| Age | Commit message (Collapse) | Author |
|---|
|
Add support for signed mod instructions.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Add support for signed div instructions.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Add support for 32-bit offset jmp instruction. Currently, we use b
instruction which supports range within ±128MB for such jumps. This
should be large enough for BPF progs.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Add support for unconditional bswap instruction. Since LoongArch is
always little-endian, just treat unconditional bswap the same as big-
endian conversion.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Add support for sign-extension mov instructions.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Add support for sign-extension load instructions.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
This patch adds more instruction opcodes and their corresponding emit_*
helpers which will be used in later patches.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
rcutree_report_cpu_starting() must be called before cpu_probe() to avoid
the following lockdep splat that triggered by calling __alloc_pages() when
CONFIG_PROVE_RCU_LIST=y:
=============================
WARNING: suspicious RCU usage
6.6.0+ #980 Not tainted
-----------------------------
kernel/locking/lockdep.c:3761 RCU-list traversed in non-reader section!!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 1, debug_locks = 1
1 lock held by swapper/1/0:
#0: 900000000c82ef98 (&pcp->lock){+.+.}-{2:2}, at: get_page_from_freelist+0x894/0x1790
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.6.0+ #980
Stack : 0000000000000001 9000000004f79508 9000000004893670 9000000100310000
90000001003137d0 0000000000000000 90000001003137d8 9000000004f79508
0000000000000000 0000000000000001 0000000000000000 90000000048a3384
203a656d616e2065 ca43677b3687e616 90000001002c3480 0000000000000008
000000000000009d 0000000000000000 0000000000000001 80000000ffffe0b8
000000000000000d 0000000000000033 0000000007ec0000 13bbf50562dad831
9000000005140748 0000000000000000 9000000004f79508 0000000000000004
0000000000000000 9000000005140748 90000001002bad40 0000000000000000
90000001002ba400 0000000000000000 9000000003573ec8 0000000000000000
00000000000000b0 0000000000000004 0000000000000000 0000000000070000
...
Call Trace:
[<9000000003573ec8>] show_stack+0x38/0x150
[<9000000004893670>] dump_stack_lvl+0x74/0xa8
[<900000000360d2bc>] lockdep_rcu_suspicious+0x14c/0x190
[<900000000361235c>] __lock_acquire+0xd0c/0x2740
[<90000000036146f4>] lock_acquire+0x104/0x2c0
[<90000000048a955c>] _raw_spin_lock_irqsave+0x5c/0x90
[<900000000381cd5c>] rmqueue_bulk+0x6c/0x950
[<900000000381fc0c>] get_page_from_freelist+0xd4c/0x1790
[<9000000003821c6c>] __alloc_pages+0x1bc/0x3e0
[<9000000003583b40>] tlb_init+0x150/0x2a0
[<90000000035742a0>] per_cpu_trap_init+0xf0/0x110
[<90000000035712fc>] cpu_probe+0x3dc/0x7a0
[<900000000357ed20>] start_secondary+0x40/0xb0
[<9000000004897138>] smpboot_entry+0x54/0x58
raw_smp_processor_id() is required in order to avoid calling into lockdep
before RCU has declared the CPU to be watched for readers.
See also commit 29368e093921 ("x86/smpboot: Move rcu_cpu_starting() earlier"),
commit de5d9dae150c ("s390/smp: move rcu_cpu_starting() earlier") and commit
99f070b62322 ("powerpc/smp: Call rcu_cpu_starting() earlier").
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
This patch relaxes the implementation while satisfying the memory ordering
requirements for atomic operations, which will help improve performance on
LA664+.
