| Age | Commit message (Collapse) | Author |
|---|
|
Commit 6654111c893f ("MIPS: vmlinux.lds.S: align raw appended dtb to 8
bytes") changed the alignment from STRUCT_ALIGNMENT bytes to 8 bytes.
The commit's message makes it sound like it was actually done on
purpose, but this is not the case. The commit was written when raw
appended dtb were not aligned at all. The STRUCT_ALIGN() was added a few
days before, in commit 7a05293af39f ("MIPS: boot/compressed: Copy DTB to
aligned address"). The true purpose of the commit was not to align
specifically to 8 bytes, but to make sure that the generated vmlinux'
size was properly padded to the alignment required for DTBs.
While the switch to 8-byte alignment worked for vmlinux-appended dtb
blobs, it broke vmlinuz-appended dtb blobs, as the decompress routine
moves the blob to a STRUCT_ALIGNMENT aligned address.
Fix this by changing the raw appended dtb blob alignment from 8 bytes
back to STRUCT_ALIGNMENT bytes in vmlinux.lds.S.
Fixes: 6654111c893f ("MIPS: vmlinux.lds.S: align raw appended dtb to 8 bytes")
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Save the current_thread_info()->status of X86 in the new
restart_block->arch_data field so TS_COMPAT_RESTART can be removed again.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210201174716.GA17898@redhat.com
|
|
The comment in get_nr_restart_syscall() says:
* The problem is that we can get here when ptrace pokes
* syscall-like values into regs even if we're not in a syscall
* at all.
Yes, but if not in a syscall then the
status & (TS_COMPAT|TS_I386_REGS_POKED)
check below can't really help:
- TS_COMPAT can't be set
- TS_I386_REGS_POKED is only set if regs->orig_ax was changed by
32bit debugger; and even in this case get_nr_restart_syscall()
is only correct if the tracee is 32bit too.
Suppose that a 64bit debugger plays with a 32bit tracee and
* Tracee calls sleep(2) // TS_COMPAT is set
* User interrupts the tracee by CTRL-C after 1 sec and does
"(gdb) call func()"
* gdb saves the regs by PTRACE_GETREGS
* does PTRACE_SETREGS to set %rip='func' and %orig_rax=-1
* PTRACE_CONT // TS_COMPAT is cleared
* func() hits int3.
* Debugger catches SIGTRAP.
* Restore original regs by PTRACE_SETREGS.
* PTRACE_CONT
get_nr_restart_syscall() wrongly returns __NR_restart_syscall==219, the
tracee calls ia32_sys_call_table[219] == sys_madvise.
Add the sticky TS_COMPAT_RESTART flag which survives after return to user
mode. It's going to be removed in the next step again by storing the
information in the restart block. As a further cleanup it might be possible
to remove also TS_I386_REGS_POKED with that.
Test-case:
$ cvs -d :pserver:anoncvs:anoncvs@sourceware.org:/cvs/systemtap co ptrace-tests
$ gcc -o erestartsys-trap-debuggee ptrace-tests/tests/erestartsys-trap-debuggee.c --m32
$ gcc -o erestartsys-trap-debugger ptrace-tests/tests/erestartsys-trap-debugger.c -lutil
$ ./erestartsys-trap-debugger
Unexpected: retval 1, errno 22
erestartsys-trap-debugger: ptrace-tests/tests/erestartsys-trap-debugger.c:421
Fixes: 609c19a385c8 ("x86/ptrace: Stop setting TS_COMPAT in ptrace code")
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210201174709.GA17895@redhat.com
|
|
Move TS_COMPAT back to asm/thread_info.h, close to TS_I386_REGS_POKED.
It was moved to asm/processor.h by b9d989c7218a ("x86/asm: Move the
thread_info::status field to thread_struct"), then later 37a8f7c38339
("x86/asm: Move 'status' from thread_struct to thread_info") moved the
'status' field back but TS_COMPAT was forgotten.
Preparatory patch to fix the COMPAT case for get_nr_restart_syscall()
Fixes: 609c19a385c8 ("x86/ptrace: Stop setting TS_COMPAT in ptrace code")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210201174649.GA17880@redhat.com
|
|
Preparation for fixing get_nr_restart_syscall() on X86 for COMPAT.
Add a new helper which sets restart_block->fn and calls a dummy
arch_set_restart_data() helper.
Fixes: 609c19a385c8 ("x86/ptrace: Stop setting TS_COMPAT in ptrace code")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210201174641.GA17871@redhat.com
|
|
On a Haswell machine, the perf_fuzzer managed to trigger this message:
[117248.075892] unchecked MSR access error: WRMSR to 0x3f1 (tried to
write 0x0400000000000000) at rIP: 0xffffffff8106e4f4
(native_write_msr+0x4/0x20)
[117248.089957] Call Trace:
[117248.092685] intel_pmu_pebs_enable_all+0x31/0x40
[117248.097737] intel_pmu_enable_all+0xa/0x10
[117248.102210] __perf_event_task_sched_in+0x2df/0x2f0
[117248.107511] finish_task_switch.isra.0+0x15f/0x280
[117248.112765] schedule_tail+0xc/0x40
[117248.116562] ret_from_fork+0x8/0x30
A fake event called VLBR_EVENT may use the bit 58 of the PEBS_ENABLE, if
the precise_ip is set. The bit 58 is reserved by the HW. Accessing the
bit causes the unchecked MSR access error.
The fake event doesn't support PEBS. The case should be rejected.
