| Age | Commit message (Collapse) | Author |
|---|
|
The code does:
if (hrtimer_active(&t))
hrtimer_cancel(&t);
However, hrtimer_cancel() checks if the timer is active, so the
test above is pointless.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in the following script
# tc actions add action ife encode allow prio pass index 42
# tc actions replace action ife encode allow tcindex drop index 42
the action control should remain equal to 'pass', if the kernel failed
to replace the TC action. Pospone the assignment of the action control,
to ensure it is not overwritten in the error path of tcf_ife_init().
Fixes: ef6980b6becb ("introduce IFE action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
a recursive lock warning [1] can be observed with the following script,
# $TC actions add action ife encode allow prio pass index 42
IFE type 0xED3E
# $TC actions replace action ife encode allow tcindex pass index 42
in case the kernel was unable to run the last command (e.g. because of
the impossibility to load 'act_meta_skbtcindex'). For a similar reason,
the kernel can leak idr in the error path of tcf_ife_init(), because
tcf_idr_release() is not called after successful idr reservation:
# $TC actions add action ife encode allow tcindex index 47
IFE type 0xED3E
RTNETLINK answers: No such file or directory
We have an error talking to the kernel
# $TC actions add action ife encode allow tcindex index 47
IFE type 0xED3E
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# $TC actions add action ife encode use mark 7 type 0xfefe pass index 47
IFE type 0xFEFE
RTNETLINK answers: No space left on device
We have an error talking to the kernel
Since tcfa_lock is already taken when the action is being edited, a call
to tcf_idr_release() wrongly makes tcf_idr_cleanup() take the same lock
again. On the other hand, tcf_idr_release() needs to be called in the
error path of tcf_ife_init(), to undo the last tcf_idr_create() invocation.
Fix both problems in tcf_ife_init().
Since the cleanup() routine can now be called when ife->params is NULL,
also add a NULL pointer check to avoid calling kfree_rcu(NULL, rcu).
[1]
============================================
WARNING: possible recursive locking detected
4.17.0-rc4.kasan+ #417 Tainted: G E
--------------------------------------------
tc/3932 is trying to acquire lock:
000000005097c9a6 (&(&p->tcfa_lock)->rlock){+...}, at: tcf_ife_cleanup+0x19/0x80 [act_ife]
but task is already holding lock:
000000005097c9a6 (&(&p->tcfa_lock)->rlock){+...}, at: tcf_ife_init+0xf6d/0x13c0 [act_ife]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&p->tcfa_lock)->rlock);
lock(&(&p->tcfa_lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by tc/3932:
#0: 000000007ca8e990 (rtnl_mutex){+.+.}, at: tcf_ife_init+0xf61/0x13c0 [act_ife]
#1: 000000005097c9a6 (&(&p->tcfa_lock)->rlock){+...}, at: tcf_ife_init+0xf6d/0x13c0 [act_ife]
stack backtrace:
CPU: 3 PID: 3932 Comm: tc Tainted: G E 4.17.0-rc4.kasan+ #417
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Call Trace:
dump_stack+0x9a/0xeb
__lock_acquire+0xf43/0x34a0
? debug_check_no_locks_freed+0x2b0/0x2b0
? debug_check_no_locks_freed+0x2b0/0x2b0
? debug_check_no_locks_freed+0x2b0/0x2b0
? __mutex_lock+0x62f/0x1240
? kvm_sched_clock_read+0x1a/0x30
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x170
? find_held_lock+0x39/0x1d0
? lock_acquire+0x10b/0x330
lock_acquire+0x10b/0x330
? tcf_ife_cleanup+0x19/0x80 [act_ife]
_raw_spin_lock_bh+0x38/0x70
? tcf_ife_cleanup+0x19/0x80 [act_ife]
tcf_ife_cleanup+0x19/0x80 [act_ife]
__tcf_idr_release+0xff/0x350
tcf_ife_init+0xdde/0x13c0 [act_ife]
? ife_exit_net+0x290/0x290 [act_ife]
? __lock_is_held+0xb4/0x140
tcf_action_init_1+0x67b/0xad0
? tcf_action_dump_old+0xa0/0xa0
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x170
? kvm_sched_clock_read+0x1a/0x30
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x170
? memset+0x1f/0x40
tcf_action_init+0x30f/0x590
? tcf_action_init_1+0xad0/0xad0
? memset+0x1f/0x40
tc_ctl_action+0x48e/0x5e0
? mutex_lock_io_nested+0x1160/0x1160
? tca_action_gd+0x990/0x990
? sched_clock+0x5/0x10
? find_held_lock+0x39/0x1d0
rtnetlink_rcv_msg+0x4da/0x990
? validate_linkmsg+0x680/0x680
? sched_clock_cpu+0x18/0x170
? find_held_lock+0x39/0x1d0
netlink_rcv_skb+0x127/0x350
? validate_linkmsg+0x680/0x680
? netlink_ack+0x970/0x970
? __kmalloc_node_track_caller+0x304/0x3a0
