diff options
Diffstat (limited to 'Documentation')
11 files changed, 950 insertions, 143 deletions
diff --git a/Documentation/devicetree/bindings/pci/baikal,bt1-pcie.yaml b/Documentation/devicetree/bindings/pci/baikal,bt1-pcie.yaml new file mode 100644 index 000000000000..8eaa07ae9774 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/baikal,bt1-pcie.yaml @@ -0,0 +1,168 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/baikal,bt1-pcie.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Baikal-T1 PCIe Root Port Controller + +maintainers: + - Serge Semin <fancer.lancer@gmail.com> + +description: + Embedded into Baikal-T1 SoC Root Complex controller with a single port + activated. It's based on the DWC RC PCIe v4.60a IP-core, which is configured + to have just a single Root Port function and is capable of establishing the + link up to Gen.3 speed on x4 lanes. It doesn't have embedded clock and reset + control module, so the proper interface initialization is supposed to be + performed by software. There four in- and four outbound iATU regions + which can be used to emit all required TLP types on the PCIe bus. + +allOf: + - $ref: /schemas/pci/snps,dw-pcie.yaml# + +properties: + compatible: + const: baikal,bt1-pcie + + reg: + description: + DBI, DBI2 and at least 4KB outbound iATU-capable region for the + peripheral devices CFG-space access. + maxItems: 3 + + reg-names: + items: + - const: dbi + - const: dbi2 + - const: config + + interrupts: + description: + MSI, AER, PME, Hot-plug, Link Bandwidth Management, Link Equalization + request and eight Read/Write eDMA IRQ lines are available. + maxItems: 14 + + interrupt-names: + items: + - const: dma0 + - const: dma1 + - const: dma2 + - const: dma3 + - const: dma4 + - const: dma5 + - const: dma6 + - const: dma7 + - const: msi + - const: aer + - const: pme + - const: hp + - const: bw_mg + - const: l_eq + + clocks: + description: + DBI (attached to the APB bus), AXI-bus master and slave interfaces + are fed up by the dedicated application clocks. A common reference + clock signal is supposed to be attached to the corresponding Ref-pad + of the SoC. It will be redistributed amongst the controller core + sub-modules (pipe, core, aux, etc). + maxItems: 4 + + clock-names: + items: + - const: dbi + - const: mstr + - const: slv + - const: ref + + resets: + description: + A comprehensive controller reset logic is supposed to be implemented + by software, so almost all the possible application and core reset + signals are exposed via the system CCU module. + maxItems: 9 + + reset-names: + items: + - const: mstr + - const: slv + - const: pwr + - const: hot + - const: phy + - const: core + - const: pipe + - const: sticky + - const: non-sticky + + baikal,bt1-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the Baikal-T1 System Controller DT node. It's required to + access some additional PM, Reset-related and LTSSM signals. + + num-lanes: + maximum: 4 + + max-link-speed: + maximum: 3 + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/gpio/gpio.h> + + pcie@1f052000 { + compatible = "baikal,bt1-pcie"; + device_type = "pci"; + reg = <0x1f052000 0x1000>, <0x1f053000 0x1000>, <0x1bdbf000 0x1000>; + reg-names = "dbi", "dbi2", "config"; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x81000000 0 0x00000000 0x1bdb0000 0 0x00008000>, + <0x82000000 0 0x20000000 0x08000000 0 0x13db0000>; + bus-range = <0x0 0xff>; + + interrupts = <GIC_SHARED 80 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 81 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 82 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 83 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 84 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 85 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 86 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 88 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 89 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 90 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 91 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 92 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 93 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "dma0", "dma1", "dma2", "dma3", + "dma4", "dma5", "dma6", "dma7", + "msi", "aer", "pme", "hp", "bw_mg", + "l_eq"; + + clocks = <&ccu_sys 1>, <&ccu_axi 6>, <&ccu_axi 7>, <&clk_pcie>; + clock-names = "dbi", "mstr", "slv", "ref"; + + resets = <&ccu_axi 6>, <&ccu_axi 7>, <&ccu_sys 7>, <&ccu_sys 10>, + <&ccu_sys 4>, <&ccu_sys 6>, <&ccu_sys 5>, <&ccu_sys 8>, + <&ccu_sys 9>; + reset-names = "mstr", "slv", "pwr", "hot", "phy", "core", "pipe", + "sticky", "non-sticky"; + + reset-gpios = <&port0 0 GPIO_ACTIVE_LOW>; + + num-lanes = <4>; + max-link-speed = <3>; + }; +... diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml index 376e739bcad4..49b4f7a32e71 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml @@ -14,9 +14,6 @@ description: |+ This PCIe host controller is based on the Synopsys DesignWare PCIe IP and thus inherits all the common properties defined in snps,dw-pcie.yaml. -allOf: - - $ref: /schemas/pci/snps,dw-pcie.yaml# - properties: compatible: enum: @@ -61,7 +58,7 @@ properties: - const: pcie - const: pcie_bus - const: pcie_phy - - const: pcie_inbound_axi for imx6sx-pcie, pcie_aux for imx8mq-pcie + - enum: [ pcie_inbound_axi, pcie_aux ] num-lanes: const: 1 @@ -175,6 +172,47 @@ required: - clocks - clock-names +allOf: + - $ref: /schemas/pci/snps,dw-pcie.yaml# + - if: + properties: + compatible: + contains: + const: fsl,imx6sx-pcie + then: + properties: + clock-names: + items: + - {} + - {} + - {} + - const: pcie_inbound_axi + - if: + properties: + compatible: + contains: + const: fsl,imx8mq-pcie + then: + properties: + clock-names: + items: + - {} + - {} + - {} + - const: pcie_aux + - if: + properties: + compatible: + not: + contains: + enum: + - fsl,imx6sx-pcie + - fsl,imx8mq-pcie + then: + properties: + clock-names: + maxItems: 3 + unevaluatedProperties: false examples: diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml index c00be39af64e..7e8c7a2a5f9b 100644 --- a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml @@ -43,14 +43,12 @@ description: |+ each set has its own address for MSI message, and supports 32 MSI vectors to generate interrupt. -allOf: - - $ref: /schemas/pci/pci-bus.yaml# - properties: compatible: oneOf: - items: - enum: + - mediatek,mt7986-pcie - mediatek,mt8188-pcie - mediatek,mt8195-pcie - const: mediatek,mt8192-pcie @@ -70,29 +68,29 @@ properties: minItems: 1 maxItems: 8 + iommu-map: + maxItems: 1 + + iommu-map-mask: + const: 0 + resets: minItems: 1 maxItems: 2 reset-names: minItems: 1 + maxItems: 2 items: - - const: phy - - const: mac + enum: [ phy, mac ] clocks: + minItems: 4 maxItems: 6 clock-names: - items: - - const: pl_250m - - const: tl_26m - - const: tl_96m - - const: tl_32k - - const: peri_26m - - enum: - - top_133m # for MT8192 - - peri_mem # for MT8188/MT8195 + minItems: 4 + maxItems: 6 assigned-clocks: maxItems: 1 @@ -107,6 +105,9 @@ properties: items: - const: pcie-phy + power-domains: + maxItems: 1 + '#interrupt-cells': const: 1 @@ -138,6 +139,54 @@ required: - '#interrupt-cells' - interrupt-controller +allOf: + - $ref: /schemas/pci/pci-bus.yaml# + - if: + properties: + compatible: + const: mediatek,mt8192-pcie + then: + properties: + clock-names: + items: + - const: pl_250m + - const: tl_26m + - const: tl_96m + - const: tl_32k + - const: peri_26m + - const: top_133m + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8188-pcie + - mediatek,mt8195-pcie + then: + properties: + clock-names: + items: + - const: pl_250m + - const: tl_26m + - const: tl_96m + - const: tl_32k + - const: peri_26m + - const: peri_mem + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt7986-pcie + then: + properties: + clock-names: + items: + - const: pl_250m + - const: tl_26m + - const: peri_26m + - const: top_133m + unevaluatedProperties: false examples: diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml index 54f07852d279..a5859bb3dc28 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml @@ -62,6 +62,16 @@ properties: minItems: 3 maxItems: 13 + dma-coherent: true + + interconnects: + maxItems: 2 + + interconnect-names: + items: + - const: pcie-mem + - const: cpu-pcie + resets: minItems: 1 maxItems: 12 @@ -632,6 +642,18 @@ allOf: - const: pci # PCIe core reset - if: + properties: + compatible: + contains: + enum: + - qcom,pcie-sa8540p + - qcom,pcie-sc8280xp + then: + required: + - interconnects + - interconnect-names + + - if: not: properties: compatible: diff --git a/Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml b/Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml index bc0a9d1db750..2be72ae1169f 100644 --- a/Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml +++ b/Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml @@ -14,10 +14,10 @@ maintainers: description: |+ RK3568 SoC PCIe host controller is based on the Synopsys DesignWare PCIe IP and thus inherits all the common properties defined in - designware-pcie.txt. + snps,dw-pcie.yaml. allOf: - - $ref: /schemas/pci/pci-bus.yaml# + - $ref: /schemas/pci/snps,dw-pcie.yaml# properties: compatible: diff --git a/Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml b/Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml new file