diff options
Diffstat (limited to 'drivers/net/ethernet/intel/i40e/i40e_txrx.c')
| -rw-r--r-- | drivers/net/ethernet/intel/i40e/i40e_txrx.c | 542 |
1 files changed, 373 insertions, 169 deletions
diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c index e554aa6cf070..f174c72480ab 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c +++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c @@ -1,3 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0 /******************************************************************************* * * Intel Ethernet Controller XL710 Family Linux Driver @@ -335,7 +336,7 @@ static int i40e_add_del_fdir_tcpv4(struct i40e_vsi *vsi, if ((pf->flags & I40E_FLAG_FD_ATR_ENABLED) && I40E_DEBUG_FD & pf->hw.debug_mask) dev_info(&pf->pdev->dev, "Forcing ATR off, sideband rules for TCP/IPv4 flow being applied\n"); - pf->flags |= I40E_FLAG_FD_ATR_AUTO_DISABLED; + set_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state); } else { pf->fd_tcp4_filter_cnt--; } @@ -593,8 +594,14 @@ static void i40e_fd_handle_status(struct i40e_ring *rx_ring, pf->fd_atr_cnt = i40e_get_current_atr_cnt(pf); if ((rx_desc->wb.qword0.hi_dword.fd_id == 0) && - pf->flags & I40E_FLAG_FD_SB_AUTO_DISABLED) { - pf->flags |= I40E_FLAG_FD_ATR_AUTO_DISABLED; + test_bit(__I40E_FD_SB_AUTO_DISABLED, pf->state)) { + /* These set_bit() calls aren't atomic with the + * test_bit() here, but worse case we potentially + * disable ATR and queue a flush right after SB + * support is re-enabled. That shouldn't cause an + * issue in practice + */ + set_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state); set_bit(__I40E_FD_FLUSH_REQUESTED, pf->state); } @@ -607,11 +614,10 @@ static void i40e_fd_handle_status(struct i40e_ring *rx_ring, */ if (fcnt_prog >= (fcnt_avail - I40E_FDIR_BUFFER_FULL_MARGIN)) { if ((pf->flags & I40E_FLAG_FD_SB_ENABLED) && - !(pf->flags & I40E_FLAG_FD_SB_AUTO_DISABLED)) { - pf->flags |= I40E_FLAG_FD_SB_AUTO_DISABLED; + !test_and_set_bit(__I40E_FD_SB_AUTO_DISABLED, + pf->state)) if (I40E_DEBUG_FD & pf->hw.debug_mask) dev_warn(&pdev->dev, "FD filter space full, new ntuple rules will not be added\n"); - } } } else if (error == BIT(I40E_RX_PROG_STATUS_DESC_NO_FD_ENTRY_SHIFT)) { if (I40E_DEBUG_FD & pf->hw.debug_mask) @@ -708,16 +714,22 @@ void i40e_free_tx_resources(struct i40e_ring *tx_ring) /** * i40e_get_tx_pending - how many tx descriptors not processed * @tx_ring: the ring of descriptors + * @in_sw: use SW variables * * Since there is no access to the ring head register * in XL710, we need to use our local copies **/ -u32 i40e_get_tx_pending(struct i40e_ring *ring) +u32 i40e_get_tx_pending(struct i40e_ring *ring, bool in_sw) { u32 head, tail; - head = i40e_get_head(ring); - tail = readl(ring->tail); + if (!in_sw) { + head = i40e_get_head(ring); + tail = readl(ring->tail); + } else { + head = ring->next_to_clean; + tail = ring->next_to_use; + } if (head != tail) return (head < tail) ? @@ -774,7 +786,7 @@ void i40e_detect_recover_hung(struct i40e_vsi *vsi) */ smp_rmb(); tx_ring->tx_stats.prev_pkt_ctr = - i40e_get_tx_pending(tx_ring) ? packets : -1; + i40e_get_tx_pending(tx_ring, true) ? packets : -1; } } } @@ -898,7 +910,7 @@ static bool i40e_clean_tx_irq(struct i40e_vsi *vsi, * them to be written back in case we stay in NAPI. * In this mode on X722 we do not enable Interrupt. */ - unsigned int j = i40e_get_tx_pending(tx_ring); + unsigned int j = i40e_get_tx_pending(tx_ring, false); if (budget && ((j / WB_STRIDE) == 0) && (j > 0) && @@ -995,99 +1007,241 @@ void i40e_force_wb(struct i40e_vsi *vsi, struct