Fixes: 097e4311cda9 ("perf/x86: Add constraint to create guest LBR event without hw counter")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1615555298-140216-2-git-send-email-kan.liang@linux.intel.com
|
|
A repeatable crash can be triggered by the perf_fuzzer on some Haswell
system.
https://lore.kernel.org/lkml/7170d3b-c17f-1ded-52aa-cc6d9ae999f4@maine.edu/
For some old CPUs (HSW and earlier), the PEBS status in a PEBS record
may be mistakenly set to 0. To minimize the impact of the defect, the
commit was introduced to try to avoid dropping the PEBS record for some
cases. It adds a check in the intel_pmu_drain_pebs_nhm(), and updates
the local pebs_status accordingly. However, it doesn't correct the PEBS
status in the PEBS record, which may trigger the crash, especially for
the large PEBS.
It's possible that all the PEBS records in a large PEBS have the PEBS
status 0. If so, the first get_next_pebs_record_by_bit() in the
__intel_pmu_pebs_event() returns NULL. The at = NULL. Since it's a large
PEBS, the 'count' parameter must > 1. The second
get_next_pebs_record_by_bit() will crash.
Besides the local pebs_status, correct the PEBS status in the PEBS
record as well.
Fixes: 01330d7288e0 ("perf/x86: Allow zero PEBS status with only single active event")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1615555298-140216-1-git-send-email-kan.liang@linux.intel.com
|
|
When freeing a tree block we may end up adding its extent back to the
free space cache/tree, as long as there are no more references for it,
it was created in the current transaction and writeback for it never
happened. This is generally fine, however when we have tree mod log
operations it can result in inconsistent versions of a btree after
unwinding extent buffers with the recorded tree mod log operations.
This is because:
* We only log operations for nodes (adding and removing key/pointers),
for leaves we don't do anything;
* This means that we can log a MOD_LOG_KEY_REMOVE_WHILE_FREEING operation
for a node that points to a leaf that was deleted;
* Before we apply the logged operation to unwind a node, we can have
that leaf's extent allocated again, either as a node or as a leaf, and
possibly for another btree. This is possible if the leaf was created in
the current transaction and writeback for it never started, in which
case btrfs_free_tree_block() returns its extent back to the free space
cache/tree;
* Then, before applying the tree mod log operation, some task allocates
the metadata extent just freed before, and uses it either as a leaf or
as a node for some btree (can be the same or another one, it does not
matter);
* After applying the MOD_LOG_KEY_REMOVE_WHILE_FREEING operation we now
get the target node with an item pointing to the metadata extent that
now has content different from what it had before the leaf was deleted.
It might now belong to a different btree and be a node and not a leaf
anymore.
As a consequence, the results of searches after the unwinding can be
unpredictable and produce unexpected results.
So make sure we pin extent buffers corresponding to leaves when there
are tree mod log users.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
While resolving backreferences, as part of a logical ino ioctl call or
fiemap, we can end up hitting a BUG_ON() when replaying tree mod log
operations of a root, triggering a stack trace like the following:
------------[ cut here ]------------
kernel BUG at fs/btrfs/ctree.c:1210!
invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 1 PID: 19054 Comm: crawl_335 Tainted: G W 5.11.0-2d11c0084b02-misc-next+ #89
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
RIP: 0010:__tree_mod_log_rewind+0x3b1/0x3c0
Code: 05 48 8d 74 10 (...)
RSP: 0018:ffffc90001eb70b8 EFLAGS: 00010297
RAX: 0000000000000000 RBX: ffff88812344e400 RCX: ffffffffb28933b6
RDX: 0000000000000007 RSI: dffffc0000000000 RDI: ffff88812344e42c
RBP: ffffc90001eb7108 R08: 1ffff11020b60a20 R09: ffffed1020b60a20
R10: ffff888105b050f9 R11: ffffed1020b60a1f R12: 00000000000000ee
R13: ffff8880195520c0 R14: ffff8881bc958500 R15: ffff88812344e42c
FS: 00007fd1955e8700(0000) GS:ffff8881f5600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007efdb7928718 CR3: 000000010103a006 CR4: 0000000000170ee0
Call Trace:
btrfs_search_old_slot+0x265/0x10d0
? lock_acquired+0xbb/0x600
? btrfs_search_slot+0x1090/0x1090
? free_extent_buffer.part.61+0xd7/0x140
? free_extent_buffer+0x13/0x20
resolve_indirect_refs+0x3e9/0xfc0
? lock_downgrade+0x3d0/0x3d0
? __kasan_check_read+0x11/0x20
