| Age | Commit message (Collapse) | Author |
|---|
|
Dave has not been very active on arch/sparc for the past two years.
I have been contributing to the SPARC32 port as well as maintaining
out-of-tree SPARC32 patches for LEON3/4/5 (SPARCv8 with CAS support)
since 2012. I am willing to step up as an arch/sparc (co-)maintainer.
For recent discussions on the matter, see [1] and [2].
[1] https://lore.kernel.org/r/20230713075235.2164609-1-u.kleine-koenig@pengutronix.de
[2] https://lore.kernel.org/r/20231209105816.GA1085691@ravnborg.org/
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Acked-by: Jose E. Marchesi <jose.marchesi@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The FORCE_STOP_STATE bit is unsuitable to force the DSI link into LP-11
mode. It seems the bridge internally queues DSI packets and when the
FORCE_STOP_STATE bit is cleared, they are sent in close succession
without any useful timing (this also means that the DSI lanes won't go
into LP-11 mode). The length of this gibberish varies between 1ms and
5ms. This sometimes breaks an attached bridge (TI SN65DSI84 in this
case). In our case, the bridge will fail in about 1 per 500 reboots.
The FORCE_STOP_STATE handling was introduced to have the DSI lanes in
LP-11 state during the .pre_enable phase. But as it turns out, none of
this is needed at all. Between samsung_dsim_init() and
samsung_dsim_set_display_enable() the lanes are already in LP-11 mode.
The code as it was before commit 20c827683de0 ("drm: bridge:
samsung-dsim: Fix init during host transfer") and 0c14d3130654 ("drm:
bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec") was correct
in this regard.
This patch basically reverts both commits. It was tested on an i.MX8M
SoC with an SN65DSI84 bridge. The signals were probed and the DSI
packets were decoded during initialization and link start-up. After this
patch the first DSI packet on the link is a VSYNC packet and the timing
is correct.
Command mode between .pre_enable and .enable was also briefly tested by
a quick hack. There was no DSI link partner which would have responded,
but it was made sure the DSI packet was send on the link. As a side
note, the command mode seems to just work in HS mode. I couldn't find
that the bridge will handle commands in LP mode.
Fixes: 20c827683de0 ("drm: bridge: samsung-dsim: Fix init during host transfer")
Fixes: 0c14d3130654 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113164344.1612602-1-mwalle@kernel.org
|
|
Change the timer layout in the dtb to fit the format that needed by
the SBI.
Fixes: 967a94a92aaa ("riscv: dts: add initial Sophgo SG2042 SoC device tree")
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Lantiq uses a common kernel config for devices with 24Kc and 34Kc cores.
The changes made previously to add support for interrupts on all cores
work on 24Kc platforms with SMP disabled and 34Kc platforms with SMP
enabled. This patch fixes boot issues on Danube (single core 24Kc) with
SMP enabled.
Fixes: 730320fd770d ("MIPS: lantiq: enable all hardware interrupts on second VPE")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Commit 61167ad5fecd("mm: pass nid to reserve_bootmem_region()") reveals
that reserved memblock regions have no valid node id set, just set it
right since loongson64 firmware makes it clear in memory layout info.
This works around booting failure on 3A1000+ since commit 61167ad5fecd
("mm: pass nid to reserve_bootmem_region()") under
CONFIG_DEFERRED_STRUCT_PAGE_INIT.
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
"cpu_probe" is called both by BP and APs, but reserving exception vector
(like 0x0-0x1000) called by "cpu_probe" need once and calling on APs is
too late since memblock is unavailable at that time.
So, reserve exception vector ONLY by BP.
Suggested-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Most of the symbols for which we do not have a prototype can actually be
made static and for the few that cannot, there is already a declaration
in a header for it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The addition of commit efa7df3e3bb5 ("mm: align larger anonymous mappings
on THP boundaries") caused the "virtual_address_range" mm selftest to
start failing on arm64. Let's fix that regression.
There were 2 visible problems when running the test; 1) it takes much
longer to execute, and 2) the test fails. Both are related:
The (first part of the) test allocates as many 1GB anonymous blocks as it
can in the low 256TB of address space, passing NULL as the addr hint to
mmap. Before the faulty patch, all allocations were abutted and contained
in a single, merged VMA. However, after this patch, each allocation is in
its own VMA, and there is a 2M gap between each VMA. This causes the 2
problems in the test: 1) mmap becomes MUCH slower because there are so
many VMAs to check to find a new 1G gap. 2) mmap fails once it hits the
VMA limit (/proc/sys/vm/max_map_count). Hitting this limit then causes a
subsequent calloc() to fail, which causes the test to fail.