i40e_q_vector *q_vector) } } +static inline bool i40e_container_is_rx(struct i40e_q_vector *q_vector, + struct i40e_ring_container *rc) +{ + return &q_vector->rx == rc; +} + +static inline unsigned int i40e_itr_divisor(struct i40e_q_vector *q_vector) +{ + unsigned int divisor; + + switch (q_vector->vsi->back->hw.phy.link_info.link_speed) { + case I40E_LINK_SPEED_40GB: + divisor = I40E_ITR_ADAPTIVE_MIN_INC * 1024; + break; + case I40E_LINK_SPEED_25GB: + case I40E_LINK_SPEED_20GB: + divisor = I40E_ITR_ADAPTIVE_MIN_INC * 512; + break; + default: + case I40E_LINK_SPEED_10GB: + divisor = I40E_ITR_ADAPTIVE_MIN_INC * 256; + break; + case I40E_LINK_SPEED_1GB: + case I40E_LINK_SPEED_100MB: + divisor = I40E_ITR_ADAPTIVE_MIN_INC * 32; + break; + } + + return divisor; +} + /** - * i40e_set_new_dynamic_itr - Find new ITR level + * i40e_update_itr - update the dynamic ITR value based on statistics + * @q_vector: structure containing interrupt and ring information * @rc: structure containing ring performance data * - * Returns true if ITR changed, false if not - * - * Stores a new ITR value based on packets and byte counts during - * the last interrupt. The advantage of per interrupt computation - * is faster updates and more accurate ITR for the current traffic - * pattern. Constants in this function were computed based on - * theoretical maximum wire speed and thresholds were set based on - * testing data as well as attempting to minimize response time + * Stores a new ITR value based on packets and byte + * counts during the last interrupt. The advantage of per interrupt + * computation is faster updates and more accurate ITR for the current + * traffic pattern. Constants in this function were computed + * based on theoretical maximum wire speed and thresholds were set based + * on testing data as well as attempting to minimize response time * while increasing bulk throughput. **/ -static bool i40e_set_new_dynamic_itr(struct i40e_ring_container *rc) +static void i40e_update_itr(struct i40e_q_vector *q_vector, + struct i40e_ring_container *rc) { - enum i40e_latency_range new_latency_range = rc->latency_range; - u32 new_itr = rc->itr; - int bytes_per_usec; - unsigned int usecs, estimated_usecs; + unsigned int avg_wire_size, packets, bytes, itr; + unsigned long next_update = jiffies; - if (rc->total_packets == 0 || !rc->itr) - return false; + /* If we don't have any rings just leave ourselves set for maximum + * possible latency so we take ourselves out of the equation. + */ + if (!rc->ring || !ITR_IS_DYNAMIC(rc->ring->itr_setting)) + return; - usecs = (rc->itr << 1) * ITR_COUNTDOWN_START; - bytes_per_usec = rc->total_bytes / usecs; + /* For Rx we want to push the delay up and default to low latency. + * for Tx we want to pull the delay down and default to high latency. + */ + itr = i40e_container_is_rx(q_vector, rc) ? + I40E_ITR_ADAPTIVE_MIN_USECS | I40E_ITR_ADAPTIVE_LATENCY : + I40E_ITR_ADAPTIVE_MAX_USECS | I40E_ITR_ADAPTIVE_LATENCY; + + /* If we didn't update within up to 1 - 2 jiffies we can assume + * that either packets are coming in so slow there hasn't been + * any work, or that there is so much work that NAPI is dealing + * with interrupt moderation and we don't need to do anything. + */ + if (time_after(next_update, rc->next_update)) + goto clear_counts; + + /* If itr_countdown is set it means we programmed an ITR within + * the last 4 interrupt cycles. This has a side effect of us + * potentially firing an early interrupt. In order to work around + * this we need to throw out any data received for a few + * interrupts