netlink_unicast+0x40f/0x5d0
? netlink_attachskb+0x580/0x580
? _copy_from_iter_full+0x187/0x760
? import_iovec+0x90/0x390
netlink_sendmsg+0x67f/0xb50
? netlink_unicast+0x5d0/0x5d0
? copy_msghdr_from_user+0x206/0x340
? netlink_unicast+0x5d0/0x5d0
sock_sendmsg+0xb3/0xf0
___sys_sendmsg+0x60a/0x8b0
? copy_msghdr_from_user+0x340/0x340
? lock_downgrade+0x5e0/0x5e0
? tty_write_lock+0x18/0x50
? kvm_sched_clock_read+0x1a/0x30
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x170
? find_held_lock+0x39/0x1d0
? lock_downgrade+0x5e0/0x5e0
? lock_acquire+0x10b/0x330
? __audit_syscall_entry+0x316/0x690
? current_kernel_time64+0x6b/0xd0
? __fget_light+0x55/0x1f0
? __sys_sendmsg+0xd2/0x170
__sys_sendmsg+0xd2/0x170
? __ia32_sys_shutdown+0x70/0x70
? syscall_trace_enter+0x57a/0xd60
? rcu_read_lock_sched_held+0xdc/0x110
? __bpf_trace_sys_enter+0x10/0x10
? do_syscall_64+0x22/0x480
do_syscall_64+0xa5/0x480
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fd646988ba0
RSP: 002b:00007fffc9fab3c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fffc9fab4f0 RCX: 00007fd646988ba0
RDX: 0000000000000000 RSI: 00007fffc9fab440 RDI: 0000000000000003
RBP: 000000005b28c8b3 R08: 0000000000000002 R09: 0000000000000000
R10: 00007fffc9faae20 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffc9fab504 R14: 0000000000000001 R15: 000000000066c100
Fixes: 4e8c86155010 ("net sched: net sched: ife action fix late binding")
Fixes: ef6980b6becb ("introduce IFE action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts commit 3243ff2a05ec ("net: ethernet: davinci_emac:
Deduplicate bus_find_device() by name matching") and adds a comment
which should stop anyone from reintroducing the same "fix" in the future.
We can't use bus_find_device_by_name() here because the device name is
not guaranteed to be 'davinci_mdio'. On some systems it can be
'davinci_mdio.0' so we need to use strncmp() against the first part of
the string to correctly match it.
Fixes: 3243ff2a05ec ("net: ethernet: davinci_emac: Deduplicate bus_find_device() by name matching")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With 4k page size for hugetlb we allocate hugepage directories from its on slab
cache. With patch 0c4d26802 ("powerpc/book3s64/mm: Simplify the rcu callback for page table free")
we missed to free these allocated hugepd tables.
Update pgtable_free to handle hugetlb hugepd directory table.
Fixes: 0c4d268029bf ("powerpc/book3s64/mm: Simplify the rcu callback for page table free")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Add CONFIG_HUGETLB_PAGE guard to fix build break]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
possible CPU
If possible CPUs are limited (e.g., by kexec), then the kvm prefetch
workaround function can access the paca pointer for a !possible CPU.
Fixes: d2e60075a3d44 ("powerpc/64: Use array of paca pointers and allocate pacas individually")
Cc: stable@kernel.org
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Tested-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
if dev_get_valid_name failed, propagate its return code
and remove the setting err to ENODEV, it will be set to
0 again before dev_change_net_namespace exits.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In failure path, we overwrite err to what vnic_rq_disable() returns. In
case it returns 0, enic_open() returns success in case of error.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Fixes: e8588e268509 ("enic: enable rq before updating rq descriptors")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to 69678bcd4d2d ("udp: fix SO_BINDTODEVICE"), TCP socket lookups
need to fail if dev_match is not true. Currently, a packet to a given port
can match a socket bound to device when it should not. In the VRF case,
this causes the lookup to hit a VRF socket and not a global socket
resulting in a response trying to go through the VRF when it should not.
Fixes: 3fa6f616a7a4d ("net: ipv4: add second dif to inet socket lookups")
Fixes: 4297a0ef08572 ("net: ipv6: add second dif to inet6 socket lookups")
Reported-by: Lou Berger <lberger@labn.net>
Diagnosed-by: Renato Westphal <renato@opensourcerouting.org>
Tested-by: Renato Westphal <renato@opensourcerouting.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
getnstimeofday64() is deprecated and getting replaced throughout
the kernel with ktime_get_*() based helpers for a more consistent
interface.
