diff options
Diffstat (limited to 'drivers/net/dsa/sja1105/sja1105_main.c')
| -rw-r--r-- | drivers/net/dsa/sja1105/sja1105_main.c | 1675 |
1 files changed, 1675 insertions, 0 deletions
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c new file mode 100644 index 000000000000..50ff625c85d6 --- /dev/null +++ b/drivers/net/dsa/sja1105/sja1105_main.c @@ -0,0 +1,1675 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2018, Sensor-Technik Wiedemann GmbH + * Copyright (c) 2018-2019, Vladimir Oltean <olteanv@gmail.com> + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/printk.h> +#include <linux/spi/spi.h> +#include <linux/errno.h> +#include <linux/gpio/consumer.h> +#include <linux/phylink.h> +#include <linux/of.h> +#include <linux/of_net.h> +#include <linux/of_mdio.h> +#include <linux/of_device.h> +#include <linux/netdev_features.h> +#include <linux/netdevice.h> +#include <linux/if_bridge.h> +#include <linux/if_ether.h> +#include <linux/dsa/8021q.h> +#include "sja1105.h" + +static void sja1105_hw_reset(struct gpio_desc *gpio, unsigned int pulse_len, + unsigned int startup_delay) +{ + gpiod_set_value_cansleep(gpio, 1); + /* Wait for minimum reset pulse length */ + msleep(pulse_len); + gpiod_set_value_cansleep(gpio, 0); + /* Wait until chip is ready after reset */ + msleep(startup_delay); +} + +static void +sja1105_port_allow_traffic(struct sja1105_l2_forwarding_entry *l2_fwd, + int from, int to, bool allow) +{ + if (allow) { + l2_fwd[from].bc_domain |= BIT(to); + l2_fwd[from].reach_port |= BIT(to); + l2_fwd[from].fl_domain |= BIT(to); + } else { + l2_fwd[from].bc_domain &= ~BIT(to); + l2_fwd[from].reach_port &= ~BIT(to); + l2_fwd[from].fl_domain &= ~BIT(to); + } +} + +/* Structure used to temporarily transport device tree + * settings into sja1105_setup + */ +struct sja1105_dt_port { + phy_interface_t phy_mode; + sja1105_mii_role_t role; +}; + +static int sja1105_init_mac_settings(struct sja1105_private *priv) +{ + struct sja1105_mac_config_entry default_mac = { + /* Enable all 8 priority queues on egress. + * Every queue i holds top[i] - base[i] frames. + * Sum of top[i] - base[i] is 511 (max hardware limit). + */ + .top = {0x3F, 0x7F, 0xBF, 0xFF, 0x13F, 0x17F, 0x1BF, 0x1FF}, + .base = {0x0, 0x40, 0x80, 0xC0, 0x100, 0x140, 0x180, 0x1C0}, + .enabled = {true, true, true, true, true, true, true, true}, + /* Keep standard IFG of 12 bytes on egress. */ + .ifg = 0, + /* Always put the MAC speed in automatic mode, where it can be + * retrieved from the PHY object through phylib and + * sja1105_adjust_port_config. + */ + .speed = SJA1105_SPEED_AUTO, + /* No static correction for 1-step 1588 events */ + .tp_delin = 0, + .tp_delout = 0, + /* Disable aging for critical TTEthernet traffic */ + .maxage = 0xFF, + /* Internal VLAN (pvid) to apply to untagged ingress */ + .vlanprio = 0, + .vlanid = 0, + .ing_mirr = false, + .egr_mirr = false, + /* Don't drop traffic with other EtherType than ETH_P_IP */ + .drpnona664 = false, + /* Don't drop double-tagged traffic */ + .drpdtag = false, + /* Don't drop untagged traffic */ + .drpuntag = false, + /* Don't retag 802.1p (VID 0) traffic with the pvid */ + .retag = false, + /* Disable learning and I/O on user ports by default - + * STP will enable it. + */ + .dyn_learn = false, + .egress = false, + .ingress = false, + }; + struct sja1105_mac_config_entry *mac; + struct sja1105_table *table; + int i; + + table = &priv->static_config.tables[BLK_IDX_MAC_CONFIG]; + + /* Discard previous MAC Configuration Table */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_NUM_PORTS, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + /* Override table based on phylib DT bindings */ + table->entry_count = SJA1105_NUM_PORTS; + + mac = table->entries; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + mac[i] = default_mac; + if (i == dsa_upstream_port(priv->ds, i)) { + /* STP doesn't get called for CPU port, so we need to + * set the I/O parameters statically. + */ + mac[i].dyn_learn = true; + mac[i].ingress = true; + mac[i].egress = true; + } + } + + return 0; +} + +static int sja1105_init_mii_settings(struct sja1105_private *priv, + struct sja1105_dt_port *ports) +{ + struct device *dev = &priv->spidev->dev; + struct sja1105_xmii_params_entry *mii; + struct sja1105_table *table; + int i; + + table = &priv->static_config.tables[BLK_IDX_XMII_PARAMS]; + + /* Discard previous xMII Mode Parameters Table */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_XMII_PARAMS_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + /* Override table based on phylib DT bindings */ + table->entry_count = SJA1105_MAX_XMII_PARAMS_COUNT; + + mii = table->entries; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + switch (ports[i].phy_mode) { + case PHY_INTERFACE_MODE_MII: + mii->xmii_mode[i] = XMII_MODE_MII; + break; + case PHY_INTERFACE_MODE_RMII: + mii->xmii_mode[i] = XMII_MODE_RMII; + break; + case PHY_INTERFACE_MODE_RGMII: + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_RXID: + case PHY_INTERFACE_MODE_RGMII_TXID: + mii->xmii_mode[i] = XMII_MODE_RGMII; + break; + default: + dev_err(dev, "Unsupported PHY mode %s!\n", + phy_modes(ports[i].phy_mode)); + } + + mii->phy_mac[i] = ports[i].role; + } + return 0; +} + +static int sja1105_init_static_fdb(struct sja1105_private *priv) +{ + struct sja1105_table *table; + + table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP]; + + /* We only populate the FDB table through dynamic + * L2 Address Lookup entries + */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + return 0; +} + +static int sja1105_init_l2_lookup_params(struct sja1105_private *priv) +{ + struct sja1105_table *table; + struct sja1105_l2_lookup_params_entry default_l2_lookup_params = { + /* Learned FDB entries are forgotten after 300 seconds */ + .maxage = SJA1105_AGEING_TIME_MS(300000), + /* All entries within a FDB bin are available for learning */ + .dyn_tbsz = SJA1105ET_FDB_BIN_SIZE, + /* 2^8 + 2^5 + 2^3 + 2^2 + 2^1 + 1 in Koopman notation */ + .poly = 0x97, + /* This selects between Independent