");
-			return (NULL);
-		}
-	}
-
-	/* Take the lock, then check we didn't get beaten, if so try again */
-	spin_lock_irqsave(&scbpool_lock, flags);
-	if (freescbs < needed) {
-		spin_unlock_irqrestore(&scbpool_lock, flags);
-		goto retry;
-	}
-
-	scb = scbfree;
-	freescbs -= needed;
-	for (i = 0; i < needed; i++) {
-		p = scbfree;
-		scbfree = p->next;
-	}
-	p->next = NULL;
-
-	spin_unlock_irqrestore(&scbpool_lock, flags);
-
-	spin_lock_irq(host->host_lock);
-	return (scb);
-}
-
-
-static inline void free_scb(Scb * scb)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&scbpool_lock, flags);
-
-	memset(scb, 0, sizeof(Scb));
-	scb->next = scbfree;
-	scbfree = scb;
-	freescbs++;
-
-	spin_unlock_irqrestore(&scbpool_lock, flags);
-}
-
-
-static inline void init_scbs(void)
-{
-	int i;
-
-	spin_lock_init(&scbpool_lock);
-
-	/* This is only ever called before the SCB pool is active */
-
-	scbfree = &(scbs[0]);
-	memset(scbs, 0, sizeof(scbs));
-	for (i = 0; i < MAX_SCBS - 1; i++) {
-		scbs[i].next = &(scbs[i + 1]);
-		scbs[i].SCpnt = NULL;
-	}
-	scbs[MAX_SCBS - 1].next = NULL;
-	scbs[MAX_SCBS - 1].SCpnt = NULL;
-}
-
-
-static int mail_out(Adapter * host, Scb * scbptr)
-/*
- *  Note: this can also be used for ICBs; just cast to the parm type.
- */
-{
-	int i, ogmb;
-	unsigned long flags;
-	unchar start_ogmb;
-	Mailbox *ogmbs = host->mb.ogmb;
-	int *next_ogmb = &(host->next_ogmb);
-
-	dprintk("wd7000_mail_out: 0x%06lx", (long) scbptr);
-
-	/* We first look for a free outgoing mailbox */
-	spin_lock_irqsave(host->sh->host_lock, flags);
-	ogmb = *next_ogmb;
-	for (i = 0; i < OGMB_CNT; i++) {
-		if (ogmbs[ogmb].status == 0) {
-			dprintk(" using OGMB 0x%x", ogmb);
-			ogmbs[ogmb].status = 1;
-			any2scsi((unchar *) ogmbs[ogmb].scbptr, (int) scbptr);
-
-			*next_ogmb = (ogmb + 1) % OGMB_CNT;
-			break;
-		} else
-			ogmb = (ogmb + 1) % OGMB_CNT;
-	}
-	spin_unlock_irqrestore(host->sh->host_lock, flags);
-
-	dprintk(", scb is 0x%06lx", (long) scbptr);
-
-	if (i >= OGMB_CNT) {
-		/*
-		 *  Alternatively, we might issue the "interrupt on free OGMB",
-		 *  and sleep, but it must be ensured that it isn't the init
-		 *  task running.  Instead, this version assumes that the caller
-		 *  will be persistent, and try again.  Since it's the adapter
-		 *  that marks OGMB's free, waiting even with interrupts off
-		 *  should work, since they are freed very quickly in most cases.
