diff options
Diffstat (limited to 'Documentation/devicetree')
24 files changed, 682 insertions, 53 deletions
diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/arm/atmel-adc.txt index 16769d9cedd6..723c205cb10d 100644 --- a/Documentation/devicetree/bindings/arm/atmel-adc.txt +++ b/Documentation/devicetree/bindings/arm/atmel-adc.txt @@ -1,18 +1,15 @@ * AT91's Analog to Digital Converter (ADC) Required properties: - - compatible: Should be "atmel,at91sam9260-adc" + - compatible: Should be "atmel,<chip>-adc" + <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5" - reg: Should contain ADC registers location and length - interrupts: Should contain the IRQ line for the ADC - - atmel,adc-channel-base: Offset of the first channel data register - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this device - - atmel,adc-drdy-mask: Mask of the DRDY interruption in the ADC - atmel,adc-num-channels: Number of channels available in the ADC - atmel,adc-startup-time: Startup Time of the ADC in microseconds as defined in the datasheet - - atmel,adc-status-register: Offset of the Interrupt Status Register - - atmel,adc-trigger-register: Offset of the Trigger Register - atmel,adc-vref: Reference voltage in millivolts for the conversions - atmel,adc-res: List of resolution in bits supported by the ADC. List size must be two at least. diff --git a/Documentation/devicetree/bindings/extcon/extcon-twl.txt b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt index 58f531ab4df3..7dab6a8f4a0e 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-twl.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt @@ -1,15 +1,15 @@ -EXTCON FOR TWL CHIPS +EXTCON FOR PALMAS/TWL CHIPS PALMAS USB COMPARATOR Required Properties: - compatible : Should be "ti,palmas-usb" or "ti,twl6035-usb" - - vbus-supply : phandle to the regulator device tree node. Optional Properties: - ti,wakeup : To enable the wakeup comparator in probe + - ti,enable-id-detection: Perform ID detection. + - ti,enable-vbus-detection: Perform VBUS detection. palmas-usb { compatible = "ti,twl6035-usb", "ti,palmas-usb"; - vbus-supply = <&smps10_reg>; ti,wakeup; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt index a1ee681942cc..6113f9275f42 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt @@ -4,7 +4,7 @@ Required properties : - reg : Offset and length of the register set for the device - - compatible : Should be "marvell,mv64xxx-i2c" + - compatible : Should be "marvell,mv64xxx-i2c" or "allwinner,sun4i-i2c" - interrupts : The interrupt number Optional properties : diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt new file mode 100644 index 000000000000..c5933573e0f6 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt @@ -0,0 +1,24 @@ +* Bosch BMA180 triaxial acceleration sensor + +http://omapworld.com/BMA180_111_1002839.pdf + +Required properties: + + - compatible : should be "bosch,bma180" + - reg : the I2C address of the sensor + +Optional properties: + + - interrupt-parent : should be the phandle for the interrupt controller + + - interrupts : interrupt mapping for GPIO IRQ, it should by configured with + flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING + +Example: + +bma180@40 { + compatible = "bosch,bma180"; + reg = <0x40>; + interrupt-parent = <&gpio6>; + interrupts = <18 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt b/Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt new file mode 100644 index 000000000000..e9582e6fe350 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt @@ -0,0 +1,18 @@ +* Nuvoton NAU7802 Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "nuvoton,nau7802" + - reg: Should contain the ADC I2C address + +Optional properties: + - nuvoton,vldo: Internal reference voltage in millivolts to be + configured valid values are between 2400 mV and 4500 mV. + - interrupts: IRQ line for the ADC. If not used the driver will use + polling. + +Example: +adc2: nau7802@2a { + compatible = "nuvoton,nau7802"; + reg = <0x2a>; + nuvoton,vldo = <3000>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/apds9300.txt b/Documentation/devicetree/bindings/iio/light/apds9300.txt new file mode 100644 index 000000000000..d6f66c73ddbf --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/apds9300.txt @@ -0,0 +1,22 @@ +* Avago APDS9300 ambient light sensor + +http://www.avagotech.com/docs/AV02-1077EN + +Required properties: + + - compatible : should be "avago,apds9300" + - reg : the I2C address of the sensor + +Optional properties: + + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : interrupt