| Age | Commit message (Collapse) | Author |
|---|
|
The BCM2835 SPI driver currently sets the SPI_CONTROLLER_MUST_RX flag.
When performing a TX-only transfer, this flag causes the SPI core to
allocate and DMA-map a dummy buffer into which the RX FIFO contents are
copied. The dummy buffer is necessary because the chip is not capable
of disabling the receiver or automatically throwing away received data.
Not reading the RX FIFO isn't an option either since transmission is
halted once it's full.
Avoid the overhead induced by the dummy buffer by preallocating a
reusable DMA transaction which cyclically clears the RX FIFO. The
transaction requires very little CPU time to submit and generates no
interrupts while running. Specifics are provided in kerneldoc comments.
With a ks8851 Ethernet chip attached to the SPI controller, I am seeing
a 30 us reduction in ping time with this commit (1.819 ms vs. 1.849 ms,
average of 100,000 packets) as well as a 2% reduction in CPU time
(75:08 vs. 76:39 for transmission of 5 GByte over the SPI bus).
The commit uses the TX DMA interrupt to signal completion of a transfer.
This interrupt is raised once all bytes have been written to the
TX FIFO and it is then necessary to busy-wait for the TX FIFO to become
empty before the transfer can be finalized. As an alternative approach,
I have explored using the SPI controller's DONE interrupt to detect
completion. This interrupt is signaled when the TX FIFO becomes empty,
avoiding the need to busy-wait. However latency deteriorates compared
to the present commit and surprisingly, CPU time is slightly higher as
well:
It turns out that in 45% of the cases, no busy-waiting is needed at all
and in 76% of the cases, less than 10 busy-wait iterations are
sufficient for the TX FIFO to drain. This was measured on an RT kernel.
On a vanilla kernel, wakeup latency is worse and thus fewer iterations
are needed. The measurements were made with an SPI clock of 20 MHz,
they may differ slightly for slower or faster clock speeds.
Previously we always used the RX DMA interrupt to signal completion of a
transfer. Using the TX DMA interrupt now introduces a race condition:
TX DMA is always started before RX DMA so that bytes are already clocked
out while RX DMA is still being set up. But if a TX-only transfer is
very short, then the TX DMA interrupt may occur before RX DMA is set up.
If the interrupt happens to occur on the same CPU, setup of RX DMA may
even be delayed until after the interrupt was handled.
I've solved this by having the TX DMA callback clear the RX FIFO while
busy-waiting for the TX FIFO to drain, thus avoiding a dependency on
setup of RX DMA. Additionally, I am using a lock-free mechanism with
two flags, tx_dma_active and rx_dma_active plus memory barriers to
terminate RX DMA either by the TX DMA callback or immediately after
setting it up, whichever wins the race. I've explored an alternative
approach which temporarily disables the TX DMA callback until RX DMA
has been set up (using tasklet_disable(), local_bh_disable() or
local_irq_save()), but the performance was minimally worse.
[Nathan Chancellor contributed a DMA mapping fixup for an early version
of this commit, hence his Signed-off-by.]
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/874949385f28251e2dcaa9494e39a27b50e9f9e4.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 DMA controller is capable of synthesizing zeroes instead of
copying them from a source address. The feature is enabled by setting
the SRC_IGNORE bit in the Transfer Information field of a Control Block:
"Do not perform source reads.
In addition, destination writes will zero all the write strobes.
This is used for fast cache fill operations."
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
The feature is only available on 8 of the 16 channels. The others are
so-called "lite" channels with a limited feature set and performance.
Enable the feature if a cyclic transaction copies from the zero page.
This reduces traffic on the memory bus.
A forthcoming use case is the BCM2835 SPI driver, which will cyclically
copy from the zero page to the TX FIFO. The idea to use SRC_IGNORE was
taken from an ancient GitHub conversation between Martin and Noralf:
https://github.com/msperl/spi-bcm2835/issues/13#issuecomment-98180451
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/b2286c904408745192e4beb3de3c88f73e4a7210.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 SPI driver needs to set up the clock polarity in its
->prepare_message() hook before spi_transfer_one_message() asserts chip
select to avoid a gratuitous clock signal edge (cf. commit acace73df2c1
("spi: bcm2835: set up spi-mode before asserting cs-gpio")).
Precalculate the CS register value (which selects the clock polarity)
once in ->setup() and use that cached value in ->prepare_message() and
->transfer_one(). This avoids one MMIO read per message and one per
transfer, yielding a small latency improvement. Additionally, a
forthcoming commit will use the precalculated value to derive the
register value for clearing the RX FIFO, which will eliminate the need
for an RX dummy buffer when performing TX-only DMA transfers.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/d17c1d7fcdc97fffa961b8737cfd80eeb14f9416.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document the BCM2835 DMA driver's device data structure so that upcoming
commits may add further members with proper kerneldoc.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/78648f80f67d97bb7beecc1b9be6b6e4a45bc1d8.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
__spi_alloc_controller() uses a single allocation to accommodate struct
spi_controller and the driver-private data, but places the latter behind
the former. This order does not guarantee cacheline alignment of the
driver-private data. (It does guarantee cacheline alignment of struct
spi_controller but the structure doesn't make any use of that property.)