following the update. + */ + if (q_vector->itr_countdown) { + itr = rc->target_itr; + goto clear_counts; + } - /* The calculations in this algorithm depend on interrupts actually - * firing at the ITR rate. This may not happen if the packet rate is - * really low, or if we've been napi polling. Check to make sure - * that's not the case before we continue. + packets = rc->total_packets; + bytes = rc->total_bytes; + + if (i40e_container_is_rx(q_vector, rc)) { + /* If Rx there are 1 to 4 packets and bytes are less than + * 9000 assume insufficient data to use bulk rate limiting + * approach unless Tx is already in bulk rate limiting. We + * are likely latency driven. + */ + if (packets && packets < 4 && bytes < 9000 && + (q_vector->tx.target_itr & I40E_ITR_ADAPTIVE_LATENCY)) { + itr = I40E_ITR_ADAPTIVE_LATENCY; + goto adjust_by_size; + } + } else if (packets < 4) { + /* If we have Tx and Rx ITR maxed and Tx ITR is running in + * bulk mode and we are receiving 4 or fewer packets just + * reset the ITR_ADAPTIVE_LATENCY bit for latency mode so + * that the Rx can relax. + */ + if (rc->target_itr == I40E_ITR_ADAPTIVE_MAX_USECS && + (q_vector->rx.target_itr & I40E_ITR_MASK) == + I40E_ITR_ADAPTIVE_MAX_USECS) + goto clear_counts; + } else if (packets > 32) { + /* If we have processed over 32 packets in a single interrupt + * for Tx assume we need to switch over to "bulk" mode. + */ + rc->target_itr &= ~I40E_ITR_ADAPTIVE_LATENCY; + } + + /* We have no packets to actually measure against. This means + * either one of the other queues on this vector is active or + * we are a Tx queue doing TSO with too high of an interrupt rate. + * + * Between 4 and 56 we can assume that our current interrupt delay + * is only slightly too low. As such we should increase it by a small + * fixed amount. */ - estimated_usecs = jiffies_to_usecs(jiffies - rc->last_itr_update); - if (estimated_usecs > usecs) { - new_latency_range = I40E_LOW_LATENCY; - goto reset_latency; + if (packets < 56) { + itr = rc->target_itr + I40E_ITR_ADAPTIVE_MIN_INC; + if ((itr & I40E_ITR_MASK) > I40E_ITR_ADAPTIVE_MAX_USECS) { + itr &= I40E_ITR_ADAPTIVE_LATENCY; + itr += I40E_ITR_ADAPTIVE_MAX_USECS; + } + goto clear_counts; } - /* simple throttlerate management - * 0-10MB/s lowest (50000 ints/s) - * 10-20MB/s low (20000 ints/s) - * 20-1249MB/s bulk (18000 ints/s) + if (packets <= 256) { + itr = min(q_vector->tx.current_itr, q_vector->rx.current_itr); + itr &= I40E_ITR_MASK; + + /* Between 56 and 112 is our "goldilocks" zone where we are + * working out "just right". Just report that our current + * ITR is good for us. + */ + if (packets <= 112) + goto clear_counts; + + /* If packet count is 128 or greater we are likely looking + * at a slight overrun of the delay we want. Try halving + * our delay to see if that will cut the number of packets + * in half per interrupt. + */ + itr /= 2; + itr &= I40E_ITR_MASK; + if (itr < I40E_ITR_ADAPTIVE_MIN_USECS) + itr = I40E_ITR_ADAPTIVE_MIN_USECS; + + goto clear_counts; + } + + /* The paths below assume we are dealing with a bulk ITR since + * number of packets is greater than 256. We are just going to have + * to compute a value and try to bring the count under control, + * though for smaller packet sizes there isn't much we can do as + * NAPI polling will likely be kicking in sooner rather than later. + */ + itr = I40E_ITR_ADAPTIVE_BULK; + +adjust_by_size: + /* If packet counts are 256 or greater we can assume we have a gross + * overestimation of what the rate should be. Instead of trying to fine + * tune it just use