The two functions do the exact same thing, so this is just
a cosmetic change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported use after free that is caused by fib6_info being
freed without a proper RCU grace period.
CPU: 0 PID: 1407 Comm: udevd Not tainted 4.17.0+ #39
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1b9/0x294 lib/dump_stack.c:113
print_address_description+0x6c/0x20b mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
__read_once_size include/linux/compiler.h:188 [inline]
find_rr_leaf net/ipv6/route.c:705 [inline]
rt6_select net/ipv6/route.c:761 [inline]
fib6_table_lookup+0x12b7/0x14d0 net/ipv6/route.c:1823
ip6_pol_route+0x1c2/0x1020 net/ipv6/route.c:1856
ip6_pol_route_output+0x54/0x70 net/ipv6/route.c:2082
fib6_rule_lookup+0x211/0x6d0 net/ipv6/fib6_rules.c:122
ip6_route_output_flags+0x2c5/0x350 net/ipv6/route.c:2110
ip6_route_output include/net/ip6_route.h:82 [inline]
icmpv6_xrlim_allow net/ipv6/icmp.c:211 [inline]
icmp6_send+0x147c/0x2da0 net/ipv6/icmp.c:535
icmpv6_send+0x17a/0x300 net/ipv6/ip6_icmp.c:43
ip6_link_failure+0xa5/0x790 net/ipv6/route.c:2244
dst_link_failure include/net/dst.h:427 [inline]
ndisc_error_report+0xd1/0x1c0 net/ipv6/ndisc.c:695
neigh_invalidate+0x246/0x550 net/core/neighbour.c:892
neigh_timer_handler+0xaf9/0xde0 net/core/neighbour.c:978
call_timer_fn+0x230/0x940 kernel/time/timer.c:1326
expire_timers kernel/time/timer.c:1363 [inline]
__run_timers+0x79e/0xc50 kernel/time/timer.c:1666
run_timer_softirq+0x4c/0x70 kernel/time/timer.c:1692
__do_softirq+0x2e0/0xaf5 kernel/softirq.c:284
invoke_softirq kernel/softirq.c:364 [inline]
irq_exit+0x1d1/0x200 kernel/softirq.c:404
exiting_irq arch/x86/include/asm/apic.h:527 [inline]
smp_apic_timer_interrupt+0x17e/0x710 arch/x86/kernel/apic/apic.c:1052
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:863
</IRQ>
RIP: 0010:strlen+0x5e/0xa0 lib/string.c:482
Code: 24 00 74 3b 48 bb 00 00 00 00 00 fc ff df 4c 89 e0 48 83 c0 01 48 89 c2 48 89 c1 48 c1 ea 03 83 e1 07 0f b6 14 1a 38 ca 7f 04 <84> d2 75 23 80 38 00 75 de 48 83 c4 08 4c 29 e0 5b 41 5c 5d c3 48
RSP: 0018:ffff8801af117850 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff13
RAX: ffff880197f53bd0 RBX: dffffc0000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff81c5b06c RDI: ffff880197f53bc0
RBP: ffff8801af117868 R08: ffff88019a976540 R09: 0000000000000000
R10: ffff88019a976540 R11: 0000000000000000 R12: ffff880197f53bc0
R13: ffff880197f53bc0 R14: ffffffff899e4e90 R15: ffff8801d91c6a00
strlen include/linux/string.h:267 [inline]
getname_kernel+0x24/0x370 fs/namei.c:218
open_exec+0x17/0x70 fs/exec.c:882
load_elf_binary+0x968/0x5610 fs/binfmt_elf.c:780
search_binary_handler+0x17d/0x570 fs/exec.c:1653
exec_binprm fs/exec.c:1695 [inline]
__do_execve_file.isra.35+0x16fe/0x2710 fs/exec.c:1819
do_execveat_common fs/exec.c:1866 [inline]
do_execve fs/exec.c:1883 [inline]
__do_sys_execve fs/exec.c:1964 [inline]
__se_sys_execve fs/exec.c:1959 [inline]
__x64_sys_execve+0x8f/0xc0 fs/exec.c:1959
do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f1576a46207
Code: 77 19 f4 48 89 d7 44 89 c0 0f 05 48 3d 00 f0 ff ff 76 e0 f7 d8 64 41 89 01 eb d8 f7 d8 64 41 89 01 eb df b8 3b 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 02 f3 c3 48 8b 15 00 8c 2d 00 f7 d8 64 89 02
RSP: 002b:00007ffff2784568 EFLAGS: 00000202 ORIG_RAX: 000000000000003b
RAX: ffffffffffffffda RBX: 00000000ffffffff RCX: 00007f1576a46207
RDX: 0000000001215b10 RSI: 00007ffff2784660 RDI: 00007ffff2785670
RBP: 0000000000625500 R08: 000000000000589c R09: 000000000000589c
R10: 0000000000000000 R11: 0000000000000202 R12: 0000000001215b10
R13: 0000000000000007 R14: 0000000001204250 R15: 0000000000000005
Allocated by task 12188:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xc4/0xe0 mm/kasan/kasan.c:553
kmem_cache_alloc_trace+0x152/0x780 mm/slab.c:3620
