1 files changed, 0 insertions, 70 deletions
diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
deleted file mode 100644
index c3a75ac6e59d..000000000000
--- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
+++ /dev/null
@@ -1,70 +0,0 @@
-Amlogic Meson AXG DWC PCIE SoC controller
-
-Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
-It shares common functions with the PCIe DesignWare core driver and
-inherits common properties defined in
-Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
-
-Additional properties are described here:
-
-Required properties:
-- compatible:
-	should contain :
-	- "amlogic,axg-pcie" for AXG SoC Family
-	- "amlogic,g12a-pcie" for G12A SoC Family
-	to identify the core.
-- reg:
-	should contain the configuration address space.
-- reg-names: Must be
-	- "elbi"	External local bus interface registers
-	- "cfg"		Meson specific registers
-	- "config"	PCIe configuration space
-- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
-- clocks: Must contain an entry for each entry in clock-names.
-- clock-names: Must include the following entries:
-	- "pclk"       PCIe GEN 100M PLL clock
-	- "port"       PCIe_x(A or B) RC clock gate
-	- "general"    PCIe Phy clock
-- resets: phandle to the reset lines.
-- reset-names: must contain "port" and "apb"
-       - "port"        Port A or B reset
-       - "apb"         Share APB reset
-- phys: should contain a phandle to the PCIE phy
-- phy-names: must contain "pcie"
-
-- device_type:
-	should be "pci". As specified in snps,dw-pcie.yaml
-
-
-Example configuration:
-
-	pcie: pcie@f9800000 {
-			compatible = "amlogic,axg-pcie", "snps,dw-pcie";
-			reg = <0x0 0xf9800000 0x0 0x400000
-					0x0 0xff646000 0x0 0x2000
-					0x0 0xf9f00000 0x0 0x100000>;
-			reg-names = "elbi", "cfg", "config";
-			reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
-			interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
-			bus-range = <0x0 0xff>;
-			#address-cells = <3>;
-			#size-cells = <2>;
-			device_type = "pci";
-			ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
-
-			clocks = <&clkc CLKID_USB
-					&clkc CLKID_PCIE_A
-					&clkc CLKID_PCIE_CML_EN0>;
-			clock-names = "general",
-					"pclk",
-					"port";
-			resets = <&reset RESET_PCIE_A>,
-				<&reset RESET_PCIE_APB>;
-			reset-names = "port",
-					"apb";
-			phys = <&pcie_phy>;
-			phy-names = "pcie";
-	};