Unixbench with full threads (8)
before after
Dhrystone 2 using register variables 203910714.2 203909539.8 0.00%
Double-Precision Whetstone 37930.9 37931 0.00%
Execl Throughput 29431.5 29545.8 0.39%
File Copy 1024 bufsize 2000 maxblocks 6645759.5 6676320 0.46%
File Copy 256 bufsize 500 maxblocks 2138772.4 2144182.4 0.25%
File Copy 4096 bufsize 8000 maxblocks 11640698.4 11602703 -0.33%
Pipe Throughput 8849077.7 8917009.4 0.77%
Pipe-based Context Switching 1255108.5 1287277.3 2.56%
Process Creation 50825.9 50442.1 -0.76%
Shell Scripts (1 concurrent) 25795.8 25942.3 0.57%
Shell Scripts (8 concurrent) 3812.6 3835.2 0.59%
System Call Overhead 9248212.6 9353348.6 1.14%
=======
System Benchmarks Index Score 8076.6 8114.4 0.47%
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
A recent change to the optimization pipeline in LLVM reveals some
fragility around the inlining of LoongArch's __percpu functions, which
manifests as a BUILD_BUG() failure:
In file included from kernel/sched/build_policy.c:17:
In file included from include/linux/sched/cputime.h:5:
In file included from include/linux/sched/signal.h:5:
In file included from include/linux/rculist.h:11:
In file included from include/linux/rcupdate.h:26:
In file included from include/linux/irqflags.h:18:
arch/loongarch/include/asm/percpu.h:97:3: error: call to '__compiletime_assert_51' declared with 'error' attribute: BUILD_BUG failed
97 | BUILD_BUG();
| ^
include/linux/build_bug.h:59:21: note: expanded from macro 'BUILD_BUG'
59 | #define BUILD_BUG() BUILD_BUG_ON_MSG(1, "BUILD_BUG failed")
| ^
include/linux/build_bug.h:39:37: note: expanded from macro 'BUILD_BUG_ON_MSG'
39 | #define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
| ^
include/linux/compiler_types.h:425:2: note: expanded from macro 'compiletime_assert'
425 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| ^
include/linux/compiler_types.h:413:2: note: expanded from macro '_compiletime_assert'
413 | __compiletime_assert(condition, msg, prefix, suffix)
| ^
include/linux/compiler_types.h:406:4: note: expanded from macro '__compiletime_assert'
406 | prefix ## suffix(); \
| ^
<scratch space>:86:1: note: expanded from here
86 | __compiletime_assert_51
| ^
1 error generated.
If these functions are not inlined (which the compiler is free to do
even with functions marked with the standard 'inline' keyword), the
BUILD_BUG() in the default case cannot be eliminated since the compiler
cannot prove it is never used, resulting in a build failure due to the
error attribute.
Mark these functions as __always_inline to guarantee inlining so that
the BUILD_BUG() only triggers when the default case genuinely cannot be
eliminated due to an unexpected size.
Cc: <stable@vger.kernel.org>
Closes: https://github.com/ClangBuiltLinux/linux/issues/1955
Fixes: 46859ac8af52 ("LoongArch: Add multi-processor (SMP) support")
Link: https://github.com/llvm/llvm-project/commit/1a2e77cf9e11dbf56b5720c607313a566eebb16e
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The distance between vmlinux and the module is too far so that PC-REL
cannot be accessed directly, only GOT.
When compiling module with GCC, the option `-mdirect-extern-access` is
disabled by default. The Clang option `-fdirect-access-external-data` is
enabled by default, so it needs to be explicitly disabled.
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Since commit 4e90d0522a688371402c ("riscv: support PREEMPT_DYNAMIC with
static keys"), the infrastructure is complete and we can simply select
HAVE_PREEMPT_DYNAMIC_KEY to enable PREEMPT_DYNAMIC on LoongArch because
we already support static keys.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
LoongArch architecture changes for 6.7 (BPF CPU v4 support) depend on
the bpf changes to fix conflictions in selftests and work, so merge them
to create a base.