kmalloc include/linux/slab.h:513 [inline]
kzalloc include/linux/slab.h:706 [inline]
fib6_info_alloc+0xbb/0x280 net/ipv6/ip6_fib.c:152
ip6_route_info_create+0x782/0x2b50 net/ipv6/route.c:3013
ip6_route_add+0x23/0xb0 net/ipv6/route.c:3154
ipv6_route_ioctl+0x5a5/0x760 net/ipv6/route.c:3660
inet6_ioctl+0x100/0x1f0 net/ipv6/af_inet6.c:546
sock_do_ioctl+0xe4/0x3e0 net/socket.c:973
sock_ioctl+0x30d/0x680 net/socket.c:1097
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:500 [inline]
do_vfs_ioctl+0x1cf/0x16f0 fs/ioctl.c:684
ksys_ioctl+0xa9/0xd0 fs/ioctl.c:701
__do_sys_ioctl fs/ioctl.c:708 [inline]
__se_sys_ioctl fs/ioctl.c:706 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:706
do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 1402:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free+0x11a/0x170 mm/kasan/kasan.c:521
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xd9/0x260 mm/slab.c:3813
fib6_info_destroy+0x29b/0x350 net/ipv6/ip6_fib.c:207
fib6_info_release include/net/ip6_fib.h:286 [inline]
__ip6_del_rt_siblings net/ipv6/route.c:3235 [inline]
ip6_route_del+0x11c4/0x13b0 net/ipv6/route.c:3316
ipv6_route_ioctl+0x616/0x760 net/ipv6/route.c:3663
inet6_ioctl+0x100/0x1f0 net/ipv6/af_inet6.c:546
sock_do_ioctl+0xe4/0x3e0 net/socket.c:973
sock_ioctl+0x30d/0x680 net/socket.c:1097
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:500 [inline]
do_vfs_ioctl+0x1cf/0x16f0 fs/ioctl.c:684
ksys_ioctl+0xa9/0xd0 fs/ioctl.c:701
__do_sys_ioctl fs/ioctl.c:708 [inline]
__se_sys_ioctl fs/ioctl.c:706 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:706
do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8801b5df2580
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 8 bytes inside of
256-byte region [ffff8801b5df2580, ffff8801b5df2680)
The buggy address belongs to the page:
page:ffffea0006d77c80 count:1 mapcount:0 mapping:ffff8801da8007c0 index:0xffff8801b5df2e40
flags: 0x2fffc0000000100(slab)
raw: 02fffc0000000100 ffffea0006c5cc48 ffffea0007363308 ffff8801da8007c0
raw: ffff8801b5df2e40 ffff8801b5df2080 0000000100000006 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801b5df2480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8801b5df2500: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
> ffff8801b5df2580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8801b5df2600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8801b5df2680: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
Fixes: a64efe142f5e ("net/ipv6: introduce fib6_info struct and helpers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@gmail.com>
Reported-by: syzbot+9e6d75e3edef427ee888@syzkaller.appspotmail.com
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sync both unicast and multicast lists instead of unicast twice.
Fixes: cfc80d9a116 ("net: Introduce net_failover driver")
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to the fixes on team and bonding, this restores the ability
to set an ipvlan device's mtu to anything higher than 1500.
Fixes: 91572088e3fd ("net: use core MTU range checking in core net infra")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The array bpq_eth_addr is only used to get the size of an
address, whereas the bcast_addr is used to set the broadcast
address. This leads to a warning when using clang:
drivers/net/hamradio/bpqether.c:94:13: warning: variable 'bpq_eth_addr' is not
needed and will not be emitted [-Wunneeded-internal-declaration]
static char bpq_eth_addr[6];
^
Remove both variables and use the common eth_broadcast_addr
to set the broadcast address.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lockdep spotted that we are using rfs_h.lock in enic_get_rxnfc() without
initializing. rfs_h.lock is initialized in enic_open(). But ethtool_ops
can be called when interface is down.