mapping for GPIO IRQ + +Example: + +apds9300@39 { + compatible = "avago,apds9300"; + reg = <0x39>; + interrupt-parent = <&gpio2>; + interrupts = <29 8>; +}; diff --git a/Documentation/devicetree/bindings/regulator/88pm800.txt b/Documentation/devicetree/bindings/regulator/88pm800.txt new file mode 100644 index 000000000000..e8a54c2a5821 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/88pm800.txt @@ -0,0 +1,38 @@ +Marvell 88PM800 regulator + +Required properties: +- compatible: "marvell,88pm800" +- reg: I2C slave address +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name (or the deprecated + regulator-compatible property if present), with valid values listed below. + The content of each sub-node is defined by the standard binding for + regulators; see regulator.txt. + +The valid names for regulators are: + + buck1, buck2, buck3, buck4, buck5, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, + ldo8, ldo9, ldo10, ldo11, ldo12, ldo13, ldo14, ldo15, ldo16, ldo17, ldo18, ldo19 + +Example: + + pmic: 88pm800@31 { + compatible = "marvell,88pm800"; + reg = <0x31>; + + regulators { + buck1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3950000>; + regulator-boot-on; + regulator-always-on; + }; + ldo1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <15000000>; + regulator-boot-on; + regulator-always-on; + }; +... + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8660.txt b/Documentation/devicetree/bindings/regulator/max8660.txt new file mode 100644 index 000000000000..8ba994d8a142 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8660.txt @@ -0,0 +1,47 @@ +Maxim MAX8660 voltage regulator + +Required properties: +- compatible: must be one of "maxim,max8660", "maxim,max8661" +- reg: I2C slave address, usually 0x34 +- any required generic properties defined in regulator.txt + +Example: + + i2c_master { + max8660@34 { + compatible = "maxim,max8660"; + reg = <0x34>; + + regulators { + regulator@0 { + regulator-compatible= "V3(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@1 { + regulator-compatible= "V4(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@2 { + regulator-compatible= "V5(LDO)"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + }; + + regulator@3 { + regulator-compatible= "V6(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + regulator@4 { + regulator-compatible= "V7(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt index d5a308629c57..a22e4c70db5c 100644 --- a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt +++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt @@ -25,15 +25,14 @@ Optional nodes: Additional custom properties are listed below. For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP, - smps45, smps457, smps7 depending on variant, smps6, smps[8-10], - ldo[1-9], ldoln, ldousb. + smps45, smps457, smps7 depending on variant, smps6, smps[8-9], + smps10_out2, smps10_out1, do[1-9], ldoln, ldousb. Optional sub-node properties: ti,warm-reset - maintain voltage during warm reset(boolean) ti,roof-floor - control voltage selection by pin(boolean) - ti,sleep-mode - mode to adopt in pmic sleep 0 - off, 1 - auto, + ti,mode-sleep - mode to adopt in pmic sleep 0 - off, 1 - auto, 2 - eco, 3 - forced pwm - ti,tstep - slope control 0 - Jump, 1 10mV/us, 2 5mV/us, 3 2.5mV/us ti,smps-range - OTP has the wrong range set for the hardware so override 0 - low range, 1 - high range. @@ -59,7 +58,6 @@ pmic { ti,warm-reset; ti,roof-floor; ti,mode-sleep = <0>; - ti,tstep = <0>; ti,smps-range = <1>; }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt new file mode 100644 index 000000000000..fc989b2e8057 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -0,0 +1,115 @@ +PFUZE100 family of regulators + +Required properties: +- compatible: "fsl,pfuze100" +- reg: I2C slave address + +Required child node: +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Please refer to below doc + Documentation/devicetree/bindings/regulator/regulator.txt. + + The valid names for regulators are: + sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6 + +Each regulator is defined using the standard binding for regulators. + +Example: + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 48a3b8e5d6bd..2bd8f0978765 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -12,6 +12,8 @@ Optional properties: - regulator-allow-bypass: allow the regulator to go into bypass mode - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) + For hardwares which support disabling ramp rate, it should be explicitly + intialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt new file mode 100644 index 000000000000..a590ca51be75 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -0,0 +1,34 @@ +* Energy Micro EFM32 SPI + +Required properties: +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- compatible: should be "efm32,spi" +- reg: Offset and length of the register set for the controller +- interrupts: pair specifying rx and tx irq +- clocks: phandle to the spi clock +- cs-gpios: see spi-bus.txt +- location: Value to write to the ROUTE register's LOCATION bitfield to configure the pinmux for the device, see datasheet for values. + +Example: + +spi1: spi@0x4000c400 { /* USART1 */ + #address-cells = <1>; + #size-cells = <0>; + compatible = "efm32,spi"; + reg = <0x4000c400 0x400>; + interrupts = <15 16>; + clocks = <&cmu 20>; + cs-gpios = <&gpio 51 1>; // D3 + location = <1>; + status = "ok"; + + ks8851@0 { + compatible = "ks8851"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&boardfpga>; + interrupts = <4>; + status = "ok"; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 296015e3c632..800dafe5b01b 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -55,6 +55,16 @@ contain the following properties. chip select active high - spi-3wire - (optional) Empty property indicating device requires 3-wire mode. +- spi-tx-bus-width - (optional) The bus width(number of data wires) that + used for MOSI. Defaults to 1 if not present. +- spi-rx-bus-width - (optional) The bus width(number of data wires) that + used for MISO. Defaults to 1 if not present. + +Some SPI controllers and devices support Dual and Quad SPI transfer mode. +It allows data in SPI system transfered in 2 wires(DUAL) or 4 wires(QUAD). +Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is +only 1(SINGLE), 2(DUAL) and 4(QUAD). +Dual/Quad mode is not allowed when 3-wire mode is used. If a gpio chipselect is used for the SPI slave the gpio number will be passed via the cs_gpio diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt new file mode 100644 index 000000000000..a1fb3035a42b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -0,0 +1,42 @@ +ARM Freescale DSPI controller + +Required properties: +- compatible : "fsl,vf610-dspi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI controller interrupt +- clocks: from common clock binding: handle to dspi clock. +- clock-names: from common clock binding: Shall be "dspi". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must contain a "default" entry. +- spi-num-chipselects : the number of the chipselect signals. +- bus-num : the slave chip chipselect signal number. +Example: + +dspi0@4002c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-dspi"; + reg = <0x4002c000 0x1000>; + interrupts = <0 67 0x04>; + clocks = <&clks VF610_CLK_DSPI0>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + bus-num = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi0_1>; + status = "okay"; + + sflash: at26df081a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at26df081a"; + spi-max-frequency = <16000000>; + spi-cpol; + spi-cpha; + reg = <0>; + linux,modalias = "m25p80"; + modal = "at26df081a"; + }; +}; + + diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt new file mode 100644 index 000000000000..1f9641ade0b5 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -0,0 +1,22 @@ +TI QSPI controller. + +Required properties: +- compatible : should be "ti,dra7xxx-qspi" or "ti,am4372-qspi". +- reg: Should contain QSPI registers location and length. +- #address-cells, #size-cells : Must be present if the device has sub-nodes +- ti,hwmods: Name of the hwmod associated to the QSPI + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +qspi: qspi@4b300000 { + compatible = "ti,dra7xxx-qspi"; + reg = <0x4b300000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <25000000>; + ti,hwmods = "qspi"; +}; diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt index dc9dc8c87f15..20c2ff2ba07e 100644 --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -1,35 +1,197 @@ -AM33XX MUSB GLUE - - compatible : Should be "ti,musb-am33xx" - - reg : offset and length of register sets, first usbss, then for musb instances - - interrupts : usbss, musb instance interrupts in order - - ti,hwmods : must be "usb_otg_hs" - - multipoint : Should be "1" indicating the musb controller supports - multipoint. This is a MUSB configuration-specific setting. - - num-eps : Specifies the number of endpoints. This is also a - MUSB configuration-specific setting. Should be set to "16" - - ram-bits : Specifies the ram address size. Should be set to "12" - - port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2" - represents PERIPHERAL. - - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2" - represents PERIPHERAL. - - power : Should be "250". This signifies the controller can supply up to - 500mA when operating in host mode. + AM33xx MUSB +~~~~~~~~~~~~~~~ +- compatible: ti,am33xx-usb +- reg: offset and length of the usbss register sets +- ti,hwmods : must be "usb_otg_hs" + +The glue layer contains multiple child nodes. It is required the have +at least a control module node, USB node and a PHY node. The second USB +node and its PHY node is optional. The DMA node is also optional. + +Reset module +~~~~~~~~~~~~ +- compatible: ti,am335x-usb-ctrl-module +- reg: offset and length of the "USB control registers" in the "Control + Module" block. A second offset and length for the USB wake up control + in the same memory block. +- reg-names: "phy_ctrl" for the "USB control registers" and "wakeup" for + the USB wake up control register. + +USB PHY +~~~~~~~ +compatible: ti,am335x-usb-phy +reg: offset and length of the "USB PHY" register space +ti,ctrl_mod: reference to the "reset module" node +reg-names: phy +The PHY should have a "phy" alias numbered properly in the alias +node. + +USB +~~~ +- compatible: ti,musb-am33xx +- reg: offset and length of "USB Controller Registers", and offset and + length of "USB Core" register space. +- reg-names: control for the ""USB Controller Registers" and "mc" for + "USB Core" register space +- interrupts: USB interrupt number +- interrupt-names: mc +- dr_mode: Should be one of "host", "peripheral" or "otg". +- mentor,multipoint: Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. +- mentor,num-eps: Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" +- mentor,ram-bits: Specifies the ram address size. Should be set to "12" +- mentor,power: Should be "500". This signifies the controller can supply up to + 500mA when operating in host mode. +- phys: reference to the USB phy +- dmas: specifies the dma channels +- dma-names: specifies the names of the channels. Use "rxN" for receive + and "txN" for transmit endpoints. N specifies the endpoint number. + +The controller should have an "usb" alias numbered properly in the alias +node. + +DMA +~~~ +- compatible: ti,am3359-cppi41 +- reg: offset and length of the following register spaces: USBSS, USB + CPPI DMA Controller, USB CPPI DMA Scheduler, USB Queue Manager +- reg-names: glue, controller, scheduler, queuemgr +- #dma-cells: should be set to 2. The first number represents the + endpoint number (0 … 14 for endpoints 1 … 15 on instance 0 and 15 … 29 + for endpoints 1 … 15 on instance 1). The second number is 0 for RX and + 1 for TX transfers. +- #dma-channels: should be set to 30 representing the 15 endpoints for + each USB instance. Example: +~~~~~~~~ +The following example contains all the nodes as used on am335x-evm: + +aliases { + usb0 = &usb0; + usb1 = &usb1; + phy0 = &usb0_phy; + phy1 = &usb1_phy; +}; -usb@47400000 { - compatible = "ti,musb-am33xx"; - reg = <0x47400000 0x1000 /* usbss */ - 0x47401000 0x800 /* musb instance 0 */ - 0x47401800 0x800>; /* musb instance 1 */ - interrupts = <17 /* usbss */ - 18 /* musb instance 0 */ - 19>; /* musb instance 1 */ - multipoint = <1>; - num-eps = <16>; - ram-bits = <12>; - port0-mode = <3>; - port1-mode = <3>; - power = <250>; +usb: usb@47400000 { + compatible = "ti,am33xx-usb"; + reg = <0x47400000 0x1000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; ti,hwmods = "usb_otg_hs"; + + ctrl_mod: control@44e10000 { + compatible = "ti,am335x-usb-ctrl-module"; + reg = <0x44e10620 0x10 + 0x44e10648 0x4>; + reg-names = "phy_ctrl", "wakeup"; + }; + + usb0_phy: usb-phy@47401300 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401300 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&ctrl_mod>; + }; + + usb0: usb@47401000 { + compatible = "ti,musb-am33xx"; + reg = <0x47401400 0x400 + 0x47401000 0x200>; + reg-names = "mc", "control"; + + interrupts = <18>; + interrupt-names = "mc"; + dr_mode = "otg" + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb0_phy>; + + dmas = <&cppi41dma 0 0 &cppi41dma 1 0 + &cppi41dma 2 0 &cppi41dma 3 0 + &cppi41dma 4 0 &cppi41dma 5 0 + &cppi41dma 6 0 &cppi41dma 7 0 + &cppi41dma 8 0 &cppi41dma 9 0 + &cppi41dma 10 0 &cppi41dma 11 0 + &cppi41dma 12 0 &cppi41dma 13 0 + &cppi41dma 14 0 &cppi41dma 0 1 + &cppi41dma 1 1 &cppi41dma 2 1 + &cppi41dma 3 1 &cppi41dma 4 1 + &cppi41dma 5 1 &cppi41dma 6 1 + &cppi41dma 7 1 &cppi41dma 8 1 + &cppi41dma 9 1 &cppi41dma 10 1 + &cppi41dma 