Round up struct spi_controller to cacheline size. A forthcoming commit
leverages this to grant DMA access to driver-private data of the BCM2835
SPI master.
An alternative, less economical approach would be to use two allocations.
A third approach consists of reversing the order to conserve memory.
But Mark Brown is concerned that it may result in a performance penalty
on architectures that don't like unaligned accesses.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/01625b9b26b93417fb09d2c15ad02dfe9cdbbbe5.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DMA engine API requires DMA drivers to explicitly allow that
descriptors are prepared once and reused multiple times. Only a
single driver makes use of this functionality so far (pxa_dma.c,
to speed up pxa_camera.c).
We're about to add another use case for reusable descriptors in
the BCM2835 SPI driver, so allow that in the BCM2835 DMA driver.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/bfc98a38225bbec4158440ad06cb9eee675e3e6f.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 DMA driver currently requests an interrupt from the
controller regardless whether or not the client has passed in the
DMA_PREP_INTERRUPT flag. This causes unnecessary overhead for cyclic
transactions which do not need an interrupt after each period.
We're about to add such a use case, namely cyclic clearing of the SPI
controller's RX FIFO, so amend the DMA driver to request an interrupt
only if DMA_PREP_INTERRUPT was passed in. Ignore the period_len for
such transactions and set it to the buffer length to make the driver's
calculations work.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/73cf37be56eb4cbe6f696057c719f3a38cbaf26e.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 SPI driver uses a flag to keep track of whether a DMA
transfer is in progress.
The flag is used to avoid terminating DMA channels multiple times if a
transfer finishes orderly while simultaneously the SPI core invokes the
->handle_err() callback because the transfer took too long. However
terminating DMA channels multiple times is perfectly fine, so the flag
is unnecessary for this particular purpose.
The flag is also used to avoid invoking bcm2835_spi_undo_prologue()
multiple times under this race condition. However multiple *concurrent*
invocations can no longer happen since commit 2527704d8411 ("spi:
bcm2835: Synchronize with callback on DMA termination") because the
->handle_err() callback now uses the _sync() variant when terminating
DMA channels.
The only raison d'être of the flag is therefore that
bcm2835_spi_undo_prologue() cannot cope with multiple *sequential*
invocations. Achieve that by setting tx_prologue to 0 at the end of
the function. Subsequent invocations thus become no-ops.
With that, the dma_pending flag becomes unnecessary, so drop it.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/062b03b7f86af77a13ce0ec3b22e0bdbfcfba10d.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Simplify this function implementation by using a known function.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b2dd074a-1693-3aea-42b4-da1f5ec155c4@web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This helps a bit with line fitting now (the list_first_entry call) as
well as during the next patch which needs to iterate through all
transfers of ctlr->cur_msg so it timestamps them.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
drivers/spi/spi-npcm-fiu.c: In function npcm_fiu_read:
drivers/spi/spi-npcm-fiu.c:472:9: warning:
variable retlen set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190905072436.23932-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-37-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-36-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-35-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-34-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-33-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-32-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-31-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-30-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-29-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-28-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-27-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-26-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-25-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-24-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-23-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-22-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-21-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-20-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-19-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-18-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190904135918.25352-17-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190904135918.25352-16-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-15-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-14-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-13-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-12-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-11-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-10-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-9-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-8-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-7-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-6-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-5-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-4-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-3-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-2-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a spelling mistake in a dev_warning message. Fix it. Also
break line to clear up checkpatch warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190903122812.3986-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the driver is working in TCFQ/EOQ mode (i.e. interacts with the SPI
controller's FIFOs directly) the following sequence of operations
happens:
- The first byte of the tx buffer gets pushed to the TX FIFO (dspi->len
gets decremented). This triggers the train of interrupts that handle
the rest of the bytes.
- The dspi_interrupt handles a TX confirmation event. It reads the newly
available byte from the RX FIFO, checks the dspi->len exit condition,
and if there's more to be done, it kicks off the next interrupt in the
train by writing the next byte to the TX FIFO.
Now the problem is that the wait queue is woken up one byte too early,
because dspi->len becomes 0 as soon as the byte has been pushed into the
TX FIFO. Its interrupt has not yet been processed and the RX byte has
not been put from the FIFO into the buffer.
Depending on the timing of the wait queue wakeup vs the handling of the
last dspi_interrupt, it can happen that the main SPI message pump thread
has already returned back into the spi_device driver. When the rx buffer
is on stack (which it can be, because in this mode, the DSPI doesn't do
DMA), the last interrupt will perform a memory write into an rx buffer
that has been freed. This manifests as stack corruption.
The solution is to only wake up the wait queue when dspi_rxtx says so,
i.e. after it has processed the last TX confirmation interrupt and
collected the last RX byte.
Fixes: c55be3059159 ("spi: spi-fsl-dspi: Use poll mode in case the platform IRQ is missing")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190903105708.32273-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Introduce new polling mode for short size transfer. Either the estimated
transfer time is estimated to exceed 200us, or polling loop actually exceeds
200us, it switches to irq mode.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Link: https://lore.kernel.org/r/1567488661-11428-4-git-send-email-hayashibara.keiji@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