Move enic_rfs_flw_tbl_init to enic_probe.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 18 PID: 1189 Comm: ethtool Not tainted 4.17.0-rc7-devel+ #27
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
Call Trace:
dump_stack+0x85/0xc0
register_lock_class+0x550/0x560
? __handle_mm_fault+0xa8b/0x1100
__lock_acquire+0x81/0x670
lock_acquire+0xb9/0x1e0
? enic_get_rxnfc+0x139/0x2b0 [enic]
_raw_spin_lock_bh+0x38/0x80
? enic_get_rxnfc+0x139/0x2b0 [enic]
enic_get_rxnfc+0x139/0x2b0 [enic]
ethtool_get_rxnfc+0x8d/0x1c0
dev_ethtool+0x16c8/0x2400
? __mutex_lock+0x64d/0xa00
? dev_load+0x6a/0x150
dev_ioctl+0x253/0x4b0
sock_do_ioctl+0x9a/0x130
sock_ioctl+0x1af/0x350
do_vfs_ioctl+0x8e/0x670
? syscall_trace_enter+0x1e2/0x380
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x5a/0x170
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Joel Stanley says:
====================
Slience NCSI logging
v2:
Fix indent issue and commit message based on Joe's feedback
Add Sam's acks
Here are three changes to silence unnecessary warnings in the ncsi code.
The final patch adds Sam as the maintainer for NCSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sam has been handing the maintenance of NCSI for a number release cycles
now.
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This moves all of the netdev_printk(KERN_DEBUG, ...) messages over to
netdev_dbg.
As Joe explains:
> netdev_dbg is not included in object code unless
> DEBUG is defined or CONFIG_DYNAMIC_DEBUG is set.
> And then, it is not emitted into the log unless
> DEBUG is set or this specific netdev_dbg is enabled
> via the dynamic debug control file.
Which is what we're after in this case.
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This does not provide useful information. As the ncsi maintainer said:
> either we get a channel or broadcom has gone out to lunch
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In normal operation we see this series of messages as the host drives
the network device:
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
ftgmac100 1e660000.ethernet eth0: NCSI interface down
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI interface up
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
ftgmac100 1e660000.ethernet eth0: NCSI interface down
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI interface up
This makes all of these messages netdev_dbg. They are still useful to
debug eg. misbehaving network device firmware, but we do not need them
filling up the kernel logs in normal operation.
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using skb_reserve(skb, I40E_SKB_PAD + (xdp->data - xdp->data_hard_start))
is clearly wrong since I40E_SKB_PAD already points to the offset where
the original xdp->data was sitting since xdp->data_hard_start is defined
as xdp->data - i40e_rx_offset(rx_ring) where latter offsets to I40E_SKB_PAD
when build skb is used.
However, also before cc5b114dcf98 ("bpf, i40e: add meta data support")
this seems broken since bpf_xdp_adjust_head() helper could have been used
to alter headroom and enlarge / shrink the frame and with that the assumption
that the xdp->data remains unchanged does not hold and would push a bogus
packet to upper stack.
ixgbe got this right in 924708081629 ("ixgbe: add XDP support for pass and
drop actions"). In any case, fix it by removing the I40E_SKB_PAD from both
skb_reserve() and truesize calculation.
Fixes: cc5b114dcf98 ("bpf, i40e: add meta data support")
Fixes: 0c8493d90b6b ("i40e: add XDP support for pass and drop actions")
Reported-by: Keith Busch <keith.busch@linux.intel.com>
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Tested-by: Keith Busch <keith.busch@linux.intel.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sudarsana Reddy Kalluru says:
====================
qed*: Fix series.
The patch series fixes few issues in the qed/qede drivers.
Please consider applying this series to "net".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not advertise DCBX_LLD_MANAGED capability i.e., do not allow
external agent to manage the dcbx/lldp negotiation. MFW acts as lldp agent
for qed* devices, and no other lldp agent is allowed to coexist with mfw.
Also updated a debug print, to not to display the redundant info.
Fixes: a1d8d8a51 ("qed: Add dcbnl support.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid calling a SIMD fastpath handler if it is NULL. The check is needed
to handle an unlikely scenario where unsolicited interrupt is destined to
a PF in INTa mode.
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Memory for packet buffers need to be freed in the error paths as there is
no consumer (e.g., upper layer) for such packets and that memory will never
get freed.
The issue was uncovered when port was attacked with flood of isatap
packets, these are multicast packets hence were directed at all the PFs.
