diff options
Diffstat (limited to 'Documentation/networking/dsa/configuration.rst')
| -rw-r--r-- | Documentation/networking/dsa/configuration.rst | 330 |
1 files changed, 166 insertions, 164 deletions
diff --git a/Documentation/networking/dsa/configuration.rst b/Documentation/networking/dsa/configuration.rst index 11bd5e6108c0..774f0e76c746 100644 --- a/Documentation/networking/dsa/configuration.rst +++ b/Documentation/networking/dsa/configuration.rst @@ -34,8 +34,15 @@ interface. The CPU port is the switch port connected to an Ethernet MAC chip. The corresponding linux Ethernet interface is called the master interface. All other corresponding linux interfaces are called slave interfaces. -The slave interfaces depend on the master interface. They can only brought up, -when the master interface is up. +The slave interfaces depend on the master interface being up in order for them +to send or receive traffic. Prior to kernel v5.12, the state of the master +interface had to be managed explicitly by the user. Starting with kernel v5.12, +the behavior is as follows: + +- when a DSA slave interface is brought up, the master interface is + automatically brought up. +- when the master interface is brought down, all DSA slave interfaces are + automatically brought down. In this documentation the following Ethernet interfaces are used: @@ -78,79 +85,76 @@ The tagging based configuration is desired and supported by the majority of DSA switches. These switches are capable to tag incoming and outgoing traffic without using a VLAN based configuration. -single port -~~~~~~~~~~~ - -.. code-block:: sh - - # configure each interface - ip addr add 192.0.2.1/30 dev lan1 - ip addr add 192.0.2.5/30 dev lan2 - ip addr add 192.0.2.9/30 dev lan3 - - # The master interface needs to be brought up before the slave ports. - ip link set eth0 up +*single port* + .. code-block:: sh - # bring up the slave interfaces - ip link set lan1 up - ip link set lan2 up - ip link set lan3 up + # configure each interface + ip addr add 192.0.2.1/30 dev lan1 + ip addr add 192.0.2.5/30 dev lan2 + ip addr add 192.0.2.9/30 dev lan3 -bridge -~~~~~~ + # For kernels earlier than v5.12, the master interface needs to be + # brought up manually before the slave ports. + ip link set eth0 up -.. code-block:: sh + # bring up the slave interfaces + ip link set lan1 up + ip link set lan2 up + ip link set lan3 up - # The master interface needs to be brought up before the slave ports. - ip link set eth0 up +*bridge* + .. code-block:: sh - # bring up the slave interfaces - ip link set lan1 up - ip link set lan2 up - ip link set lan3 up + # For kernels earlier than v5.12, the master interface needs to be + # brought up manually before the slave ports. + ip link set eth0 up - # create bridge - ip link add name br0 type bridge + # bring up the slave interfaces + ip link set lan1 up + ip link set lan2 up + ip link set lan3 up - # add ports to bridge - ip link set dev lan1 master br0 - ip link set dev lan2 master br0 - ip link set dev lan3 master br0 + # create bridge + ip link add name br0 type bridge - # configure the bridge - ip addr add 192.0.2.129/25 dev br0 + # add ports to bridge + ip link set dev lan1 master br0 + ip link set dev lan2 master br0 + ip link set dev lan3 master br0 - # bring up the bridge - ip link set dev br0 up + # configure the bridge + ip addr add 192.0.2.129/25 dev br0 -gateway -~~~~~~~ + # bring up the bridge + ip link set dev br0 up -.. code-block:: sh +*gateway* + .. code-block:: sh - # The master interface needs to be brought up before the slave ports. - ip link set eth0 up + # For kernels earlier than v5.12, the master interface needs to be + # brought up manually before the slave ports. + ip link set eth0 up - # bring up the slave interfaces - ip link set wan up - ip link set lan1 up - ip link set lan2 up + # bring up the slave interfaces + ip link set wan up + ip link set lan1 up + ip link set lan2 up - # configure the upstream port - ip addr add 192.0.2.1/30 dev wan + # configure the upstream port + ip addr add 192.0.2.1/30 dev wan - # create bridge - ip link add name br0 type bridge + # create bridge + ip link add name br0 type bridge - # add ports to bridge - ip link set dev lan1 master br0 - ip link set dev lan2 master br0 + # add ports to bridge + ip link set dev lan1 master br0 + ip link set dev lan2 master br0 - # configure the bridge - ip addr add 192.0.2.129/25 dev br0 + # configure the bridge + ip addr add 192.0.2.129/25 dev br0 - # bring up the bridge - ip link set dev br0 up + # bring up the bridge + ip link set dev br0 up .. _dsa-vlan-configuration: @@ -161,132 +165,130 @@ A minority of switches are not capable to use a taging protocol (DSA_TAG_PROTO_NONE). These switches can be configured by a VLAN based configuration. -single port -~~~~~~~~~~~ -The configuration can only be set up via VLAN tagging and bridge setup. - -.. code-block:: sh - - # tag traffic on CPU port - ip link add link eth0 name eth0.1 type vlan id 1 - ip link add link eth0 name eth0.2 type vlan id 2 - ip link add link eth0 name eth0.3 type vlan id 3 - - # The master interface needs to be brought up before the slave ports. - ip link set eth0 up - ip link set eth0.1 up - ip link set eth0.2 up - ip link set eth0.3 up - - # bring up the slave interfaces - ip link set lan1 up - ip link set lan2 up - ip link set lan3 up - - # create bridge - ip link add name br0 type bridge - - # activate VLAN filtering - ip link set dev br0 type bridge vlan_filtering 1 - - # add ports to bridges - ip link set dev lan1 master br0 - ip link set dev lan2 master br0 - ip link set dev lan3 master br0 - - # tag traffic on ports - bridge vlan add dev lan1 vid 1 pvid untagged - bridge vlan add dev lan2 vid 2 pvid untagged - bridge vlan add dev lan3 vid 3 pvid untagged - - # configure the VLANs - ip addr add 192.0.2.1/30 dev eth0.1 - ip addr add 192.0.2.5/30 dev eth0.2 - ip addr add 192.0.2.9/30 dev eth0.3 - - # bring up the bridge devices - ip link set br0 up - +*single port* + The configuration can only be set up via VLAN tagging and bridge setup. -bridge -~~~~~~ + .. code-block:: sh -.. code-block:: sh + # tag traffic on CPU port + ip link add link eth0 name eth0.1 type vlan id 1 + ip link add link eth0 name eth0.2 type vlan id 2 + ip link add link eth0 name eth0.3 type vlan id 3 - # tag traffic on CPU port - ip link add link eth0 name eth0.1 type vlan id 1 + # For kernels earlier than v5.12, the master interface needs to be + # brought up manually before the slave ports. + ip link set eth0 up + ip link set eth0.1 up + ip link set eth0.2 up + ip link set eth0.3 up - # The master interface needs to be brought up before the slave ports. - ip link set eth0 up - ip link set eth0.1 up + # bring up the slave interfaces + ip link set lan1 up + ip link set lan2 up + ip link set lan3 up - # bring up the slave interfaces - ip link set lan1 up - ip link set lan2 up - ip link set lan3 up + # create bridge + ip link add name br0 type bridge - # create bridge - ip link add name br0 type bridge + # activate VLAN filtering + ip link set dev br0 type bridge vlan_filtering 1 - # activate VLAN filtering - ip link set dev br0 type bridge vlan_filtering 1 + # add ports to bridges + ip link set dev lan1 master br0 + ip link set dev lan2 master br0 + ip link set dev lan3 master br0 - # add ports to bridge - ip link set dev lan1 master br0 - ip link set dev lan2 master br0 - ip link set dev lan3 master br0 - ip link set eth0.1 master br0 + # tag traffic on ports + bridge vlan add dev lan1 vid 1 pvid untagged + bridge vlan add dev lan2 vid 2 pvid untagged + bridge vlan add dev lan3 vid 3 pvid untagged - # tag traffic on ports - bridge vlan add dev lan1 vid 1 pvid untagged - bridge vlan add dev lan2 vid 1 pvid untagged - bridge vlan add dev lan3 vid 1 pvid untagged + # configure the VLANs + ip addr add 192.0.2.1/30 dev eth0.1 + ip addr add 192.0.2.5/30 dev eth0.2 + ip addr add 192.0.2.9/30 dev eth0.3 - # configure the bridge - ip addr add 192.0.2.129/25 dev br0 + # bring up the bridge devices + ip link set br0 up - # bring up the bridge - ip link set dev br0 up -gateway -~~~~~~~ +*bridge* + .. code-block:: sh -.. code-block:: sh + # tag traffic on CPU port + ip link add link eth0 name eth0.1 type vlan id 1 - # tag traffic on CPU port - ip link add link eth0 name eth0.1 type vlan id 1 - ip link add link eth0 name eth0.2 type vlan id 2 + # For kernels earlier than v5.12, the master interface needs to be + # brought up manually before the slave ports. + ip link set eth0 up + ip link set eth0.1 up - # The master interface needs to be brought up before the slave ports. - ip link set eth0 up - ip link set eth0.1 up - ip link set eth0.2 up + # bring up the slave interfaces + ip link set lan1 up + ip link set lan2 up + ip link set lan3 up - # bring up the slave interfaces - ip link set wan up - ip link set lan1 up - ip link set lan2 up + # create bridge + ip link add name br0 type bridge - # create bridge - ip link add name br0 type bridge + # activate VLAN filtering + ip link set dev br0 type bridge vlan_filtering 1 - # activate VLAN filtering - ip link set dev br0 type bridge vlan_filtering 1 + # add ports to bridge + ip link set dev lan1 master br0 + ip link set dev lan2 master br0 + ip link set dev lan3 master br0 + ip link set eth0.1 master br0 - # add ports to bridges - ip link set dev wan master br0 - ip link set eth0.1 master br0 - ip link set dev lan1 master br0 - ip link set dev lan2 master br0 + # tag traffic on ports + bridge vlan add dev lan1 vid 1 pvid untagged + bridge vlan add dev lan2 vid 1 pvid untagged + bridge vlan add dev lan3 vid 1 pvid untagged - # tag traffic on ports - bridge vlan add dev lan1 vid 1 pvid untagged - bridge vlan add dev lan2 vid 1 pvid untagged - bridge vlan add dev wan vid 2 pvid untagged + # configure the bridge + ip addr add 192.0.2.129/25 dev br0 - # configure the VLANs - ip addr add 192.0.2.1/30 dev eth0.2 - ip addr add 192.0.2.129/25 dev br0 + # bring up the bridge + ip link set dev br0 up - # bring up the bridge devices - ip link set br0 up +*gateway* + .. code-block:: sh + + # tag traffic on CPU port + ip link add link eth0 name eth0.1 type vlan id 1 + ip link add link eth0 name eth0.2 type vlan id 2 + + # For kernels earlier than v5.12, the master interface needs to be + # brought up manually before the slave ports. + ip link set eth0 up + ip link set eth0.1 up + ip link set eth0.2 up + + # bring up the slave interfaces + ip link set wan up + ip link set lan1 up + ip link set lan2 up + + # create bridge + ip link add name br0 type bridge + + # activate VLAN filtering + ip link set dev br0 type bridge vlan_filtering 1 + + # add ports to bridges + ip link set dev wan master br0 + ip link set eth0.1 master br0 + ip link set dev lan1 master br0 + ip link set dev lan2 master br0 + + # tag traffic on ports + bridge vlan add dev lan1 vid 1 pvid untagged + bridge vlan add dev lan2 vid 1 pvid untagged + bridge vlan add dev wan vid 2 pvid untagged + + # configure the VLANs + ip addr add 192.0.2.1/30 dev eth0.2 + ip addr add 192.0.2.129/25 dev br0 + + # bring up the bridge devices + ip link set br0 up |