-		 */
-		dprintk(", no free OGMBs.\n");
-		return (0);
-	}
-
-	wd7000_enable_intr(host);
-
-	start_ogmb = START_OGMB | ogmb;
-	command_out(host, &start_ogmb, 1);
-
-	dprintk(", awaiting interrupt.\n");
-
-	return (1);
-}
-
-
-static int make_code(unsigned hosterr, unsigned scsierr)
-{
-#ifdef WD7000_DEBUG
-	int in_error = hosterr;
-#endif
-
-	switch ((hosterr >> 8) & 0xff) {
-	case 0:		/* Reserved */
-		hosterr = DID_ERROR;
-		break;
-	case 1:		/* Command Complete, no errors */
-		hosterr = DID_OK;
-		break;
-	case 2:		/* Command complete, error logged in scb status (scsierr) */
-		hosterr = DID_OK;
-		break;
-	case 4:		/* Command failed to complete - timeout */
-		hosterr = DID_TIME_OUT;
-		break;
-	case 5:		/* Command terminated; Bus reset by external device */
-		hosterr = DID_RESET;
-		break;
-	case 6:		/* Unexpected Command Received w/ host as target */
-		hosterr = DID_BAD_TARGET;
-		break;
-	case 80:		/* Unexpected Reselection */
-	case 81:		/* Unexpected Selection */
-		hosterr = DID_BAD_INTR;
-		break;
-	case 82:		/* Abort Command Message  */
-		hosterr = DID_ABORT;
-		break;
-	case 83:		/* SCSI Bus Software Reset */
-	case 84:		/* SCSI Bus Hardware Reset */
-		hosterr = DID_RESET;
-		break;
-	default:		/* Reserved */
-		hosterr = DID_ERROR;
-	}
-#ifdef WD7000_DEBUG
-	if (scsierr || hosterr)
-		dprintk("\nSCSI command error: SCSI 0x%02x host 0x%04x return %d\n", scsierr, in_error, hosterr);
-#endif
-	return (scsierr | (hosterr << 16));
-}
-
-#define wd7000_intr_ack(host)   outb (0, host->iobase + ASC_INTR_ACK)
-
-
-static irqreturn_t wd7000_intr(int irq, void *dev_id)
-{
-	Adapter *host = (Adapter *) dev_id;
-	int flag, icmb, errstatus, icmb_status;
-	int host_error, scsi_error;
-	Scb *scb;	/* for SCSI commands */
-	IcbAny *icb;	/* for host commands */
-	struct scsi_cmnd *SCpnt;
-	Mailbox *icmbs = host->mb.icmb;
-	unsigned long flags;
-
-	spin_lock_irqsave(host->sh->host_lock, flags);
-	host->int_counter++;
-
-	dprintk("wd7000_intr: irq = %d, host = 0x%06lx\n", irq, (long) host);
-
-	flag = inb(host->iobase + ASC_INTR_STAT);
-
-	dprintk("wd7000_intr: intr stat = 0x%02x\n", flag);
-
-	if (!(inb(host->iobase + ASC_STAT) & INT_IM)) {
-		/* NB: these are _very_ possible if IRQ 15 is being used, since
-		 * it's the "garbage collector" on the 2nd 8259 PIC.  Specifically,
-		 * any interrupt signal into the 8259 which can't be identified
-		 * comes out as 7 from the 8259, which is 15 to the host.  Thus, it
-		 * is a good thing the WD7000 has an interrupt status port, so we
-		 * can sort these out.  Otherwise, electrical noise and other such
-		 * problems would be indistinguishable from valid interrupts...
-		 */
-		dprintk("wd7000_intr: phantom interrupt...\n");
-		goto ack;
-	}
-
-	if (!(flag & MB_INTR))
-		goto ack;
-
-	/* The interrupt is for a mailbox */
-	if (!(flag & IMB_INTR)) {
-		dprintk("wd7000_intr: free outgoing mailbox\n");
-		/*
-		 * If sleep_on() and the "interrupt on free OGMB" command are
-		 * used in mail_out(), wake_up() should correspondingly be called
-		 * here.  For now, we don't need to do anything special.