the formula below to try and dial in an exact value + * give the current packet size of the frame. + */ + avg_wire_size = bytes / packets; + + /* The following is a crude approximation of: + * wmem_default / (size + overhead) = desired_pkts_per_int + * rate / bits_per_byte / (size + ethernet overhead) = pkt_rate + * (desired_pkt_rate / pkt_rate) * usecs_per_sec = ITR value + * + * Assuming wmem_default is 212992 and overhead is 640 bytes per + * packet, (256 skb, 64 headroom, 320 shared info), we can reduce the + * formula down to * - * The math works out because the divisor is in 10^(-6) which - * turns the bytes/us input value into MB/s values, but - * make sure to use usecs, as the register values written - * are in 2 usec increments in the ITR registers, and make sure - * to use the smoothed values that the countdown timer gives us. + * (170 * (size + 24)) / (size + 640) = ITR + * + * We first do some math on the packet size and then finally bitshift + * by 8 after rounding up. We also have to account for PCIe link speed + * difference as ITR scales based on this. */ - switch (new_latency_range) { - case I40E_LOWEST_LATENCY: - if (bytes_per_usec > 10) - new_latency_range = I40E_LOW_LATENCY; - break; - case I40E_LOW_LATENCY: - if (bytes_per_usec > 20) - new_latency_range = I40E_BULK_LATENCY; - else if (bytes_per_usec <= 10) - new_latency_range = I40E_LOWEST_LATENCY; - break; - case I40E_BULK_LATENCY: - default: - if (bytes_per_usec <= 20) - new_latency_range = I40E_LOW_LATENCY; - break; + if (avg_wire_size <= 60) { + /* Start at 250k ints/sec */ + avg_wire_size = 4096; + } else if (avg_wire_size <= 380) { + /* 250K ints/sec to 60K ints/sec */ + avg_wire_size *= 40; + avg_wire_size += 1696; + } else if (avg_wire_size <= 1084) { + /* 60K ints/sec to 36K ints/sec */ + avg_wire_size *= 15; + avg_wire_size += 11452; + } else if (avg_wire_size <= 1980) { + /* 36K ints/sec to 30K ints/sec */ + avg_wire_size *= 5; + avg_wire_size += 22420; + } else { + /* plateau at a limit of 30K ints/sec */ + avg_wire_size = 32256; } -reset_latency: - rc->latency_range = new_latency_range; + /* If we are in low latency mode halve our delay which doubles the + * rate to somewhere between 100K to 16K ints/sec + */ + if (itr & I40E_ITR_ADAPTIVE_LATENCY) + avg_wire_size /= 2; - switch (new_latency_range) { - case I40E_LOWEST_LATENCY: - new_itr = I40E_ITR_50K; - break; - case I40E_LOW_LATENCY: - new_itr = I40E_ITR_20K; - break; - case I40E_BULK_LATENCY: - new_itr = I40E_ITR_18K; - break; - default: - break; + /* Resultant value is 256 times larger than it needs to be. This + * gives us room to adjust the value as needed to either increase + * or decrease the value based on link speeds of 10G, 2.5G, 1G, etc. + * + * Use addition as we have already recorded the new latency flag + * for the ITR value. + */ + itr += DIV_ROUND_UP(avg_wire_size, i40e_itr_divisor(q_vector)) * + I40E_ITR_ADAPTIVE_MIN_INC; + + if ((itr & I40E_ITR_MASK) > I40E_ITR_ADAPTIVE_MAX_USECS) { + itr &= I40E_ITR_ADAPTIVE_LATENCY; + itr += I40E_ITR_ADAPTIVE_MAX_USECS; } +clear_counts: + /* write back value */ + rc->target_itr = itr; + + /* next update should occur within next jiffy */ + rc->next_update = next_update + 1; + rc->total_bytes = 0; rc->total_packets = 0; - rc->last_itr_update = jiffies; - - if (new_itr != rc->itr) { - rc->itr = new_itr; - return true; - } - return false; } /** @@ -1434,9 +1588,8 @@ static bool i40e_alloc_mapped_page(struct i40e_ring *rx_ring, bi->dma = dma; bi->page = page; bi->page_offset = i40e_rx_offset(rx_ring); - - /* initialize pagecnt_bias