The problem is that arm64 (unlike x86) selects
ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT. But __thp_get_unmapped_area()
allocates len+2M then always aligns to the bottom of the discovered gap.
That causes the 2M hole.
Fix this by detecting cases where we can still achive the alignment goal
when moved to the top of the allocated area, if configured to prefer
top-down allocation.
While we are at it, fix thp_get_unmapped_area's use of pgoff, which should
always be zero for anonymous mappings. Prior to the faulty change, while
it was possible for user space to pass in pgoff!=0, the old
mm->get_unmapped_area() handler would not use it. thp_get_unmapped_area()
does use it, so let's explicitly zero it before calling the handler. This
should also be the correct behavior for arches that define their own
get_unmapped_area() handler.
Link: https://lkml.kernel.org/r/20240123171420.3970220-1-ryan.roberts@arm.com
Fixes: efa7df3e3bb5 ("mm: align larger anonymous mappings on THP boundaries")
Closes: https://lore.kernel.org/linux-mm/1e8f5ac7-54ce-433a-ae53-81522b2320e1@arm.com/
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The stubs for kvm_own/lsx()/kvm_own_lasx() when CONFIG_CPU_HAS_LSX or
CONFIG_CPU_HAS_LASX is not defined should have a return value since they
return an int, so add "return -EINVAL;" to the stubs.
Fixes the build error:
In file included from ../arch/loongarch/include/asm/kvm_csr.h:12,
from ../arch/loongarch/kvm/interrupt.c:8:
../arch/loongarch/include/asm/kvm_vcpu.h: In function 'kvm_own_lasx':
../arch/loongarch/include/asm/kvm_vcpu.h:73:39: error: no return statement in function returning non-void [-Werror=return-type]
73 | static inline int kvm_own_lasx(struct kvm_vcpu *vcpu) { }
Fixes: db1ecca22edf ("LoongArch: KVM: Add LSX (128bit SIMD) support")
Fixes: 118e10cd893d ("LoongArch: KVM: Add LASX (256bit SIMD) support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Commit 8569992d64b8f750e34b7858eac ("KVM: Use gfn instead of hva for
mmu_notifier_retry") replaces mmu_invalidate_retry_hva() usage with
mmu_invalidate_retry_gfn() for X86, LoongArch also need similar changes
to fix build.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Machines which have more than 8 nodes fail to boot SMP after commit
a2ccf46333d7b2cf96 ("LoongArch/smp: Call rcutree_report_cpu_starting()
earlier"). Because such machines use tlb-based per-cpu base address
rather than dmw-based per-cpu base address, resulting per-cpu variables
can only be accessed after tlb_init(). But rcutree_report_cpu_starting()
is now called before tlb_init() and accesses per-cpu variables indeed.
Since the original patch want to avoid the lockdep warning caused by
page allocation in tlb_init(), we can move rcutree_report_cpu_starting()
to tlb_init() where after tlb exception configuration but before page
allocation.
Fixes: a2ccf46333d7b2cf96 ("LoongArch/smp: Call rcutree_report_cpu_starting() earlier")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
commit efa7df3e3bb5 ("mm: align larger anonymous mappings on THP
boundaries") caused two issues [1] [2] reported on 32 bit system or compat
userspace.
It doesn't make too much sense to force huge page alignment on 32 bit
system due to the constrained virtual address space.
[1] https://lore.kernel.org/linux-mm/d0a136a0-4a31-46bc-adf4-2db109a61672@kernel.org/
[2] https://lore.kernel.org/linux-mm/CAJuCfpHXLdQy1a2B6xN2d7quTYwg2OoZseYPZTRpU0eHHKD-sQ@mail.gmail.com/
Link: https://lkml.kernel.org/r/20240118180505.2914778-1-shy828301@gmail.com
Fixes: efa7df3e3bb5 ("mm: align larger anonymous mappings on THP boundaries")
Signed-off-by: Yang Shi <yang@os.amperecomputing.com>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Reported-by: Suren Baghdasaryan <surenb@google.com>
Tested-by: Jiri Slaby <jirislaby@kernel.org>
Tested-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Christopher Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
In mfill_atomic_hugetlb(), mmap_changing isn't being checked
again if we drop mmap_lock and reacquire it. When the lock is not held,
mmap_changing could have been incremented. This is also inconsistent
with the behavior in mfill_atomic().