-		 */
-		goto ack;
-	}
-
-	/* The interrupt is for an incoming mailbox */
-	icmb = flag & MB_MASK;
-	icmb_status = icmbs[icmb].status;
-	if (icmb_status & 0x80) {	/* unsolicited - result in ICMB */
-		dprintk("wd7000_intr: unsolicited interrupt 0x%02x\n", icmb_status);
-		goto ack;
-	}
-
-	/* Aaaargh! (Zaga) */
-	scb = isa_bus_to_virt(scsi2int((unchar *) icmbs[icmb].scbptr));
-	icmbs[icmb].status = 0;
-	if (scb->op & ICB_OP_MASK) {	/* an SCB is done */
-		icb = (IcbAny *) scb;
-		icb->status = icmb_status;
-		icb->phase = 0;
-		goto ack;
-	}
-
-	SCpnt = scb->SCpnt;
-	if (--(SCpnt->SCp.phase) <= 0) {	/* all scbs are done */
-		host_error = scb->vue | (icmb_status << 8);
-		scsi_error = scb->status;
-		errstatus = make_code(host_error, scsi_error);
-		SCpnt->result = errstatus;
-
-		free_scb(scb);
-
-		SCpnt->scsi_done(SCpnt);
-	}
-
- ack:
-	dprintk("wd7000_intr: return from interrupt handler\n");
-	wd7000_intr_ack(host);
-
-	spin_unlock_irqrestore(host->sh->host_lock, flags);
-	return IRQ_HANDLED;
-}
-
-static int wd7000_queuecommand_lck(struct scsi_cmnd *SCpnt,
-		void (*done)(struct scsi_cmnd *))
-{
-	Scb *scb;
-	Sgb *sgb;
-	unchar *cdb = (unchar *) SCpnt->cmnd;
-	unchar idlun;
-	short cdblen;
-	int nseg;
-	Adapter *host = (Adapter *) SCpnt->device->host->hostdata;
-
-	cdblen = SCpnt->cmd_len;
-	idlun = ((SCpnt->device->id << 5) & 0xe0) | (SCpnt->device->lun & 7);
-	SCpnt->scsi_done = done;
-	SCpnt->SCp.phase = 1;
-	scb = alloc_scbs(SCpnt->device->host, 1);
-	scb->idlun = idlun;
-	memcpy(scb->cdb, cdb, cdblen);
-	scb->direc = 0x40;	/* Disable direction check */
-
-	scb->SCpnt = SCpnt;	/* so we can find stuff later */
-	SCpnt->host_scribble = (unchar *) scb;
-	scb->host = host;
-
-	nseg = scsi_sg_count(SCpnt);
-	if (nseg > 1) {
-		struct scatterlist *sg;
-		unsigned i;
-
-		dprintk("Using scatter/gather with %d elements.\n", nseg);
-
-		sgb = scb->sgb;
-		scb->op = 1;
-		any2scsi(scb->dataptr, (int) sgb);
-		any2scsi(scb->maxlen, nseg * sizeof(Sgb));
-
-		scsi_for_each_sg(SCpnt, sg, nseg, i) {
-			any2scsi(sgb[i].ptr, isa_page_to_bus(sg_page(sg)) + sg->offset);
-			any2scsi(sgb[i].len, sg->length);
-		}
-	} else {
-		scb->op = 0;
-		if (nseg) {
-			struct scatterlist *sg = scsi_sglist(SCpnt);
-			any2scsi(scb->dataptr, isa_page_to_bus(sg_page(sg)) + sg->offset);
-		}
-		any2scsi(scb->maxlen, scsi_bufflen(SCpnt));
-	}
-
-	/* FIXME: drop lock and yield here ? */
-
-	while (!mail_out(host, scb))
-		cpu_relax();	/* keep trying */
-
-	return 0;
-}
-
-static DEF_SCSI_QCMD(wd7000_queuecommand)
-
-static int wd7000_diagnostics(Adapter * host, int code)
-{
-	static IcbDiag icb = { ICB_OP_DIAGNOSTICS };
-	static unchar buf[256];
-	unsigned long timeout;
-
-	icb.type = code;
-	any2scsi(icb.len, sizeof(buf));
-	any2scsi(icb.ptr, (int) &buf);
-	icb.phase = 1;
-	/*
-	 * This routine is only called at init, so there should be OGMBs
-	 * available.  I'm assuming so here.  If this is going to
-	 * fail, I can just let the timeout catch the failure.
-	 */
-	mail_out(host, (struct scb *) &icb);
-	timeout = jiffies + WAITnexttimeout;	/* wait up to 2 seconds */
-	while (icb.phase && time_before(jiffies, timeout)) {
-		cpu_relax();	/* wait for completion */
-		barrier();
-	}
-
-	if (icb.phase) {
-		printk("wd7000_diagnostics: timed out.\n");
-		return (0);
-	}
-	if (make_code(icb.vue | (icb.status << 8), 0)) {
-		printk("wd7000_diagnostics: failed (0x%02x,0x%02x)\n", icb.vue, icb.status);
-		return (0);
-	}
-
-	return (1);
-}
-
-
-static int wd7000_adapter_reset(Adapter * host)
-{
-	InitCmd init_cmd = {
-		INITIALIZATION,
-		7,
-		host->bus_on,
-		host->bus_off,
-		0,
-		{0, 0, 0},
-		OGMB_CNT,
-		ICMB_CNT
-	};
-	int diag;
-	/*
-	 *  Reset the adapter - only.  The SCSI bus was initialized at power-up,
-	 *  and we need to do this just so we control the mailboxes, etc.