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 fixes from Ingo Molnar:
- Fix a possible CPU hotplug deadlock bug caused by the new TSC
synchronization code
- Fix a legacy PIC discovery bug that results in device troubles on
affected systems, such as non-working keybards, etc
- Add a new Intel CPU model number to <asm/intel-family.h>
* tag 'x86-urgent-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Defer marking TSC unstable to a worker
x86/i8259: Skip probing when ACPI/MADT advertises PCAT compatibility
x86/cpu: Add model number for Intel Arrow Lake mobile processor
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"Restore unintentionally lost quirk settings in the GIC irqchip driver,
which broke certain devices"
* tag 'irq-urgent-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Don't override quirk settings with default values
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf event fix from Ingo Molnar:
"Fix a potential NULL dereference bug"
* tag 'perf-urgent-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix potential NULL deref
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fixes from Masami Hiramatsu:
- tracing/kprobes: Fix kernel-doc warnings for the variable length
arguments
- tracing/kprobes: Fix to count the symbols in modules even if the
module name is not specified so that user can probe the symbols in
the modules without module name
* tag 'probes-fixes-v6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/kprobes: Fix symbol counting logic by looking at modules as well
tracing/kprobes: Fix the description of variable length arguments
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fix from Christoph Hellwig:
- reduce the initialy dynamic swiotlb size to remove an annoying but
harmless warning from the page allocator (Petr Tesarik)
* tag 'dma-mapping-6.6-2023-10-28' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: do not try to allocate a TLB bigger than MAX_ORDER pages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some very small driver fixes for 6.6-final that have shown up
in the past two weeks. Included in here are:
- tiny fastrpc bugfixes for reported errors
- nvmem register fixes
- iio driver fixes for some reported problems
- fpga test fix
- MAINTAINERS file update for fpga
All of these have been in linux-next this week with no reported
problems"
* tag 'char-misc-6.6-final' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fpga: Fix memory leak for fpga_region_test_class_find()
fpga: m10bmc-sec: Change contact for secure update driver
fpga: disable KUnit test suites when module support is enabled
iio: afe: rescale: Accept only offset channels
nvmem: imx: correct nregs for i.MX6ULL
nvmem: imx: correct nregs for i.MX6UL
nvmem: imx: correct nregs for i.MX6SLL
misc: fastrpc: Unmap only if buffer is unmapped from DSP
misc: fastrpc: Clean buffers on remote invocation failures
misc: fastrpc: Free DMA handles for RPC calls with no arguments
misc: fastrpc: Reset metadata buffer to avoid incorrect free
iio: exynos-adc: request second interupt only when touchscreen mode is used
iio: adc: xilinx-xadc: Correct temperature offset/scale for UltraScale
iio: adc: xilinx-xadc: Don't clobber preset voltage/temperature thresholds
dt-bindings: iio: add missing reset-gpios constrain
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Bugfixes for Axxia when it is a target and for PEC handling of
stm32f7.
Plus, fix an OF node leak pattern in the mux subsystem"
* tag 'i2c-for-6.6-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32f7: Fix PEC handling in case of SMBUS transfers
i2c: muxes: i2c-mux-gpmux: Use of_get_i2c_adapter_by_node()
i2c: muxes: i2c-demux-pinctrl: Use of_get_i2c_adapter_by_node()
i2c: muxes: i2c-mux-pinctrl: Use of_get_i2c_adapter_by_node()
i2c: aspeed: Fix i2c bus hang in slave read
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Three fixes, one for the clk framework and two for clk drivers:
- Avoid an oops in possible_parent_show() by checking for no parent
properly when a DT index based lookup is used
- Handle errors returned from divider_ro_round_rate() in
clk_stm32_composite_determine_rate()
- Fix clk_ops::determine_rate() implementation of socfpga's
gateclk_ops that was ruining uart output because the divider
was forgotten about"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: stm32: Fix a signedness issue in clk_stm32_composite_determine_rate()
clk: Sanitize possible_parent_show to Handle Return Value of of_clk_get_parent_name
clk: socfpga: gate: Account for the divider in determine_rate
|
|
Pull misc filesystem fixes from Al Viro:
"Assorted fixes all over the place: literally nothing in common, could
have been three separate pull requests.