to 1 representing we fully own page */ - bi->pagecnt_bias = 1; + page_ref_add(page, USHRT_MAX - 1); + bi->pagecnt_bias = USHRT_MAX; return true; } @@ -1802,8 +1955,8 @@ static bool i40e_can_reuse_rx_page(struct i40e_rx_buffer *rx_buffer) * the pagecnt_bias and page count so that we fully restock the * number of references the driver holds. */ - if (unlikely(!pagecnt_bias)) { - page_ref_add(page, USHRT_MAX); + if (unlikely(pagecnt_bias == 1)) { + page_ref_add(page, USHRT_MAX - 1); rx_buffer->pagecnt_bias = USHRT_MAX; } @@ -1991,7 +2144,7 @@ static struct sk_buff *i40e_build_skb(struct i40e_ring *rx_ring, * @rx_buffer: rx buffer to pull data from * * This function will clean up the contents of the rx_buffer. It will - * either recycle the bufer or unmap it and free the associated resources. + * either recycle the buffer or unmap it and free the associated resources. */ static void i40e_put_rx_buffer(struct i40e_ring *rx_ring, struct i40e_rx_buffer *rx_buffer) @@ -2061,7 +2214,7 @@ static int i40e_xmit_xdp_ring(struct xdp_buff *xdp, static struct sk_buff *i40e_run_xdp(struct i40e_ring *rx_ring, struct xdp_buff *xdp) { - int result = I40E_XDP_PASS; + int err, result = I40E_XDP_PASS; struct i40e_ring *xdp_ring; struct bpf_prog *xdp_prog; u32 act; @@ -2080,6 +2233,10 @@ static struct sk_buff *i40e_run_xdp(struct i40e_ring *rx_ring, xdp_ring = rx_ring->vsi->xdp_rings[rx_ring->queue_index]; result = i40e_xmit_xdp_ring(xdp, xdp_ring); break; + case XDP_REDIRECT: + err = xdp_do_redirect(rx_ring->netdev, xdp, xdp_prog); + result = !err ? I40E_XDP_TX : I40E_XDP_CONSUMED; + break; default: bpf_warn_invalid_xdp_action(act); case XDP_ABORTED: @@ -2115,6 +2272,15 @@ static void i40e_rx_buffer_flip(struct i40e_ring *rx_ring, #endif } +static inline void i40e_xdp_ring_update_tail(struct i40e_ring *xdp_ring) +{ + /* Force memory writes to complete before letting h/w + * know there are new descriptors to fetch. + */ + wmb(); + writel_relaxed(xdp_ring->next_to_use, xdp_ring->tail); +} + /** * i40e_clean_rx_irq - Clean completed descriptors from Rx ring - bounce buf * @rx_ring: rx descriptor ring to transact packets on @@ -2249,16 +2415,11 @@ static int i40e_clean_rx_irq(struct i40e_ring *rx_ring, int budget) } if (xdp_xmit) { - struct i40e_ring *xdp_ring; + struct i40e_ring *xdp_ring = + rx_ring->vsi->xdp_rings[rx_ring->queue_index]; - xdp_ring = rx_ring->vsi->xdp_rings[rx_ring->queue_index]; - - /* Force memory writes to complete before letting h/w - * know there are new descriptors to fetch. - */ - wmb(); - - writel(xdp_ring->next_to_use, xdp_ring->tail); + i40e_xdp_ring_update_tail(xdp_ring); + xdp_do_flush_map(); } rx_ring->skb = skb; @@ -2274,29 +2435,45 @@ static int i40e_clean_rx_irq(struct i40e_ring *rx_ring, int budget) return failure ? budget : (int)total_rx_packets; } -static u32 i40e_buildreg_itr(const int type, const u16 itr) +static inline u32 i40e_buildreg_itr(const int type, u16 itr) { u32 val; + /* We don't bother with setting the CLEARPBA bit as the data sheet + * points out doing so is "meaningless since it was already + * auto-cleared". The auto-clearing happens when the interrupt is + * asserted. + * + * Hardware errata 28 for also indicates that writing to a + * xxINT_DYN_CTLx CSR with INTENA_MSK (bit 31) set to 0 will clear + * an event in the PBA anyway so we need to rely on the automask + * to hold pending events for us until the interrupt is re-enabled + * + * The itr value is reported in microseconds, and the register + * value is recorded in 2 microsecond units. For this reason we + * only need to