mode 100644 index 000000000000..d87e13496834 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml @@ -0,0 +1,266 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/snps,dw-pcie-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DWC PCIe RP/EP controller + +maintainers: + - Jingoo Han <jingoohan1@gmail.com> + - Gustavo Pimentel <gustavo.pimentel@synopsys.com> + +description: + Generic Synopsys DesignWare PCIe Root Port and Endpoint controller + properties. + +select: false + +properties: + reg: + description: + DWC PCIe CSR space is normally accessed over the dedicated Data Bus + Interface - DBI. In accordance with the reference manual the register + configuration space belongs to the Configuration-Dependent Module (CDM) + and is split up into several sub-parts Standard PCIe configuration + space, Port Logic Registers (PL), Shadow Config-space Registers, + iATU/eDMA registers. The particular sub-space is selected by the + CDM/ELBI (dbi_cs) and CS2 (dbi_cs2) signals (selector bits). Such + configuration provides a flexible interface for the system engineers to + either map the particular space at a desired MMIO address or just leave + them in a contiguous memory space if pure Native or AXI Bridge DBI access + is selected. Note the PCIe CFG-space, PL and Shadow registers are + specific for each activated function, while the rest of the sub-spaces + are common for all of them (if there are more than one). + minItems: 2 + maxItems: 6 + + reg-names: + minItems: 2 + maxItems: 6 + + interrupts: + description: + There are two main sub-blocks which are normally capable of + generating interrupts. It's System Information Interface and MSI + interface. While the former one has some common for the Host and + Endpoint controllers IRQ-signals, the later interface is obviously + Root Complex specific since it's responsible for the incoming MSI + messages signalling. The System Information IRQ signals are mainly + responsible for reporting the generic PCIe hierarchy and Root + Complex events like VPD IO request, general AER, PME, Hot-plug, link + bandwidth change, link equalization request, INTx asserted/deasserted + Message detection, embedded DMA Tx/Rx/Error. + minItems: 1 + maxItems: 26 + + interrupt-names: + minItems: 1 + maxItems: 26 + + clocks: + description: + DWC PCIe reference manual explicitly defines a set of the clocks required + to get the controller working correctly. In general all of them can + be divided into two groups':' application and core clocks. Note the + platforms may have some of the clock sources unspecified in case if the + corresponding domains are fed up from a common clock source. + minItems: 1 + maxItems: 7 + + clock-names: + minItems: 1 + maxItems: 7 + items: + oneOf: + - description: + Data Bus Interface (DBI) clock. Clock signal for the AXI-bus + interface of the Configuration-Dependent Module, which is + basically the set of the controller CSRs. + const: dbi + - description: + Application AXI-bus Master interface clock. Basically this is + a clock for the controller DMA interface (PCI-to-CPU). + const: mstr + - description: + Application AXI-bus Slave interface clock. This is a clock for + the CPU-to-PCI memory IO interface. + const: slv + - description: + Controller Core-PCS PIPE interface clock. It's normally + supplied by an external PCS-PHY. + const: pipe + - description: + Controller Primary clock. It's assumed that all controller input + signals (except resets) are synchronous to this clock. + const: core + - description: + Auxiliary clock for the controller PMC domain. The controller + partitioning implies having some parts to operate with this + clock in some power management states. + const: aux + - description: + Generic reference clock. In case if there are several + interfaces fed up with a common clock source it's advisable to + define it with this name (for instance pipe, core and aux can + be connected to a single source of the periodic signal). + const: ref + - description: + Clock for the PHY registers interface. Originally this is + a PHY-viewport-based interface, but some platform may have + specifically designed one. + const: phy_reg + - description: + Vendor-specific clock names. Consider using the generic names + above for new bindings. + oneOf: + - description: See native 'dbi' clock for details + enum: [ pcie, pcie_apb_sys, aclk_dbi ] + - description: See native 'mstr/slv' clock for details + enum: [ pcie_bus, pcie_inbound_axi, pcie_aclk, aclk_mst, aclk_slv ] + - description: See native 'pipe' clock for details + enum: [ pcie_phy, pcie_phy_ref, link ] + - description: See native 'aux' clock for details + enum: [ pcie_aux ] + - description: See native 'ref' clock for details. + enum: [ gio ] + - description: See nativs 'phy_reg' clock for details + enum: [ pcie_apb_phy, pclk ] + + resets: + description: + DWC PCIe reference manual explicitly defines a set of the reset + signals required to be de-asserted to properly activate the controller + sub-parts. All of these signals can be divided into two sub-groups':' + application and core resets with respect to the main sub-domains they + are supposed to reset. Note the platforms may have some of these signals + unspecified in case if they are automatically handled or aggregated into + a comprehensive control module. + minItems: 1 + maxItems: 10 + + reset-names: + minItems: 1 + maxItems: 10 + items: + oneOf: + - description: Data Bus Interface (DBI) domain reset + const: dbi + - description: AXI-bus Master interface reset + const: mstr + - description: AXI-bus Slave interface reset + const: slv + - description: Application-dependent interface reset + const: app + - description: Controller Non-sticky CSR flags reset + const: non-sticky + - description: Controller sticky CSR flags reset + const: sticky + - description: PIPE-interface (Core-PCS) logic reset + const: pipe + - description: + Controller primary reset (resets everything except PMC module) + const: core + - description: PCS/PHY block reset + const: phy + - description: PMC hot reset signal + const: hot + - description: Cold reset signal + const: pwr + - description: + Vendor-specific reset names. Consider using the generic names + above for new bindings. + oneOf: + - description: See native 'app' reset for details + enum: [ apps, gio, apb ] + - description: See native 'phy' reset for details + enum: [ pciephy, link ] + - description: See native 'pwr' reset for details + enum: [ turnoff ] + + phys: + description: + There can be up to the number of possible lanes PHYs specified placed in + the phandle array in the line-based order. Obviously each the specified + PHYs are supposed to be able to work in the PCIe mode with a speed + implied by the DWC PCIe controller they are attached to. + minItems: 1 + maxItems: 16 + + phy-names: + minItems: 1 + maxItems: 16 + oneOf: + - description: Generic PHY names + items: + pattern: '^pcie[0-9]+$' + - description: + Vendor-specific PHY names. Consider using the generic + names above for new bindings. + items: + oneOf: + - pattern: '^pcie(-?phy[0-9]*)?$' + - pattern: '^p2u-[0-7]$' + + reset-gpio: + deprecated: true + description: + Reference to the GPIO-controlled PERST# signal. It is used to reset all + the peripheral devices available on the PCIe bus. + maxItems: 1 + + reset-gpios: + description: + Reference to the GPIO-controlled PERST# signal. It is used to reset all + the peripheral devices available on the PCIe bus. + maxItems: 1 + + max-link-speed: + maximum: 5 + + num-lanes: + description: + Number of PCIe link lanes to use. Can be omitted if the already brought + up link is supposed to be preserved. + maximum: 16 + + num-ob-windows: + $ref: /schemas/types.yaml#/definitions/uint32 + deprecated: true + description: + Number of outbound address translation windows. This parameter can be + auto-detected based on the iATU memory writability. So there is no + point in having a dedicated DT-property for it. + maximum: 256 + + num-ib-windows: + $ref: /schemas/types.yaml#/definitions/uint32 + deprecated: true + description: + Number of inbound address translation windows. In the same way as + for the outbound AT windows, this parameter can be auto-detected based + on the iATU memory writability. There is no point having a dedicated + DT-property for it either. + maximum: 256 + + num-viewport: + $ref: /schemas/types.yaml#/definitions/uint32 + deprecated: true + description: + Number of outbound view ports configured in hardware. It's the same as + the number of outbound AT windows. + maximum: 256 + + snps,enable-cdm-check: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enable automatic checking of CDM (Configuration Dependent Module) + registers for data corruption. CDM registers include standard PCIe + configuration space registers, Port Logic registers, DMA and iATU + registers. This feature has been available since DWC PCIe v4.80a. + + dma-coherent: true + +additionalProperties: true + +... diff --git a/Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml index b78535040f04..8fc2151691a4 100644 --- a/Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml +++ b/Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml @@ -13,76 +13,182 @@ maintainers: description: | Synopsys DesignWare PCIe host controller endpoint +# Please create a separate DT-schema