All are simple regression fixes, but not for anything from this cycle"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ceph_wait_on_conflict_unlink(): grab reference before dropping ->d_lock
io_uring: kiocb_done() should *not* trust ->ki_pos if ->{read,write}_iter() failed
sparc32: fix a braino in fault handling in csum_and_copy_..._user()
|
|
Recent changes to count number of matching symbols when creating
a kprobe event failed to take into account kernel modules. As such, it
breaks kprobes on kernel module symbols, by assuming there is no match.
Fix this my calling module_kallsyms_on_each_symbol() in addition to
kallsyms_on_each_match_symbol() to perform a proper counting.
Link: https://lore.kernel.org/all/20231027233126.2073148-1-andrii@kernel.org/
Cc: Francis Laniel <flaniel@linux.microsoft.com>
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Fixes: b022f0c7e404 ("tracing/kprobes: Return EADDRNOTAVAIL when func matches several symbols")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
Use of dget() after we'd dropped ->d_lock is too late - dentry might
be gone by that point.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
failed
->ki_pos value is unreliable in such cases. For an obvious example,
consider O_DSYNC write - we feed the data to page cache and start IO,
then we make sure it's completed. Update of ->ki_pos is dealt with
by the first part; failure in the second ends up with negative value
returned _and_ ->ki_pos left advanced as if sync had been successful.
In the same situation write(2) does not advance the file position
at all.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull io_uring fixes from Jens Axboe:
"Fix for an issue reported where reading fdinfo could find a NULL
thread as we didn't properly synchronize, and then a disable for the
IOCB_DIO_CALLER_COMP optimization as a recent reported highlighted how
that could lead to deadlocks if the task issued async O_DIRECT writes
and then proceeded to do sync fallocate() calls"
* tag 'io_uring-6.6-2023-10-27' of git://git.kernel.dk/linux:
io_uring/rw: disable IOCB_DIO_CALLER_COMP
io_uring/fdinfo: lock SQ thread while retrieving thread cpu/pid
|
|
Fault handler used to make non-trivial calls, so it needed
to set a stack frame up. Used to be
save ... - grab a stack frame, old %o... become %i...
....
ret - go back to address originally in %o7, currently %i7
restore - switch to previous stack frame, in delay slot
Non-trivial calls had been gone since ab5e8b331244 and that code should
have become
retl - go back to address in %o7
clr %o0 - have return value set to 0
What it had become instead was
ret - go back to address in %i7 - return address of *caller*
clr %o0 - have return value set to 0
which is not good, to put it mildly - we forcibly return 0 from
csum_and_copy_{from,to}_iter() (which is what the call of that
thing had been inlined into) and do that without dropping the
stack frame of said csum_and_copy_..._iter(). Confuses the
hell out of the caller of csum_and_copy_..._iter(), obviously...
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: ab5e8b331244 "sparc32: propagate the calling conventions change down to __csum_partial_copy_sparc_generic()"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull block fix from Jens Axboe:
"Just a single fix for a potential divide-by-zero, introduced in this
cycle"
* tag 'block-6.6-2023-10-27' of git://git.kernel.dk/linux:
blk-throttle: check for overflow in calculate_bytes_allowed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fix from Damien Le Moal:
"A single patch to fix a regression introduced by the recent
suspend/resume fixes.
The regression is that ATA disks are not stopped on system shutdown,
which is not recommended and increases the disks SMART counters for
unclean power off events.
This patch fixes this by refining the recent rework of the scsi device
manage_xxx flags"
* tag 'ata-6.6-final' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
scsi: sd: Introduce manage_shutdown device flag
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fix from Hans de Goede:
"A single patch to extend the AMD PMC driver DMI quirk list
for laptops which need special handling to avoid NVME s2idle
suspend/resume errors"
* tag 'platform-drivers-x86-v6.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: Add s2idle quirk for more Lenovo laptops
|
|
Tetsuo reported the following lockdep splat when the TSC synchronization
fails during CPU hotplug:
tsc: Marking TSC unstable due to check_tsc_sync_source failed
WARNING: inconsistent lock state
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
ffffffff8cfa1c78 (watchdog_lock){?.-.}-{2:2}, at: clocksource_watchdog+0x23/0x5a0
{IN-HARDIRQ-W} state was registered at:
_raw_spin_lock_irqsave+0x3f/0x60
clocksource_mark_unstable+0x1b/0x90
mark_tsc_unstable+0x41/0x50
check_tsc_sync_source+0x14f/0x180
sysvec_call_function_single+0x69/0x90
Possible unsafe locking scenario:
lock(watchdog_lock);
<Interrupt>
lock(watchdog_lock);
stack backtrace:
_raw_spin_lock+0x30/0x40
clocksource_watchdog+0x23/0x5a0
run_timer_softirq+0x2a/0x50
sysvec_apic_timer_interrupt+0x6e/0x90
The reason is the recent conversion of the TSC synchronization function
during CPU hotplug on the control CPU to a SMP function call. In case
that the synchronization with the upcoming CPU fails, the TSC has to be
marked unstable via clocksource_mark_unstable().
clocksource_mark_unstable() acquires 'watchdog_lock', but that lock is
taken with interrupts enabled in the watchdog timer callback to minimize
interrupt disabled time. That's obviously a possible deadlock scenario,
Before that change the synchronization function was invoked in thread
context so this could not happen.
As it is not crucical whether the unstable marking happens slightly
delayed, defer the call to a worker thread which avoids the lock context
problem.
Fixes: 9d349d47f0e3 ("x86/smpboot: Make TSC synchronization function call based")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87zg064ceg.ffs@tglx
|
|
David and a few others reported that on certain newer systems some legacy
interrupts fail to work correctly.
Debugging revealed that the BIOS of these systems leaves the legacy PIC in
uninitialized state which makes the PIC detection fail and the kernel
switches to a dummy implementation.
Unfortunately this fallback causes quite some code to fail as it depends on
checks for the number of legacy PIC interrupts or the availability of the
real PIC.
In theory there is no reason to use the PIC on any modern system when
IO/APIC is available, but the dependencies on the related checks cannot be
resolved trivially and on short notice. This needs lots of analysis and
rework.
The PIC detection has been added to avoid quirky checks and force selection
of the dummy implementation all over the place, especially in VM guest
scenarios. So it's not an option to revert the relevant commit as that
would break a lot of other scenarios.
One solution would be to try to initialize the PIC on detection fail and
retry the detection, but that puts the burden on everything which does not
have a PIC.
Fortunately the ACPI/MADT table header has a flag field, which advertises
in bit 0 that the system is PCAT compatible, which means it has a legacy
8259 PIC.
Evaluate that bit and if set avoid the detection routine and keep the real
PIC installed, which then gets initialized (for nothing) and makes the rest
of the code with all the dependencies work again.
Fixes: e179f6914152 ("x86, irq, pic: Probe for legacy PIC and set legacy_pic appropriately")
Reported-by: David Lazar <dlazar@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: David Lazar <dlazar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218003
Link: https://lore.kernel.org/r/875y2u5s8g.ffs@tglx
|
|
For "reasons" Intel has code-named this CPU with a "_H" suffix.
[ dhansen: As usual, apply this and send it upstream quickly to
make it easier for anyone who is doing work that
consumes this. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20231025202513.12358-1-tony.luck%40intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fix from Joerg Roedel:
- Fix boot regression for Sapphire Rapids with Intel VT-d driver
* tag 'iommu-fix-v6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Avoid unnecessary cache invalidations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix boot crash with FLATMEM since set_ptes() introduction
- Avoid calling arch_enter/leave_lazy_mmu() in set_ptes()
Thanks to Aneesh Kumar K.V and Erhard Furtner.
* tag 'powerpc-6.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Avoid calling arch_enter/leave_lazy_mmu() in set_ptes
powerpc/mm: Fix boot crash with FLATMEM
|
|
When suspending to idle and resuming on some Lenovo laptops using the
Mendocino APU, multiple NVME IOMMU page faults occur, showing up in
dmesg as repeated errors:
nvme 0000:01:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000b
address=0xb6674000 flags=0x0000]
The system is unstable afterwards.
Applying the s2idle quirk introduced by commit 455cd867b85b ("platform/x86:
thinkpad_acpi: Add a s2idle resume quirk for a number of laptops")
allows these systems to work with the IOMMU enabled and s2idle
resume to work.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218024
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Suggested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: David Lazar <dlazar@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/ZTlsyOaFucF2pWrL@localhost
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Fix the following kernel-doc warnings:
kernel/trace/trace_kprobe.c:1029: warning: Excess function parameter 'args' description in '__kprobe_event_gen_cmd_start'
kernel/trace/trace_kprobe.c:1097: warning: Excess function parameter 'args' description in '__kprobe_event_add_fields'
Refer to the usage of variable length arguments elsewhere in the kernel
code, "@..." is the proper way to express it in the description.
Link: https://lore.kernel.org/all/20231027041315.2613166-1-yujie.liu@intel.com/
Fixes: 2a588dd1d5d6 ("tracing: Add kprobe event command generation functions")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310190437.paI6LYJF-lkp@intel.com/
Signed-off-by: Yujie Liu <yujie.liu@intel.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
The iommu_create_device_direct_mappings() only needs to flush the caches
when the mappings are changed in the affected domain. This is not true
for non-DMA domains, or for devices attached to the domain that have no
reserved regions. To avoid unnecessary cache invalidations, add a check
before iommu_flush_iotlb_all().
Fixes: a48ce36e2786 ("iommu: Prevent RESV_DIRECT devices from blocking domains")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Henry Willard <henry.willard@oracle.com>
Link: https://lore.kernel.org/r/20231026084942.17387-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Pull drm fixes from Dave Airlie:
"This is the final set of fixes for 6.6, just misc bits mainly in
amdgpu and i915, nothing too noteworthy.
amdgpu:
- ignore duplicated BOs in CS parser
- remove redundant call to amdgpu_ctx_priority_is_valid()
- Extend VI APSM quirks to more platforms
amdkfd:
- reserve fence slot while locking BO
dp_mst:
- Fix NULL deref in get_mst_branch_device_by_guid_helper()
logicvc:
- Kconfig: Select REGMAP and REGMAP_MMIO
ivpu:
- Fix missing VPUIP interrupts
i915:
- Determine context valid in OA reports
- Hold GT forcewake during steering operations
- Check if PMU is closed before stopping event"
* tag 'drm-fixes-2023-10-27' of git://anongit.freedesktop.org/drm/drm:
accel/ivpu/37xx: Fix missing VPUIP interrupts
drm/amd: Disable ASPM for VI w/ all Intel systems
drm/i915/pmu: Check if pmu is closed before stopping event
drm/i915/mcr: Hold GT forcewake during steering operations
drm/logicvc: Kconfig: select REGMAP and REGMAP_MMIO
drm/i915/perf: Determine context valid in OA reports
drm/amdkfd: reserve a fence slot while locking the BO
drm/amdgpu: Remove redundant call to priority_is_valid()
drm/dp_mst: Fix NULL deref in get_mst_branch_device_by_guid_helper()
drm/amdgpu: ignore duplicate BOs again
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.6-2023-10-25:
amdgpu:
- Extend VI APSM quirks to more platforms
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231026035452.14921-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Determine context valid in OA reports (Umesh)
- Hold GT forcewake during steering operations (Matt Roper)
- Check if PMU is closed before stopping event (Umesh)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZTp8IQ0wxzxVjN7J@intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Short summary of fixes pull:
amdgpu:
- ignore duplicated BOs in CS parser
- remove redundant call to amdgpu_ctx_priority_is_valid()
amdkfd:
- reserve fence slot while locking BO
dp_mst:
- Fix NULL deref in get_mst_branch_device_by_guid_helper()
logicvc:
- Kconfig: Select REGMAP and REGMAP_MMIO
ivpu:
- Fix missing VPUIP interrupts
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231026110132.GA10591@linux-uq9g.fritz.box
|
|
Commit aa3998dbeb3a ("ata: libata-scsi: Disable scsi device
manage_system_start_stop") change setting the manage_system_start_stop
flag to false for libata managed disks to enable libata internal
management of disk suspend/resume. However, a side effect of this change
is that on system shutdown, disks are no longer being stopped (set to
standby mode with the heads unloaded). While this is not a critical
issue, this unclean shutdown is not recommended and shows up with
increased smart counters (e.g. the unexpected power loss counter
"Unexpect_Power_Loss_Ct").
Instead of defining a shutdown driver method for all ATA adapter
drivers (not all of them define that operation), this patch resolves
this issue by further refining the sd driver start/stop control of disks
using the new flag manage_shutdown. If this new flag is set to true by
a low level driver, the function sd_shutdown() will issue a
START STOP UNIT command with the start argument set to 0 when a disk
needs to be powered off (suspended) on system power off, that is, when
system_state is equal to SYSTEM_POWER_OFF.
Similarly to the other manage_xxx flags, the new manage_shutdown flag is
exposed through sysfs as a read-write device attribute.
To avoid any confusion between manage_shutdown and
manage_system_start_stop, the comments describing these flags in
include/scsi/scsi.h are also improved.
Fixes: aa3998dbeb3a ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218038
Link: https://lore.kernel.org/all/cd397c88-bf53-4768-9ab8-9d107df9e613@gmail.com/
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"A couple of platforms have some last-minute fixes, in particular:
- riscv gets some fixes for noncoherent DMA on the renesas and thead
platforms and dts fix for SPI on the visionfive 2 board
- Qualcomm Snapdragon gets three dts fixes to address board specific
regressions on the pmic and gpio nodes
- Rockchip platforms get multiple dts fixes to address issues on the
recent rk3399 platform as well as the older rk3128 platform that
apparently regressed a while ago.
- TI OMAP gets some trivial code and dts fixes and a regression fix
for the omap1 ams-delta modem
- NXP i.MX firmware has one fix for a use-after-free but in its error
handling"
* tag 'soc-fixes-6.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
soc: renesas: ARCH_R9A07G043 depends on !RISCV_ISA_ZICBOM
riscv: only select DMA_DIRECT_REMAP from RISCV_ISA_ZICBOM and ERRATA_THEAD_PBMT
riscv: RISCV_NONSTANDARD_CACHE_OPS shouldn't depend on RISCV_DMA_NONCOHERENT
riscv: dts: thead: set dma-noncoherent to soc bus
arm64: dts: rockchip: Fix i2s0 pin conflict on ROCK Pi 4 boards
arm64: dts: rockchip: Add i2s0-2ch-bus-bclk-off pins to RK3399
clk: ti: Fix missing omap5 mcbsp functional clock and aliases
clk: ti: Fix missing omap4 mcbsp functional clock and aliases
ARM: OMAP1: ams-delta: Fix MODEM initialization failure
soc: renesas: Make ARCH_R9A07G043 depend on required options
riscv: dts: starfive: visionfive 2: correct spi's ss pin
firmware/imx-dsp: Fix use_after_free in imx_dsp_setup_channels()
ARM: OMAP: timer32K: fix all kernel-doc warnings
ARM: omap2: fix a debug printk
ARM: dts: rockchip: Fix timer clocks for RK3128
ARM: dts: rockchip: Add missing quirk for RK3128's dma engine
ARM: dts: rockchip: Add missing arm timer interrupt for RK3128
ARM: dts: rockchip: Fix i2c0 register address for RK3128
arm64: dts: rockchip: set codec system-clock-fixed on px30-ringneck-haikou
arm64: dts: rockchip: use codec as clock master on px30-ringneck-haikou
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from WiFi and netfilter.
Most regressions addressed here come from quite old versions, with the
exceptions of the iavf one and the WiFi fixes. No known outstanding
reports or investigation.
Fixes to fixes:
- eth: iavf: in iavf_down, disable queues when removing the driver
Previous releases - regressions:
- sched: act_ct: additional checks for outdated flows
- tcp: do not leave an empty skb in write queue
- tcp: fix wrong RTO timeout when received SACK reneging
- wifi: cfg80211: pass correct pointer to rdev_inform_bss()
- eth: i40e: sync next_to_clean and next_to_process for programming
status desc
- eth: iavf: initialize waitqueues before starting watchdog_task
Previous releases - always broken:
- eth: r8169: fix data-races
- eth: igb: fix potential memory leak in igb_add_ethtool_nfc_entry
- eth: r8152: avoid writing garbage to the adapter's registers
- eth: gtp: fix fragmentation needed check with gso"
* tag 'net-6.6-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (43 commits)
iavf: in iavf_down, disable queues when removing the driver
vsock/virtio: initialize the_virtio_vsock before using VQs
net: ipv6: fix typo in comments
net: ipv4: fix typo in comments
net/sched: act_ct: additional checks for outdated flows
netfilter: flowtable: GC pushes back packets to classic path
i40e: Fix wrong check for I40E_TXR_FLAGS_WB_ON_ITR
gtp: fix fragmentation needed check with gso
gtp: uapi: fix GTPA_MAX
Fix NULL pointer dereference in cn_filter()
sfc: cleanup and reduce netlink error messages
net/handshake: fix file ref count in handshake_nl_accept_doit()
wifi: mac80211: don't drop all unprotected public action frames
wifi: cfg80211: fix assoc response warning on failed links
wifi: cfg80211: pass correct pointer to rdev_inform_bss()
isdn: mISDN: hfcsusb: Spelling fix in comment
tcp: fix wrong RTO timeout when received SACK reneging
r8152: Block future register access if register access fails
r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE
r8152: Check for unplug in r8153b_ups_en() / r8153c_ups_en()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v6.6 (take three)
- Sort out a few Kconfig dependency issues for the rich set of RISC-V
non-coherent DMA support.
* tag 'renesas-fixes-for-v6.6-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: ARCH_R9A07G043 depends on !RISCV_ISA_ZICBOM
riscv: only select DMA_DIRECT_REMAP from RISCV_ISA_ZICBOM and ERRATA_THEAD_PBMT
riscv: RISCV_NONSTANDARD_CACHE_OPS shouldn't depend on RISCV_DMA_NONCOHERENT
Link: https://lore.kernel.org/r/cover.1698312384.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ARCH_R9A07G043 has its own non-standard global pool based DMA coherent
allocator, which conflicts with the remap based RISCV_ISA_ZICBOM version.
Add a proper dependency.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231018052654.50074-4-hch@lst.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
RISCV_DMA_NONCOHERENT is also used for whacky non-standard
non-coherent ops that use different hooks in dma-direct.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20231018052654.50074-3-hch@lst.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
RISCV_NONSTANDARD_CACHE_OPS is also used for the pmem cache maintenance
helpers, which are built into the kernel unconditionally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231018052654.50074-2-hch@lst.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