VLAN Learning (IVL) and + * Shared VLAN Learning (SVL) + */ + .shared_learn = false, + /* Don't discard management traffic based on ENFPORT - + * we don't perform SMAC port enforcement anyway, so + * what we are setting here doesn't matter. + */ + .no_enf_hostprt = false, + /* Don't learn SMAC for mac_fltres1 and mac_fltres0. + * Maybe correlate with no_linklocal_learn from bridge driver? + */ + .no_mgmt_learn = true, + }; + + table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS]; + + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_L2_LOOKUP_PARAMS_COUNT; + + /* This table only has a single entry */ + ((struct sja1105_l2_lookup_params_entry *)table->entries)[0] = + default_l2_lookup_params; + + return 0; +} + +static int sja1105_init_static_vlan(struct sja1105_private *priv) +{ + struct sja1105_table *table; + struct sja1105_vlan_lookup_entry pvid = { + .ving_mirr = 0, + .vegr_mirr = 0, + .vmemb_port = 0, + .vlan_bc = 0, + .tag_port = 0, + .vlanid = 0, + }; + int i; + + table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP]; + + /* The static VLAN table will only contain the initial pvid of 0. + * All other VLANs are to be configured through dynamic entries, + * and kept in the static configuration table as backing memory. + * The pvid of 0 is sufficient to pass traffic while the ports are + * standalone and when vlan_filtering is disabled. When filtering + * gets enabled, the switchdev core sets up the VLAN ID 1 and sets + * it as the new pvid. Actually 'pvid 1' still comes up in 'bridge + * vlan' even when vlan_filtering is off, but it has no effect. + */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(1, table->ops->unpacked_entry_size, + GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = 1; + + /* VLAN ID 0: all DT-defined ports are members; no restrictions on + * forwarding; always transmit priority-tagged frames as untagged. + */ + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + pvid.vmemb_port |= BIT(i); + pvid.vlan_bc |= BIT(i); + pvid.tag_port &= ~BIT(i); + } + + ((struct sja1105_vlan_lookup_entry *)table->entries)[0] = pvid; + return 0; +} + +static int sja1105_init_l2_forwarding(struct sja1105_private *priv) +{ + struct sja1105_l2_forwarding_entry *l2fwd; + struct sja1105_table *table; + int i, j; + + table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING]; + + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_L2_FORWARDING_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_L2_FORWARDING_COUNT; + + l2fwd = table->entries; + + /* First 5 entries define the forwarding rules */ + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + unsigned int upstream = dsa_upstream_port(priv->ds, i); + + for (j = 0; j < SJA1105_NUM_TC; j++) + l2fwd[i].vlan_pmap[j] = j; + + if (i == upstream) + continue; + + sja1105_port_allow_traffic(l2fwd, i, upstream, true); + sja1105_port_allow_traffic(l2fwd, upstream, i, true); + } + /* Next 8 entries define VLAN PCP mapping from ingress to egress. + * Create a one-to-one mapping. + */ + for (i = 0; i < SJA1105_NUM_TC; i++) + for (j = 0; j < SJA1105_NUM_PORTS; j++) + l2fwd[SJA1105_NUM_PORTS + i].vlan_pmap[j] = i; + + return 0; +} + +static int sja1105_init_l2_forwarding_params(struct sja1105_private *priv) +{ + struct sja1105_l2_forwarding_params_entry default_l2fwd_params = { + /* Disallow dynamic reconfiguration of vlan_pmap */ + .max_dynp = 0, + /* Use a single memory partition for all ingress queues */ + .part_spc = { SJA1105_MAX_FRAME_MEMORY, 0, 0, 0, 0, 0, 0, 0 }, + }; + struct sja1105_table *table; + + table = &priv->static_config.tables[BLK_IDX_L2_FORWARDING_PARAMS]; + + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_L2_FORWARDING_PARAMS_COUNT; + + /* This table only has a single entry */ + ((struct sja1105_l2_forwarding_params_entry *)table->entries)[0] = + default_l2fwd_params; + + return 0; +} + +static int sja1105_init_general_params(struct sja1105_private *priv) +{ + struct sja1105_general_params_entry default_general_params = { + /* Disallow dynamic changing of the mirror port */ + .mirr_ptacu = 0, + .switchid = priv->ds->index, + /* Priority queue for link-local frames trapped to CPU */ + .hostprio = 0, + .mac_fltres1 = SJA1105_LINKLOCAL_FILTER_A, + .mac_flt1 = SJA1105_LINKLOCAL_FILTER_A_MASK, + .incl_srcpt1 = true, + .send_meta1 = false, + .mac_fltres0 = SJA1105_LINKLOCAL_FILTER_B, + .mac_flt0 = SJA1105_LINKLOCAL_FILTER_B_MASK, + .incl_srcpt0 = true, + .send_meta0 = false, + /* The destination for traffic matching mac_fltres1 and + * mac_fltres0 on all ports except host_port. Such traffic + * receieved on host_port itself would be dropped, except + * by installing a temporary 'management route' + */ + .host_port = dsa_upstream_port(priv->ds, 0), + /* Same as host port */ + .mirr_port = dsa_upstream_port(priv->ds, 0), + /* Link-local traffic received on casc_port will be forwarded + * to host_port without embedding the source port and device ID + * info in the destination MAC address (presumably because it + * is a cascaded port and a downstream SJA switch already did + * that). Default to an invalid port (to disable the feature) + * and overwrite this if we find any DSA (cascaded) ports. + */ + .casc_port = SJA1105_NUM_PORTS, + /* No TTEthernet */ + .vllupformat = 0, + .vlmarker = 0, + .vlmask = 0, + /* Only update correctionField for 1-step PTP (L2 transport) */ + .ignore2stf = 0, + /* Forcefully disable VLAN filtering by telling + * the switch that VLAN has a different EtherType. + */ + .tpid = ETH_P_SJA1105, + .tpid2 = ETH_P_SJA1105, + }; + struct sja1105_table *table; + int i, k = 0; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + if (dsa_is_dsa_port(priv->ds, i)) + default_general_params.casc_port = i; + else if (dsa_is_user_port(priv->ds, i)) + priv->ports[i].mgmt_slot = k++; + } + + table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS]; + + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_GENERAL_PARAMS_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_GENERAL_PARAMS_COUNT; + + /* This table only has a