For foce PF, this meant they were routed to the ll2 module which in turn
drops such packets.
Fixes: 0a7fb11c ("qed: Add Light L2 support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ftrace_graph_caller was never run after calling ftrace_trace_function,
breaking the function graph tracer. Fix this, bringing it in line with the
x86 implementation.
While we're at it, also streamline the control flow of _mcount a bit to
reduce the number of branches.
This issue was reported before:
https://www.linux-mips.org/archives/linux-mips/2014-11/msg00295.html
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Tested-by: Matt Redfearn <matt.redfearn@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/18929/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: stable@vger.kernel.org # v3.17+
|
|
Even BOs with AMDGPU_GEM_CREATE_NO_CPU_ACCESS may end up at least
partially in CPU visible VRAM, in particular when all VRAM is visible.
v2:
* Don't take VRAM mgr spinlock, not needed (Christian König)
* Make loop logic simpler and clearer.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Preparation for the following fix, no functional change intended.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
At least in theory, ttm_bo_validate may move the BO, in which case the
pin_size accounting would be inconsistent with when the BO was pinned.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
All UVD instanses have only one dpm control, so it is better
to share one idle_work handle.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Commit 0ba99ca4838b ("block: Add warning for bi_next not NULL in
bio_endio()") breaks the dm driver. end_clone_bio() detects whether
or not a bio is the last bio associated with a request by checking
the .bi_next field. Commit 0ba99ca4838b clears that field before
end_clone_bio() has had a chance to inspect that field. Hence revert
commit 0ba99ca4838b.
This patch avoids that KASAN reports the following complaint when
running the srp-test software (srp-test/run_tests -c -d -r 10 -t 02-mq):
==================================================================
BUG: KASAN: use-after-free in bio_advance+0x11b/0x1d0
Read of size 4 at addr ffff8801300e06d0 by task ksoftirqd/0/9
CPU: 0 PID: 9 Comm: ksoftirqd/0 Not tainted 4.18.0-rc1-dbg+ #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0xa4/0xf5
print_address_description+0x6f/0x270
kasan_report+0x241/0x360
__asan_load4+0x78/0x80
bio_advance+0x11b/0x1d0
blk_update_request+0xa7/0x5b0
scsi_end_request+0x56/0x320 [scsi_mod]
scsi_io_completion+0x7d6/0xb20 [scsi_mod]
scsi_finish_command+0x1c0/0x280 [scsi_mod]
scsi_softirq_done+0x19a/0x230 [scsi_mod]
blk_mq_complete_request+0x160/0x240
scsi_mq_done+0x50/0x1a0 [scsi_mod]
srp_recv_done+0x515/0x1330 [ib_srp]
__ib_process_cq+0xa0/0xf0 [ib_core]
ib_poll_handler+0x38/0xa0 [ib_core]
irq_poll_softirq+0xe8/0x1f0
__do_softirq+0x128/0x60d
run_ksoftirqd+0x3f/0x60
smpboot_thread_fn+0x352/0x460
kthread+0x1c1/0x1e0
ret_from_fork+0x24/0x30
Allocated by task 1918:
save_stack+0x43/0xd0
kasan_kmalloc+0xad/0xe0
kasan_slab_alloc+0x11/0x20
kmem_cache_alloc+0xfe/0x350
mempool_alloc_slab+0x15/0x20
mempool_alloc+0xfb/0x270
bio_alloc_bioset+0x244/0x350
submit_bh_wbc+0x9c/0x2f0
__block_write_full_page+0x299/0x5a0
block_write_full_page+0x16b/0x180
blkdev_writepage+0x18/0x20
__writepage+0x42/0x80
write_cache_pages+0x376/0x8a0
generic_writepages+0xbe/0x110
blkdev_writepages+0xe/0x10
do_writepages+0x9b/0x180
__filemap_fdatawrite_range+0x178/0x1c0
file_write_and_wait_range+0x59/0xc0
blkdev_fsync+0x46/0x80
vfs_fsync_range+0x66/0x100
do_fsync+0x3d/0x70
__x64_sys_fsync+0x21/0x30
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 9:
save_stack+0x43/0xd0
__kasan_slab_free+0x137/0x190
kasan_slab_free+0xe/0x10
kmem_cache_free+0xd3/0x380
mempool_free_slab+0x17/0x20
mempool_free+0x63/0x160
bio_free+0x81/0xa0
bio_put+0x59/0x60
end_bio_bh_io_sync+0x5d/0x70
bio_endio+0x1a7/0x360
blk_update_request+0xd0/0x5b0
end_clone_bio+0xa3/0xd0 [dm_mod]
bio_endio+0x1a7/0x360
blk_update_request+0xd0/0x5b0
scsi_end_request+0x56/0x320 [scsi_mod]
scsi_io_completion+0x7d6/0xb20 [scsi_mod]
scsi_finish_command+0x1c0/0x280 [scsi_mod]
scsi_softirq_done+0x19a/0x230 [scsi_mod]
blk_mq_complete_request+0x160/0x240
scsi_mq_done+0x50/0x1a0 [scsi_mod]
srp_recv_done+0x515/0x1330 [ib_srp]
__ib_process_cq+0xa0/0xf0 [ib_core]
ib_poll_handler+0x38/0xa0 [ib_core]
irq_poll_softirq+0xe8/0x1f0