11 1 &cppi41dma 12 1 + &cppi41dma 13 1 &cppi41dma 14 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + usb1_phy: usb-phy@47401b00 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401b00 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&ctrl_mod>; + }; + + usb1: usb@47401800 { + compatible = "ti,musb-am33xx"; + reg = <0x47401c00 0x400 + 0x47401800 0x200>; + reg-names = "mc", "control"; + interrupts = <19>; + interrupt-names = "mc"; + dr_mode = "host" + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb1_phy>; + + dmas = <&cppi41dma 15 0 &cppi41dma 16 0 + &cppi41dma 17 0 &cppi41dma 18 0 + &cppi41dma 19 0 &cppi41dma 20 0 + &cppi41dma 21 0 &cppi41dma 22 0 + &cppi41dma 23 0 &cppi41dma 24 0 + &cppi41dma 25 0 &cppi41dma 26 0 + &cppi41dma 27 0 &cppi41dma 28 0 + &cppi41dma 29 0 &cppi41dma 15 1 + &cppi41dma 16 1 &cppi41dma 17 1 + &cppi41dma 18 1 &cppi41dma 19 1 + &cppi41dma 20 1 &cppi41dma 21 1 + &cppi41dma 22 1 &cppi41dma 23 1 + &cppi41dma 24 1 &cppi41dma 25 1 + &cppi41dma 26 1 &cppi41dma 27 1 + &cppi41dma 28 1 &cppi41dma 29 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + cppi41dma: dma-controller@07402000 { + compatible = "ti,am3359-cppi41"; + reg = <0x47400000 0x1000 + 0x47402000 0x1000 + 0x47403000 0x1000 + 0x47404000 0x4000>; + reg-names = "glue", "controller", "scheduler", "queuemgr"; + interrupts = <17>; + interrupt-names = "glue"; + #dma-cells = <2>; + #dma-channels = <30>; + #dma-requests = <256>; + }; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 7a95c651ceb3..e807635f9e1c 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -3,10 +3,12 @@ synopsys DWC3 CORE DWC3- USB3 CONTROLLER Required properties: - - compatible: must be "synopsys,dwc3" + - compatible: must be "snps,dwc3" - reg : Address and length of the register set for the device - interrupts: Interrupts used by the dwc3 controller. - - usb-phy : array of phandle for the PHY device + - usb-phy : array of phandle for the PHY device. The first element + in the array is expected to be a handle to the USB2/HS PHY and + the second element is expected to be a handle to the USB3/SS PHY Optional properties: - tx-fifo-resize: determines if the FIFO *has* to be reallocated. @@ -14,7 +16,7 @@ Optional properties: This is usually a subnode to DWC3 glue to which it is connected. dwc3@4a030000 { - compatible = "synopsys,dwc3"; + compatible = "snps,dwc3"; reg = <0x4a030000 0xcfff>; interrupts = <0 92 4> usb-phy = <&usb2_phy>, <&usb3,phy>; diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt new file mode 100644 index 000000000000..477d5bb5e51c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -0,0 +1,24 @@ +Generic USB Properties + +Optional properties: + - maximum-speed: tells USB controllers we want to work up to a certain + speed. Valid arguments are "super-speed", "high-speed", + "full-speed" and "low-speed". In case this isn't passed + via DT, USB controllers should default to their maximum + HW capability. + - dr_mode: tells Dual-Role USB controllers that we want to work on a + particular mode. Valid arguments are "host", + "peripheral" and "otg". In case this attribute isn't + passed via DT, USB DRD controllers should default to + OTG. + +This is an attribute to a USB controller such as: + +dwc3@4a030000 { + compatible = "synopsys,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + maximum-speed = "super-speed"; + dr_mode = "otg"; +}; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt index c4c9e9e664aa..ba797d3e6326 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -3,7 +3,7 @@ Tegra SOC USB PHY The device node for Tegra SOC USB PHY: Required properties : - - compatible : Should be "nvidia,tegra20-usb-phy". + - compatible : Should be "nvidia,tegra<chip>-usb-phy". - reg : Defines the following set of registers, in the order listed: - The PHY's own register set. Always present. @@ -24,17 +24,26 @@ Required properties : Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. -Required PHY timing params for utmi phy: +Required PHY timing params for utmi phy, for all chips: - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before start of sync launches RxActive - nvidia,elastic-limit : Variable FIFO Depth of elastic input store - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait before declare IDLE. - nvidia,term-range-adj : Range adjusment on terminations - - nvidia,xcvr-setup : HS driver output control + - Either one of the following for HS driver output control: + - nvidia,xcvr-setup : integer, uses the provided value. + - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read + from the on-chip fuses + If both are provided, nvidia,xcvr-setup-use-fuses takes precedence. - nvidia,xcvr-lsfslew : LS falling slew rate control. - nvidia,xcvr-lsrslew : LS rising slew rate control. +Required PHY timing params for utmi phy, only on Tegra30 and above: + - nvidia,xcvr-hsslew : HS slew rate control. + - nvidia,hssquelch-level : HS squelch detector level. + - nvidia,hsdiscon-level : HS disconnect detector level. + Optional properties: - nvidia,has-legacy-mode : boolean indicates whether this controller can operate in legacy mode (as APX 2500 / 2600). In legacy mode some @@ -48,5 +57,5 @@ Optional properties: peripheral means it is device controller otg means it can operate as either ("on the go") -Required properties for dr_mode == otg: +VBUS control (required for dr_mode == otg, optional for dr_mode == host): - vbus-supply: regulator for VBUS diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 57e71f6817d0..9088ab09e200 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -53,6 +53,11 @@ OMAP DWC3 GLUE It should be set to "1" for HW mode and "2" for SW mode. - ranges: the child address space are mapped 1:1 onto the parent address space +Optional Properties: + - extcon : phandle for the extcon device omap dwc3 uses to detect + connect/disconnect events. + - vbus-supply : phandle to the regulator device tree node if needed. + Sub-nodes: The dwc3 core should be added as subnode to omap dwc3 glue. - dwc3 : diff --git a/Documentation/devicetree/bindings/usb/samsung-hsotg.txt b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt new file mode 100644 index 000000000000..b83d428a265e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt @@ -0,0 +1,40 @@ +Samsung High Speed USB OTG controller +----------------------------- + +The Samsung HSOTG IP can be found on Samsung SoCs, from S3C6400 onwards. +It gives functionality of OTG-compliant USB 2.0 host and device with +support for USB 2.0 high-speed (480Mbps) and full-speed (12 Mbps) +operation. + +Currently only device mode is supported. + +Binding details +----- + +Required properties: +- compatible: "samsung,s3c6400-hsotg" should be used for all currently + supported SoC, +- interrupt-parent: phandle for the interrupt controller to which the + interrupt signal of the HSOTG block is routed, +- interrupts: specifier of interrupt signal of interrupt controller, + according to bindings of interrupt controller, +- clocks: contains an array of clock specifiers: + - first entry: OTG clock +- clock-names: contains array of clock names: + - first entry: must be "otg" +- vusb_d-supply: phandle to voltage regulator of digital section, +- vusb_a-supply: phandle to voltage regulator of analog section. + +Example +----- + + hsotg@12480000 { + compatible = "samsung,s3c6400-hsotg"; + reg = <0x12480000 0x20000>; + interrupts = <0 71 0>; + clocks = <&clock 305>; + clock-names = "otg"; + vusb_d-supply = <&vusb_reg>; + vusb_a-supply = <&vusbdac_reg>; + }; + diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt new file mode 100644 index 000000000000..5752df0e17a2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -0,0 +1,14 @@ +USB xHCI controllers + +Required properties: + - compatible: should be "xhci-platform". + - reg: should contain address and length of the standard XHCI + register set for the device. + - interrupts: one XHCI interrupt should be described here. + +Example: + usb@f0931000 { + compatible = "xhci-platform"; + reg = <0xf0931000 0x8c8>; + interrupts = <0x0 0x4e 0x0>; + }; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index 8c5be48b43c8..a018da4a7ad7 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -1,8 +1,11 @@ SMSC USB3503 High-Speed Hub Controller Required properties: -- compatible: Should be "smsc,usb3503". -- reg: Specifies the i2c slave address, it should be 0x08. +- compatible: Should be "smsc,usb3503" or "smsc,usb3503a". + +Optional properties: +- reg: Specifies the i2c slave address, it is required and should be 0x08 + if I2C is used. - connect-gpios: Should specify GPIO for connect. - disabled-ports: Should specify the ports unused. '1' or '2' or '3' are availe for this property to describe the port diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 366ce9b87240..ec4d713674fa 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -11,6 +11,7 @@ amcc Applied Micro Circuits Corporation (APM, formally AMCC) apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. atmel Atmel Corporation +avago Avago Technologies bosch Bosch Sensortec GmbH brcm Broadcom Corporation cavium Cavium, Inc. |