-	 */
-	outb(ASC_RES, host->iobase + ASC_CONTROL);
-	udelay(40);		/* reset pulse: this is 40us, only need 25us */
-	outb(0, host->iobase + ASC_CONTROL);
-	host->control = 0;	/* this must always shadow ASC_CONTROL */
-
-	if (WAIT(host->iobase + ASC_STAT, ASC_STATMASK, CMD_RDY, 0)) {
-		printk(KERN_ERR "wd7000_init: WAIT timed out.\n");
-		return -1;	/* -1 = not ok */
-	}
-
-	if ((diag = inb(host->iobase + ASC_INTR_STAT)) != 1) {
-		printk("wd7000_init: ");
-
-		switch (diag) {
-		case 2:
-			printk(KERN_ERR "RAM failure.\n");
-			break;
-		case 3:
-			printk(KERN_ERR "FIFO R/W failed\n");
-			break;
-		case 4:
-			printk(KERN_ERR "SBIC register R/W failed\n");
-			break;
-		case 5:
-			printk(KERN_ERR "Initialization D-FF failed.\n");
-			break;
-		case 6:
-			printk(KERN_ERR "Host IRQ D-FF failed.\n");
-			break;
-		case 7:
-			printk(KERN_ERR "ROM checksum error.\n");
-			break;
-		default:
-			printk(KERN_ERR "diagnostic code 0x%02Xh received.\n", diag);
-		}
-		return -1;
-	}
-	/* Clear mailboxes */
-	memset(&(host->mb), 0, sizeof(host->mb));
-
-	/* Execute init command */
-	any2scsi((unchar *) & (init_cmd.mailboxes), (int) &(host->mb));
-	if (!command_out(host, (unchar *) & init_cmd, sizeof(init_cmd))) {
-		printk(KERN_ERR "wd7000_adapter_reset: adapter initialization failed.\n");
-		return -1;
-	}
-
-	if (WAIT(host->iobase + ASC_STAT, ASC_STATMASK, ASC_INIT, 0)) {
-		printk("wd7000_adapter_reset: WAIT timed out.\n");
-		return -1;
-	}
-	return 0;
-}
-
-static int wd7000_init(Adapter * host)
-{
-	if (wd7000_adapter_reset(host) == -1)
-		return 0;
-
-
-	if (request_irq(host->irq, wd7000_intr, 0, "wd7000", host)) {
-		printk("wd7000_init: can't get IRQ %d.\n", host->irq);
-		return (0);
-	}
-	if (request_dma(host->dma, "wd7000")) {
-		printk("wd7000_init: can't get DMA channel %d.\n", host->dma);
-		free_irq(host->irq, host);
-		return (0);
-	}
-	wd7000_enable_dma(host);
-	wd7000_enable_intr(host);
-
-	if (!wd7000_diagnostics(host, ICB_DIAG_FULL)) {
-		free_dma(host->dma);
-		free_irq(host->irq, NULL);
-		return (0);
-	}
-
-	return (1);
-}
-
-
-static void wd7000_revision(Adapter * host)
-{
-	static IcbRevLvl icb = { ICB_OP_GET_REVISION };
-
-	icb.phase = 1;
-	/*
-	 * Like diagnostics, this is only done at init time, in fact, from
-	 * wd7000_detect, so there should be OGMBs available.  If it fails,
-	 * the only damage will be that the revision will show up as 0.0,
-	 * which in turn means that scatter/gather will be disabled.