Link: https://lkml.kernel.org/r/20240117223729.1444522-1-lokeshgidra@google.com
Fixes: df2cc96e77011 ("userfaultfd: prevent non-cooperative events vs mcopy_atomic races")
Signed-off-by: Lokesh Gidra <lokeshgidra@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Kalesh Singh <kaleshsingh@google.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Nicolas Geoffray <ngeoffray@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
ksm_tests was previously mmapping a region of memory, aligning the
returned pointer to a PMD boundary, then setting MADV_HUGEPAGE, but was
setting it past the end of the mmapped area due to not taking the pointer
alignment into consideration. Fix this behaviour.
Up until commit efa7df3e3bb5 ("mm: align larger anonymous mappings on THP
boundaries"), this buggy behavior was (usually) masked because the
alignment difference was always less than PMD-size. But since the
mentioned commit, `ksm_tests -H -s 100` started failing.
Link: https://lkml.kernel.org/r/20240122120554.3108022-1-ryan.roberts@arm.com
Fixes: 325254899684 ("selftests: vm: add KSM huge pages merging time test")
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Pedro Demarchi Gomes <pedrodemargomes@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The shadow call stack implementation fails to build without CONFIG_MMU:
ld.lld: error: undefined symbol: vfree_atomic
>>> referenced by scs.c
>>> kernel/scs.o:(scs_free) in archive vmlinux.a
Link: https://lkml.kernel.org/r/20240122175204.2371009-1-samuel.holland@sifive.com
Fixes: a2abe7cbd8fe ("scs: switch to vmapped shadow stacks")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The correct folio replacement for "set_page_dirty()" is
"folio_mark_dirty()", not "folio_set_dirty()". Using the latter won't
properly inform the FS using the dirty_folio() callback.
This has been found by code inspection, but likely this can result in some
real trouble when zapping dirty PTEs that point at clean pagecache folios.
Yuezhang Mo said: "Without this fix, testing the latest exfat with
xfstests, test cases generic/029 and generic/030 will fail."
Link: https://lkml.kernel.org/r/20240122171751.272074-1-david@redhat.com
Fixes: c46265030b0f ("mm/memory: page_remove_rmap() -> folio_remove_rmap_pte()")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Ryan Roberts <ryan.roberts@arm.com>
Closes: https://lkml.kernel.org/r/2445cedb-61fb-422c-8bfb-caf0a2beed62@arm.com
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The correct folio replacement for "set_page_dirty()" is
"folio_mark_dirty()", not "folio_set_dirty()". Using the latter won't
properly inform the FS using the dirty_folio() callback.
This has been found by code inspection, but likely this can result in some
real trouble.
Link: https://lkml.kernel.org/r/20240122175407.307992-1-david@redhat.com
Fixes: a8e61d584eda0 ("mm/huge_memory: page_remove_rmap() -> folio_remove_rmap_pmd()")
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
In order for the page table level 5 to be in use, the CPU must have the
setting enabled in addition to the CONFIG option. Check for the flag to be
set to avoid false test failures on systems that do not have this cpu flag
set.
The test does a series of mmap calls including three using the
MAP_FIXED flag and specifying an address that is 1<<47 or 1<<48. These
addresses are only available if you are using level 5 page tables,
which requires both the CPU to have the capabiltiy (la57 flag) and the
kernel to be configured. Currently the test only checks for the kernel
configuration option, so this test can still report a false positive.
Here are the three failing lines:
$ ./va_high_addr_switch | grep FAILED
mmap(ADDR_SWITCH_HINT, 2 * PAGE_SIZE, MAP_FIXED): 0xffffffffffffffff - FAILED
mmap(HIGH_ADDR, MAP_FIXED): 0xffffffffffffffff - FAILED
mmap(ADDR_SWITCH_HINT, 2 * PAGE_SIZE, MAP_FIXED): 0xffffffffffffffff - FAILED
I thought (for about a second) refactoring the test so that these three
mmap calls will only be run on systems with the level 5 page tables
available, but the whole point of the test is to check the level 5
feature...
Link: https://lkml.kernel.org/r/20240119205801.62769-1-audra@redhat.com
Fixes: 4f2930c6718a ("selftests/vm: only run 128TBswitch with 5-level paging")
Signed-off-by: Audra Mitchell <audra@redhat.com>
Cc: Rafael Aquini <raquini@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Adam Sindelar <adam@wowsignal.io>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
On systems with 64k page size and 512M huge page sizes, the allocation and
test succeeds but errors out at the munmap. As the comment states, munmap
will failure if its not HUGEPAGE aligned. This is due to the length of
the mapping being 1/2 the size of the hugepage causing the munmap to not
be hugepage aligned. Fix this by making the mapping length the full
hugepage if the hugepage is larger than the length of the mapping.