shift by the interval shift - 1 instead of the + * full value. + */ + itr &= I40E_ITR_MASK; + val = I40E_PFINT_DYN_CTLN_INTENA_MASK | - I40E_PFINT_DYN_CTLN_CLEARPBA_MASK | (type << I40E_PFINT_DYN_CTLN_ITR_INDX_SHIFT) | - (itr << I40E_PFINT_DYN_CTLN_INTERVAL_SHIFT); + (itr << (I40E_PFINT_DYN_CTLN_INTERVAL_SHIFT - 1)); return val; } /* a small macro to shorten up some long lines */ #define INTREG I40E_PFINT_DYN_CTLN -static inline int get_rx_itr(struct i40e_vsi *vsi, int idx) -{ - return vsi->rx_rings[idx]->rx_itr_setting; -} -static inline int get_tx_itr(struct i40e_vsi *vsi, int idx) -{ - return vsi->tx_rings[idx]->tx_itr_setting; -} +/* The act of updating the ITR will cause it to immediately trigger. In order + * to prevent this from throwing off adaptive update statistics we defer the + * update so that it can only happen so often. So after either Tx or Rx are + * updated we make the adaptive scheme wait until either the ITR completely + * expires via the next_update expiration or we have been through at least + * 3 interrupts. + */ +#define ITR_COUNTDOWN_START 3 /** * i40e_update_enable_itr - Update itr and re-enable MSIX interrupt @@ -2308,10 +2485,7 @@ static inline void i40e_update_enable_itr(struct i40e_vsi *vsi, struct i40e_q_vector *q_vector) { struct i40e_hw *hw = &vsi->back->hw; - bool rx = false, tx = false; - u32 rxval, txval; - int idx = q_vector->v_idx; - int rx_itr_setting, tx_itr_setting; + u32 intval; /* If we don't have MSIX, then we only need to re-enable icr0 */ if (!(vsi->back->flags & I40E_FLAG_MSIX_ENABLED)) { @@ -2319,65 +2493,49 @@ static inline void i40e_update_enable_itr(struct i40e_vsi *vsi, return; } - /* avoid dynamic calculation if in countdown mode OR if - * all dynamic is disabled - */ - rxval = txval = i40e_buildreg_itr(I40E_ITR_NONE, 0); - - rx_itr_setting = get_rx_itr(vsi, idx); - tx_itr_setting = get_tx_itr(vsi, idx); - - if (q_vector->itr_countdown > 0 || - (!ITR_IS_DYNAMIC(rx_itr_setting) && - !ITR_IS_DYNAMIC(tx_itr_setting))) { - goto enable_int; - } - - if (ITR_IS_DYNAMIC(rx_itr_setting)) { - rx = i40e_set_new_dynamic_itr(&q_vector->rx); - rxval = i40e_buildreg_itr(I40E_RX_ITR, q_vector->rx.itr); - } - - if (ITR_IS_DYNAMIC(tx_itr_setting)) { - tx = i40e_set_new_dynamic_itr(&q_vector->tx); - txval = i40e_buildreg_itr(I40E_TX_ITR, q_vector->tx.itr); - } - - if (rx || tx) { - /* get the higher of the two ITR adjustments and - * use the same value for both ITR registers - * when in adaptive mode (Rx and/or Tx) - */ - u16 itr = max(q_vector->tx.itr, q_vector->rx.itr); - - q_vector->tx.itr = q_vector->rx.itr = itr; - txval = i40e_buildreg_itr(I40E_TX_ITR, itr); - tx = true; - rxval = i40e_buildreg_itr(I40E_RX_ITR, itr); - rx = true; - } + /* These will do nothing if dynamic updates are not enabled */ + i40e_update_itr(q_vector, &q_vector->tx); + i40e_update_itr(q_vector, &q_vector->rx); - /* only need to enable the interrupt once, but need - * to possibly update both ITR values + /* This block of logic allows us to get away with only updating + * one ITR value with each interrupt. The idea is to perform a + * pseudo-lazy update with the following criteria. + * + * 1. Rx is given higher priority than Tx if both are in same state + * 2. If we must reduce an ITR that is given highest priority. + * 3. We then give priority to increasing ITR based on amount. */ - if (rx) { - /* set the INTENA_MSK_MASK so that this first write - * won't actually enable the interrupt, instead just - * updating the ITR (it's bit 31 PF and VF) + if (q_vector->rx.target_itr < q_vector->rx.current_itr) { + /* Rx