-	 */
-	mail_out(host, (struct scb *) &icb);
-	while (icb.phase) {
-		cpu_relax();	/* wait for completion */
-		barrier();
-	}
-	host->rev1 = icb.primary;
-	host->rev2 = icb.secondary;
-}
-
-
-static int wd7000_set_info(struct Scsi_Host *host, char *buffer, int length)
-{
-	dprintk("Buffer = <%.*s>, length = %d\n", length, buffer, length);
-
-	/*
-	 * Currently this is a no-op
-	 */
-	dprintk("Sorry, this function is currently out of order...\n");
-	return (length);
-}
-
-
-static int wd7000_show_info(struct seq_file *m, struct Scsi_Host *host)
-{
-	Adapter *adapter = (Adapter *)host->hostdata;
-	unsigned long flags;
-#ifdef WD7000_DEBUG
-	Mailbox *ogmbs, *icmbs;
-	short count;
-#endif
-
-	spin_lock_irqsave(host->host_lock, flags);
-	seq_printf(m, "Host scsi%d: Western Digital WD-7000 (rev %d.%d)\n", host->host_no, adapter->rev1, adapter->rev2);
-	seq_printf(m, "  IO base:      0x%x\n", adapter->iobase);
-	seq_printf(m, "  IRQ:          %d\n", adapter->irq);
-	seq_printf(m, "  DMA channel:  %d\n", adapter->dma);
-	seq_printf(m, "  Interrupts:   %d\n", adapter->int_counter);
-	seq_printf(m, "  BUS_ON time:  %d nanoseconds\n", adapter->bus_on * 125);
-	seq_printf(m, "  BUS_OFF time: %d nanoseconds\n", adapter->bus_off * 125);
-
-#ifdef WD7000_DEBUG
-	ogmbs = adapter->mb.ogmb;
-	icmbs = adapter->mb.icmb;
-
-	seq_printf(m, "\nControl port value: 0x%x\n", adapter->control);
-	seq_puts(m, "Incoming mailbox:\n");
-	seq_printf(m, "  size: %d\n", ICMB_CNT);
-	seq_puts(m, "  queued messages: ");
-
-	for (i = count = 0; i < ICMB_CNT; i++)
-		if (icmbs[i].status) {
-			count++;
-			seq_printf(m, "0x%x ", i);
-		}
-
-	seq_puts(m, count ? "\n" : "none\n");
-
-	seq_puts(m, "Outgoing mailbox:\n");
-	seq_printf(m, "  size: %d\n", OGMB_CNT);
-	seq_printf(m, "  next message: 0x%x\n", adapter->next_ogmb);
-	seq_puts(m, "  queued messages: ");
-
-	for (i = count = 0; i < OGMB_CNT; i++)
-		if (ogmbs[i].status) {
-			count++;
-			seq_printf(m, "0x%x ", i);
-		}
-
-	seq_puts(m, count ? "\n" : "none\n");
-#endif
-
-	spin_unlock_irqrestore(host->host_lock, flags);
-
-	return 0;
-}
-
-
-/*
- *  Returns the number of adapters this driver is supporting.
- *
- *  The source for hosts.c says to wait to call scsi_register until 100%
- *  sure about an adapter.  We need to do it a little sooner here; we
- *  need the storage set up by scsi_register before wd7000_init, and
- *  changing the location of an Adapter structure is more trouble than
- *  calling scsi_unregister.
- *
- */
-
-static __init int wd7000_detect(struct scsi_host_template *tpnt)
-{
-	short present = 0, biosaddr_ptr, sig_ptr, i, pass;
-	short biosptr[NUM_CONFIGS];
-	unsigned iobase;
-	Adapter *host = NULL;
-	struct Scsi_Host *sh;
-	int unit = 0;
-
-	dprintk("wd7000_detect: started\n");
-
-#ifdef MODULE
-	if (wd7000)
-		wd7000_setup(wd7000);
-#endif
-
-	for (i = 0; i < UNITS; wd7000_host[i++] = NULL);
-	for (i = 0; i < NUM_CONFIGS; biosptr[i++] = -1);
-
-	tpnt->proc_name = "wd7000";
-	tpnt->show_info = &wd7000_show_info;
-	tpnt->write_info = wd7000_set_info;
-
-	/*
-	 * Set up SCB free list, which is shared by all adapters
-	 */
-	init_scbs();
-
-	for (pass = 0; pass < NUM_CONFIGS; pass++) {
-		/*
-		 * First, search for BIOS SIGNATURE...