Link: https://lkml.kernel.org/r/20240119131429.172448-1-npache@redhat.com
Signed-off-by: Nico Pache <npache@redhat.com>
Cc: Donet Tom <donettom@linux.vnet.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
As discussed on the mailing list [1], merge the zpool maintainers entry
into the zswap one. Also, add CREDITS entries for previous zswap/zpool
maintainers.
[1] https://lore.kernel.org/linux-mm/CAJD7tkYx4YWhGoVwnSeGc8dY_1aRRxxg8PzWBV==A6iqG_OgFw@mail.gmail.com/
Link: https://lkml.kernel.org/r/20240117182152.1439822-1-yosryahmed@google.com
Signed-off-by: Yosry Ahmed <yosryahmed@google.com>
Acked-by: Nhat Pham <nphamcs@gmail.com>
Acked-by: Dan Streetman <ddstreet@ieee.org>
Acked-by: Seth Jennings <sjenning@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
With the introduction of the pool_rwlock (reader-writer lock), several
fast paths end up taking the pool_rwlock as readers. Furthermore,
stack_depot_put() unconditionally takes the pool_rwlock as a writer.
Despite allowing readers to make forward-progress concurrently,
reader-writer locks have inherent cache contention issues, which does not
scale well on systems with large CPU counts.
Rework the synchronization story of stack depot to again avoid taking any
locks in the fast paths. This is done by relying on RCU-protected list
traversal, and the NMI-safe subset of RCU to delay reuse of freed stack
records. See code comments for more details.
Along with the performance issues, this also fixes incorrect nesting of
rwlock within a raw_spinlock, given that stack depot should still be
usable from anywhere:
| [ BUG: Invalid wait context ]
| -----------------------------
| swapper/0/1 is trying to lock:
| ffffffff89869be8 (pool_rwlock){..--}-{3:3}, at: stack_depot_save_flags
| other info that might help us debug this:
| context-{5:5}
| 2 locks held by swapper/0/1:
| #0: ffffffff89632440 (rcu_read_lock){....}-{1:3}, at: __queue_work
| #1: ffff888100092018 (&pool->lock){-.-.}-{2:2}, at: __queue_work <-- raw_spin_lock
Stack depot usage stats are similar to the previous version after a KASAN
kernel boot:
$ cat /sys/kernel/debug/stackdepot/stats
pools: 838
allocations: 29865
frees: 6604
in_use: 23261
freelist_size: 1879
The number of pools is the same as previously. The freelist size is
minimally larger, but this may also be due to variance across system
boots. This shows that even though we do not eagerly wait for the next
RCU grace period (such as with synchronize_rcu() or call_rcu()) after
freeing a stack record - requiring depot_pop_free() to "poll" if an entry
may be used - new allocations are very likely to happen in later RCU grace
periods.
Link: https://lkml.kernel.org/r/20240118110216.2539519-2-elver@google.com
Fixes: 108be8def46e ("lib/stackdepot: allow users to evict stack traces")
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add a few basic stats counters for stack depot that can be used to derive
if stack depot is working as intended. This is a snapshot of the new
stats after booting a system with a KASAN-enabled kernel:
$ cat /sys/kernel/debug/stackdepot/stats
pools: 838
allocations: 29861
frees: 6561
in_use: 23300
freelist_size: 1840
Generally, "pools" should be well below the max; once the system is
booted, "in_use" should remain relatively steady.
Link: https://lkml.kernel.org/r/20240118110216.2539519-1-elver@google.com
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Alexander Potapenko <glider@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Alexander Potapenko writes in [1]: "For every memory access in the code
instrumented by KMSAN we call kmsan_get_metadata() to obtain the metadata
for the memory being accessed. For virtual memory the metadata pointers
are stored in the corresponding `struct page`, therefore we need to call
virt_to_page() to get them.
According to the comment in arch/x86/include/asm/page.h,
virt_to_page(kaddr) returns a valid pointer iff virt_addr_valid(kaddr) is
true, so KMSAN needs to call virt_addr_valid() as well.
To avoid recursion, kmsan_get_metadata() must not call instrumented code,
therefore ./arch/x86/include/asm/kmsan.h forks parts of
arch/x86/mm/physaddr.c to check whether a virtual address is valid or not.
But the introduction of rcu_read_lock() to pfn_valid() added instrumented
RCU API calls to virt_to_page_or_null(), which is called by
kmsan_get_metadata(), so there is an infinite recursion now. I do not
think it is correct to stop that recursion by doing
kmsan_enter_runtime()/kmsan_exit_runtime() in kmsan_get_metadata(): that
would prevent instrumented functions called from within the runtime from
tracking the shadow values, which might introduce false positives."
Fix the issue by switching pfn_valid() to the _sched() variant of
rcu_read_lock/unlock(), which does not require calling into RCU. Given
the critical section in pfn_valid() is very small, this is a reasonable
trade-off (with preemptible RCU).
KMSAN further needs to be careful to suppress calls into the scheduler,
which would be another source of recursion. This can be done by wrapping
the call to pfn_valid() into preempt_disable/enable_no_resched(). The
downside is that this sacrifices breaking scheduling guarantees; however,
a kernel compiled with KMSAN has already given up any performance
guarantees due to being heavily instrumented.
Note, KMSAN code already disables tracing via Makefile, and since mmzone.h
is included, it is not necessary to use the notrace variant, which is
generally preferred in all other cases.
Link: https://lkml.kernel.org/r/20240115184430.2710652-1-glider@google.com [1]
Link: https://lkml.kernel.org/r/20240118110022.2538350-1-elver@google.com
Fixes: 5ec8e8ea8b77 ("mm/sparsemem: fix race in accessing memory_section->usage")
Signed-off-by: Marco Elver <elver@google.com>
Reported-by: Alexander Potapenko <glider@google.com>
Reported-by: syzbot+93a9e8a3dea8d6085e12@syzkaller.appspotmail.com
Reviewed-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Cc: Charan Teja Kalla <quic_charante@quicinc.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
(struct dirty_throttle_control *)->thresh is an unsigned long, but is
passed as the u32 divisor argument to div_u64(). On architectures where
unsigned long is 64 bytes, the argument will be implicitly truncated.
Use div64_u64() instead of div_u64() so that the value used in the "is
this a safe division" check is the same as the divisor.
Also, remove redundant cast of the numerator to u64, as that should happen
implicitly.
This would be difficult to exploit in memcg domain, given the ratio-based
arithmetic domain_drity_limits() uses, but is much easier in global
writeback domain with a BDI_CAP_STRICTLIMIT-backing device, using e.g.
vm.dirty_bytes=(1<<32)*PAGE_SIZE so that dtc->thresh == (1<<32)
Link: https://lkml.kernel.org/r/20240118181954.1415197-1-zokeefe@google.com
Fixes: f6789593d5ce ("mm/page-writeback.c: fix divide by zero in bdi_dirty_limits()")
Signed-off-by: Zach O'Keefe <zokeefe@google.com>
Cc: Maxim Patlasov <MPatlasov@parallels.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Running charge_reserved_hugetlb.sh generates errors if sh is set to
dash:
./charge_reserved_hugetlb.sh: 9: [[: not found
./charge_reserved_hugetlb.sh: 19: [[: not found
./charge_reserved_hugetlb.sh: 27: [[: not found
./charge_reserved_hugetlb.sh: 37: [[: not found
./charge_reserved_hugetlb.sh: 45: Syntax error: "(" unexpected
Switch to using /bin/bash instead of /bin/sh. Make the switch for
write_hugetlb_memory.sh as well which is called from
charge_reserved_hugetlb.sh.
Link: https://lkml.kernel.org/r/20240116090455.3407378-1-usama.anjum@collabora.com
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The maintainer uses both.
Link: https://lkml.kernel.org/r/20240117122257.2707637-1-pvorel@suse.cz
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Reviewed-by: Alejandro Colomar <alx@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
While investigating hosts with high cgroup memory pressures, Tejun
found culprit zombie tasks that had were holding on to a lot of
memory, had SIGKILL pending, but were stuck in memory.high reclaim.
In the past, we used to always force-charge allocations from tasks
that were exiting in order to accelerate them dying and freeing up
their rss. This changed for memory.max in a4ebf1b6ca1e ("memcg:
prohibit unconditional exceeding the limit of dying tasks"); it noted
that this can cause (userspace inducable) containment failures, so it
added a mandatory reclaim and OOM kill cycle before forcing charges.
At the time, memory.high enforcement was handled in the userspace
return path, which isn't reached by dying tasks, and so memory.high
was still never enforced by dying tasks.
When c9afe31ec443 ("memcg: synchronously enforce memory.high for large
overcharges") added synchronous reclaim for memory.high, it added
unconditional memory.high enforcement for dying tasks as well. The
callstack shows that this path is where the zombie is stuck in.
We need to accelerate dying tasks getting past memory.high, but we
cannot do it quite the same way as we do for memory.max: memory.max is
enforced strictly, and tasks aren't allowed to move past it without
FIRST reclaiming and OOM killing if necessary. This ensures very small
levels of excess. With memory.high, though, enforcement happens lazily
after the charge, and OOM killing is never triggered. A lot of
concurrent threads could have pushed, or could actively be pushing,
the cgroup into excess. The dying task will enter reclaim on every
allocation attempt, with little hope of restoring balance.
To fix this, skip synchronous memory.high enforcement on dying tasks
altogether again. Update memory.high path documentation while at it.
[hannes@cmpxchg.org: also handle tasks are being killed during the reclaim]
Link: https://lkml.kernel.org/r/20240111192807.GA424308@cmpxchg.org
Link: https://lkml.kernel.org/r/20240111132902.389862-1-hannes@cmpxchg.org
Fixes: c9afe31ec443 ("memcg: synchronously enforce memory.high for large overcharges")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Yosry Ahmed <yosryahmed@google.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Dan Schatzberg <schatzberg.dan@gmail.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Muchun Song <muchun.song@linux.dev>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
commit efa7df3e3bb5 ("mm: align larger anonymous mappings on THP
boundaries") incured regression for stress-ng pthread benchmark [1]. It
is because THP get allocated to pthread's stack area much more possible
than before. Pthread's stack area is allocated by mmap without
VM_GROWSDOWN or VM_GROWSUP flag, so kernel can't tell whether it is a
stack area or not.
The MAP_STACK flag is used to mark the stack area, but it is a no-op on
Linux. Mapping MAP_STACK to VM_NOHUGEPAGE to prevent from allocating THP
for such stack area.
With this change the stack area looks like:
fffd18e10000-fffd19610000 rw-p 00000000 00:00 0
Size: 8192 kB
KernelPageSize: 4 kB
MMUPageSize: 4 kB
Rss: 12 kB
Pss: 12 kB
Pss_Dirty: 12 kB
Shared_Clean: 0 kB
Shared_Dirty: 0 kB
Private_Clean: 0 kB
Private_Dirty: 12 kB
Referenced: 12 kB
Anonymous: 12 kB
KSM: 0 kB
LazyFree: 0 kB
AnonHugePages: 0 kB
ShmemPmdMapped: 0 kB
FilePmdMapped: 0 kB
Shared_Hugetlb: 0 kB
Private_Hugetlb: 0 kB
Swap: 0 kB
SwapPss: 0 kB
Locked: 0 kB
THPeligible: 0
VmFlags: rd wr mr mw me ac nh
The "nh" flag is set.
[1] https://lore.kernel.org/linux-mm/202312192310.56367035-oliver.sang@intel.com/
Link: https://lkml.kernel.org/r/20231221065943.2803551-2-shy828301@gmail.com
Fixes: efa7df3e3bb5 ("mm: align larger anonymous mappings on THP boundaries")
Signed-off-by: Yang Shi <yang@os.amperecomputing.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Oliver Sang <oliver.sang@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Christopher Lameter <cl@linux.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: <stable@vger.kerenl.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
uprobes passes an unaligned page mapping address to
folio_add_new_anon_rmap(), which ends up triggering a VM_BUG_ON() we
recently extended in commit 372cbd4d5a066 ("mm: non-pmd-mappable, large
folios for folio_add_new_anon_rmap()").
Arguably, this is uprobes code doing something wrong; however, for the
time being it would have likely worked in rmap code because
__folio_set_anon() would set folio->index to the same value.
Looking at __replace_page(), we'd also pass slightly wrong values to
mmu_notifier_range_init(), page_vma_mapped_walk(), flush_cache_page(),
ptep_clear_flush() and set_pte_at_notify(). I suspect most of them are
fine, but let's just mark the introducing commit as the one needed fixing.
I don't think CC stable is warranted.
We'll add more sanity checks in rmap code separately, to make sure that we
always get properly aligned addresses.
Link: https://lkml.kernel.org/r/20240115100731.91007-1-david@redhat.com
Fixes: c517ee744b96 ("uprobes: __replace_page() should not use page_address_in_vma()")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Jiri Olsa <jolsa@kernel.org>
Closes: https://lkml.kernel.org/r/ZaMR2EWN-HvlCfUl@krava
Tested-by: Jiri Olsa <jolsa@kernel.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Use 2 separate variables of types int and unsigned long long instead of
confusing them. This corrects the correct print format for each of them
and removes the build warning:
warning: format `%d' expects argument of type `int', but argument 2 has type `long long unsigned int'
Link: https://lkml.kernel.org/r/20240112071851.612930-1-usama.anjum@collabora.com
Fixes: a4cb3b243343 ("selftests: mm: add a test for remapping to area immediately after existing mapping")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
has_extra_refcount() makes the assumption that the page cache adds a ref
count of 1 and subtracts this in the extra_pins case. Commit a08c7193e4f1
(mm/filemap: remove hugetlb special casing in filemap.c) modifies
__filemap_add_folio() by calling folio_ref_add(folio, nr); for all cases
(including hugtetlb) where nr is the number of pages in the folio. We
should adjust the number of references coming from the page cache by
subtracing the number of pages rather than 1.
In hugetlbfs_read_iter(), folio_test_has_hwpoisoned() is testing the wrong
flag as, in the hugetlb case, memory-failure code calls
folio_test_set_hwpoison() to indicate poison. folio_test_hwpoison() is
the correct function to test for that flag.
After these fixes, the hugetlb hwpoison read selftest passes all cases.
Link: https://lkml.kernel.org/r/20240112180840.367006-1-sidhartha.kumar@oracle.com
Fixes: a08c7193e4f1 ("mm/filemap: remove hugetlb special casing in filemap.c")
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Closes: https://lore.kernel.org/linux-mm/20230713001833.3778937-1-jiaqiyan@google.com/T/#m8e1469119e5b831bbd05d495f96b842e4a1c5519
Reported-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Acked-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: Muchun Song <muchun.song@linux.dev>
Cc: James Houghton <jthoughton@google.com>
Cc: Jiaqi Yan <jiaqiyan@google.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: <stable@vger.kernel.org> [6.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
ra_alloc_folio() marks a page that should trigger next round of async
readahead. However it rounds up computed index to the order of page being
allocated. This can however lead to multiple consecutive pages being
marked with readahead flag. Consider situation with index == 1, mark ==
1, order == 0. We insert order 0 page at index 1 and mark it. Then we
bump order to 1, index to 2, mark (still == 1) is rounded up to 2 so page
at index 2 is marked as well. Then we bump order to 2, index is
incremented to 4, mark gets rounded to 4 so page at index 4 is marked as
well. The fact that multiple pages get marked within a single readahead
window confuses the readahead logic and results in readahead window being
trimmed back to 1. This situation is triggered in particular when maximum
readahead window size is not a power of two (in the observed case it was
768 KB) and as a result sequential read throughput suffers.
Fix the problem by rounding 'mark' down instead of up. Because the index
is naturally aligned to 'order', we are guaranteed 'rounded mark' == index
iff 'mark' is within the page we are allocating at 'index' and thus
exactly one page is marked with readahead flag as required by the
readahead code and sequential read performance is restored.
This effectively reverts part of commit b9ff43dd2743 ("mm/readahead: Fix
readahead with large folios"). The commit changed the rounding with the
rationale:
"... we were setting the readahead flag on the folio which contains the
last byte read from the block. This is wrong because we will trigger
readahead at the end of the read without waiting to see if a subsequent
read is going to use the pages we just read."
Although this is true, the fact is this was always the case with read
sizes not aligned to folio boundaries and large folios in the page cache
just make the situation more obvious (and frequent). Also for sequential
read workloads it is better to trigger the readahead earlier rather than
later. It is true that the difference in the rounding and thus earlier
triggering of the readahead can result in reading more for semi-random
workloads. However workloads really suffering from this seem to be rare.
In particular I have verified that the workload described in commit
b9ff43dd2743 ("mm/readahead: Fix readahead with large folios") of reading
random 100k blocks from a file like:
[reader]
bs=100k
rw=randread
numjobs=1
size=64g
runtime=60s
is not impacted by the rounding change and achieves ~70MB/s in both cases.
[jack@suse.cz: fix one more place where mark rounding was done as well]
Link: https://lkml.kernel.org/r/20240123153254.5206-1-jack@suse.cz
Link: https://lkml.kernel.org/r/20240104085839.21029-1-jack@suse.cz
Fixes: b9ff43dd2743 ("mm/readahead: Fix readahead with large folios")
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Guo Xuenan <guoxuenan@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
All entities must be drained in the DRM scheduler run job worker to
avoid the following case. An entity found that is ready, no job found
ready on entity, and run job worker goes idle with other entities + jobs
ready. Draining all ready entities (i.e. loop over all ready entities)
in the run job worker ensures all job that are ready will be scheduled.
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Closes: https://lore.kernel.org/all/CABXGCsM2VLs489CH-vF-1539-s3in37=bwuOWtoeeE+q26zE+Q@mail.gmail.com/
Reported-and-tested-by: Mario Limonciello <mario.limonciello@amd.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3124
Link: https://lore.kernel.org/all/20240123021155.2775-1-mario.limonciello@amd.com/
Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Closes: https://lore.kernel.org/dri-devel/05ddb2da-b182-4791-8ef7-82179fd159a8@amd.com/T/#m0c31d4d1b9ae9995bb880974c4f1dbaddc33a48a
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240124210811.1639040-1-matthew.brost@intel.com
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.8-2024-01-25:
amdgpu:
- AC/DC power supply tracking fix
- Don't show invalid vram vendor data
- SMU 13.0.x fixes
- GART fix for umr on systems without VRAM
- GFX 10/11 UNORD_DISPATCH fixes
- IPS display fixes (required for S0ix on some platforms)
- Misc fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240125221503.5019-1-alexander.deucher@amd.com
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- Make an ops struct static
- Fix an implicit 0 to NULL conversion
- A couple of 32-bit fixes
- A migration coherency fix for Lunar Lake.
- An error path vm id leak fix
- Remove PVC references in kunit tests
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZbIb7l0EhpVp5cXE@fedora
|
|
Add a new helper, bch2_hash_lookup_in_snapshot(), for when we're not
operating in a subvolume and already have a snapshot ID, and then use it
in lookup_lostfound() -> __lookup_dirent().
This is a bugfix - lookup_lostfound() doesn't take a subvolume ID, we
were passing a nonsense subvolume ID before, and don't have one to pass
since we may be operating in an interior snapshot node that doesn't have
a subvolume ID.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/song/md into block-6.8
Pull MD fix from Song:
"This change fixes a RCU warning."
* tag 'md-6.8-20240126' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
md: fix a suspicious RCU usage warning
|
|
In __spi_pump_transfer_message(), the message was not finalized in the
first error return as it is in the other error return paths. Not
finalizing the message could cause anything waiting on the message to
complete to hang forever.
This adds the missing call to spi_finalize_current_message().
Fixes: ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240125205312.3458541-2-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
[Why]
IPS was temporary disabled due to instability.
It was fixed in dmub firmware and with:
- "drm/amd/display: Add IPS checks before dcn register access"
- "drm/amd/display: Disable ips before dc interrupt setting"
[How]
Enable IPS by default.
Disable IPS if 0x800 bit set in amdgpu.dcdebugmask module params
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For debugging IPS-related issues, expose a new debug mask
that allows to disable IPS.
Usage:
amdgpu.dcdebugmask=0x800
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
While in IPS2 an access to dcn registers is not allowed.
If interrupt results in dc call, we should disable IPS.
[How]
Safeguard register access in IPS2 by disabling idle optimization
before calling dc interrupt setting api.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Because ABM will wait VStart to start getting histogram data,
it will cause we can't enter IPS while full screnn video playing.
[How]
Modify the panel refresh rate to the maximun multiple of current
refresh rate.
Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
With IPS enabled a system hangs once PSR is active.
PSR active triggers transition to IPS2 state.
While in IPS2 an access to dcn registers results in hard hang.
Existing check doesn't cover for PSR sequence.
[How]
Safeguard register access by disabling idle optimization in atomic commit
and crtc scanout. It will be re-enabled on next vblank.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Introduce a new Replay mode for DMUB version 0.0.199.0
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Add regkey to block video playback in IPS2 by default
Allow idle optimizations in the same spot we allow Replay for
video playback usecases.
Avoid sending it when there's an external display connected by
modifying the allow idle checks to check for active non-eDP screens.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This needs to be set to 1 to avoid a potential deadlock in
the GC 10.x and newer. On GC 9.x and older, this needs
to be set to 0. This can lead to hangs in some mixed
graphics and compute workloads. Updated firmware is also
required for AQL.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This needs to be set to 1 to avoid a potential deadlock in
the GC 10.x and newer. On GC 9.x and older, this needs
to be set to 0. This can lead to hangs in some mixed
graphics and compute workloads. Updated firmware is also
required for AQL.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This allows kernel mapped pages like the PDB and PTB to be
read via the iomem debugfs when there is no vram in the system.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.7.x
|
|
Power limit of SMUv13.0.6 SOCs can be updated by out-of-band ways. Fetch
the limit from firmware instead of using cached values.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.7.x
|
|
amdgpu_reg_state_sysfs_fini could be invoked at the
time when asic_func is even not initialized, i.e.,
amdgpu_discovery_init fails for some reason.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