? add_prelim_ref.part.11+0x150/0x150
? lock_downgrade+0x3d0/0x3d0
? __kasan_check_read+0x11/0x20
? lock_acquired+0xbb/0x600
? __kasan_check_write+0x14/0x20
? do_raw_spin_unlock+0xa8/0x140
? rb_insert_color+0x30/0x360
? prelim_ref_insert+0x12d/0x430
find_parent_nodes+0x5c3/0x1830
? resolve_indirect_refs+0xfc0/0xfc0
? lock_release+0xc8/0x620
? fs_reclaim_acquire+0x67/0xf0
? lock_acquire+0xc7/0x510
? lock_downgrade+0x3d0/0x3d0
? lockdep_hardirqs_on_prepare+0x160/0x210
? lock_release+0xc8/0x620
? fs_reclaim_acquire+0x67/0xf0
? lock_acquire+0xc7/0x510
? poison_range+0x38/0x40
? unpoison_range+0x14/0x40
? trace_hardirqs_on+0x55/0x120
btrfs_find_all_roots_safe+0x142/0x1e0
? find_parent_nodes+0x1830/0x1830
? btrfs_inode_flags_to_xflags+0x50/0x50
iterate_extent_inodes+0x20e/0x580
? tree_backref_for_extent+0x230/0x230
? lock_downgrade+0x3d0/0x3d0
? read_extent_buffer+0xdd/0x110
? lock_downgrade+0x3d0/0x3d0
? __kasan_check_read+0x11/0x20
? lock_acquired+0xbb/0x600
? __kasan_check_write+0x14/0x20
? _raw_spin_unlock+0x22/0x30
? __kasan_check_write+0x14/0x20
iterate_inodes_from_logical+0x129/0x170
? iterate_inodes_from_logical+0x129/0x170
? btrfs_inode_flags_to_xflags+0x50/0x50
? iterate_extent_inodes+0x580/0x580
? __vmalloc_node+0x92/0xb0
? init_data_container+0x34/0xb0
? init_data_container+0x34/0xb0
? kvmalloc_node+0x60/0x80
btrfs_ioctl_logical_to_ino+0x158/0x230
btrfs_ioctl+0x205e/0x4040
? __might_sleep+0x71/0xe0
? btrfs_ioctl_get_supported_features+0x30/0x30
? getrusage+0x4b6/0x9c0
? __kasan_check_read+0x11/0x20
? lock_release+0xc8/0x620
? __might_fault+0x64/0xd0
? lock_acquire+0xc7/0x510
? lock_downgrade+0x3d0/0x3d0
? lockdep_hardirqs_on_prepare+0x210/0x210
? lockdep_hardirqs_on_prepare+0x210/0x210
? __kasan_check_read+0x11/0x20
? do_vfs_ioctl+0xfc/0x9d0
? ioctl_file_clone+0xe0/0xe0
? lock_downgrade+0x3d0/0x3d0
? lockdep_hardirqs_on_prepare+0x210/0x210
? __kasan_check_read+0x11/0x20
? lock_release+0xc8/0x620
? __task_pid_nr_ns+0xd3/0x250
? lock_acquire+0xc7/0x510
? __fget_files+0x160/0x230
? __fget_light+0xf2/0x110
__x64_sys_ioctl+0xc3/0x100
do_syscall_64+0x37/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fd1976e2427
Code: 00 00 90 48 8b 05 (...)
RSP: 002b:00007fd1955e5cf8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fd1955e5f40 RCX: 00007fd1976e2427
RDX: 00007fd1955e5f48 RSI: 00000000c038943b RDI: 0000000000000004
RBP: 0000000001000000 R08: 0000000000000000 R09: 00007fd1955e6120
R10: 0000557835366b00 R11: 0000000000000246 R12: 0000000000000004
R13: 00007fd1955e5f48 R14: 00007fd1955e5f40 R15: 00007fd1955e5ef8
Modules linked in:
---[ end trace ec8931a1c36e57be ]---
(gdb) l *(__tree_mod_log_rewind+0x3b1)
0xffffffff81893521 is in __tree_mod_log_rewind (fs/btrfs/ctree.c:1210).
1205 * the modification. as we're going backwards, we do the
1206 * opposite of each operation here.
1207 */
1208 switch (tm->op) {
1209 case MOD_LOG_KEY_REMOVE_WHILE_FREEING:
1210 BUG_ON(tm->slot < n);
1211 fallthrough;
1212 case MOD_LOG_KEY_REMOVE_WHILE_MOVING:
1213 case MOD_LOG_KEY_REMOVE:
1214 btrfs_set_node_key(eb, &tm->key, tm->slot);
Here's what happens to hit that BUG_ON():
1) We have one tree mod log user (through fiemap or the logical ino ioctl),
with a sequence number of 1, so we have fs_info->tree_mod_seq == 1;
2) Another task is at ctree.c:balance_level() and we have eb X currently as
the root of the tree, and we promote its single child, eb Y, as the new
root.
Then, at ctree.c:balance_level(), we call:
tree_mod_log_insert_root(eb X, eb Y, 1);
3) At tree_mod_log_insert_root() we create tree mod log elements for each
slot of eb X, of operation type MOD_LOG_KEY_REMOVE_WHILE_FREEING each
with a ->logical pointing to ebX->start. These are placed in an array
named tm_list.
Lets assume there are N elements (N pointers in eb X);
4) Then, still at tree_mod_log_insert_root(), we create a tree mod log
element of operation type MOD_LOG_ROOT_REPLACE, ->logical set to
ebY->start, ->old_root.logical set to ebX->start, ->old_root.level set
to the level of eb X and ->generation set to the generation of eb X;
5) Then tree_mod_log_insert_root() calls tree_mod_log_free_eb() with
tm_list as argument. After that, tree_mod_log_free_eb() calls
__tree_mod_log_insert() for each member of tm_list in reverse order,
from highest slot in eb X, slot N - 1, to slot 0 of eb X;
6) __tree_mod_log_insert() sets the sequence number of each given tree mod
log operation - it increments fs_info->tree_mod_seq and sets
fs_info->tree_mod_seq as the sequence number of the given tree mod log
operation.