for your DWC PCIe Endpoint controller +# and make sure it's assigned with the vendor-specific compatible string. +select: + properties: + compatible: + const: snps,dw-pcie-ep + required: + - compatible + allOf: - $ref: /schemas/pci/pci-ep.yaml# + - $ref: /schemas/pci/snps,dw-pcie-common.yaml# properties: - compatible: - anyOf: - - {} - - const: snps,dw-pcie-ep - reg: - description: | - It should contain Data Bus Interface (dbi) and config registers for all - versions. - For designware core version >= 4.80, it may contain ATU address space. + description: + DBI, DBI2 reg-spaces and outbound memory window are required for the + normal controller functioning. iATU memory IO region is also required + if the space is unrolled (IP-core version >= 4.80a). minItems: 2 - maxItems: 4 + maxItems: 5 reg-names: minItems: 2 - maxItems: 4 + maxItems: 5 items: - enum: [dbi, dbi2, config, atu, addr_space, link, atu_dma, appl] - - reset-gpio: - description: GPIO pin number of PERST# signal - maxItems: 1 - deprecated: true - - reset-gpios: - description: GPIO controlled connection to PERST# signal - maxItems: 1 - - snps,enable-cdm-check: - type: boolean - description: | - This is a boolean property and if present enables - automatic checking of CDM (Configuration Dependent Module) registers - for data corruption. CDM registers include standard PCIe configuration - space registers, Port Logic registers, DMA and iATU (internal Address - Translation Unit) registers. - - num-ib-windows: - $ref: /schemas/types.yaml#/definitions/uint32 - maximum: 256 - description: number of inbound address translation windows - deprecated: true - - num-ob-windows: - $ref: /schemas/types.yaml#/definitions/uint32 - maximum: 256 - description: number of outbound address translation windows - deprecated: true + oneOf: + - description: + Basic DWC PCIe controller configuration-space accessible over + the DBI interface. This memory space is either activated with + CDM/ELBI = 0 and CS2 = 0 or is a contiguous memory region + with all spaces. Note iATU/eDMA CSRs are indirectly accessible + via the PL viewports on the DWC PCIe controllers older than + v4.80a. + const: dbi + - description: + Shadow DWC PCIe config-space registers. This space is selected + by setting CDM/ELBI = 0 and CS2 = 1. This is an intermix of + the PCI-SIG PCIe CFG-space with the shadow registers for some + PCI Header space, PCI Standard and Extended Structures. It's + mainly relevant for the end-point controller configuration, + but still there are some shadow registers available for the + Root Port mode too. + const: dbi2 + - description: + External Local Bus registers. It's an application-dependent + registers normally defined by the platform engineers. The space + can be selected by setting CDM/ELBI = 1 and CS2 = 0 wires or can + be accessed over some platform-specific means (for instance + as a part of a system controller). + enum: [ elbi, app ] + - description: + iATU/eDMA registers common for all device functions. It's an + unrolled memory space with the internal Address Translation + Unit and Enhanced DMA, which is selected by setting CDM/ELBI = 1 + and CS2 = 1. For IP-core releases prior v4.80a, these registers + have been programmed via an indirect addressing scheme using a + set of viewport CSRs mapped into the PL space. Note iATU is + normally mapped to the 0x0 address of this region, while eDMA + is available at 0x80000 base address. + const: atu + - description: + Platform-specific eDMA registers. Some platforms may have eDMA + CSRs mapped in a non-standard base address. The registers offset + can be changed or the MS/LS-bits of the address can be attached + in an additional RTL block before the MEM-IO transactions reach + the DW PCIe slave interface. + const: dma + - description: + PHY/PCS configuration registers. Some platforms can have the + PCS and PHY CSRs accessible over a dedicated memory mapped + region, but mainly these registers are indirectly accessible + either by means of the embedded PHY viewport schema or by some + platform-specific method. + const: phy + - description: + Outbound iATU-capable memory-region which will be used to + generate various application-specific traffic on the PCIe bus + hierarchy. It's usage scenario depends on the endpoint + functionality, for instance it can be used to create MSI(X) + messages. + const: addr_space + - description: + Vendor-specific CSR names. Consider using the generic names above + for new bindings. + oneOf: + - description: See native 'elbi/app' CSR region for details. + enum: [ link, appl ] + - description: See native 'atu' CSR region for details. + enum: [ atu_dma ] + allOf: + - contains: + const: dbi + - contains: + const: addr_space + + interrupts: + description: + There is no mandatory IRQ signals for the normal controller functioning, + but in addition to the native set the platforms may have a link- or + PM-related IRQs specified. + minItems: 1 + maxItems: 20 + + interrupt-names: + minItems: 1 + maxItems: 20 + items: + oneOf: + - description: + Controller request to read or write virtual product data + from/to the VPD capability registers. + const: vpd + - description: + Link Equalization Request flag is set in the Link Status 2 + register (applicable if the corresponding IRQ is enabled in + the Link Control 3 register). + const: l_eq + - description: + Indicates that the eDMA Tx/Rx transfer is complete or that an + error has occurred on the corresponding channel. eDMA can have + eight Tx (Write) and Rx (Read) eDMA channels thus supporting up + to 16 IRQ signals all together. Write eDMA channels shall go + first in the ordered row as per default edma_int[*] bus setup. + pattern: '^dma([0-9]|1[0-5])?$' + - description: + PCIe protocol correctable error or a Data Path protection + correctable error is detected by the automotive/safety + feature. + const: sft_ce + - description: + Indicates that the internal safety mechanism has detected an + uncorrectable error. + const: sft_ue + - description: + Application-specific IRQ raised depending on the vendor-specific + events basis. + const: app + - description: + Vendor-specific IRQ names. Consider using the generic names above + for new bindings. + oneOf: + - description: See native "app" IRQ for details + enum: [ intr ] + + max-functions: + maximum: 32 required: + - compatible - reg - reg-names - - compatible additionalProperties: true examples: - | - bus { - #address-cells = <1>; - #size-cells = <1>; - pcie-ep@dfd00000 { - compatible = "snps,dw-pcie-ep"; - reg = <0xdfc00000 0x0001000>, /* IP registers 1 */ - <0xdfc01000 0x0001000>, /* IP registers 2 */ - <0xd0000000 0x2000000>; /* Configuration space */ - reg-names = "dbi", "dbi2", "addr_space"; - }; + pcie-ep@dfd00000 { + compatible = "snps,dw-pcie-ep"; + reg = <0xdfc00000 0x0001000>, /* IP registers 1 */ + <0xdfc01000 0x0001000>, /* IP registers 2 */ + <0xd0000000 0x2000000>; /* Configuration space */ + reg-names = "dbi", "dbi2", "addr_space"; + + interrupts = <23>, <24>; + interrupt-names = "dma0", "dma1"; + + clocks = <&sys_clk 12>, <&sys_clk 24>; + clock-names = "dbi", "ref"; + + resets = <&sys_rst 12>, <&sys_rst 24>; + reset-names = "dbi", "phy"; + + phys = <&pcie_phy0>, <&pcie_phy1>, <&pcie_phy2>, <&pcie_phy3>; + phy-names = "pcie0", "pcie1", "pcie2", "pcie3"; + + max-link-speed = <3>; + max-functions = /bits/ 8 <4>; }; diff --git a/Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml b/Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml index 7e0b015f1414..1a83f0f65f19 100644 --- a/Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml +++ b/Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml @@ -13,20 +13,25 @@ maintainers: description: | Synopsys DesignWare PCIe host controller +# Please create a separate DT-schema for your DWC PCIe Root Port controller +# and make sure it's assigned with the vendor-specific compatible string. +select: + properties: + compatible: + const: snps,dw-pcie + required: + - compatible + allOf: - $ref: /schemas/pci/pci-bus.yaml# + - $ref: /schemas/pci/snps,dw-pcie-common.yaml# properties: - compatible: - anyOf: - - {} - - const: snps,dw-pcie - reg: - description: | - It should contain Data Bus Interface (dbi) and config registers for all - versions. - For designware core version >= 4.80, it may contain ATU address space. + description: + At least DBI reg-space and peripheral devices CFG-space outbound window + are required for the normal controller work. iATU memory IO region is + also required if the space is unrolled (IP-core version >= 4.80a). minItems: 2 maxItems: 5 @@ -34,71 +39,194 @@ properties: minItems: 2 maxItems: 5 items: - enum: [ dbi, dbi2, config, atu, atu_dma, app, appl, elbi, mgmt, ctrl, - parf, cfg, link, ulreg, smu, mpu, apb, phy, ecam ] - - num-lanes: - description: | - number of lanes to use (this property should be specified unless - the link is brought already up in firmware) - maximum: 16 - - reset-gpio: - description: GPIO pin number of PERST# signal - maxItems: 1 - deprecated: true - - reset-gpios: - description: GPIO controlled connection to PERST# signal - maxItems: 1 - - interrupts: true - - interrupt-names: true - - clocks: true - - snps,enable-cdm-check: - type: boolean - description: | - This is a boolean property and if present enables - automatic checking of CDM (Configuration Dependent Module) registers - for data corruption. CDM registers include standard PCIe configuration - space registers, Port Logic registers, DMA and iATU (internal Address - Translation Unit) registers. - - num-viewport: - $ref: /schemas/types.yaml#/definitions/uint32 - maximum: 256 - description: | - number of view ports configured in hardware. If a platform - does not specify it, the driver autodetects it. - deprecated: true + oneOf: + - description: + Basic DWC PCIe controller configuration-space accessible over + the DBI interface. This memory space is either activated with + CDM/ELBI = 0 and CS2 = 0 or is a contiguous memory region + with all spaces. Note iATU/eDMA CSRs are indirectly accessible + via the PL viewports on the DWC PCIe controllers older than + v4.80a. + const: dbi + - description: + Shadow DWC PCIe config-space registers. This space is selected + by setting CDM/ELBI = 0 and CS2 = 1. This is an intermix of + the PCI-SIG PCIe CFG-space with the shadow registers for some + PCI Header space, PCI Standard and Extended Structures. It's + mainly relevant for the end-point controller configuration, + but still there are some shadow registers available for the + Root Port mode too. + const: dbi2 + - description: + External Local Bus registers. It's an application-dependent + registers normally defined by the platform engineers. The space + can be selected by setting CDM/ELBI = 1 and CS2 = 0 wires or can + be accessed over some platform-specific means (for instance + as a part of a system controller). + enum: [ elbi, app ] + - description: + iATU/eDMA registers common for all device functions. It's an + unrolled memory space with the internal Address Translation + Unit and Enhanced DMA, which is selected by setting CDM/ELBI = 1 + and CS2 = 1. For IP-core releases prior v4.80a, these registers + have been programmed via an indirect addressing scheme using a + set of viewport CSRs mapped into the PL space. Note iATU is + normally mapped to the 0x0 address of this region, while eDMA + is available at 0x80000 base address. + const: atu + - description: + Platform-specific eDMA registers. Some platforms may have eDMA + CSRs mapped in a non-standard base address. The registers offset + can be changed or the MS/LS-bits of the address can be attached + in an additional RTL block before the MEM-IO transactions reach + the DW PCIe slave interface. + const: dma + - description: + PHY/PCS configuration registers. Some platforms can have the + PCS and PHY CSRs accessible over a dedicated memory mapped + region, but mainly these registers are indirectly accessible + either by means of the embedded PHY viewport schema or by some + platform-specific method. + const: phy + - description: + Outbound iATU-capable memory-region which will be used to access + the peripheral PCIe devices configuration space. + const: config + - description: + Vendor-specific CSR names. Consider using the generic names above + for new bindings. + oneOf: + - description: See native 'elbi/app' CSR region for details. + enum: [ apb, mgmt, link, ulreg, appl ] + - description: See native 'atu' CSR region for details. + enum: [ atu_dma ] + - description: Syscon-related CSR regions. + enum: [ smu, mpu ] + - description: Tegra234 aperture + enum: [ ecam ] + allOf: + - contains: + const: dbi + - contains: + const: config + + interrupts: + description: + DWC PCIe Root Port/Complex specific IRQ signals. At least MSI interrupt + signal is supposed to be specified for the host controller. + minItems: 1 + maxItems: 26 + + interrupt-names: + minItems: 1 + maxItems: 26 + items: + oneOf: + - description: + Controller request to read or write virtual product data + from/to the VPD capability registers. + const: vpd + - description: + Link Equalization Request flag is set in the Link Status 2 + register (applicable if the corresponding IRQ is enabled in + the Link Control 3 register). + const: l_eq + - description: + Indicates that the eDMA Tx/Rx transfer is complete or that an + error has occurred on the corresponding channel. eDMA can have + eight Tx (Write) and Rx (Read) eDMA channels thus supporting up + to 16 IRQ signals all together. Write eDMA channels shall go + first in the ordered row as per default edma_int[*] bus setup. + pattern: '^dma([0-9]|1[0-5])?$' + - description: + PCIe protocol correctable error or a Data Path protection + correctable error is detected by the automotive/safety + feature. + const: sft_ce + - description: + Indicates that the internal safety mechanism has detected an + uncorrectable error. + const: sft_ue + - description: + Application-specific IRQ raised depending on the vendor-specific + events basis. + const: app + - description: + DSP AXI MSI Interrupt detected. It gets de-asserted when there is + no more MSI interrupt pending. The interrupt is relevant to the + iMSI-RX - Integrated MSI Receiver (AXI bridge). + const: msi + - description: + Legacy A/B/C/D interrupt signal. Basically it's triggered by + receiving a Assert_INT{A,B,C,D}/Desassert_INT{A,B,C,D} message + from the downstream device. + pattern: "^int(a|b|c|d)$" + - description: + Error condition detected and a flag is set in the Root Error Status + register of the AER capability. It's asserted when the RC + internally generated an error or an error message is received by + the RC. + const: aer + - description: + PME message is received by the port. That means having the PME + status bit set in the Root Status register (the event is + supposed to be unmasked in the Root Control register). + const: pme + - description: + Hot-plug event is detected. That is a bit has been set in the + Slot Status register and the corresponding event is enabled in + the Slot Control register. + const: hp + - description: + Link Autonomous Bandwidth Status flag has been set in the Link + Status register (the event is supposed to be unmasked in the + Link Control register). + const: bw_au + - description: + Bandwidth Management Status flag has been set in the Link + Status register (the event is supposed to be unmasked in the + Link Control register). + const: bw_mg + - description: + Vendor-specific IRQ names. Consider using the generic names above + for new bindings. + oneOf: + - description: See native "app" IRQ for details + enum: [ intr ] + allOf: + - contains: + const: msi additionalProperties: true required: + - compatible - reg - reg-names - - compatible examples: - | - bus { - #address-cells = <1>; - #size-cells = <1>; - pcie@dfc00000 { - device_type = "pci"; - compatible = "snps,dw-pcie"; - reg = <0xdfc00000 0x0001000>, /* IP registers */ - <0xd0000000 0x0002000>; /* Configuration space */ - reg-names = "dbi", "config"; - #address-cells = <3>; - #size-cells = <2>; - ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000>, - <0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>; - interrupts = <25>, <24>; - #interrupt-cells = <1>; - num-lanes = <1>; - }; + pcie@dfc00000 { + compatible = "snps,dw-pcie"; + device_type = "pci"; + reg = <0xdfc00000 0x0001000>, /* IP registers */ + <0xd0000000 0x0002000>; /* Configuration space */ + reg-names = "dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000>, + <0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>; + bus-range = <0x0 0xff>; + + interrupts = <25>, <24>; + interrupt-names = "msi", "hp"; + #interrupt-cells = <1>; + + reset-gpios = <&port0 0 1>; + + phys = <&pcie_phy>; + phy-names = "pcie"; + + num-lanes = <1>; + max-link-speed = <3>; }; diff --git a/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml b/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml index aed437dac363..10e6eabdff53 100644 --- a/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml +++ b/Documentation/devicetree/bindings/pci/ti,j721e-pci-ep.yaml @@ -58,6 +58,13 @@ properties: dma-coherent: description: Indicates that the PCIe IP block can ensure the coherency + interrupts: + maxItems: 1 + + interrupt-names: + items: + - const: link_state + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml b/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml index 2115d5a3f0e1..b0513b197d08 100644 --- a/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml +++ b/Documentation/devicetree/bindings/pci/ti,j721e-pci-host.yaml @@ -73,9 +73,31 @@ properties: - const: 0xb00f - items: - const: 0xb010 + - items: + - const: 0xb013 msi-map: true + interrupts: + maxItems: 1 + + interrupt-names: + items: + - const: link_state + + interrupt-controller: + type: object + additionalProperties: false + + properties: + interrupt-controller: true + + '#interrupt-cells': + const: 1 + + interrupts: + maxItems: 1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml index 48ed227fc5b9..53da2edd7c9a 100644 --- a/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml +++ b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml @@ -36,7 +36,7 @@ properties: - const: mpu interrupts: - maxItems: 1 + maxItems: 2 clocks: items: @@ -94,8 +94,9 @@ examples: #interrupt-cells = <1>; ranges = <0x81000000 0 0x40000000 0 0x40000000 0 0x00010000>, <0x82000000 0 0x50000000 0 0x50000000 0 0x20000000>; - interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "intr"; + interrupts = <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi", "intr"; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH |