diff options
Diffstat (limited to 'include/linux')
| -rw-r--r-- | include/linux/amba/pl022.h | 10 | ||||
| -rw-r--r-- | include/linux/parport.h | 12 | ||||
| -rw-r--r-- | include/linux/spi/spi.h | 20 |
3 files changed, 14 insertions, 28 deletions
diff --git a/include/linux/amba/pl022.h b/include/linux/amba/pl022.h index 131b27c97209..9bf58aac0df2 100644 --- a/include/linux/amba/pl022.h +++ b/include/linux/amba/pl022.h @@ -223,10 +223,6 @@ struct dma_chan; /** * struct pl022_ssp_master - device.platform_data for SPI controller devices. * @bus_id: identifier for this bus - * @num_chipselect: chipselects are used to distinguish individual - * SPI slaves, and are numbered from zero to num_chipselects - 1. - * each slave has a chipselect signal, but it's common that not - * every chipselect is connected to a slave. * @enable_dma: if true enables DMA driven transfers. * @dma_rx_param: parameter to locate an RX DMA channel. * @dma_tx_param: parameter to locate a TX DMA channel. @@ -235,18 +231,15 @@ struct dma_chan; * indicates no delay and the device will be suspended immediately. * @rt: indicates the controller should run the message pump with realtime * priority to minimise the transfer latency on the bus. - * @chipselects: list of <num_chipselects> chip select gpios */ struct pl022_ssp_controller { u16 bus_id; - u8 num_chipselect; u8 enable_dma:1; bool (*dma_filter)(struct dma_chan *chan, void *filter_param); void *dma_rx_param; void *dma_tx_param; int autosuspend_delay; bool rt; - int *chipselects; }; /** @@ -265,8 +258,6 @@ struct pl022_ssp_controller { * @duplex: Microwire interface: Full/Half duplex * @clkdelay: on the PL023 variant, the delay in feeback clock cycles * before sampling the incoming line - * @cs_control: function pointer to board-specific function to - * assert/deassert I/O port to control HW generation of devices chip-select. */ struct pl022_config_chip { enum ssp_interface iface; @@ -280,7 +271,6 @@ struct pl022_config_chip { enum ssp_microwire_wait_state wait_state; enum ssp_duplex duplex; enum ssp_clkdelay clkdelay; - void (*cs_control) (u32 control); }; #endif /* _SSP_PL022_H */ diff --git a/include/linux/parport.h b/include/linux/parport.h index f981f794c850..1c16ffb8b908 100644 --- a/include/linux/parport.h +++ b/include/linux/parport.h @@ -332,9 +332,19 @@ int __must_check __parport_register_driver(struct parport_driver *, __parport_register_driver(driver, THIS_MODULE, KBUILD_MODNAME) /* Unregister a high-level driver. */ -extern void parport_unregister_driver (struct parport_driver *); void parport_unregister_driver(struct parport_driver *); +/** + * module_parport_driver() - Helper macro for registering a modular parport driver + * @__parport_driver: struct parport_driver to be used + * + * Helper macro for parport drivers which do not do anything special in module + * init and exit. This eliminates a lot of boilerplate. Each module may only + * use this macro once, and calling it replaces module_init() and module_exit(). + */ +#define module_parport_driver(__parport_driver) \ + module_driver(__parport_driver, parport_register_driver, parport_unregister_driver) + /* If parport_register_driver doesn't fit your needs, perhaps * parport_find_xxx does. */ extern struct parport *parport_find_number (int); diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 643139b1eafe..360a3bc767ca 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -19,7 +19,7 @@ #include <uapi/linux/spi/spi.h> struct dma_chan; -struct property_entry; +struct software_node; struct spi_controller; struct spi_transfer; struct spi_controller_mem_ops; @@ -247,7 +247,6 @@ static inline void *spi_get_drvdata(struct spi_device *spi) } struct spi_message; -struct spi_transfer; /** * struct spi_driver - Host side "protocol" driver @@ -835,9 +834,6 @@ extern void spi_res_release(struct spi_controller *ctlr, * @delay: delay to be introduced after this transfer before * (optionally) changing the chipselect status, then starting * the next transfer or completing this @spi_message. - * @delay_usecs: microseconds to delay after this transfer before - * (optionally) changing the chipselect status, then starting - * the next transfer or completing this @spi_message. * @word_delay: inter word delay to be introduced after each word size * (set by bits_per_word) transmission. * @effective_speed_hz: the effective SCK-speed that was used to @@ -949,7 +945,6 @@ struct spi_transfer { #define SPI_NBITS_DUAL 0x02 /* 2bits transfer */ #define SPI_NBITS_QUAD 0x04 /* 4bits transfer */ u8 bits_per_word; - u16 delay_usecs; struct spi_delay delay; struct spi_delay cs_change_delay; struct spi_delay word_delay; @@ -1063,14 +1058,6 @@ spi_transfer_del(struct spi_transfer *t) static inline int spi_transfer_delay_exec(struct spi_transfer *t) { - struct spi_delay d; - - if (t->delay_usecs) { - d.value = t->delay_usecs; - d.unit = SPI_DELAY_UNIT_USECS; - return spi_delay_exec(&d, NULL); - } - return spi_delay_exec(&t->delay, t); } @@ -1412,7 +1399,7 @@ static inline ssize_t spi_w8r16be(struct spi_device *spi, u8 cmd) * @modalias: Initializes spi_device.modalias; identifies the driver. * @platform_data: Initializes spi_device.platform_data; the particular * data stored there is driver-specific. - * @properties: Additional device properties for the device. + * @swnode: Software node for the device. * @controller_data: Initializes spi_device.controller_data; some * controllers need hints about hardware setup, e.g. for DMA. * @irq: Initializes spi_device.irq; depends on how the board is wired. @@ -1445,12 +1432,11 @@ struct spi_board_info { * * platform_data goes to spi_device.dev.platform_data, * controller_data goes to spi_device.controller_data, - * device properties are copied and attached to spi_device, * irq is copied too */ char modalias[SPI_NAME_SIZE]; const void *platform_data; - const struct property_entry *properties; + const struct software_node *swnode; void *controller_data; int irq; |