This means that for the tm_list created at tree_mod_log_insert_root(),
the element corresponding to slot 0 of eb X has the highest sequence
number (1 + N), and the element corresponding to the last slot has the
lowest sequence number (2);
7) Then, after inserting tm_list's elements into the tree mod log rbtree,
the MOD_LOG_ROOT_REPLACE element is inserted, which gets the highest
sequence number, which is N + 2;
8) Back to ctree.c:balance_level(), we free eb X by calling
btrfs_free_tree_block() on it. Because eb X was created in the current
transaction, has no other references and writeback did not happen for
it, we add it back to the free space cache/tree;
9) Later some other task T allocates the metadata extent from eb X, since
it is marked as free space in the space cache/tree, and uses it as a
node for some other btree;
10) The tree mod log user task calls btrfs_search_old_slot(), which calls
get_old_root(), and finally that calls __tree_mod_log_oldest_root()
with time_seq == 1 and eb_root == eb Y;
11) First iteration of the while loop finds the tree mod log element with
sequence number N + 2, for the logical address of eb Y and of type
MOD_LOG_ROOT_REPLACE;
12) Because the operation type is MOD_LOG_ROOT_REPLACE, we don't break out
of the loop, and set root_logical to point to tm->old_root.logical
which corresponds to the logical address of eb X;
13) On the next iteration of the while loop, the call to
tree_mod_log_search_oldest() returns the smallest tree mod log element
for the logical address of eb X, which has a sequence number of 2, an
operation type of MOD_LOG_KEY_REMOVE_WHILE_FREEING and corresponds to
the old slot N - 1 of eb X (eb X had N items in it before being freed);
14) We then break out of the while loop and return the tree mod log operation
of type MOD_LOG_ROOT_REPLACE (eb Y), and not the one for slot N - 1 of
eb X, to get_old_root();
15) At get_old_root(), we process the MOD_LOG_ROOT_REPLACE operation
and set "logical" to the logical address of eb X, which was the old
root. We then call tree_mod_log_search() passing it the logical
address of eb X and time_seq == 1;
16) Then before calling tree_mod_log_search(), task T adds a key to eb X,
which results in adding a tree mod log operation of type
MOD_LOG_KEY_ADD to the tree mod log - this is done at
ctree.c:insert_ptr() - but after adding the tree mod log operation
and before updating the number of items in eb X from 0 to 1...
17) The task at get_old_root() calls tree_mod_log_search() and gets the
tree mod log operation of type MOD_LOG_KEY_ADD just added by task T.
Then it enters the following if branch:
if (old_root && tm && tm->op != MOD_LOG_KEY_REMOVE_WHILE_FREEING) {
(...)
} (...)
Calls read_tree_block() for eb X, which gets a reference on eb X but
does not lock it - task T has it locked.
Then it clones eb X while it has nritems set to 0 in its header, before
task T sets nritems to 1 in eb X's header. From hereupon we use the
clone of eb X which no other task has access to;
18) Then we call __tree_mod_log_rewind(), passing it the MOD_LOG_KEY_ADD
mod log operation we just got from tree_mod_log_search() in the
previous step and the cloned version of eb X;
19) At __tree_mod_log_rewind(), we set the local variable "n" to the number
of items set in eb X's clone, which is 0. Then we enter the while loop,
and in its first iteration we process the MOD_LOG_KEY_ADD operation,
which just decrements "n" from 0 to (u32)-1, since "n" is declared with
a type of u32. At the end of this iteration we call rb_next() to find the
next tree mod log operation for eb X, that gives us the mod log operation
of type MOD_LOG_KEY_REMOVE_WHILE_FREEING, for slot 0, with a sequence
number of N + 1 (steps 3 to 6);
20) Then we go back to the top of the while loop and trigger the following
BUG_ON():
(...)
switch (tm->op) {
case MOD_LOG_KEY_REMOVE_WHILE_FREEING:
BUG_ON(tm->slot < n);
fallthrough;
(...)
Because "n" has a value of (u32)-1 (4294967295) and tm->slot is 0.
Fix this by taking a read lock on the extent buffer before cloning it at
ctree.c:get_old_root(). This should be done regardless of the extent
buffer having been freed and reused, as a concurrent task might be
modifying it (while holding a write lock on it).
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org>
Link: https://lore.kernel.org/linux-btrfs/20210227155037.GN28049@hungrycats.org/
Fixes: 834328a8493079 ("Btrfs: tree mod log's old roots could still be part of the tree")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The free space tree bitmap slab cache is created with SLAB_RED_ZONE but
that's a debugging flag and not always enabled. Also the other slabs are
created with at least SLAB_MEM_SPREAD that we want as well to average
the memory placement cost.
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Fixes: 3acd48507dc4 ("btrfs: fix allocation of free space cache v1 bitmap pages")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Store the address space ID in the TDP iterator so that it can be
retrieved without having to bounce through the root shadow page. This
streamlines the code and fixes a Sparse warning about not properly using
rcu_dereference() when grabbing the ID from the root on the fly.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210315233803.2706477-5-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In tdp_mmu_iter_cond_resched there is a call to tdp_iter_start which
causes the iterator to continue its walk over the paging structure from
the root. This is needed after a yield as paging structure could have
been freed in the interim.
The tdp_iter_start call is not very clear and something of a hack. It
requires exposing tdp_iter fields not used elsewhere in tdp_mmu.c and
the effect is not obvious from the function name. Factor a more aptly
named function out of tdp_iter_start and call it from
tdp_mmu_iter_cond_resched and tdp_iter_start.
No functional change intended.
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210315233803.2706477-4-bgardon@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Fix a missing rcu_dereference in tdp_mmu_zap_spte_atomic.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210315233803.2706477-3-bgardon@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The pt passed into handle_removed_tdp_mmu_page does not need RCU
protection, as it is not at any risk of being freed by another thread at
that point. However, the implicit cast from tdp_sptep_t to u64 * dropped
the __rcu annotation without a proper rcu_derefrence. Fix this by
passing the pt as a tdp_ptep_t and then rcu_dereferencing it in
the function.