-		 */
-		for (biosaddr_ptr = 0; biosaddr_ptr < NUM_ADDRS; biosaddr_ptr++)
-			for (sig_ptr = 0; sig_ptr < NUM_SIGNATURES; sig_ptr++) {
-				for (i = 0; i < pass; i++)
-					if (biosptr[i] == biosaddr_ptr)
-						break;
-
-				if (i == pass) {
-					void __iomem *biosaddr = ioremap(wd7000_biosaddr[biosaddr_ptr] + signatures[sig_ptr].ofs,
-								 signatures[sig_ptr].len);
-					short bios_match = 1;
-
-					if (biosaddr)
-						bios_match = check_signature(biosaddr, signatures[sig_ptr].sig, signatures[sig_ptr].len);
-
-					iounmap(biosaddr);
-
-					if (bios_match)
-						goto bios_matched;
-				}
-			}
-
-	      bios_matched:
-		/*
-		 * BIOS SIGNATURE has been found.
-		 */
-#ifdef WD7000_DEBUG
-		dprintk("wd7000_detect: pass %d\n", pass + 1);
-
-		if (biosaddr_ptr == NUM_ADDRS)
-			dprintk("WD-7000 SST BIOS not detected...\n");
-		else
-			dprintk("WD-7000 SST BIOS detected at 0x%lx: checking...\n", wd7000_biosaddr[biosaddr_ptr]);
-#endif
-
-		if (configs[pass].irq < 0)
-			continue;
-
-		if (unit == UNITS)
-			continue;
-
-		iobase = configs[pass].iobase;
-
-		dprintk("wd7000_detect: check IO 0x%x region...\n", iobase);
-
-		if (request_region(iobase, 4, "wd7000")) {
-
-			dprintk("wd7000_detect: ASC reset (IO 0x%x) ...", iobase);
-			/*
-			 * ASC reset...
-			 */
-			outb(ASC_RES, iobase + ASC_CONTROL);
-			msleep(10);
-			outb(0, iobase + ASC_CONTROL);
-
-			if (WAIT(iobase + ASC_STAT, ASC_STATMASK, CMD_RDY, 0)) {
-				dprintk("failed!\n");
-				goto err_release;
-			} else
-				dprintk("ok!\n");
-
-			if (inb(iobase + ASC_INTR_STAT) == 1) {
-				/*
-				 *  We register here, to get a pointer to the extra space,
-				 *  which we'll use as the Adapter structure (host) for
-				 *  this adapter.  It is located just after the registered
-				 *  Scsi_Host structure (sh), and is located by the empty
-				 *  array hostdata.
-				 */
-				sh = scsi_register(tpnt, sizeof(Adapter));
-				if (sh == NULL)
-					goto err_release;
-
-				host = (Adapter *) sh->hostdata;
-
-				dprintk("wd7000_detect: adapter allocated at 0x%x\n", (int) host);
-				memset(host, 0, sizeof(Adapter));
-
-				host->irq = configs[pass].irq;
-				host->dma = configs[pass].dma;
-				host->iobase = iobase;
-				host->int_counter = 0;
-				host->bus_on = configs[pass].bus_on;
-				host->bus_off = configs[pass].bus_off;
-				host->sh = wd7000_host[unit] = sh;
-				unit++;
-
-				dprintk("wd7000_detect: Trying init WD-7000 card at IO " "0x%x, IRQ %d, DMA %d...\n", host->iobase, host->irq, host->dma);
-
-				if (!wd7000_init(host))	/* Initialization failed */
-					goto err_unregister;
-
-				/*
-				 *  OK from here - we'll use this adapter/configuration.
-				 */
-				wd7000_revision(host);	/* important for scatter/gather */
-
-				/*
-				 *  For boards before rev 6.0, scatter/gather isn't supported.
-				 */
-				if (host->rev1 < 6)
-					sh->sg_tablesize = 1;
-
-				present++;	/* count it */
-
-				if (biosaddr_ptr != NUM_ADDRS)
-					biosptr[pass] = biosaddr_ptr;
-
-				printk(KERN_INFO "Western Digital WD-7000 (rev %d.%d) ", host->rev1, host->rev2);
-				printk("using IO 0x%x, IRQ %d, DMA %d.\n", host->iobase, host->irq, host->dma);
-				printk("  BUS_ON time: %dns, BUS_OFF time: %dns\n", host->bus_on * 125, host->bus_off * 125);
-			}
-		} else
-			dprintk("wd7000_detect: IO 0x%x region already allocated!\n", iobase);
-
-		continue;
-
-	      err_unregister:
-		scsi_unregister(sh);
-	      err_release:
-		release_region(iobase, 4);
-
-	}
-
-	if (!present)
-		printk("Failed initialization of WD-7000 SCSI card!\n");
-
-	return (present);
-}
-
-static int wd7000_release(struct Scsi_Host *shost)
-{
-	if (shost->irq)
-		free_irq(shost->irq, NULL);
-	if (shost->io_port && shost->n_io_port)
-		release_region(shost->io_port, shost->n_io_port);
-	scsi_unregister(shost);
-	return 0;
-}
-
-#if 0
-/*
- *  I have absolutely NO idea how to do an abort with the WD7000...