__do_softirq+0x128/0x60d
The buggy address belongs to the object at ffff8801300e0640
which belongs to the cache bio-0 of size 200
The buggy address is located 144 bytes inside of
200-byte region [ffff8801300e0640, ffff8801300e0708)
The buggy address belongs to the page:
page:ffffea0004c03800 count:1 mapcount:0 mapping:ffff88015a563a00 index:0x0 compound_mapcount: 0
flags: 0x8000000000008100(slab|head)
raw: 8000000000008100 dead000000000100 dead000000000200 ffff88015a563a00
raw: 0000000000000000 0000000000330033 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801300e0580: fb fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc
ffff8801300e0600: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
>ffff8801300e0680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8801300e0700: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8801300e0780: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Fixes: 0ba99ca4838b ("block: Add warning for bi_next not NULL in bio_endio()")
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We've had a number of users report failures to detect and light up
display with DC with LVDS and VGA. These connector types are not
currently supported with DC. I'd like to add support but unfortunately
don't have a system with LVDS or VGA available.
In order not to cause regressions we should probably fallback to the
non-DC driver for ASICs that support VGA and LVDS.
These ASICs are:
* Bonaire
* Kabini
* Kaveri
* Mullins
ASIC support can always be force enabled with amdgpu.dc=1
v2: Keep Hawaii on DC
v3: Added Mullins to the list
Cc: stable@vger.kernel.org
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It can be quite big, and there's no need for it to be physically
contiguous. This is less likely to fail under memory pressure (has
actually happened while running piglit).
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Initialize variable to 0 before performing logical OR operation.
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Rajan Vaja <rajan.vaja@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
blk_mq_complete_request can only be called for blk-mq drivers, but when
removing the BLK_EH_HANDLED return value, two legacy request timeout
methods incorrectly got switched to call blk_mq_complete_request.
Call __blk_complete_request instead to reinstance the previous behavior.
For that __blk_complete_request needs to be exported.
Fixes: 1fc2b62e ("scsi_transport_fc: complete requests from ->timeout")
Fixes: 0df0bb08 ("null_blk: complete requests from ->timeout")
Reported-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull an OPP fix for 4.18-rc2 from Viresh Kumar.
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
PM / OPP: Update voltage in case freq == old_freq
|
|
Although the writeback resends are more robust than the reads, since they
are not immediately rescheduled by the same thread, we are better off
processing them in the same place as the reads.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
We do not want to have rpciod threads perform recursive calls into the
RPC layer since that can deadlock. In particular, having to wait for
a layoutget can be nasty... We want rather to defer scheduling those
retries until we're in the rpc_release() callback, since that is
called from the nfsiod workqueue.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
We can't call function trace hook before setup percpu offset.
When entering secondary_start_kernel(), percpu offset has not
been initialized. So this lead hotplug malfunction.
Here is the flow to reproduce this bug:
echo 0 > /sys/devices/system/cpu/cpu1/online
echo function > /sys/kernel/debug/tracing/current_tracer
echo 1 > /sys/kernel/debug/tracing/tracing_on
echo 1 > /sys/devices/system/cpu/cpu1/online
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Zhizhou Zhang <zhizhouzhang@asrmicro.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
dma_alloc_*() buffers might be exposed to userspace via mmap() call, so
they should be cleared on allocation. In case of IOMMU-based dma-mapping
implementation such buffer clearing was missing in the code path for
DMA_ATTR_FORCE_CONTIGUOUS flag handling, because dma_alloc_from_contiguous()
doesn't honor __GFP_ZERO flag. This patch fixes this issue. For more
information on clearing buffers allocated by dma_alloc_* functions,
see commit 6829e274a623 ("arm64: dma-mapping: always clear allocated
buffers").