Suggested-by: Sean Christopherson <seanjc@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210315233803.2706477-2-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Sameer Pujar <spujar@nvidia.com>:
With commit 1e30f642cf29 ("ASoC: simple-card-utils: Fix device module clock")
simple-card-utils can control MCLK clock for rate updates or enable/disable.
But this is breaking some platforms where it is expected that codec drivers
would actually handle the MCLK clock. One such example is following platform.
- "arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts"
In above case codec, wm8904, is using internal PLL and configures sysclk
based on fixed MCLK input. In such cases it is expected that, required PLL
output or sysclk, is just passed via set_sysclk() callback and card driver
need not actually update MCLK rate. Instead, codec can take ownership of
this clock and do the necessary configuration.
So the original commit is reverted and codec driver for rt5659 is updated
to fix my board which has this codec.
Sameer Pujar (2):
ASoC: simple-card-utils: Do not handle device clock
ASoC: rt5659: Update MCLK rate in set_sysclk()
sound/soc/codecs/rt5659.c | 5 +++++
sound/soc/generic/simple-card-utils.c | 13 +++++++------
2 files changed, 12 insertions(+), 6 deletions(-)
--
2.7.4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"Fix a deadlock and a couple of other bugs"
* tag 'fuse-fixes-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: 32-bit user space ioctl compat for fuse device
virtiofs: Fail dax mount if device does not support it
fuse: fix live lock in fuse_iget()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Miscellaneous NFSD fixes for v5.12-rc"
* tag 'nfsd-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
svcrdma: Revert "svcrdma: Reduce Receive doorbell rate"
NFSD: fix error handling in NFSv4.0 callbacks
NFSD: fix dest to src mount in inter-server COPY
Revert "nfsd4: a client's own opens needn't prevent delegations"
Revert "nfsd4: remove check_conflicting_opens warning"
rpc: fix NULL dereference on kmalloc failure
sunrpc: fix refcount leak for rpc auth modules
NFSD: Repair misuse of sv_lock in 5.10.16-rt30.
nfsd: don't abort copies early
fs: nfsd: fix kconfig dependency warning for NFSD_V4
svcrdma: disable timeouts on rdma backchannel
nfsd: Don't keep looking up unhashed files in the nfsd file cache
|
|
vaddr_get_pfns() now returns the positive number of pfns successfully
gotten instead of zero. vfio_pin_page_external() might return 1 to
vfio_iommu_type1_pin_pages(), which will treat it as an error, if
vaddr_get_pfns() is successful but vfio_pin_page_external() doesn't
reach vfio_lock_acct().
Fix it up in vfio_pin_page_external(). Found by inspection.
Fixes: be16c1fd99f4 ("vfio/type1: Change success value of vaddr_get_pfn()")
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Message-Id: <20210308172452.38864-1-daniel.m.jordan@oracle.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
VFIO_IOMMU_TYPE1 does not compile with !MMU:
../drivers/vfio/vfio_iommu_type1.c: In function 'follow_fault_pfn':
../drivers/vfio/vfio_iommu_type1.c:536:22: error: implicit declaration of function 'pte_write'; did you mean 'vfs_write'? [-Werror=implicit-function-declaration]
So require it.
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <0-v1-02cb5500df6e+78-vfio_no_mmu_jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
CONFIG_VFIO_AMBA has a light use of AMBA, adding some inline fallbacks
when AMBA is disabled will allow it to be compiled under COMPILE_TEST and
make VFIO easier to maintain.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <3-v1-df057e0f92c3+91-vfio_arm_compile_test_jgg@nvidia.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
x86 can build platform bus code too, so vfio-platform and all the platform
reset implementations compile successfully on x86.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <2-v1-df057e0f92c3+91-vfio_arm_compile_test_jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
As IOMMU_API is a kconfig without a description (eg does not show in the
menu) the correct operator is select not 'depends on'. Using 'depends on'
for this kind of symbol means VFIO is not selectable unless some other
random kconfig has already enabled IOMMU_API for it.
Fixes: cba3345cc494 ("vfio: VFIO core")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <1-v1-df057e0f92c3+91-vfio_arm_compile_test_jgg@nvidia.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Some ILP32 architectures support mapping a 32-bit vaddr within a 64-bit
iova space. The unmap-all code uses 32-bit SIZE_MAX as an upper bound on
the extent of the mappings within iova space, so mappings above 4G cannot
be found and unmapped. Use U64_MAX instead, and use u64 for size variables.
This also fixes a static analysis bug found by the kernel test robot running
smatch for ILP32.
Fixes: 0f53afa12bae ("vfio/type1: unmap cleanup")
Fixes: c19650995374 ("vfio/type1: implement unmap all")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Message-Id: <1614281102-230747-1-git-send-email-steven.sistare@oracle.com>
Link: https://lore.kernel.org/linux-mm/20210222141043.GW2222@kadam
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
With a 64-bit kernel build the FUSE device cannot handle ioctl requests
coming from 32-bit user space. This is due to the ioctl command
translation that generates different command identifiers that thus cannot
be used for direct comparisons without proper manipulation.
Explicitly extract type and number from the ioctl command to enable 32-bit
user space compatibility on 64-bit kernel builds.
Signed-off-by: Alessio Balsini <balsini@android.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
The HP EliteBook 850 G8 Notebook PC is using ALC285 codec which is
using 0x04 to control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210316094236.89028-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add compatible string for new added platforms which support spdif module.
They are i.MX8QXP, i.MX8MM, i.MX8MN, i.MX8MQ.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1615884053-4264-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We do some IO operations in the snd_soc_component_set_jack callback
function and snd_soc_component_set_jack() will be called when soc
component is removed. However, we should not access SoundWire registers
when the bus is suspended.
So set regcache_cache_only(regmap, true) to avoid accessing in the
soc component removal process.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210316005254.29699-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Simple-card/audio-graph-card drivers do not handle MCLK clock when it
is specified in the codec device node. The expectation here is that,
the codec should actually own up the MCLK clock and do necessary setup
in the driver.
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1615829492-8972-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This reverts commit 1e30f642cf29 ("ASoC: simple-card-utils: Fix device
module clock"). The original patch ended up breaking following platform,
which depends on set_sysclk() to configure internal PLL on wm8904 codec
and expects simple-card-utils to not update the MCLK rate.
- "arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts"
It would be best if codec takes care of setting MCLK clock via DAI
set_sysclk() callback.
Reported-by: Michael Walle <michael@walle.cc>
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Fixes: 1e30f642cf29 ("ASoC: simple-card-utils: Fix device module clock")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/1615829492-8972-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In readahead infrastructure, we are using a lot of hard coded PAGE_SHIFT
while we're not doing anything specific to PAGE_SIZE.
One of the most affected part is the radix tree operation of
btrfs_fs_info::reada_tree.
If using PAGE_SHIFT, subpage metadata readahead is broken and does no
help reading metadata ahead.
Fix the problem by using btrfs_fs_info::sectorsize_bits so that
readahead could work for subpage.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
[BUG]
When running fstests for btrfs subpage read-write test, it has a very
high chance to crash at generic/475 with the following stack:
BTRFS warning (device dm-8): direct IO failed ino 510 rw 1,34817 sector 0xcdf0 len 94208 err no 10
Unable to handle kernel paging request at virtual address ffff80001157e7c0
CPU: 2 PID: 687125 Comm: kworker/u12:4 Tainted: G WC 5.12.0-rc2-custom+ #5
Hardware name: Khadas VIM3 (DT)
Workqueue: btrfs-endio-meta btrfs_work_helper [btrfs]
pc : queued_spin_lock_slowpath+0x1a0/0x390
lr : do_raw_spin_lock+0xc4/0x11c
Call trace:
queued_spin_lock_slowpath+0x1a0/0x390
_raw_spin_lock+0x68/0x84
btree_readahead_hook+0x38/0xc0 [btrfs]
end_bio_extent_readpage+0x504/0x5f4 [btrfs]
bio_endio+0x170/0x1a4
end_workqueue_fn+0x3c/0x60 [btrfs]
btrfs_work_helper+0x1b0/0x1b4 [btrfs]
process_one_work+0x22c/0x430
worker_thread+0x70/0x3a0
kthread+0x13c/0x140
ret_from_fork+0x10/0x30
Code: 910020e0 8b0200c2 f861d884 aa0203e1 (f8246827)
[CAUSE]
In end_bio_extent_readpage(), if we hit an error during read, we will
handle the error differently for data and metadata.
For data we queue a repair, while for metadata, we record the error and
let the caller choose what to do.
But the code is still using page->private to grab extent buffer, which
no longer points to extent buffer for subpage metadata pages.
Thus this wild pointer access leads to above crash.
[FIX]
Introduce a helper, find_extent_buffer_readpage(), to grab extent
buffer.
The difference against find_extent_buffer_nospinlock() is:
- Also handles regular sectorsize == PAGE_SIZE case
- No extent buffer refs increase/decrease
As extent buffer under IO must have non-zero refs, so this is safe
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
In case when the properties are supplied in the secondary fwnode
(for example, built-in device properties) the fwnode pointer left
unassigned. This makes unable to retrieve them.
Assign fwnode to parent's if no primary one provided.
Fixes: 7cba1a4d5e16 ("gpiolib: generalize devprop_gpiochip_set_names() for device properties")
Fixes: 2afa97e9868f ("gpiolib: Read "gpio-line-names" from a firmware node")
Reported-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
zonefs updates the size of a sequential zone file inode only on
completion of direct writes. When executing asynchronous append writes
(with a file open with O_APPEND or using RWF_APPEND), the use of the
current inode size in generic_write_checks() to set an iocb offset thus
leads to unaligned write if an application issues an append write
operation with another write already being executed.
Fix this problem by introducing zonefs_write_checks() as a modified
version of generic_write_checks() using the file inode wp_offset for an
append write iocb offset. Also introduce zonefs_write_check_limits() to
replace generic_write_check_limits() call. This zonefs special helper
makes sure that the maximum file limit used is the maximum size of the
file being accessed.
Since zonefs_write_checks() already truncates the iov_iter, the calls
to iov_iter_truncate() in zonefs_file_dio_write() and
zonefs_file_buffered_write() are removed.
Fixes: 8dcc1a9d90c1 ("fs: New zonefs file system")
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
|
|
The sequential write constraint of sequential zone file prevent their
use as swap files. Only allow conventional zone files to be used as swap
files.
Fixes: 8dcc1a9d90c1 ("fs: New zonefs file system")
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
|
|
The HP EliteBook 840 G8 Notebook PC is using ALC236 codec which is
using 0x02 to control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210316074626.79895-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The HP EliteBook 840 G8 Notebook PC is using ALC285 codec which is
using 0x04 to control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210316065452.75659-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If copy_from_user() or kstrtoull() fail then the correct behavior is to
return a negative error code.
Link: https://lore.kernel.org/r/YEsbU/UxYypVrC7/@mwanda
Fixes: f9bb2da11db8 ("[SCSI] lpfc 8.3.27: T10 additions for SLI4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Only half of the file is under include guard because terminating #endif
is placed too early.
Link: https://lore.kernel.org/r/YE4snvoW1SuwcXAn@localhost.localdomain
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In st_open(), if STp->in_use is true, STp will be freed by
scsi_tape_put(). However, STp is still used by DEBC_printk() after. It is
better to DEBC_printk() before scsi_tape_put().
Link: https://lore.kernel.org/r/20210311064636.10522-1-lyl2019@mail.ustc.edu.cn
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In myrs_cleanup(), cs->mmio_base will be freed twice by iounmap().
Link: https://lore.kernel.org/r/20210311063005.9963-1-lyl2019@mail.ustc.edu.cn
Fixes: 77266186397c ("scsi: myrs: Add Mylex RAID controller (SCSI interface)")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The buffer for negotiating channel setup is DMA allocated at device probe
time. However, the remove path fails to free this allocation which will
prevent the hypervisor from releasing the virtual device in the case of a
hotplug remove.
Fix this issue by freeing the buffer allocation in ibmvfc_free_mem().
Link: https://lore.kernel.org/r/20210311012212.428068-1-tyreld@linux.ibm.com
Fixes: e95eef3fc0bc ("scsi: ibmvfc: Implement channel enquiry and setup commands")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
- Fix an oops in AFS that can be triggered by accessing one of the
afs.yfs.* xattrs against an OpenAFS server - for instance by commands
like "cp -a"[1], "rsync -X" or getfattr[2]. These try and copy all of
the xattrs.
cp and rsync should pay attention to the list in /etc/xattr.conf, but
cp doesn't on Ubuntu and rsync doesn't seem to on Ubuntu or Fedora.
xattr.conf has been modified upstream[3], and a new version has just
been cut that includes it. I've logged a bug against rsync for the
problem there[4].
- Stop listing "afs.*" xattrs[5][6][7], but particularly ACL ones[8] so
that they don't confuse cp and rsync.
This removes them from the list returned by listxattr(), but they're
still available to get/set.
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003498.html [1]
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003501.html [2]
Link: https://git.savannah.nongnu.org/cgit/attr.git/commit/?id=74da517cc655a82ded715dea7245ce88ebc91b98 [3]
Link: https://github.com/WayneD/rsync/issues/163 [4]
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003516.html [5]
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003524.html [6]
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003565.html # v1
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003568.html [7]
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003570.html [8]
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003571.html # v2
* tag 'afs-fixes-20210315' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Stop listxattr() from listing "afs.*" attributes
afs: Fix accessing YFS xattrs on a non-YFS server
|
|
Built-in microphone and combojack on Xiaomi Notebook Pro (1d72:1701) needs
to be fixed, the existing quirk for Dell works well on that machine.
Signed-off-by: Xiaoliang Yu <yxl_22@outlook.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/OS0P286MB02749B9E13920E6899902CD8EE6C9@OS0P286MB0274.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In commit 05bc1be6db4b2 ("s390/pci: create zPCI bus") we removed the
pci_dev_put() call matching the earlier pci_get_slot() done as part of
__zpci_event_availability(). This was based on the wrong understanding
that the device_put() done as part of pci_destroy_device() would counter
the pci_get_slot() when it only counters the initial reference. This
same understanding and existing bad example also lead to not doing
a pci_dev_put() in zpci_remove_device().
Since releasing the PCI devices, unlike releasing the PCI slot, does not
print any debug message for testing I added one in pci_release_dev().
This revealed that we are indeed leaking the PCI device on PCI
hotunplug. Further testing also revealed another missing pci_dev_put() in
disable_slot().
Fix this by adding the missing pci_dev_put() in disable_slot() and fix
zpci_remove_device() with the correct pci_dev_put() calls. Also instead
of calling pci_get_slot() in __zpci_event_availability() to determine if
a PCI device is registered and then doing the same again in
zpci_remove_device() do this once in zpci_remove_device() which makes
sure that the pdev in __zpci_event_availability() is only used for the
result of pci_scan_single_device() which does not need a reference count
decremnt as its ownership goes to the PCI bus.
Also move the check if zdev->zbus->bus is set into zpci_remove_device()
since it may be that we're removing a device with devfn != 0 which never
had a PCI bus. So we can still set the pdev->error_state to indicate
that the device is not usable anymore, add a flag to set the error state.
Fixes: 05bc1be6db4b2 ("s390/pci: create zPCI bus")
Cc: <stable@vger.kernel.org> # 5.8+: e1bff843cde6 s390/pci: remove superfluous zdev->zbus check
Cc: <stable@vger.kernel.org> # 5.8+: ba764dd703fe s390/pci: refactor zpci_create_device()
Cc: <stable@vger.kernel.org> # 5.8+
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Commit 152e9b8676c6e ("s390/vtime: steal time exponential moving average")
inadvertently changed the input value for account_steal_time() from
"cputime_to_nsecs(steal)" to just "steal", resulting in broken increased
steal time accounting.
Fix this by changing it back to "cputime_to_nsecs(steal)".
Fixes: 152e9b8676c6e ("s390/vtime: steal time exponential moving average")
Cc: <stable@vger.kernel.org> # 5.1
Reported-by: Sabine Forkel <sabine.forkel@de.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The following BUG message was triggered repeatedly when complete counter
sets are extracted from the CPUMF:
BUG: using smp_processor_id() in preemptible [00000000]
code: psvc-readsets/7759
caller is cf_diag_needspace+0x2c/0x100
CPU: 7 PID: 7759 Comm: psvc-readsets Not tainted 5.12.0
Hardware name: IBM 3906 M03 703 (LPAR)
Call Trace:
[<00000000c7043f78>] show_stack+0x90/0xf8
[<00000000c705776a>] dump_stack+0xba/0x108
[<00000000c705d91c>] check_preemption_disabled+0xec/0xf0
[<00000000c63eb1c4>] cf_diag_needspace+0x2c/0x100
[<00000000c63ecbcc>] cf_diag_ioctl_start+0x10c/0x240
[<00000000c63ece9a>] cf_diag_ioctl+0x19a/0x238
[<00000000c675f3f4>] __s390x_sys_ioctl+0xc4/0x100
[<00000000c63ca762>] do_syscall+0x82/0xd0
[<00000000c705bdd8>] __do_syscall+0xc0/0xd8
[<00000000c706d532>] system_call+0x72/0x98
2 locks held by psvc-readsets/7759:
#0: 00000000c75a57c0 (cpu_hotplug_lock){++++}-{0:0},
at: cf_diag_ioctl+0x44/0x238
#1: 00000000c75a3078 (cf_diag_ctrset_mutex){+.+.}-{3:3},
at: cf_diag_ioctl+0x54/0x238
This issue is a missing get_cpu_ptr/put_cpu_ptr pair in function
cf_diag_needspace. Add it.
Fixes: cf6acb8bdb1d ("s390/cpumf: Add support for complete counter set extraction")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
[Why]
With certain fclock overclocks, state 1 may be chosen
as the closest clock level. This may result in this state
being empty if not populated beforehand, resulting in
black screens and screen corruption.
[How]
Copy over all soc states to clock_limits before bounding
box creation to avoid any cases with empty states.
Fixes: f2459c52c84449 ("drm/amd/display: Add Bounding Box State for Low DF PState but High Voltage State")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1514
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
afs_listxattr() lists all the available special afs xattrs (i.e. those in
the "afs.*" space), no matter what type of server we're dealing with. But
OpenAFS servers, for example, cannot deal with some of the extra-capable
attributes that AuriStor (YFS) servers provide. Unfortunately, the
presence of the afs.yfs.* attributes causes errors[1] for anything that
tries to read them if the server is of the wrong type.
Fix the problem by removing afs_listxattr() so that none of the special
xattrs are listed (AFS doesn't support xattrs). It does mean, however,
that getfattr won't list them, though they can still be accessed with
getxattr() and setxattr().
This can be tested with something like:
getfattr -d -m ".*" /afs/example.com/path/to/file
With this change, none of the afs.* attributes should be visible.
Changes:
ver #2:
- Hide all of the afs.* xattrs, not just the ACL ones.
Fixes: ae46578b963f ("afs: Get YFS ACLs and information through xattrs")
Reported-by: Gaja Sophie Peters <gaja.peters@math.uni-hamburg.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Gaja Sophie Peters <gaja.peters@math.uni-hamburg.de>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003502.html [1]
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003567.html # v1
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003573.html # v2
|
|
If someone attempts to access YFS-related xattrs (e.g. afs.yfs.acl) on a
file on a non-YFS AFS server (such as OpenAFS), then the kernel will jump
to a NULL function pointer because the afs_fetch_acl_operation descriptor
doesn't point to a function for issuing an operation on a non-YFS
server[1].
Fix this by making afs_wait_for_operation() check that the issue_afs_rpc
method is set before jumping to it and setting -ENOTSUPP if not. This fix
also covers other potential operations that also only exist on YFS servers.
afs_xattr_get/set_yfs() then need to translate -ENOTSUPP to -ENODATA as the
former error is internal to the kernel.
The bug shows up as an oops like the following:
BUG: kernel NULL pointer dereference, address: 0000000000000000
[...]
Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6.
[...]
Call Trace:
afs_wait_for_operation+0x83/0x1b0 [kafs]
afs_xattr_get_yfs+0xe6/0x270 [kafs]
__vfs_getxattr+0x59/0x80
vfs_getxattr+0x11c/0x140
getxattr+0x181/0x250
? __check_object_size+0x13f/0x150
? __fput+0x16d/0x250
__x64_sys_fgetxattr+0x64/0xb0
do_syscall_64+0x49/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fb120a9defe
This was triggered with "cp -a" which attempts to copy xattrs, including
afs ones, but is easier to reproduce with getfattr, e.g.:
getfattr -d -m ".*" /afs/openafs.org/
Fixes: e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept")
Reported-by: Gaja Sophie Peters <gaja.peters@math.uni-hamburg.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Gaja Sophie Peters <gaja.peters@math.uni-hamburg.de>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: linux-afs@lists.infradead.org
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003498.html [1]
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003566.html # v1
Link: http://lists.infradead.org/pipermail/linux-afs/2021-March/003572.html # v2
|
|
When using a zoned filesystem, while syncing the log, if we fail to
allocate the root node for the log root tree, we are not removing the
log context we allocated on stack from the list of log contexts of the
log root tree. This means after the return from btrfs_sync_log() we get
a corrupted linked list.
Fix this by allocating the node before adding our stack allocated context
to the list of log contexts of the log root tree.
Fixes: 3ddebf27fcd3a9 ("btrfs: zoned: reorder log node allocation on zoned filesystem")
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