- */
-static int wd7000_abort(Scsi_Cmnd * SCpnt)
-{
-	Adapter *host = (Adapter *) SCpnt->device->host->hostdata;
-
-	if (inb(host->iobase + ASC_STAT) & INT_IM) {
-		printk("wd7000_abort: lost interrupt\n");
-		wd7000_intr_handle(host->irq, NULL, NULL);
-		return FAILED;
-	}
-	return FAILED;
-}
-#endif
-
-/*
- *  Last resort. Reinitialize the board.
- */
-
-static int wd7000_host_reset(struct scsi_cmnd *SCpnt)
-{
-	Adapter *host = (Adapter *) SCpnt->device->host->hostdata;
-
-	spin_lock_irq(SCpnt->device->host->host_lock);
-
-	if (wd7000_adapter_reset(host) < 0) {
-		spin_unlock_irq(SCpnt->device->host->host_lock);
-		return FAILED;
-	}
-
-	wd7000_enable_intr(host);
-
-	spin_unlock_irq(SCpnt->device->host->host_lock);
-	return SUCCESS;
-}
-
-/*
- *  This was borrowed directly from aha1542.c. (Zaga)
- */
-
-static int wd7000_biosparam(struct scsi_device *sdev,
-		struct block_device *bdev, sector_t capacity, int *ip)
-{
-	char b[BDEVNAME_SIZE];
-
-	dprintk("wd7000_biosparam: dev=%s, size=%llu, ",
-		bdevname(bdev, b), (u64)capacity);
-	(void)b;	/* unused var warning? */
-
-	/*
-	 * try default translation
-	 */
-	ip[0] = 64;
-	ip[1] = 32;
-	ip[2] = capacity >> 11;
-
-	/*
-	 * for disks >1GB do some guessing
-	 */
-	if (ip[2] >= 1024) {
-		int info[3];
-
-		/*
-		 * try to figure out the geometry from the partition table
-		 */
-		if ((scsicam_bios_param(bdev, capacity, info) < 0) || !(((info[0] == 64) && (info[1] == 32)) || ((info[0] == 255) && (info[1] == 63)))) {
-			printk("wd7000_biosparam: unable to verify geometry for disk with >1GB.\n" "                  using extended translation.\n");
-
-			ip[0] = 255;
-			ip[1] = 63;
-			ip[2] = (unsigned long) capacity / (255 * 63);
-		} else {
-			ip[0] = info[0];
-			ip[1] = info[1];
-			ip[2] = info[2];
-
-			if (info[0] == 255)
-				printk(KERN_INFO "%s: current partition table is " "using extended translation.\n", __func__);
-		}
-	}
-
-	dprintk("bios geometry: head=%d, sec=%d, cyl=%d\n", ip[0], ip[1], ip[2]);
-	dprintk("WARNING: check, if the bios geometry is correct.\n");
-
-	return (0);
-}
-
-MODULE_AUTHOR("Thomas Wuensche, John Boyd, Miroslav Zagorac");
-MODULE_DESCRIPTION("Driver for the WD7000 series ISA controllers");
-MODULE_LICENSE("GPL");
-
-static struct scsi_host_template driver_template = {
-	.proc_name		= "wd7000",
-	.show_info		= wd7000_show_info,
-	.write_info		= wd7000_set_info,
-	.name			= "Western Digital WD-7000",
-	.detect			= wd7000_detect,
-	.release		= wd7000_release,
-	.queuecommand		= wd7000_queuecommand,
-	.eh_host_reset_handler	= wd7000_host_reset,
-	.bios_param		= wd7000_biosparam,
-	.can_queue		= WD7000_Q,
-	.this_id		= 7,
-	.sg_tablesize		= WD7000_SG,
-	.unchecked_isa_dma	= 1,
-	.use_clustering		= ENABLE_CLUSTERING,
-};
-
-#include "scsi_module.c"