diff options
Diffstat (limited to 'Documentation/devicetree/bindings/power/supply/qcom_smbb.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/power/supply/qcom_smbb.txt | 150 |
1 files changed, 0 insertions, 150 deletions
diff --git a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt deleted file mode 100644 index 06f8a5ddb68e..000000000000 --- a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt +++ /dev/null @@ -1,150 +0,0 @@ -Qualcomm Switch-Mode Battery Charger and Boost - -PROPERTIES -- compatible: - Usage: required - Value type: <stringlist> - Description: Must be one of: - - "qcom,pm8941-charger" - -- reg: - Usage: required - Value type: <prop-encoded-array> - Description: Base address of registers for SMBB block - -- interrupts: - Usage: required - Value type: <prop-encoded-array> - Description: The format of the specifier is defined by the binding document - describing the node's interrupt parent. Must contain one - specifier for each of the following interrupts, in order: - - charge done - - charge fast mode - - charge trickle mode - - battery temperature ok - - battery present - - charger disconnected - - USB-in valid - - DC-in valid - -- interrupt-names: - Usage: required - Value type: <stringlist> - Description: Must contain the following list, strictly ordered: - "chg-done", - "chg-fast", - "chg-trkl", - "bat-temp-ok", - "bat-present", - "chg-gone", - "usb-valid", - "dc-valid" - -- qcom,fast-charge-current-limit: - Usage: optional (default: 1A, or pre-configured value) - Value type: <u32>; uA; range [100mA : 3A] - Description: Maximum charge current; May be clamped to safety limits. - -- qcom,fast-charge-low-threshold-voltage: - Usage: optional (default: 3.2V, or pre-configured value) - Value type: <u32>; uV; range [2.1V : 3.6V] - Description: Battery voltage limit above which fast charging may operate; - Below this value linear or switch-mode auto-trickle-charging - will operate. - -- qcom,fast-charge-high-threshold-voltage: - Usage: optional (default: 4.2V, or pre-configured value) - Value type: <u32>; uV; range [3.24V : 5V] - Description: Battery voltage limit below which fast charging may operate; - The fast charger will attempt to charge the battery to this - voltage. May be clamped to safety limits. - -- qcom,fast-charge-safe-voltage: - Usage: optional (default: 4.2V, or pre-configured value) - Value type: <u32>; uV; range [3.24V : 5V] - Description: Maximum safe battery voltage; May be pre-set by bootloader, in - which case, setting this will harmlessly fail. The property - 'fast-charge-high-watermark' will be clamped by this value. - -- qcom,fast-charge-safe-current: - Usage: optional (default: 1A, or pre-configured value) - Value type: <u32>; uA; range [100mA : 3A] - Description: Maximum safe battery charge current; May pre-set by bootloader, - in which case, setting this will harmlessly fail. The property - 'qcom,fast-charge-current-limit' will be clamped by this value. - -- qcom,auto-recharge-threshold-voltage: - Usage: optional (default: 4.1V, or pre-configured value) - Value type: <u32>; uV; range [3.24V : 5V] - Description: Battery voltage limit below which auto-recharge functionality - will restart charging after end-of-charge; The high cutoff - limit for auto-recharge is 5% above this value. - -- qcom,minimum-input-voltage: - Usage: optional (default: 4.3V, or pre-configured value) - Value type: <u32>; uV; range [4.2V : 9.6V] - Description: Input voltage level above which charging may operate - -- qcom,dc-current-limit: - Usage: optional (default: 100mA, or pre-configured value) - Value type: <u32>; uA; range [100mA : 2.5A] - Description: Default DC charge current limit - -- qcom,disable-dc: - Usage: optional (default: false) - Value type: boolean: <u32> or <empty> - Description: Disable DC charger - -- qcom,jeita-extended-temp-range: - Usage: optional (default: false) - Value type: boolean: <u32> or <empty> - Description: Enable JEITA extended temperature range; This does *not* - adjust the maximum charge voltage or current in the extended - temperature range. It only allows charging when the battery - is in the extended temperature range. Voltage/current - regulation must be done externally to fully comply with - the JEITA safety guidelines if this flag is set. - -- usb_otg_in-supply: - Usage: optional - Value type: <phandle> - Description: Reference to the regulator supplying power to the USB_OTG_IN - pin. - -child nodes: -- otg-vbus: - Usage: optional - Description: This node defines a regulator used to control the direction - of VBUS voltage - specifically: whether to supply voltage - to VBUS for host mode operation of the OTG port, or allow - input voltage from external VBUS for charging. In the - hardware, the supply for this regulator comes from - usb_otg_in-supply. - -EXAMPLE -charger@1000 { - compatible = "qcom,pm8941-charger"; - reg = <0x1000 0x700>; - interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, - <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; - interrupt-names = "chg-done", - "chg-fast", - "chg-trkl", - "bat-temp-ok", - "bat-present", - "chg-gone", - "usb-valid", - "dc-valid"; - - qcom,fast-charge-current-limit = <1000000>; - qcom,dc-charge-current-limit = <1000000>; - usb_otg_in-supply = <&pm8941_5vs1>; - - otg-vbus {}; -}; |