Fixes: 44176bb38fa4 ("arm64: Add support for DMA_ATTR_FORCE_CONTIGUOUS to IOMMU")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
I broke the build when CONFIG_NMI_IPI=n with my recent commit to add
arch_trigger_cpumask_backtrace(), eg:
stacktrace.c:(.text+0x1b0): undefined reference to `.smp_send_safe_nmi_ipi'
We should rework the CONFIG symbols here in future to avoid these
double barrelled ifdefs but for now they fix the build.
Fixes: 5cc05910f26e ("powerpc/64s: Wire up arch_trigger_cpumask_backtrace()")
Reported-by: Christophe LEROY <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When xenbus_printf fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling xenbus_printf.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
When xenbus_printf fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling xenbus_printf.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Krzysztof Kozlowski <krzk@kernel.org> reports that a heavy NFSv4
WRITE workload against a slow NFS server causes his Raspberry Pi
clients to stall. Krzysztof bisected it to commit 37ac86c3a76c
("SUNRPC: Initialize rpc_rqst outside of xprt->reserve_lock") .
I was able to reproduce similar behavior and it appears that rarely
the RPC client layer is re-allocating an XID for an RPC that it has
already partially sent. This results in the client ignoring the
subsequent reply, which carries the original XID.
For various reasons, checking !req->rq_xmit_bytes_sent in
xprt_prepare_transmit is not a 100% reliable mechanism for
determining when a fresh XID is needed.
Trond's preference is to allocate the XID at the time each rpc_rqst
slot is initialized.
This patch should also address a gcc 4.1.2 complaint reported by
Geert Uytterhoeven <geert@linux-m68k.org>.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 37ac86c3a76c ("SUNRPC: Initialize rpc_rqst outside of ... ")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
If the layout was invalidated due to a reboot, then don't try to send
a layoutreturn for it.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
Right now, we can call nfs_commit_inode() while holding the session slot,
which could lead to NFSv4 deadlocks. Ensure we only keep the slot if
the server returned a layout that we have to process.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
The SF and clipper units mishandle the provoking vertex in some cases,
which can cause misrendering with shaders that use flat shaded inputs.
There are chicken bits in 3D_CHICKEN3 (for SF) and FF_SLICE_CHICKEN
(for the clipper) that work around the issue. These registers are
unfortunately not part of the logical context (even the power context),
and so we must reload them every time we start executing in a context.
Bugzilla: https://bugs.freedesktop.org/103047
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615190605.16238-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
(cherry picked from commit b77422f80337d363eed60c8c48db9cb6e33085c9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If client is smart or lucky enough to create a new context
after each hang, our context banning mechanism will never
catch up, and as a result of that it will be saved from
client banning. This can result in a never ending streak of
gpu hangs caused by bad or malicious client, preventing
access from other legit gpu clients.
Fix this by always incrementing per client ban score if
it hangs in short successions regardless of context ban
scoring. The exception are non bannable contexts. They remain
detached from client ban scoring mechanism.
v2: xchg timestamp, tidyup (Chris)
v3: comment, bannable & banned together (Chris)
Fixes: b083a0870c79 ("drm/i915: Add per client max context ban limit")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615104429.31477-1-mika.kuoppala@linux.intel.com
(cherry picked from commit 14921f3cef85b0167a9145e5f29b9dfc3b2a84dc)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
While Bspec doesn't list a specific sequence for turning off the DP port
on g4x we are getting an underrun if the port is disabled in the
.disable() hook. Looks like the pipe stops when the port stops, and by
that time the plane disable may not have completed yet. Also the plane(s)
seem to end up in some wonky state when this happens as they also signal
another underrun immediately after we turn them back on during the next
enable sequence.
We could add a vblank wait in .disable() to avoid wedging the planes,
but I assume we're still tripping up the pipe in some way. So it seems
better to me to just follow the ILK+ sequence and turn off the DP port
in .post_disable() instead. This sequence doesn't seem to suffer from
this problem. Could be it was always the intended sequence for DP and
the gen4 bspec was just never updated to include it.
Originally we used the bad sequence even on ilk+, but I changed that
in commit 08aff3fe26ae ("drm/i915: Move DP port disable to post_disable
for pch platforms") as it was causing issues on those platforms as well.
I left out g4x then only because I didn't have the hardware to test it.
Now that I do it's fairly clear that the ilk+ sequence is also the
right choice for g4x.
v2: Fix whitespace fail (Jani)
Mention the ilk+ commit (Jani)
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 51a9f6dfc00d35f927ecfaf6f0ae8ebaba39b3fe)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Looks like interlaced DP output doesn't work on g4x either. Not all
that surprising considering we already established that interlaced
DP output is busted on VLV/CHV.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-1-ville.syrjala@linux.intel.com
(cherry picked from commit 929168c5f3df5d9ea0ef426c33e971157d045eab)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
