summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/arm/tegra/emc.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/arm/tegra/emc.txt')
-rw-r--r--Documentation/devicetree/bindings/arm/tegra/emc.txt100
1 files changed, 100 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/emc.txt
new file mode 100644
index 000000000000..09335f8eee00
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/emc.txt
@@ -0,0 +1,100 @@
+Embedded Memory Controller
+
+Properties:
+- name : Should be emc
+- #address-cells : Should be 1
+- #size-cells : Should be 0
+- compatible : Should contain "nvidia,tegra20-emc".
+- reg : Offset and length of the register set for the device
+- nvidia,use-ram-code : If present, the sub-nodes will be addressed
+ and chosen using the ramcode board selector. If omitted, only one
+ set of tables can be present and said tables will be used
+ irrespective of ram-code configuration.
+
+Child device nodes describe the memory settings for different configurations and clock rates.
+
+Example:
+
+ emc@7000f400 {
+ #address-cells = < 1 >;
+ #size-cells = < 0 >;
+ compatible = "nvidia,tegra20-emc";
+ reg = <0x7000f4000 0x200>;
+ }
+
+
+Embedded Memory Controller ram-code table
+
+If the emc node has the nvidia,use-ram-code property present, then the
+next level of nodes below the emc table are used to specify which settings
+apply for which ram-code settings.
+
+If the emc node lacks the nvidia,use-ram-code property, this level is omitted
+and the tables are stored directly under the emc node (see below).
+
+Properties:
+
+- name : Should be emc-tables
+- nvidia,ram-code : the binary representation of the ram-code board strappings
+ for which this node (and children) are valid.
+
+
+
+Embedded Memory Controller configuration table
+
+This is a table containing the EMC register settings for the various
+operating speeds of the memory controller. They are always located as
+subnodes of the emc controller node.
+
+There are two ways of specifying which tables to use:
+
+* The simplest is if there is just one set of tables in the device tree,
+ and they will always be used (based on which frequency is used).
+ This is the preferred method, especially when firmware can fill in
+ this information based on the specific system information and just
+ pass it on to the kernel.
+
+* The slightly more complex one is when more than one memory configuration
+ might exist on the system. The Tegra20 platform handles this during
+ early boot by selecting one out of possible 4 memory settings based
+ on a 2-pin "ram code" bootstrap setting on the board. The values of
+ these strappings can be read through a register in the SoC, and thus
+ used to select which tables to use.
+
+Properties:
+- name : Should be emc-table
+- compatible : Should contain "nvidia,tegra20-emc-table".
+- reg : either an opaque enumerator to tell different tables apart, or
+ the valid frequency for which the table should be used (in kHz).
+- clock-frequency : the clock frequency for the EMC at which this
+ table should be used (in kHz).
+- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
+ for operation at the 'clock-frequency' setting.
+ The order and contents of the registers are:
+ RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
+ WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
+ PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
+ TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
+ ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
+ ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
+ CFG_CLKTRIM_1, CFG_CLKTRIM_2
+
+ emc-table@166000 {
+ reg = <166000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 166000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
+
+ emc-table@333000 {
+ reg = <333000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 333000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };