| Age | Commit message (Collapse) | Author |
|---|
|
XDP programs can shrink packets by calling the bpf_xdp_adjust_tail()
helper function. For multi-buffer packets this may lead to reduction of
frag count stored in skb_shared_info area of the xdp_buff struct. This
results in issues with the current handling of XDP_PASS and XDP_DROP
cases.
For XDP_PASS, currently skb is being built using frag count of
xdp_buffer before it was processed by XDP prog and thus will result in
an inconsistent skb when frag count gets reduced by XDP prog. To fix
this, get correct frag count while building the skb instead of using
pre-obtained frag count.
For XDP_DROP, current page recycling logic will not reuse the page but
instead will adjust the pagecnt_bias so that the page can be freed. This
again results in inconsistent behavior as the page refcnt has already
been changed by the helper while freeing the frag(s) as part of
shrinking the packet. To fix this, only adjust pagecnt_bias for buffers
that are stillpart of the packet post-xdp prog run.
Fixes: e213ced19bef ("i40e: add support for XDP multi-buffer Rx")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-6-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Fix an OOM panic in XDP_DRV mode when a XDP program shrinks a
multi-buffer packet by 4k bytes and then redirects it to an AF_XDP
socket.
Since support for handling multi-buffer frames was added to XDP, usage
of bpf_xdp_adjust_tail() helper within XDP program can free the page
that given fragment occupies and in turn decrease the fragment count
within skb_shared_info that is embedded in xdp_buff struct. In current
ice driver codebase, it can become problematic when page recycling logic
decides not to reuse the page. In such case, __page_frag_cache_drain()
is used with ice_rx_buf::pagecnt_bias that was not adjusted after
refcount of page was changed by XDP prog which in turn does not drain
the refcount to 0 and page is never freed.
To address this, let us store the count of frags before the XDP program
was executed on Rx ring struct. This will be used to compare with
current frag count from skb_shared_info embedded in xdp_buff. A smaller
value in the latter indicates that XDP prog freed frag(s). Then, for
given delta decrement pagecnt_bias for XDP_DROP verdict.
While at it, let us also handle the EOP frag within
ice_set_rx_bufs_act() to make our life easier, so all of the adjustments
needed to be applied against freed frags are performed in the single
place.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-5-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Currently when packet is shrunk via bpf_xdp_adjust_tail() and memory
type is set to MEM_TYPE_XSK_BUFF_POOL, null ptr dereference happens:
[1136314.192256] BUG: kernel NULL pointer dereference, address:
0000000000000034
[1136314.203943] #PF: supervisor read access in kernel mode
[1136314.213768] #PF: error_code(0x0000) - not-present page
[1136314.223550] PGD 0 P4D 0
[1136314.230684] Oops: 0000 [#1] PREEMPT SMP NOPTI
[1136314.239621] CPU: 8 PID: 54203 Comm: xdpsock Not tainted 6.6.0+ #257
[1136314.250469] Hardware name: Intel Corporation S2600WFT/S2600WFT,
BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[1136314.265615] RIP: 0010:__xdp_return+0x6c/0x210
[1136314.274653] Code: ad 00 48 8b 47 08 49 89 f8 a8 01 0f 85 9b 01 00 00 0f 1f 44 00 00 f0 41 ff 48 34 75 32 4c 89 c7 e9 79 cd 80 ff 83 fe 03 75 17 <f6> 41 34 01 0f 85 02 01 00 00 48 89 cf e9 22 cc 1e 00 e9 3d d2 86
[1136314.302907] RSP: 0018:ffffc900089f8db0 EFLAGS: 00010246
[1136314.312967] RAX: ffffc9003168aed0 RBX: ffff8881c3300000 RCX:
0000000000000000
[1136314.324953] RDX: 0000000000000000 RSI: 0000000000000003 RDI:
ffffc9003168c000
[1136314.336929] RBP: 0000000000000ae0 R08: 0000000000000002 R09:
0000000000010000
[1136314.348844] R10: ffffc9000e495000 R11: 0000000000000040 R12:
0000000000000001
[1136314.360706] R13: 0000000000000524 R14: ffffc9003168aec0 R15:
0000000000000001
[1136314.373298] FS: 00007f8df8bbcb80(0000) GS:ffff8897e0e00000(0000)
knlGS:0000000000000000
[1136314.386105] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1136314.396532] CR2: 0000000000000034 CR3: 00000001aa912002 CR4:
00000000007706f0
[1136314.408377] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[1136314.420173] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[1136314.431890] PKRU: 55555554
[1136314.439143] Call Trace:
[1136314.446058] <IRQ>
[1136314.452465] ? __die+0x20/0x70
[1136314.459881] ? page_fault_oops+0x15b/0x440
[1136314.468305] ? exc_page_fault+0x6a/0x150
[1136314.476491] ? asm_exc_page_fault+0x22/0x30
[1136314.484927] ? __xdp_return+0x6c/0x210
[1136314.492863] bpf_xdp_adjust_tail+0x155/0x1d0
[1136314.501269] bpf_prog_ccc47ae29d3b6570_xdp_sock_prog+0x15/0x60
[1136314.511263] ice_clean_rx_irq_zc+0x206/0xc60 [ice]
[1136314.520222] ? ice_xmit_zc+0x6e/0x150 [ice]
[1136314.528506] ice_napi_poll+0x467/0x670 [ice]
[1136314.536858] ? ttwu_do_activate.constprop.0+0x8f/0x1a0
[1136314.546010] __napi_poll+0x29/0x1b0
[1136314.553462] net_rx_action+0x133/0x270
[1136314.561619] __do_softirq+0xbe/0x28e
[1136314.569303] do_softirq+0x3f/0x60
This comes from __xdp_return() call with xdp_buff argument passed as
NULL which is supposed to be consumed by xsk_buff_free() call.
To address this properly, in ZC case, a node that represents the frag
being removed has to be pulled out of xskb_list. Introduce
appropriate xsk helpers to do such node operation and use them
accordingly within bpf_xdp_adjust_tail().
Fixes: 24ea50127ecf ("xsk: support mbuf on ZC RX")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> # For the xsk header part
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-4-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
XDP multi-buffer support introduced XDP_FLAGS_HAS_FRAGS flag that is
used by drivers to notify data path whether xdp_buff contains fragments
or not. Data path looks up mentioned flag on first buffer that occupies
the linear part of xdp_buff, so drivers only modify it there. This is
sufficient for SKB and XDP_DRV modes as usually xdp_buff is allocated on
stack or it resides within struct representing driver's queue and
fragments are carried via skb_frag_t structs. IOW, we are dealing with
only one xdp_buff.
ZC mode though relies on list of xdp_buff structs that is carried via
xsk_buff_pool::xskb_list, so ZC data path has to make sure that
fragments do *not* have XDP_FLAGS_HAS_FRAGS set. Otherwise,
xsk_buff_free() could misbehave if it would be executed against xdp_buff
that carries a frag with XDP_FLAGS_HAS_FRAGS flag set. Such scenario can
take place when within supplied XDP program bpf_xdp_adjust_tail() is
used with negative offset that would in turn release the tail fragment
from multi-buffer frame.
Calling xsk_buff_free() on tail fragment with XDP_FLAGS_HAS_FRAGS would
result in releasing all the nodes from xskb_list that were produced by
driver before XDP program execution, which is not what is intended -
only tail fragment should be deleted from xskb_list and then it should
be put onto xsk_buff_pool::free_list. Such multi-buffer frame will never
make it up to user space, so from AF_XDP application POV there would be
no traffic running, however due to free_list getting constantly new
nodes, driver will be able to feed HW Rx queue with recycled buffers.
Bottom line is that instead of traffic being redirected to user space,
it would be continuously dropped.
To fix this, let us clear the mentioned flag on xsk_buff_pool side
during xdp_buff initialization, which is what should have been done
right from the start of XSK multi-buffer support.
Fixes: 1bbc04de607b ("ice: xsk: add RX multi-buffer support")
Fixes: 1c9ba9c14658 ("i40e: xsk: add RX multi-buffer support")
Fixes: 24ea50127ecf ("xsk: support mbuf on ZC RX")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-3-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add missing xsk_buff_free() call when __xsk_rcv_zc() failed to produce
descriptor to XSK Rx queue.
Fixes: 24ea50127ecf ("xsk: support mbuf on ZC RX")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-2-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Breno Leitao says:
====================
Fix MODULE_DESCRIPTION() for net (p2)
There are hundreds of network modules that misses MODULE_DESCRIPTION(),
causing a warnning when compiling with W=1. Example:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/net/arcnet/com90io.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/net/arcnet/arc-rimi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/net/arcnet/com20020.o
This part2 of the patchset focus on the drivers/net/ethernet drivers.
There are still some missing warnings in drivers/net/ethernet that will
be fixed in an upcoming patchset.
v1: https://lore.kernel.org/all/20240122184543.2501493-2-leitao@debian.org/
====================
Link: https://lore.kernel.org/r/20240123190332.677489-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Marvel RVU mbox driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-11-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the LiteX Liteeth Ethernet device.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20240123190332.677489-10-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Freescale PQ MDIO driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-9-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the FEC (MPC8xx) Ethernet controller.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240123190332.677489-8-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the NXP ENETC Ethernet driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-7-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the EZchip NPS ethernet driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-6-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Cirrus EP93xx ethernet driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-5-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Cavium Liquidio.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-4-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Broadcom iProc GBit driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240123190332.677489-3-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to all the good old 8390 modules and drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
CC: geert@linux-m68k.org
Link: https://lore.kernel.org/r/20240123190332.677489-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This test is missing a whole bunch of checks for interface
renaming and one ifup. Presumably it was only used on a system
with renaming disabled and NetworkManager running.
Fixes: 91f430b2c49d ("selftests: net: add a test for UDP tunnel info infra")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240123060529.1033912-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If there is more than 32 cpus the bitmask will start to contain
commas, leading to:
./rps_default_mask.sh: line 36: [: 00000000,00000000: integer expression expected
Remove the commas, bash doesn't interpret leading zeroes as oct
so that should be good enough. Switch to bash, Simon reports that
not all shells support this type of substitution.
Fixes: c12e0d5f267d ("self-tests: introduce self-tests for RPS default mask")
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240122195815.638997-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull execve fixes from Kees Cook:
- Fix error handling in begin_new_exec() (Bernd Edlinger)
- MAINTAINERS: specifically mention ELF (Alexey Dobriyan)
- Various cleanups related to earlier open() (Askar Safin, Kees Cook)
* tag 'execve-v6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
exec: Distinguish in_execve from in_exec
exec: Fix error handling in begin_new_exec()
exec: Add do_close_execat() helper
exec: remove useless comment
ELF, MAINTAINERS: specifically mention ELF
|
|
Jann Horn points out that uselib() really shouldn't trigger the new
FMODE_EXEC logic introduced by commit 4759ff71f23e ("exec: __FMODE_EXEC
instead of in_execve for LSMs").
In fact, it shouldn't even have ever triggered the old pre-existing
logic for __FMODE_EXEC (like the NFS code that makes executables not
need read permissions). Unlike a real execve(), that can work even with
files that are purely executable by the user (not readable), uselib()
has that MAY_READ requirement becasue it's really just a convenience
wrapper around mmap() for legacy shared libraries.
The whole FMODE_EXEC bit was originally introduced by commit
b500531e6f5f ("[PATCH] Introduce FMODE_EXEC file flag"), primarily to
give ETXTBUSY error returns for distributed filesystems.
It has since grown a few other warts (like that NFS thing), but there
really isn't any reason to use it for uselib(), and now that we are
trying to use it to replace the horrid 'tsk->in_execve' flag, it's
actively wrong.
Of course, as Jann Horn also points out, nobody should be enabling
CONFIG_USELIB in the first place in this day and age, but that's a
different discussion entirely.
Reported-by: Jann Horn <jannh@google.com>
Fixes: 4759ff71f23e ("exec: __FMODE_EXEC instead of in_execve for LSMs")
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit b4af096b5df5dd131ab796c79cedc7069d8f4882.
New encrypted keys are created either from kernel-generated random
numbers or user-provided decrypted data. Revert the change requiring
user-provided decrypted data.
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
|
|
Register value persist after booting the kernel using
kexec which results in kernel panic. Thus clear the
BM pool registers before initialisation to fix the issue.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Jenishkumar Maheshbhai Patel <jpatel2@marvell.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://lore.kernel.org/r/20240119035914.2595665-1-jpatel2@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
otherwise the synopsys_id value may be read out wrong,
because the GMAC_VERSION register might still be in reset
state, for at least 1 us after the reset is de-asserted.
Add a wait for 10 us before continuing to be on the safe side.
> From what have you got that delay value?
Just try and error, with very old linux versions and old gcc versions
the synopsys_id was read out correctly most of the time (but not always),
with recent linux versions and recnet gcc versions it was read out
wrongly most of the time, but again not always.
I don't have access to the VHDL code in question, so I cannot
tell why it takes so long to get the correct values, I also do not
have more than a few hardware samples, so I cannot tell how long
this timeout must be in worst case.
Experimentally I can tell that the register is read several times
as zero immediately after the reset is de-asserted, also adding several
no-ops is not enough, adding a printk is enough, also udelay(1) seems to
be enough but I tried that not very often, and I have not access to many
hardware samples to be 100% sure about the necessary delay.
And since the udelay here is only executed once per device instance,
it seems acceptable to delay the boot for 10 us.
BTW: my hardware's synopsys id is 0x37.
Fixes: c5e4ddbdfa11 ("net: stmmac: Add support for optional reset control")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/AS8P193MB1285A810BD78C111E7F6AA34E4752@AS8P193MB1285.EURP193.PROD.OUTLOOK.COM
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make 'git status' quietly happy again after a full allmodconfig build.
Fixes: 60433a9d038d ("samples: introduce new samples subdir for cgroup")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Just to help distinguish the fs->in_exec flag from the current->in_execve
flag, add comments in check_unsafe_exec() and copy_fs() for more
context. Also note that in_execve is only used by TOMOYO now.
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-mm@kvack.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
After commit 978ffcbf00d8 ("execve: open the executable file before
doing anything else"), current->in_execve was no longer in sync with the
open(). This broke AppArmor and TOMOYO which depend on this flag to
distinguish "open" operations from being "exec" operations.
Instead of moving around in_execve, switch to using __FMODE_EXEC, which
is where the "is this an exec?" intent is stored. Note that TOMOYO still
uses in_execve around cred handling.
Reported-by: Kevin Locke <kevin@kevinlocke.name>
Closes: https://lore.kernel.org/all/ZbE4qn9_h14OqADK@kevinlocke.name
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: 978ffcbf00d8 ("execve: open the executable file before doing anything else")
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: James Morris <jmorris@namei.org>
Cc: Serge E. Hallyn <serge@hallyn.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: <linux-mm@kvack.org>
Cc: <apparmor@lists.ubuntu.com>
Cc: <linux-security-module@vger.kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Several expressions explicitly refer to NF_INET_* hook definitions
from expr->ops->validate, however, family is not validated.
Bail out with EOPNOTSUPP in case they are used from unsupported
families.
Fixes: 0ca743a55991 ("netfilter: nf_tables: add compatibility layer for x_tables")
Fixes: a3c90f7a2323 ("netfilter: nf_tables: flow offload expression")
Fixes: 2fa841938c64 ("netfilter: nf_tables: introduce routing expression")
Fixes: 554ced0a6e29 ("netfilter: nf_tables: add support for native socket matching")
Fixes: ad49d86e07a4 ("netfilter: nf_tables: Add synproxy support")
Fixes: 4ed8eb6570a4 ("netfilter: nf_tables: Add native tproxy support")
Fixes: 6c47260250fc ("netfilter: nf_tables: add xfrm expression")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This reverts commit e0abdadcc6e1.
core.c:nf_hook_slow assumes that the upper 16 bits of NF_DROP
verdicts contain a valid errno, i.e. -EPERM, -EHOSTUNREACH or similar,
or 0.
Due to the reverted commit, its possible to provide a positive
value, e.g. NF_ACCEPT (1), which results in use-after-free.
Its not clear to me why this commit was made.
NF_QUEUE is not used by nftables; "queue" rules in nftables
will result in use of "nft_queue" expression.
If we later need to allow specifiying errno values from userspace
(do not know why), this has to call NF_DROP_GETERR and check that
"err <= 0" holds true.
Fixes: e0abdadcc6e1 ("netfilter: nf_tables: accept QUEUE/DROP verdict parameters")
Cc: stable@vger.kernel.org
Reported-by: Notselwyn <notselwyn@pwning.tech>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
nftables has two types of sets/maps, one where userspace defines the
name, and anonymous sets/maps, where userspace defines a template name.
For the latter, kernel requires presence of exactly one "%d".
nftables uses "__set%d" and "__map%d" for this. The kernel will
expand the format specifier and replaces it with the smallest unused
number.
As-is, userspace could define a template name that allows to move
the set name past the 256 bytes upperlimit (post-expansion).
I don't see how this could be a problem, but I would prefer if userspace
cannot do this, so add a limit of 16 bytes for the '%d' template name.
16 bytes is the old total upper limit for set names that existed when
nf_tables was merged initially.
Fixes: 387454901bd6 ("netfilter: nf_tables: Allow set names of up to 255 chars")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Reject bogus configs where internal token counter wraps around.
This only occurs with very very large requests, such as 17gbyte/s.
Its better to reject this rather than having incorrect ratelimit.
Fixes: d2168e849ebf ("netfilter: nft_limit: add per-byte limiting")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Remove netdevice from inet/ingress basechain in case NETDEV_UNREGISTER
event is reported, otherwise a stale reference to netdevice remains in
the hook list.
Fixes: 60a3815da702 ("netfilter: add inet ingress support")
Cc: stable@vger.kernel.org
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
- Correct comments for nlpid, family, udlen and udata in struct nft_table,
and afinfo is no longer a member of enum nft_set_class.
- Add comment for data in struct nft_set_elem.
- Add comment for flags in struct nft_ctx.
- Add comments for timeout in struct nft_set_iter, and flags is not a
member of struct nft_set_iter, remove the comment for it.
- Add comments for commit, abort, estimate and gc_init in struct
nft_set_ops.
- Add comments for pending_update, num_exprs, exprs and catchall_list
in struct nft_set.
- Add comment for ext_len in struct nft_set_ext_tmpl.
- Add comment for inner_ops in struct nft_expr_type.
- Add comments for clone, destroy_clone, reduce, gc, offload,
offload_action, offload_stats in struct nft_expr_ops.
- Add comments for blob_gen_0, blob_gen_1, bound, genmask, udlen, udata,
blob_next in struct nft_chain.
- Add comment for flags in struct nft_base_chain.
- Add comments for udlen, udata in struct nft_object.
- Add comment for type in struct nft_object_ops.
- Add comment for hook_list in struct nft_flowtable, and remove comments
for dev_name and ops which are not members of struct nft_flowtable.
Signed-off-by: George Guo <guodongtai@kylinos.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When the CPU goes idle for the last time during the CPU down hotplug
process, RCU reports a final quiescent state for the current CPU. If
this quiescent state propagates up to the top, some tasks may then be
woken up to complete the grace period: the main grace period kthread
and/or the expedited main workqueue (or kworker).
If those kthreads have a SCHED_FIFO policy, the wake up can indirectly
arm the RT bandwith timer to the local offline CPU. Since this happens
after hrtimers have been migrated at CPUHP_AP_HRTIMERS_DYING stage, the
timer gets ignored. Therefore if the RCU kthreads are waiting for RT
bandwidth to be available, they may never be actually scheduled.
This triggers TREE03 rcutorture hangs:
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 4-...!: (1 GPs behind) idle=9874/1/0x4000000000000000 softirq=0/0 fqs=20 rcuc=21071 jiffies(starved)
rcu: (t=21035 jiffies g=938281 q=40787 ncpus=6)
rcu: rcu_preempt kthread starved for 20964 jiffies! g938281 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x0 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:R running task stack:14896 pid:14 tgid:14 ppid:2 flags:0x00004000
Call Trace:
<TASK>
__schedule+0x2eb/0xa80
schedule+0x1f/0x90
schedule_timeout+0x163/0x270
? __pfx_process_timeout+0x10/0x10
rcu_gp_fqs_loop+0x37c/0x5b0
? __pfx_rcu_gp_kthread+0x10/0x10
rcu_gp_kthread+0x17c/0x200
kthread+0xde/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2b/0x40
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The situation can't be solved with just unpinning the timer. The hrtimer
infrastructure and the nohz heuristics involved in finding the best
remote target for an unpinned timer would then also need to handle
enqueues from an offline CPU in the most horrendous way.
So fix this on the RCU side instead and defer the wake up to an online
CPU if it's too late for the local one.
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Neeraj Upadhyay (AMD) <neeraj.iitr10@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes and cleanups from Helge Deller:
"A crash fix in stifb which was missed to be included in the drm-misc
tree, two checks to prevent wrong userspace input in sisfb and
savagefb and two trivial printk cleanups:
- stifb: Fix crash in stifb_blank()
- savage/sis: Error out if pixclock equals zero
- minor trivial cleanups"
* tag 'fbdev-for-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: stifb: Fix crash in stifb_blank()
fbcon: Fix incorrect printed function name in fbcon_prepare_logo()
fbdev: sis: Error out if pixclock equals zero
fbdev: savage: Error out if pixclock equals zero
fbdev: vt8500lcdfb: Remove unnecessary print function dev_err()
|
|
The test on so_count in nfsd4_release_lockowner() is nonsense and
harmful. Revert to using check_for_locks(), changing that to not sleep.
First: harmful.
As is documented in the kdoc comment for nfsd4_release_lockowner(), the
test on so_count can transiently return a false positive resulting in a
return of NFS4ERR_LOCKS_HELD when in fact no locks are held. This is
clearly a protocol violation and with the Linux NFS client it can cause
incorrect behaviour.
If RELEASE_LOCKOWNER is sent while some other thread is still
processing a LOCK request which failed because, at the time that request
was received, the given owner held a conflicting lock, then the nfsd
thread processing that LOCK request can hold a reference (conflock) to
the lock owner that causes nfsd4_release_lockowner() to return an
incorrect error.
The Linux NFS client ignores that NFS4ERR_LOCKS_HELD error because it
never sends NFS4_RELEASE_LOCKOWNER without first releasing any locks, so
it knows that the error is impossible. It assumes the lock owner was in
fact released so it feels free to use the same lock owner identifier in
some later locking request.
When it does reuse a lock owner identifier for which a previous RELEASE
failed, it will naturally use a lock_seqid of zero. However the server,
which didn't release the lock owner, will expect a larger lock_seqid and
so will respond with NFS4ERR_BAD_SEQID.
So clearly it is harmful to allow a false positive, which testing
so_count allows.
The test is nonsense because ... well... it doesn't mean anything.
so_count is the sum of three different counts.
1/ the set of states listed on so_stateids
2/ the set of active vfs locks owned by any of those states
3/ various transient counts such as for conflicting locks.
When it is tested against '2' it is clear that one of these is the
transient reference obtained by find_lockowner_str_locked(). It is not
clear what the other one is expected to be.
In practice, the count is often 2 because there is precisely one state
on so_stateids. If there were more, this would fail.
In my testing I see two circumstances when RELEASE_LOCKOWNER is called.
In one case, CLOSE is called before RELEASE_LOCKOWNER. That results in
all the lock states being removed, and so the lockowner being discarded
(it is removed when there are no more references which usually happens
when the lock state is discarded). When nfsd4_release_lockowner() finds
that the lock owner doesn't exist, it returns success.
The other case shows an so_count of '2' and precisely one state listed
in so_stateid. It appears that the Linux client uses a separate lock
owner for each file resulting in one lock state per lock owner, so this
test on '2' is safe. For another client it might not be safe.
So this patch changes check_for_locks() to use the (newish)
find_any_file_locked() so that it doesn't take a reference on the
nfs4_file and so never calls nfsd_file_put(), and so never sleeps. With
this check is it safe to restore the use of check_for_locks() rather
than testing so_count against the mysterious '2'.
Fixes: ce3c4ad7f4ce ("NFSD: Fix possible sleep during nfsd4_release_lockowner()")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
When kcalloc() for ft->g succeeds but kvzalloc() for in fails,
fs_any_create_groups() will free ft->g. However, its caller
fs_any_create_table() will free ft->g again through calling
mlx5e_destroy_flow_table(), which will lead to a double-free.
Fix this by setting ft->g to NULL in fs_any_create_groups().
Fixes: 0f575c20bf06 ("net/mlx5e: Introduce Flow Steering ANY API")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When `in` allocated by kvzalloc fails, arfs_create_groups will free
ft->g and return an error. However, arfs_create_table, the only caller of
arfs_create_groups, will hold this error and call to
mlx5e_destroy_flow_table, in which the ft->g will be freed again.
Fixes: 1cabe6b0965e ("net/mlx5e: Create aRFS flow tables")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
XFRM stack doesn't prevent from users to configure replay window
in TX side and strongswan sets replay_window to be 1. It causes
to failures in validation logic when trying to offload the SA.
Replay window is not relevant in TX side and should be ignored.
Fixes: cded6d80129b ("net/mlx5e: Store replay window in XFRM attributes")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
All ConnectX devices have software parsing capability enabled, but it is
more correct to set allow_swp only if capability exists, which for IPsec
means that crypto offload is supported.
Fixes: 2451da081a34 ("net/mlx5: Unify device IPsec capabilities check")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5 devices have specific constants for choosing the CQ period mode. These
constants do not have to match the constants used by the kernel software
API for DIM period mode selection.
Fixes: cdd04f4d4d71 ("net/mlx5: Add support to create SQ and CQ for ASO")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Go-To-Vport action on RX is not allowed when the vport is uplink.
In such case, the packet should be dropped.
Fixes: 9db810ed2d37 ("net/mlx5: DR, Expose steering action functionality")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When FW provides ICM addresses for drop RX/TX, the provided capability
is 64 bits that contain its GVMI as well as the ICM address itself.
In case of TX DROP this GVMI is different from the GVMI that the
domain is operating on.
This patch fixes the action to use these GVMI IDs, as provided by FW.
Fixes: 9db810ed2d37 ("net/mlx5: DR, Expose steering action functionality")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
To enable multicast packets which are offloaded in bridge multicast
offload mode to be sent also to uplink, FTE bit uplink_hairpin_en should
be set. Add this bit to FTE for the bridge multicast offload rules.
Fixes: 18c2916cee12 ("net/mlx5: Bridge, snoop igmp/mld packets")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The below WARN [1] is reported once a callback command failed.
As a callback runs under an interrupt context, needs to use the IRQ
save/restore variant.
[1]
DEBUG_LOCKS_WARN_ON(lockdep_hardirq_context())
WARNING: CPU: 15 PID: 0 at kernel/locking/lockdep.c:4353
lockdep_hardirqs_on_prepare+0x11b/0x180
Modules linked in: vhost_net vhost tap mlx5_vfio_pci
vfio_pci vfio_pci_core vfio_iommu_type1 vfio mlx5_vdpa vringh
vhost_iotlb vdpa nfnetlink_cttimeout openvswitch nsh ip6table_mangle
ip6table_nat ip6table_filter ip6_tables iptable_mangle
xt_conntrackxt_MASQUERADE nf_conntrack_netlink nfnetlink
xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5
auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi
scsi_transport_iscsi rdma_cm iw_cm ib_umad ib_ipoib ib_cm
mlx5_ib ib_uverbs ib_core fuse mlx5_core
CPU: 15 PID: 0 Comm: swapper/15 Tainted: G W 6.7.0-rc4+ #1587
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:lockdep_hardirqs_on_prepare+0x11b/0x180
Code: 00 5b c3 c3 e8 e6 0d 58 00 85 c0 74 d6 8b 15 f0 c3
76 01 85 d2 75 cc 48 c7 c6 04 a5 3b 82 48 c7 c7 f1
e9 39 82 e8 95 12 f9 ff <0f> 0b 5b c3 e8 bc 0d 58 00
85 c0 74 ac 8b 3d c6 c3 76 01 85 ff 75
RSP: 0018:ffffc900003ecd18 EFLAGS: 00010086
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000027
RDX: 0000000000000000 RSI: ffff88885fbdb880 RDI: ffff88885fbdb888
RBP: 00000000ffffff87 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 284e4f5f4e524157 R12: 00000000002c9aa1
R13: ffff88810aace980 R14: ffff88810aace9b8 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff88885fbc0000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f731436f4c8 CR3: 000000010aae6001 CR4: 0000000000372eb0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
? __warn+0x81/0x170
? lockdep_hardirqs_on_prepare+0x11b/0x180
? report_bug+0xf8/0x1c0
? handle_bug+0x3f/0x70
? exc_invalid_op+0x13/0x60
? asm_exc_invalid_op+0x16/0x20
? lockdep_hardirqs_on_prepare+0x11b/0x180
? lockdep_hardirqs_on_prepare+0x11b/0x180
trace_hardirqs_on+0x4a/0xa0
raw_spin_unlock_irq+0x24/0x30
cmd_status_err+0xc0/0x1a0 [mlx5_core]
cmd_status_err+0x1a0/0x1a0 [mlx5_core]
mlx5_cmd_exec_cb_handler+0x24/0x40 [mlx5_core]
mlx5_cmd_comp_handler+0x129/0x4b0 [mlx5_core]
cmd_comp_notifier+0x1a/0x20 [mlx5_core]
notifier_call_chain+0x3e/0xe0
atomic_notifier_call_chain+0x5f/0x130
mlx5_eq_async_int+0xe7/0x200 [mlx5_core]
notifier_call_chain+0x3e/0xe0
atomic_notifier_call_chain+0x5f/0x130
irq_int_handler+0x11/0x20 [mlx5_core]
__handle_irq_event_percpu+0x99/0x220
? tick_irq_enter+0x5d/0x80
handle_irq_event_percpu+0xf/0x40
handle_irq_event+0x3a/0x60
handle_edge_irq+0xa2/0x1c0
__common_interrupt+0x55/0x140
common_interrupt+0x7d/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0x13/0x20
Code: c0 08 00 00 00 4d 29 c8 4c 01 c7 4c 29 c2 e9 72 ff
ff ff cc cc cc cc 8b 05 ea 08 25 01 85 c0 7e 07 0f 00 2d 7f b0 26 00 fb
f4 <fa> c3 90 66 2e 0f 1f 84 00 00 00 00 00 65 48 8b 04 25 80 d0 02 00
RSP: 0018:ffffc9000010fec8 EFLAGS: 00000242
RAX: 0000000000000001 RBX: 000000000000000f RCX: 4000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff811c410c
RBP: ffffffff829478c0 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
? do_idle+0x1ec/0x210
default_idle_call+0x6c/0x90
do_idle+0x1ec/0x210
cpu_startup_entry+0x26/0x30
start_secondary+0x11b/0x150
secondary_startup_64_no_verify+0x165/0x16b
</TASK>
irq event stamp: 833284
hardirqs last enabled at (833283): [<ffffffff811c410c>]
do_idle+0x1ec/0x210
hardirqs last disabled at (833284): [<ffffffff81daf9ef>]
common_interrupt+0xf/0xa0
softirqs last enabled at (833224): [<ffffffff81dc199f>]
__do_softirq+0x2bf/0x40e
softirqs last disabled at (833177): [<ffffffff81178ddf>]
irq_exit_rcu+0x7f/0xa0
Fixes: 34f46ae0d4b3 ("net/mlx5: Add command failures data to debugfs")
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited change refactored mlx5e_tc_del_fdb_peer_flow() to only clear DUP
flag when list of peer flows has become empty. However, if any concurrent
user holds a reference to a peer flow (for example, the neighbor update
workqueue task is updating peer flow's parent encap entry concurrently),
then the flow will not be removed from the peer list and, consecutively,
DUP flag will remain set. Since mlx5e_tc_del_fdb_peers_flow() calls
mlx5e_tc_del_fdb_peer_flow() for every possible peer index the algorithm
will try to remove the flow from eswitch instances that it has never peered
with causing either NULL pointer dereference when trying to remove the flow
peer list head of peer_index that was never initialized or a warning if the
list debug config is enabled[0].
Fix the issue by always removing the peer flow from the list even when not
releasing the last reference to it.
[0]:
[ 3102.985806] ------------[ cut here ]------------
[ 3102.986223] list_del corruption, ffff888139110698->next is NULL
[ 3102.986757] WARNING: CPU: 2 PID: 22109 at lib/list_debug.c:53 __list_del_entry_valid_or_report+0x4f/0xc0
[ 3102.987561] Modules linked in: act_ct nf_flow_table bonding act_tunnel_key act_mirred act_skbedit vxlan cls_matchall nfnetlink_cttimeout act_gact cls_flower sch_ingress mlx5_vdpa vringh vhost_iotlb vdpa openvswitch nsh xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat xt_addrtype xt_conntrack nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcg
ss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5_core [last unloaded: bonding]
[ 3102.991113] CPU: 2 PID: 22109 Comm: revalidator28 Not tainted 6.6.0-rc6+ #3
[ 3102.991695] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 3102.992605] RIP: 0010:__list_del_entry_valid_or_report+0x4f/0xc0
[ 3102.993122] Code: 39 c2 74 56 48 8b 32 48 39 fe 75 62 48 8b 51 08 48 39 f2 75 73 b8 01 00 00 00 c3 48 89 fe 48 c7 c7 48 fd 0a 82 e8 41 0b ad ff <0f> 0b 31 c0 c3 48 89 fe 48 c7 c7 70 fd 0a 82 e8 2d 0b ad ff 0f 0b
[ 3102.994615] RSP: 0018:ffff8881383e7710 EFLAGS: 00010286
[ 3102.995078] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
[ 3102.995670] RDX: 0000000000000001 RSI: ffff88885f89b640 RDI: ffff88885f89b640
[ 3102.997188] DEL flow 00000000be367878 on port 0
[ 3102.998594] RBP: dead000000000122 R08: 0000000000000000 R09: c0000000ffffdfff
[ 3102.999604] R10: 0000000000000008 R11: ffff8881383e7598 R12: dead000000000100
[ 3103.000198] R13: 0000000000000002 R14: ffff888139110000 R15: ffff888101901240
[ 3103.000790] FS: 00007f424cde4700(0000) GS:ffff88885f880000(0000) knlGS:0000000000000000
[ 3103.001486] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3103.001986] CR2: 00007fd42e8dcb70 CR3: 000000011e68a003 CR4: 0000000000370ea0
[ 3103.002596] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 3103.003190] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 3103.003787] Call Trace:
[ 3103.004055] <TASK>
[ 3103.004297] ? __warn+0x7d/0x130
[ 3103.004623] ? __list_del_entry_valid_or_report+0x4f/0xc0
[ 3103.005094] ? report_bug+0xf1/0x1c0
[ 3103.005439] ? console_unlock+0x4a/0xd0
[ 3103.005806] ? handle_bug+0x3f/0x70
[ 3103.006149] ? exc_invalid_op+0x13/0x60
[ 3103.006531] ? asm_exc_invalid_op+0x16/0x20
[ 3103.007430] ? __list_del_entry_valid_or_report+0x4f/0xc0
[ 3103.007910] mlx5e_tc_del_fdb_peers_flow+0xcf/0x240 [mlx5_core]
[ 3103.008463] mlx5e_tc_del_flow+0x46/0x270 [mlx5_core]
[ 3103.008944] mlx5e_flow_put+0x26/0x50 [mlx5_core]
[ 3103.009401] mlx5e_delete_flower+0x25f/0x380 [mlx5_core]
[ 3103.009901] tc_setup_cb_destroy+0xab/0x180
[ 3103.010292] fl_hw_destroy_filter+0x99/0xc0 [cls_flower]
[ 3103.010779] __fl_delete+0x2d4/0x2f0 [cls_flower]
[ 3103.011207] fl_delete+0x36/0x80 [cls_flower]
[ 3103.011614] tc_del_tfilter+0x56f/0x750
[ 3103.011982] rtnetlink_rcv_msg+0xff/0x3a0
[ 3103.012362] ? netlink_ack+0x1c7/0x4e0
[ 3103.012719] ? rtnl_calcit.isra.44+0x130/0x130
[ 3103.013134] netlink_rcv_skb+0x54/0x100
[ 3103.013533] netlink_unicast+0x1ca/0x2b0
[ 3103.013902] netlink_sendmsg+0x361/0x4d0
[ 3103.014269] __sock_sendmsg+0x38/0x60
[ 3103.014643] ____sys_sendmsg+0x1f2/0x200
[ 3103.015018] ? copy_msghdr_from_user+0x72/0xa0
[ 3103.015265] ___sys_sendmsg+0x87/0xd0
[ 3103.016608] ? copy_msghdr_from_user+0x72/0xa0
[ 3103.017014] ? ___sys_recvmsg+0x9b/0xd0
[ 3103.017381] ? ttwu_do_activate.isra.137+0x58/0x180
[ 3103.017821] ? wake_up_q+0x49/0x90
[ 3103.018157] ? futex_wake+0x137/0x160
[ 3103.018521] ? __sys_sendmsg+0x51/0x90
[ 3103.018882] __sys_sendmsg+0x51/0x90
[ 3103.019230] ? exit_to_user_mode_prepare+0x56/0x130
[ 3103.019670] do_syscall_64+0x3c/0x80
[ 3103.020017] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 3103.020469] RIP: 0033:0x7f4254811ef4
[ 3103.020816] Code: 89 f3 48 83 ec 10 48 89 7c 24 08 48 89 14 24 e8 42 eb ff ff 48 8b 14 24 41 89 c0 48 89 de 48 8b 7c 24 08 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 30 44 89 c7 48 89 04 24 e8 78 eb ff ff 48 8b
[ 3103.022290] RSP: 002b:00007f424cdd9480 EFLAGS: 00000293 ORIG_RAX: 000000000000002e
[ 3103.022970] RAX: ffffffffffffffda RBX: 00007f424cdd9510 RCX: 00007f4254811ef4
[ 3103.023564] RDX: 0000000000000000 RSI: 00007f424cdd9510 RDI: 0000000000000012
[ 3103.024158] RBP: 00007f424cdda238 R08: 0000000000000000 R09: 00007f41d801a4b0
[ 3103.024748] R10: 0000000000000000 R11: 0000000000000293 R12: 0000000000000001
[ 3103.025341] R13: 00007f424cdd9510 R14: 00007f424cdda240 R15: 00007f424cdd99a0
[ 3103.025931] </TASK>
[ 3103.026182] ---[ end trace 0000000000000000 ]---
[ 3103.027033] ------------[ cut here ]------------
Fixes: 9be6c21fdcf8 ("net/mlx5e: Handle offloads flows per peer")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The processing of traffic in hairpin queues occurs in HW/FW and does not
involve the cpus, hence the upper bound on max num channels does not
apply to them. Using this bound for the hairpin RQT max_table_size is
wrong. It could be too small, and cause the error below [1]. As the
RQT size provided on init does not get modified later, use the same
value for both actual and max table sizes.
[1]
mlx5_core 0000:08:00.1: mlx5_cmd_out_err:805:(pid 1200): CREATE_RQT(0x916) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x538faf), err(-22)
Fixes: 74a8dadac17e ("net/mlx5e: Preparations for supporting larger number of channels")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Indirection (*) is of lower precedence than postfix increment (++). Logic
in napi_poll context would cause an out-of-bound read by first increment
the pointer address by byte address space and then dereference the value.
Rather, the intended logic was to dereference first and then increment the
underlying value.
Fixes: 92214be5979c ("net/mlx5e: Update doorbell for port timestamping CQ before the software counter")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The sd_group field moved in the HW spec from the MPIR register
to the vport context.
Align the query accordingly.
Fixes: f5e956329960 ("net/mlx5: Expose Management PCIe Index Register (MPIR)")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit moved the code of mlx5e_create_tises() and changed the
loop to create TISes over MLX5_MAX_PORTS constant value, instead of
getting the correct lag ports supported by the device, which can cause
FW errors on devices with less than MLX5_MAX_PORTS ports.
Change that back to mlx5e_get_num_lag_ports(mdev).
Also IPoIB interfaces create there own TISes, they don't use the eth
TISes, pass a flag to indicate that.
This fixes the following errors that might appear in kernel log:
mlx5_cmd_out_err:808:(pid 650): CREATE_TIS(0x912) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x595b5d), err(-22)
mlx5e_create_mdev_resources:174:(pid 650): alloc tises failed, -22
Fixes: b25bd37c859f ("net/mlx5: Move TISes from priv to mdev HW resources")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When a qdisc is deleted from a net device the stack instructs the
underlying driver to remove its flow offload callback from the
associated filter block using the 'FLOW_BLOCK_UNBIND' command. The stack
then continues to replay the removal of the filters in the block for
this driver by iterating over the chains in the block and invoking the
'reoffload' operation of the classifier being used. In turn, the
classifier in its 'reoffload' operation prepares and emits a
'FLOW_CLS_DESTROY' command for each filter.
However, the stack does not do the same for chain templates and the
underlying driver never receives a 'FLOW_CLS_TMPLT_DESTROY' command when
a qdisc is deleted. This results in a memory leak [1] which can be
reproduced using [2].
Fix by introducing a 'tmplt_reoffload' operation and have the stack
invoke it with the appropriate arguments as part of the replay.
Implement the operation in the sole classifier that supports chain
templates (flower) by emitting the 'FLOW_CLS_TMPLT_{CREATE,DESTROY}'
command based on whether a flow offload callback is being bound to a
filter block or being unbound from one.
As far as I can tell, the issue happens since cited commit which
reordered tcf_block_offload_unbind() before tcf_block_flush_all_chains()
in __tcf_block_put(). The order cannot be reversed as the filter block
is expected to be freed after flushing all the chains.
[1]
unreferenced object 0xffff888107e28800 (size 2048):
comm "tc", pid 1079, jiffies 4294958525 (age 3074.287s)
hex dump (first 32 bytes):
b1 a6 7c 11 81 88 ff ff e0 5b b3 10 81 88 ff ff ..|......[......
01 00 00 00 00 00 00 00 e0 aa b0 84 ff ff ff ff ................
backtrace:
[<ffffffff81c06a68>] __kmem_cache_alloc_node+0x1e8/0x320
[<ffffffff81ab374e>] __kmalloc+0x4e/0x90
[<ffffffff832aec6d>] mlxsw_sp_acl_ruleset_get+0x34d/0x7a0
[<ffffffff832bc195>] mlxsw_sp_flower_tmplt_create+0x145/0x180
[<ffffffff832b2e1a>] mlxsw_sp_flow_block_cb+0x1ea/0x280
[<ffffffff83a10613>] tc_setup_cb_call+0x183/0x340
[<ffffffff83a9f85a>] fl_tmplt_create+0x3da/0x4c0
[<ffffffff83a22435>] tc_ctl_chain+0xa15/0x1170
[<ffffffff838a863c>] rtnetlink_rcv_msg+0x3cc/0xed0
[<ffffffff83ac87f0>] netlink_rcv_skb+0x170/0x440
[<ffffffff83ac6270>] netlink_unicast+0x540/0x820
[<ffffffff83ac6e28>] netlink_sendmsg+0x8d8/0xda0
[<ffffffff83793def>] ____sys_sendmsg+0x30f/0xa80
[<ffffffff8379d29a>] ___sys_sendmsg+0x13a/0x1e0
[<ffffffff8379d50c>] __sys_sendmsg+0x11c/0x1f0
[<ffffffff843b9ce0>] do_syscall_64+0x40/0xe0
unreferenced object 0xffff88816d2c0400 (size 1024):
comm "tc", pid 1079, jiffies 4294958525 (age 3074.287s)
hex dump (first 32 bytes):
40 00 00 00 00 00 00 00 57 f6 38 be 00 00 00 00 @.......W.8.....
10 04 2c 6d 81 88 ff ff 10 04 2c 6d 81 88 ff ff ..,m......,m....
backtrace:
[<ffffffff81c06a68>] __kmem_cache_alloc_node+0x1e8/0x320
[<ffffffff81ab36c1>] __kmalloc_node+0x51/0x90
[<ffffffff81a8ed96>] kvmalloc_node+0xa6/0x1f0
[<ffffffff82827d03>] bucket_table_alloc.isra.0+0x83/0x460
[<ffffffff82828d2b>] rhashtable_init+0x43b/0x7c0
[<ffffffff832aed48>] mlxsw_sp_acl_ruleset_get+0x428/0x7a0
[<ffffffff832bc195>] mlxsw_sp_flower_tmplt_create+0x145/0x180
[<ffffffff832b2e1a>] mlxsw_sp_flow_block_cb+0x1ea/0x280
[<ffffffff83a10613>] tc_setup_cb_call+0x183/0x340
[<ffffffff83a9f85a>] fl_tmplt_create+0x3da/0x4c0
[<ffffffff83a22435>] tc_ctl_chain+0xa15/0x1170
[<ffffffff838a863c>] rtnetlink_rcv_msg+0x3cc/0xed0
[<ffffffff83ac87f0>] netlink_rcv_skb+0x170/0x440
[<ffffffff83ac6270>] netlink_unicast+0x540/0x820
[<ffffffff83ac6e28>] netlink_sendmsg+0x8d8/0xda0
[<ffffffff83793def>] ____sys_sendmsg+0x30f/0xa80
[2]
# tc qdisc add dev swp1 clsact
# tc chain add dev swp1 ingress proto ip chain 1 flower dst_ip 0.0.0.0/32
# tc qdisc del dev swp1 clsact
# devlink dev reload pci/0000:06:00.0
Fixes: bbf73830cd48 ("net: sched: traverse chains in block with tcf_get_next_chain()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