single entry */ + ((struct sja1105_general_params_entry *)table->entries)[0] = + default_general_params; + + return 0; +} + +#define SJA1105_RATE_MBPS(speed) (((speed) * 64000) / 1000) + +static inline void +sja1105_setup_policer(struct sja1105_l2_policing_entry *policing, + int index) +{ + policing[index].sharindx = index; + policing[index].smax = 65535; /* Burst size in bytes */ + policing[index].rate = SJA1105_RATE_MBPS(1000); + policing[index].maxlen = ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN; + policing[index].partition = 0; +} + +static int sja1105_init_l2_policing(struct sja1105_private *priv) +{ + struct sja1105_l2_policing_entry *policing; + struct sja1105_table *table; + int i, j, k; + + table = &priv->static_config.tables[BLK_IDX_L2_POLICING]; + + /* Discard previous L2 Policing Table */ + if (table->entry_count) { + kfree(table->entries); + table->entry_count = 0; + } + + table->entries = kcalloc(SJA1105_MAX_L2_POLICING_COUNT, + table->ops->unpacked_entry_size, GFP_KERNEL); + if (!table->entries) + return -ENOMEM; + + table->entry_count = SJA1105_MAX_L2_POLICING_COUNT; + + policing = table->entries; + + /* k sweeps through all unicast policers (0-39). + * bcast sweeps through policers 40-44. + */ + for (i = 0, k = 0; i < SJA1105_NUM_PORTS; i++) { + int bcast = (SJA1105_NUM_PORTS * SJA1105_NUM_TC) + i; + + for (j = 0; j < SJA1105_NUM_TC; j++, k++) + sja1105_setup_policer(policing, k); + + /* Set up this port's policer for broadcast traffic */ + sja1105_setup_policer(policing, bcast); + } + return 0; +} + +static int sja1105_static_config_load(struct sja1105_private *priv, + struct sja1105_dt_port *ports) +{ + int rc; + + sja1105_static_config_free(&priv->static_config); + rc = sja1105_static_config_init(&priv->static_config, + priv->info->static_ops, + priv->info->device_id); + if (rc) + return rc; + + /* Build static configuration */ + rc = sja1105_init_mac_settings(priv); + if (rc < 0) + return rc; + rc = sja1105_init_mii_settings(priv, ports); + if (rc < 0) + return rc; + rc = sja1105_init_static_fdb(priv); + if (rc < 0) + return rc; + rc = sja1105_init_static_vlan(priv); + if (rc < 0) + return rc; + rc = sja1105_init_l2_lookup_params(priv); + if (rc < 0) + return rc; + rc = sja1105_init_l2_forwarding(priv); + if (rc < 0) + return rc; + rc = sja1105_init_l2_forwarding_params(priv); + if (rc < 0) + return rc; + rc = sja1105_init_l2_policing(priv); + if (rc < 0) + return rc; + rc = sja1105_init_general_params(priv); + if (rc < 0) + return rc; + + /* Send initial configuration to hardware via SPI */ + return sja1105_static_config_upload(priv); +} + +static int sja1105_parse_rgmii_delays(struct sja1105_private *priv, + const struct sja1105_dt_port *ports) +{ + int i; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + if (ports->role == XMII_MAC) + continue; + + if (ports->phy_mode == PHY_INTERFACE_MODE_RGMII_RXID || + ports->phy_mode == PHY_INTERFACE_MODE_RGMII_ID) + priv->rgmii_rx_delay[i] = true; + + if (ports->phy_mode == PHY_INTERFACE_MODE_RGMII_TXID || + ports->phy_mode == PHY_INTERFACE_MODE_RGMII_ID) + priv->rgmii_tx_delay[i] = true; + + if ((priv->rgmii_rx_delay[i] || priv->rgmii_tx_delay[i]) && + !priv->info->setup_rgmii_delay) + return -EINVAL; + } + return 0; +} + +static int sja1105_parse_ports_node(struct sja1105_private *priv, + struct sja1105_dt_port *ports, + struct device_node *ports_node) +{ + struct device *dev = &priv->spidev->dev; + struct device_node *child; + + for_each_child_of_node(ports_node, child) { + struct device_node *phy_node; + int phy_mode; + u32 index; + + /* Get switch port number from DT */ + if (of_property_read_u32(child, "reg", &index) < 0) { + dev_err(dev, "Port number not defined in device tree " + "(property \"reg\")\n"); + return -ENODEV; + } + + /* Get PHY mode from DT */ + phy_mode = of_get_phy_mode(child); + if (phy_mode < 0) { + dev_err(dev, "Failed to read phy-mode or " + "phy-interface-type property for port %d\n", + index); + return -ENODEV; + } + ports[index].phy_mode = phy_mode; + + phy_node = of_parse_phandle(child, "phy-handle", 0); + if (!phy_node) { + if (!of_phy_is_fixed_link(child)) { + dev_err(dev, "phy-handle or fixed-link " + "properties missing!\n"); + return -ENODEV; + } + /* phy-handle is missing, but fixed-link isn't. + * So it's a fixed link. Default to PHY role. + */ + ports[index].role = XMII_PHY; + } else { + /* phy-handle present => put port in MAC role */ + ports[index].role = XMII_MAC; + of_node_put(phy_node); + } + + /* The MAC/PHY role can be overridden with explicit bindings */ + if (of_property_read_bool(child, "sja1105,role-mac")) + ports[index].role = XMII_MAC; + else if (of_property_read_bool(child, "sja1105,role-phy")) + ports[index].role = XMII_PHY; + } + + return 0; +} + +static int sja1105_parse_dt(struct sja1105_private *priv, + struct sja1105_dt_port *ports) +{ + struct device *dev = &priv->spidev->dev; + struct device_node *switch_node = dev->of_node; + struct device_node *ports_node; + int rc; + + ports_node = of_get_child_by_name(switch_node, "ports"); + if (!ports_node) { + dev_err(dev, "Incorrect bindings: absent \"ports\" node\n"); + return -ENODEV; + } + + rc = sja1105_parse_ports_node(priv, ports, ports_node); + of_node_put(ports_node); + + return rc; +} + +/* Convert back and forth MAC speed from Mbps to SJA1105 encoding */ +static int sja1105_speed[] = { + [SJA1105_SPEED_AUTO] = 0, + [SJA1105_SPEED_10MBPS] = 10, + [SJA1105_SPEED_100MBPS] = 100, + [SJA1105_SPEED_1000MBPS] = 1000, +}; + +static sja1105_speed_t sja1105_get_speed_cfg(unsigned int speed_mbps) +{ + int i; + + for (i = SJA1105_SPEED_AUTO; i <= SJA1105_SPEED_1000MBPS; i++) + if (sja1105_speed[i] == speed_mbps) + return i; + return -EINVAL; +} + +/* Set link speed and enable/disable traffic I/O in the MAC configuration + * for a specific port. + * + * @speed_mbps: If 0, leave the speed unchanged, else adapt MAC to PHY speed. + * @enabled: Manage Rx and Tx settings for this port. If false, overrides the + * settings from the STP state, but not persistently (does not + * overwrite the static MAC info for this port). + */ +static int sja1105_adjust_port_config(struct sja1105_private *priv, int port, + int speed_mbps, bool enabled) +{ + struct sja1105_mac_config_entry dyn_mac; + struct sja1105_xmii_params_entry *mii; + struct sja1105_mac_config_entry *mac; + struct device *dev = priv->ds->dev; + sja1105_phy_interface_t phy_mode; + sja1105_speed_t speed; + int rc; + + mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries; + mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; + + speed = sja1105_get_speed_cfg(speed_mbps); + if (speed_mbps && speed < 0) { + dev_err(dev, "Invalid speed %iMbps\n", speed_mbps); + return -EINVAL; + } + + /* If requested, overwrite SJA1105_SPEED_AUTO from the static MAC + * configuration table, since this will be used for the clocking setup, + * and we no longer need to store it in the static config (already told + * hardware we want auto during upload phase). + */ + if (speed_mbps) + mac[port].speed = speed; + else + mac[port].speed = SJA1105_SPEED_AUTO; + + /* On P/Q/R/S, one can read from the device via the MAC reconfiguration + * tables. On E/T, MAC reconfig tables are not readable, only writable. + * We have to *know* what the MAC looks like. For the sake of keeping + * the code common, we'll use the static configuration tables as a + * reasonable approximation for both E/T and P/Q/R/S. + */ + dyn_mac = mac[port]; + dyn_mac.ingress = enabled && mac[port].ingress; + dyn_mac.egress = enabled && mac[port].egress; + + /* Write to the dynamic reconfiguration tables */ + rc = sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, + port, &dyn_mac, true); + if (rc < 0) { + dev_err(dev, "Failed to write MAC config: %d\n", rc); + return rc; + } + + /* Reconfigure the PLLs for the RGMII interfaces (required 125 MHz at + * gigabit, 25 MHz at 100 Mbps and 2.5 MHz at 10 Mbps). For MII and + * RMII no change of the clock setup is required. Actually, changing + * the clock setup does interrupt the clock signal for a certain time + * which causes trouble for all PHYs relying on this signal. + */ + if (!enabled) + return 0; + + phy_mode = mii->xmii_mode[port]; + if (phy_mode != XMII_MODE_RGMII) + return 0; + + return sja1105_clocking_setup_port(priv, port); +} + +static void sja1105_adjust_link(struct dsa_switch *ds, int port, + struct phy_device *phydev) +{ + struct sja1105_private *priv = ds->priv; + + if (!phydev->link) + sja1105_adjust_port_config(priv, port, 0, false); + else + sja1105_adjust_port_config(priv, port, phydev->speed, true); +} + +static void sja1105_phylink_validate(struct dsa_switch *ds, int port, + unsigned long *supported, + struct phylink_link_state *state) +{ + /* Construct a new mask which exhaustively contains all link features + * supported by the MAC, and then apply that (logical AND) to what will + * be sent to the PHY for "marketing". + */ + __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; + struct sja1105_private *priv = ds->priv; + struct sja1105_xmii_params_entry *mii; + + mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries; + + /* The MAC does not support pause frames, and also doesn't + * support half-duplex traffic modes. + */ + phylink_set(mask, Autoneg); + phylink_set(mask, MII); + phylink_set(mask, 10baseT_Full); + phylink_set(mask, 100baseT_Full); + if (mii->xmii_mode[port] == XMII_MODE_RGMII) + phylink_set(mask, 1000baseT_Full); + + bitmap_and(supported, supported, mask, __ETHTOOL_LINK_MODE_MASK_NBITS); + bitmap_and(state->advertising, state->advertising, mask, + __ETHTOOL_LINK_MODE_MASK_NBITS); +} + +/* First-generation switches have a 4-way set associative TCAM that + * holds the FDB entries. An FDB index spans from 0 to 1023 and is comprised of + * a "bin" (grouping of 4 entries) and a "way" (an entry within a bin). + * For the placement of a newly learnt FDB entry, the switch selects the bin + * based on a hash function, and the way within that bin incrementally. + */ +static inline int sja1105et_fdb_index(int bin, int way) +{ + return bin * SJA1105ET_FDB_BIN_SIZE + way; +} + +static int sja1105_is_fdb_entry_in_bin(struct sja1105_private *priv, int bin, + const u8 *addr, u16 vid, + struct sja1105_l2_lookup_entry *match, + int *last_unused) +{ + int way; + + for (way = 0; way < SJA1105ET_FDB_BIN_SIZE; way++) { + struct sja1105_l2_lookup_entry l2_lookup = {0}; + int index = sja1105et_fdb_index(bin, way); + + /* Skip unused entries, optionally marking them + * into the return value + */ + if (sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP, + index, &l2_lookup)) { + if (last_unused) + *last_unused = way; + continue; + } + + if (l2_lookup.macaddr == ether_addr_to_u64(addr) && + l2_lookup.vlanid == vid) { + if (match) + *match = l2_lookup; + return way; + } + } + /* Return an invalid entry index if not found */ + return -1; +} + +static int sja1105_fdb_add(struct dsa_switch *ds, int port, + const unsigned char *addr, u16 vid) +{ + struct sja1105_l2_lookup_entry l2_lookup = {0}; + struct sja1105_private *priv = ds->priv; + struct device *dev = ds->dev; + int last_unused = -1; + int bin, way; + + bin = sja1105_fdb_hash(priv, addr, vid); + + way = sja1105_is_fdb_entry_in_bin(priv, bin, addr, vid, + &l2_lookup, &last_unused); + if (way >= 0) { + /* We have an FDB entry. Is our port in the destination + * mask? If yes, we need to do nothing. If not, we need + * to rewrite the entry by adding this port to it. + */ + if (l2_lookup.destports & BIT(port)) + return 0; + l2_lookup.destports |= BIT(port); + } else { + int index = sja1105et_fdb_index(bin, way); + + /* We don't have an FDB entry. We construct a new one and + * try to find a place for it within the FDB table. + */ + l2_lookup.macaddr = ether_addr_to_u64(addr); + l2_lookup.destports = BIT(port); + l2_lookup.vlanid = vid; + + if (last_unused >= 0) { + way = last_unused; + } else { + /* Bin is full, need to evict somebody. + * Choose victim at random. If you get these messages + * often, you may need to consider changing the + * distribution function: + * static_config[BLK_IDX_L2_LOOKUP_PARAMS].entries->poly + */ + get_random_bytes(&way, sizeof(u8)); + way %= SJA1105ET_FDB_BIN_SIZE; + dev_warn(dev, "Warning, FDB bin %d full while adding entry for %pM. Evicting entry %u.\n", + bin, addr, way); + /* Evict entry */ + sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, + index, NULL, false); + } + } + l2_lookup.index = sja1105et_fdb_index(bin, way); + + return sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, + l2_lookup.index, &l2_lookup, + true); +} + +static int sja1105_fdb_del(struct dsa_switch *ds, int port, + const unsigned char *addr, u16 vid) +{ + struct sja1105_l2_lookup_entry l2_lookup = {0}; + struct sja1105_private *priv = ds->priv; + int index, bin, way; + bool keep; + + bin = sja1105_fdb_hash(priv, addr, vid); + way = sja1105_is_fdb_entry_in_bin(priv, bin, addr, vid, + &l2_lookup, NULL); + if (way < 0) + return 0; + index = sja1105et_fdb_index(bin, way); + + /* We have an FDB entry. Is our port in the destination mask? If yes, + * we need to remove it. If the resulting port mask becomes empty, we + * need to completely evict the FDB entry. + * Otherwise we just write it back. + */ + if (l2_lookup.destports & BIT(port)) + l2_lookup.destports &= ~BIT(port); + if (l2_lookup.destports) + keep = true; + else + keep = false; + + return sja1105_dynamic_config_write(priv, BLK_IDX_L2_LOOKUP, + index, &l2_lookup, keep); +} + +static int sja1105_fdb_dump(struct dsa_switch *ds, int port, + dsa_fdb_dump_cb_t *cb, void *data) +{ + struct sja1105_private *priv = ds->priv; + struct device *dev = ds->dev; + int i; + + for (i = 0; i < SJA1105_MAX_L2_LOOKUP_COUNT; i++) { + struct sja1105_l2_lookup_entry l2_lookup = {0}; + u8 macaddr[ETH_ALEN]; + int rc; + + rc = sja1105_dynamic_config_read(priv, BLK_IDX_L2_LOOKUP, + i, &l2_lookup); + /* No fdb entry at i, not an issue */ + if (rc == -EINVAL) + continue; + if (rc) { + dev_err(dev, "Failed to dump FDB: %d\n", rc); + return rc; + } + + /* FDB dump callback is per port. This means we have to + * disregard a valid entry if it's not for this port, even if + * only to revisit it later. This is inefficient because the + * 1024-sized FDB table needs to be traversed 4 times through + * SPI during a 'bridge fdb show' command. + */ + if (!(l2_lookup.destports & BIT(port))) + continue; + u64_to_ether_addr(l2_lookup.macaddr, macaddr); + cb(macaddr, l2_lookup.vlanid, false, data); + } + return 0; +} + +/* This callback needs to be present */ +static int sja1105_mdb_prepare(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_mdb *mdb) +{ + return 0; +} + +static void sja1105_mdb_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_mdb *mdb) +{ + sja1105_fdb_add(ds, port, mdb->addr, mdb->vid); +} + +static int sja1105_mdb_del(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_mdb *mdb) +{ + return sja1105_fdb_del(ds, port, mdb->addr, mdb->vid); +} + +static int sja1105_bridge_member(struct dsa_switch *ds, int port, + struct net_device *br, bool member) +{ + struct sja1105_l2_forwarding_entry *l2_fwd; + struct sja1105_private *priv = ds->priv; + int i, rc; + + l2_fwd = priv->static_config.tables[BLK_IDX_L2_FORWARDING].entries; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + /* Add this port to the forwarding matrix of the + * other ports in the same bridge, and viceversa. + */ + if (!dsa_is_user_port(ds, i)) + continue; + /* For the ports already under the bridge, only one thing needs + * to be done, and that is to add this port to their + * reachability domain. So we can perform the SPI write for + * them immediately. However, for this port itself (the one + * that is new to the bridge), we need to add all other ports + * to its reachability domain. So we do that incrementally in + * this loop, and perform the SPI write only at the end, once + * the domain contains all other bridge ports. + */ + if (i == port) + continue; + if (dsa_to_port(ds, i)->bridge_dev != br) + continue; + sja1105_port_allow_traffic(l2_fwd, i, port, member); + sja1105_port_allow_traffic(l2_fwd, port, i, member); + + rc = sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING, + i, &l2_fwd[i], true); + if (rc < 0) + return rc; + } + + return sja1105_dynamic_config_write(priv, BLK_IDX_L2_FORWARDING, + port, &l2_fwd[port], true); +} + +static void sja1105_bridge_stp_state_set(struct dsa_switch *ds, int port, + u8 state) +{ + struct sja1105_private *priv = ds->priv; + struct sja1105_mac_config_entry *mac; + + mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; + + switch (state) { + case BR_STATE_DISABLED: + case BR_STATE_BLOCKING: + /* From UM10944 description of DRPDTAG (why put this there?): + * "Management traffic flows to the port regardless of the state + * of the INGRESS flag". So BPDUs are still be allowed to pass. + * At the moment no difference between DISABLED and BLOCKING. + */ + mac[port].ingress = false; + mac[port].egress = false; + mac[port].dyn_learn = false; + break; + case BR_STATE_LISTENING: + mac[port].ingress = true; + mac[port].egress = false; + mac[port].dyn_learn = false; + break; + case BR_STATE_LEARNING: + mac[port].ingress = true; + mac[port].egress = false; + mac[port].dyn_learn = true; + break; + case BR_STATE_FORWARDING: + mac[port].ingress = true; + mac[port].egress = true; + mac[port].dyn_learn = true; + break; + default: + dev_err(ds->dev, "invalid STP state: %d\n", state); + return; + } + + sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port, + &mac[port], true); +} + +static int sja1105_bridge_join(struct dsa_switch *ds, int port, + struct net_device *br) +{ + return sja1105_bridge_member(ds, port, br, true); +} + +static void sja1105_bridge_leave(struct dsa_switch *ds, int port, + struct net_device *br) +{ + sja1105_bridge_member(ds, port, br, false); +} + +static u8 sja1105_stp_state_get(struct sja1105_private *priv, int port) +{ + struct sja1105_mac_config_entry *mac; + + mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; + + if (!mac[port].ingress && !mac[port].egress && !mac[port].dyn_learn) + return BR_STATE_BLOCKING; + if (mac[port].ingress && !mac[port].egress && !mac[port].dyn_learn) + return BR_STATE_LISTENING; + if (mac[port].ingress && !mac[port].egress && mac[port].dyn_learn) + return BR_STATE_LEARNING; + if (mac[port].ingress && mac[port].egress && mac[port].dyn_learn) + return BR_STATE_FORWARDING; + return -EINVAL; +} + +/* For situations where we need to change a setting at runtime that is only + * available through the static configuration, resetting the switch in order + * to upload the new static config is unavoidable. Back up the settings we + * modify at runtime (currently only MAC) and restore them after uploading, + * such that this operation is relatively seamless. + */ +static int sja1105_static_config_reload(struct sja1105_private *priv) +{ + struct sja1105_mac_config_entry *mac; + int speed_mbps[SJA1105_NUM_PORTS]; + u8 stp_state[SJA1105_NUM_PORTS]; + int rc, i; + + mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; + + /* Back up settings changed by sja1105_adjust_port_config and + * sja1105_bridge_stp_state_set and restore their defaults. + */ + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + speed_mbps[i] = sja1105_speed[mac[i].speed]; + mac[i].speed = SJA1105_SPEED_AUTO; + if (i == dsa_upstream_port(priv->ds, i)) { + mac[i].ingress = true; + mac[i].egress = true; + mac[i].dyn_learn = true; + } else { + stp_state[i] = sja1105_stp_state_get(priv, i); + mac[i].ingress = false; + mac[i].egress = false; + mac[i].dyn_learn = false; + } + } + + /* Reset switch and send updated static configuration */ + rc = sja1105_static_config_upload(priv); + if (rc < 0) + goto out; + + /* Configure the CGU (PLLs) for MII and RMII PHYs. + * For these interfaces there is no dynamic configuration + * needed, since PLLs have same settings at all speeds. + */ + rc = sja1105_clocking_setup(priv); + if (rc < 0) + goto out; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + bool enabled = (speed_mbps[i] != 0); + + if (i != dsa_upstream_port(priv->ds, i)) + sja1105_bridge_stp_state_set(priv->ds, i, stp_state[i]); + + rc = sja1105_adjust_port_config(priv, i, speed_mbps[i], + enabled); + if (rc < 0) + goto out; + } +out: + return rc; +} + +/* The TPID setting belongs to the General Parameters table, + * which can only be partially reconfigured at runtime (and not the TPID). + * So a switch reset is required. + */ +static int sja1105_change_tpid(struct sja1105_private *priv, + u16 tpid, u16 tpid2) +{ + struct sja1105_general_params_entry *general_params; + struct sja1105_table *table; + + table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS]; + general_params = table->entries; + general_params->tpid = tpid; + general_params->tpid2 = tpid2; + return sja1105_static_config_reload(priv); +} + +static int sja1105_pvid_apply(struct sja1105_private *priv, int port, u16 pvid) +{ + struct sja1105_mac_config_entry *mac; + + mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries; + + mac[port].vlanid = pvid; + + return sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port, + &mac[port], true); +} + +static int sja1105_is_vlan_configured(struct sja1105_private *priv, u16 vid) +{ + struct sja1105_vlan_lookup_entry *vlan; + int count, i; + + vlan = priv->static_config.tables[BLK_IDX_VLAN_LOOKUP].entries; + count = priv->static_config.tables[BLK_IDX_VLAN_LOOKUP].entry_count; + + for (i = 0; i < count; i++) + if (vlan[i].vlanid == vid) + return i; + + /* Return an invalid entry index if not found */ + return -1; +} + +static int sja1105_vlan_apply(struct sja1105_private *priv, int port, u16 vid, + bool enabled, bool untagged) +{ + struct sja1105_vlan_lookup_entry *vlan; + struct sja1105_table *table; + bool keep = true; + int match, rc; + + table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP]; + + match = sja1105_is_vlan_configured(priv, vid); + if (match < 0) { + /* Can't delete a missing entry. */ + if (!enabled) + return 0; + rc = sja1105_table_resize(table, table->entry_count + 1); + if (rc) + return rc; + match = table->entry_count - 1; + } + /* Assign pointer after the resize (it's new memory) */ + vlan = table->entries; + vlan[match].vlanid = vid; + if (enabled) { + vlan[match].vlan_bc |= BIT(port); + vlan[match].vmemb_port |= BIT(port); + } else { + vlan[match].vlan_bc &= ~BIT(port); + vlan[match].vmemb_port &= ~BIT(port); + } + /* Also unset tag_port if removing this VLAN was requested, + * just so we don't have a confusing bitmap (no practical purpose). + */ + if (untagged || !enabled) + vlan[match].tag_port &= ~BIT(port); + else + vlan[match].tag_port |= BIT(port); + /* If there's no port left as member of this VLAN, + * it's time for it to go. + */ + if (!vlan[match].vmemb_port) + keep = false; + + dev_dbg(priv->ds->dev, + "%s: port %d, vid %llu, broadcast domain 0x%llx, " + "port members 0x%llx, tagged ports 0x%llx, keep %d\n", + __func__, port, vlan[match].vlanid, vlan[match].vlan_bc, + vlan[match].vmemb_port, vlan[match].tag_port, keep); + + rc = sja1105_dynamic_config_write(priv, BLK_IDX_VLAN_LOOKUP, vid, + &vlan[match], keep); + if (rc < 0) + return rc; + + if (!keep) + return sja1105_table_delete_entry(table, match); + + return 0; +} + +static int sja1105_setup_8021q_tagging(struct dsa_switch *ds, bool enabled) +{ + int rc, i; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + rc = dsa_port_setup_8021q_tagging(ds, i, enabled); + if (rc < 0) { + dev_err(ds->dev, "Failed to setup VLAN tagging for port %d: %d\n", + i, rc); + return rc; + } + } + dev_info(ds->dev, "%s switch tagging\n", + enabled ? "Enabled" : "Disabled"); + return 0; +} + +static enum dsa_tag_protocol +sja1105_get_tag_protocol(struct dsa_switch *ds, int port) +{ + return DSA_TAG_PROTO_SJA1105; +} + +/* This callback needs to be present */ +static int sja1105_vlan_prepare(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) +{ + return 0; +} + +static int sja1105_vlan_filtering(struct dsa_switch *ds, int port, bool enabled) +{ + struct sja1105_private *priv = ds->priv; + int rc; + + if (enabled) + /* Enable VLAN filtering. */ + rc = sja1105_change_tpid(priv, ETH_P_8021Q, ETH_P_8021AD); + else + /* Disable VLAN filtering. */ + rc = sja1105_change_tpid(priv, ETH_P_SJA1105, ETH_P_SJA1105); + if (rc) + dev_err(ds->dev, "Failed to change VLAN Ethertype\n"); + + /* Switch port identification based on 802.1Q is only passable + * if we are not under a vlan_filtering bridge. So make sure + * the two configurations are mutually exclusive. + */ + return sja1105_setup_8021q_tagging(ds, !enabled); +} + +static void sja1105_vlan_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) +{ + struct sja1105_private *priv = ds->priv; + u16 vid; + int rc; + + for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) { + rc = sja1105_vlan_apply(priv, port, vid, true, vlan->flags & + BRIDGE_VLAN_INFO_UNTAGGED); + if (rc < 0) { + dev_err(ds->dev, "Failed to add VLAN %d to port %d: %d\n", + vid, port, rc); + return; + } + if (vlan->flags & BRIDGE_VLAN_INFO_PVID) { + rc = sja1105_pvid_apply(ds->priv, port, vid); + if (rc < 0) { + dev_err(ds->dev, "Failed to set pvid %d on port %d: %d\n", + vid, port, rc); + return; + } + } + } +} + +static int sja1105_vlan_del(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) +{ + struct sja1105_private *priv = ds->priv; + u16 vid; + int rc; + + for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) { + rc = sja1105_vlan_apply(priv, port, vid, false, vlan->flags & + BRIDGE_VLAN_INFO_UNTAGGED); + if (rc < 0) { + dev_err(ds->dev, "Failed to remove VLAN %d from port %d: %d\n", + vid, port, rc); + return rc; + } + } + return 0; +} + +/* The programming model for the SJA1105 switch is "all-at-once" via static + * configuration tables. Some of these can be dynamically modified at runtime, + * but not the xMII mode parameters table. + * Furthermode, some PHYs may not have crystals for generating their clocks + * (e.g. RMII). Instead, their 50MHz clock is supplied via the SJA1105 port's + * ref_clk pin. So port clocking needs to be initialized early, before + * connecting to PHYs is attempted, otherwise they won't respond through MDIO. + * Setting correct PHY link speed does not matter now. + * But dsa_slave_phy_setup is called later than sja1105_setup, so the PHY + * bindings are not yet parsed by DSA core. We need to parse early so that we + * can populate the xMII mode parameters table. + */ +static int sja1105_setup(struct dsa_switch *ds) +{ + struct sja1105_dt_port ports[SJA1105_NUM_PORTS]; + struct sja1105_private *priv = ds->priv; + int rc; + + rc = sja1105_parse_dt(priv, ports); + if (rc < 0) { + dev_err(ds->dev, "Failed to parse DT: %d\n", rc); + return rc; + } + + /* Error out early if internal delays are required through DT + * and we can't apply them. + */ + rc = sja1105_parse_rgmii_delays(priv, ports); + if (rc < 0) { + dev_err(ds->dev, "RGMII delay not supported\n"); + return rc; + } + + /* Create and send configuration down to device */ + rc = sja1105_static_config_load(priv, ports); + if (rc < 0) { + dev_err(ds->dev, "Failed to load static config: %d\n", rc); + return rc; + } + /* Configure the CGU (PHY link modes and speeds) */ + rc = sja1105_clocking_setup(priv); + if (rc < 0) { + dev_err(ds->dev, "Failed to configure MII clocking: %d\n", rc); + return rc; + } + /* On SJA1105, VLAN filtering per se is always enabled in hardware. + * The only thing we can do to disable it is lie about what the 802.1Q + * EtherType is. + * So it will still try to apply VLAN filtering, but all ingress + * traffic (except frames received with EtherType of ETH_P_SJA1105) + * will be internally tagged with a distorted VLAN header where the + * TPID is ETH_P_SJA1105, and the VLAN ID is the port pvid. + */ + ds->vlan_filtering_is_global = true; + + /* The DSA/switchdev model brings up switch ports in standalone mode by + * default, and that means vlan_filtering is 0 since they're not under + * a bridge, so it's safe to set up switch tagging at this time. + */ + return sja1105_setup_8021q_tagging(ds, true); +} + +static int sja1105_mgmt_xmit(struct dsa_switch *ds, int port, int slot, + struct sk_buff *skb) +{ + struct sja1105_mgmt_entry mgmt_route = {0}; + struct sja1105_private *priv = ds->priv; + struct ethhdr *hdr; + int timeout = 10; + int rc; + + hdr = eth_hdr(skb); + + mgmt_route.macaddr = ether_addr_to_u64(hdr->h_dest); + mgmt_route.destports = BIT(port); + mgmt_route.enfport = 1; + + rc = sja1105_dynamic_config_write(priv, BLK_IDX_MGMT_ROUTE, + slot, &mgmt_route, true); + if (rc < 0) { + kfree_skb(skb); + return rc; + } + + /* Transfer skb to the host port. */ + dsa_enqueue_skb(skb, ds->ports[port].slave); + + /* Wait until the switch has processed the frame */ + do { + rc = sja1105_dynamic_config_read(priv, BLK_IDX_MGMT_ROUTE, + slot, &mgmt_route); + if (rc < 0) { + dev_err_ratelimited(priv->ds->dev, + "failed to poll for mgmt route\n"); + continue; + } + + /* UM10944: The ENFPORT flag of the respective entry is + * cleared when a match is found. The host can use this + * flag as an acknowledgment. + */ + cpu_relax(); + } while (mgmt_route.enfport && --timeout); + + if (!timeout) { + /* Clean up the management route so that a follow-up + * frame may not match on it by mistake. + */ + sja1105_dynamic_config_write(priv, BLK_IDX_MGMT_ROUTE, + slot, &mgmt_route, false); + dev_err_ratelimited(priv->ds->dev, "xmit timed out\n"); + } + + return NETDEV_TX_OK; +} + +/* Deferred work is unfortunately necessary because setting up the management + * route cannot be done from atomit context (SPI transfer takes a sleepable + * lock on the bus) + */ +static netdev_tx_t sja1105_port_deferred_xmit(struct dsa_switch *ds, int port, + struct sk_buff *skb) +{ + struct sja1105_private *priv = ds->priv; + struct sja1105_port *sp = &priv->ports[port]; + int slot = sp->mgmt_slot; + + /* The tragic fact about the switch having 4x2 slots for installing + * management routes is that all of them except one are actually + * useless. + * If 2 slots are simultaneously configured for two BPDUs sent to the + * same (multicast) DMAC but on different egress ports, the switch + * would confuse them and redirect first frame it receives on the CPU + * port towards the port configured on the numerically first slot + * (therefore wrong port), then second received frame on second slot + * (also wrong port). + * So for all practical purposes, there needs to be a lock that + * prevents that from happening. The slot used here is utterly useless + * (could have simply been 0 just as fine), but we are doing it + * nonetheless, in case a smarter idea ever comes up in the future. + */ + mutex_lock(&priv->mgmt_lock); + + sja1105_mgmt_xmit(ds, port, slot, skb); + + mutex_unlock(&priv->mgmt_lock); + return NETDEV_TX_OK; +} + +/* The MAXAGE setting belongs to the L2 Forwarding Parameters table, + * which cannot be reconfigured at runtime. So a switch reset is required. + */ +static int sja1105_set_ageing_time(struct dsa_switch *ds, + unsigned int ageing_time) +{ + struct sja1105_l2_lookup_params_entry *l2_lookup_params; + struct sja1105_private *priv = ds->priv; + struct sja1105_table *table; + unsigned int maxage; + + table = &priv->static_config.tables[BLK_IDX_L2_LOOKUP_PARAMS]; + l2_lookup_params = table->entries; + + maxage = SJA1105_AGEING_TIME_MS(ageing_time); + + if (l2_lookup_params->maxage == maxage) + return 0; + + l2_lookup_params->maxage = maxage; + + return sja1105_static_config_reload(priv); +} + +static const struct dsa_switch_ops sja1105_switch_ops = { + .get_tag_protocol = sja1105_get_tag_protocol, + .setup = sja1105_setup, + .adjust_link = sja1105_adjust_link, + .set_ageing_time = sja1105_set_ageing_time, + .phylink_validate = sja1105_phylink_validate, + .get_strings = sja1105_get_strings, + .get_ethtool_stats = sja1105_get_ethtool_stats, + .get_sset_count = sja1105_get_sset_count, + .port_fdb_dump = sja1105_fdb_dump, + .port_fdb_add = sja1105_fdb_add, + .port_fdb_del = sja1105_fdb_del, + .port_bridge_join = sja1105_bridge_join, + .port_bridge_leave = sja1105_bridge_leave, + .port_stp_state_set = sja1105_bridge_stp_state_set, + .port_vlan_prepare = sja1105_vlan_prepare, + .port_vlan_filtering = sja1105_vlan_filtering, + .port_vlan_add = sja1105_vlan_add, + .port_vlan_del = sja1105_vlan_del, + .port_mdb_prepare = sja1105_mdb_prepare, + .port_mdb_add = sja1105_mdb_add, + .port_mdb_del = sja1105_mdb_del, + .port_deferred_xmit = sja1105_port_deferred_xmit, +}; + +static int sja1105_check_device_id(struct sja1105_private *priv) +{ + const struct sja1105_regs *regs = priv->info->regs; + u8 prod_id[SJA1105_SIZE_DEVICE_ID] = {0}; + struct device *dev = &priv->spidev->dev; + u64 device_id; + u64 part_no; + int rc; + + rc = sja1105_spi_send_int(priv, SPI_READ, regs->device_id, + &device_id, SJA1105_SIZE_DEVICE_ID); + if (rc < 0) + return rc; + + if (device_id != priv->info->device_id) { + dev_err(dev, "Expected device ID 0x%llx but read 0x%llx\n", + priv->info->device_id, device_id); + return -ENODEV; + } + + rc = sja1105_spi_send_packed_buf(priv, SPI_READ, regs->prod_id, + prod_id, SJA1105_SIZE_DEVICE_ID); + if (rc < 0) + return rc; + + sja1105_unpack(prod_id, &part_no, 19, 4, SJA1105_SIZE_DEVICE_ID); + + if (part_no != priv->info->part_no) { + dev_err(dev, "Expected part number 0x%llx but read 0x%llx\n", + priv->info->part_no, part_no); + return -ENODEV; + } + + return 0; +} + +static int sja1105_probe(struct spi_device *spi) +{ + struct device *dev = &spi->dev; + struct sja1105_private *priv; + struct dsa_switch *ds; + int rc, i; + + if (!dev->of_node) { + dev_err(dev, "No DTS bindings for SJA1105 driver\n"); + return -EINVAL; + } + + priv = devm_kzalloc(dev, sizeof(struct sja1105_private), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + /* Configure the optional reset pin and bring up switch */ + priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(priv->reset_gpio)) + dev_dbg(dev, "reset-gpios not defined, ignoring\n"); + else + sja1105_hw_reset(priv->reset_gpio, 1, 1); + + /* Populate our driver private structure (priv) based on + * the device tree node that was probed (spi) + */ + priv->spidev = spi; + spi_set_drvdata(spi, priv); + + /* Configure the SPI bus */ + spi->bits_per_word = 8; + rc = spi_setup(spi); + if (rc < 0) { + dev_err(dev, "Could not init SPI\n"); + return rc; + } + + priv->info = of_device_get_match_data(dev); + + /* Detect hardware device */ + rc = sja1105_check_device_id(priv); + if (rc < 0) { + dev_err(dev, "Device ID check failed: %d\n", rc); + return rc; + } + + dev_info(dev, "Probed switch chip: %s\n", priv->info->name); + + ds = dsa_switch_alloc(dev, SJA1105_NUM_PORTS); + if (!ds) + return -ENOMEM; + + ds->ops = &sja1105_switch_ops; + ds->priv = priv; + priv->ds = ds; + + /* Connections between dsa_port and sja1105_port */ + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + struct sja1105_port *sp = &priv->ports[i]; + + ds->ports[i].priv = sp; + sp->dp = &ds->ports[i]; + } + mutex_init(&priv->mgmt_lock); + + return dsa_register_switch(priv->ds); +} + +static int sja1105_remove(struct spi_device *spi) +{ + struct sja1105_private *priv = spi_get_drvdata(spi); + + dsa_unregister_switch(priv->ds); + sja1105_static_config_free(&priv->static_config); + return 0; +} + +static const struct of_device_id sja1105_dt_ids[] = { + { .compatible = "nxp,sja1105e", .data = &sja1105e_info }, + { .compatible = "nxp,sja1105t", .data = &sja1105t_info }, + { .compatible = "nxp,sja1105p", .data = &sja1105p_info }, + { .compatible = "nxp,sja1105q", .data = &sja1105q_info }, + { .compatible = "nxp,sja1105r", .data = &sja1105r_info }, + { .compatible = "nxp,sja1105s", .data = &sja1105s_info }, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, sja1105_dt_ids); + +static struct spi_driver sja1105_driver = { + .driver = { + .name = "sja1105", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(sja1105_dt_ids), + }, + .probe = sja1105_probe, + .remove = sja1105_remove, +}; + +module_spi_driver(sja1105_driver); + +MODULE_AUTHOR("Vladimir Oltean <olteanv@gmail.com>"); +MODULE_AUTHOR("Georg Waibel <georg.waibel@sensor-technik.de>"); +MODULE_DESCRIPTION("SJA1105 Driver"); +MODULE_LICENSE("GPL v2"); |