ITR needs to be reduced, this is highest priority */ + intval = i40e_buildreg_itr(I40E_RX_ITR, + q_vector->rx.target_itr); + q_vector->rx.current_itr = q_vector->rx.target_itr; + q_vector->itr_countdown = ITR_COUNTDOWN_START; + } else if ((q_vector->tx.target_itr < q_vector->tx.current_itr) || + ((q_vector->rx.target_itr - q_vector->rx.current_itr) < + (q_vector->tx.target_itr - q_vector->tx.current_itr))) { + /* Tx ITR needs to be reduced, this is second priority + * Tx ITR needs to be increased more than Rx, fourth priority */ - rxval |= BIT(31); - /* don't check _DOWN because interrupt isn't being enabled */ - wr32(hw, INTREG(q_vector->reg_idx), rxval); + intval = i40e_buildreg_itr(I40E_TX_ITR, + q_vector->tx.target_itr); + q_vector->tx.current_itr = q_vector->tx.target_itr; + q_vector->itr_countdown = ITR_COUNTDOWN_START; + } else if (q_vector->rx.current_itr != q_vector->rx.target_itr) { + /* Rx ITR needs to be increased, third priority */ + intval = i40e_buildreg_itr(I40E_RX_ITR, + q_vector->rx.target_itr); + q_vector->rx.current_itr = q_vector->rx.target_itr; + q_vector->itr_countdown = ITR_COUNTDOWN_START; + } else { + /* No ITR update, lowest priority */ + intval = i40e_buildreg_itr(I40E_ITR_NONE, 0); + if (q_vector->itr_countdown) + q_vector->itr_countdown--; } -enable_int: if (!test_bit(__I40E_VSI_DOWN, vsi->state)) - wr32(hw, INTREG(q_vector->reg_idx), txval); - - if (q_vector->itr_countdown) - q_vector->itr_countdown--; - else - q_vector->itr_countdown = ITR_COUNTDOWN_START; + wr32(hw, INTREG(q_vector->reg_idx), intval); } /** @@ -2501,7 +2659,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb, if (!(pf->flags & I40E_FLAG_FD_ATR_ENABLED)) return; - if (pf->flags & I40E_FLAG_FD_ATR_AUTO_DISABLED) + if (test_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state)) return; /* if sampling is disabled do nothing */ @@ -2541,7 +2699,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb, th = (struct tcphdr *)(hdr.network + hlen); /* Due to lack of space, no more new filters can be programmed */ - if (th->syn && (pf->flags & I40E_FLAG_FD_ATR_AUTO_DISABLED)) + if (th->syn && test_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state)) return; if (pf->flags & I40E_FLAG_HW_ATR_EVICT_ENABLED) { /* HW ATR eviction will take care of removing filters on FIN @@ -3509,3 +3667,49 @@ netdev_tx_t i40e_lan_xmit_frame(struct sk_buff *skb, struct net_device *netdev) return i40e_xmit_frame_ring(skb, tx_ring); } + +/** + * i40e_xdp_xmit - Implements ndo_xdp_xmit + * @dev: netdev + * @xdp: XDP buffer + * + * Returns Zero if sent, else an error code + **/ +int i40e_xdp_xmit(struct net_device *dev, struct xdp_buff *xdp) +{ + struct i40e_netdev_priv *np = netdev_priv(dev); + unsigned int queue_index = smp_processor_id(); + struct i40e_vsi *vsi = np->vsi; + int err; + + if (test_bit(__I40E_VSI_DOWN, vsi->state)) + return -ENETDOWN; + + if (!i40e_enabled_xdp_vsi(vsi) || queue_index >= vsi->num_queue_pairs) + return -ENXIO; + + err = i40e_xmit_xdp_ring(xdp, vsi->xdp_rings[queue_index]); + if (err != I40E_XDP_TX) + return -ENOSPC; + + return 0; +} + +/** + * i40e_xdp_flush - Implements ndo_xdp_flush + * @dev: netdev + **/ +void i40e_xdp_flush(struct net_device *dev) +{ + struct i40e_netdev_priv *np = netdev_priv(dev); + unsigned int queue_index = smp_processor_id(); + struct i40e_vsi *vsi = np->vsi; + + if (test_bit(__I40E_VSI_DOWN, vsi->state)) + return; + + if (!i40e_enabled_xdp_vsi(vsi) || queue_index >= vsi->num_queue_pairs) + return; + + i40e_xdp_ring_update_tail(vsi->xdp_rings[queue_index]); +} |