| Age | Commit message (Collapse) | Author |
|---|
|
Convert the OMAP mux clock device tree binding to json-schema.
Specify the creator of the original binding as a maintainer.
Choose GPL-only license because original binding was also GPL.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241112162618.400194-1-andreas@kemnade.info
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Merge series from "Hendrik v. Raven" <h.v.raven@merzmedtech.de>:
This series adds support for the idle-state property from the mux
framework to the simple-mux audio variant. It allows to specify the state
of the mux when it is not in use.
|
|
Needed for new Intel board file changes.
|
|
simple-mux immediately activates the new output, even when it is powered
down. This can be undesirable in some cases, for example when a
mechanical relais is used.
Adds "idle-state" property from the mux controller to select the output
state to be used when the mux is powered down.
Signed-off-by: Hendrik v. Raven <h.v.raven@merzmedtech.de>
Link: https://patch.msgid.link/20241114-simple-mux-idle-state-v2-2-a30cb37d2be2@merzmedtech.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-mergewindow
at24 updates for v6.13-rc1
- add support for the lockable page on ST M24256E
|
|
LAN9646 switch is a 6-port switch with functions like KSZ9897. It has
4 internal PHYs and 1 SGMII port.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241109015705.82685-2-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.13
Most likely the last -next pull request for v6.13. Most changes are in
Realtek and Qualcomm drivers, otherwise not really anything
noteworthy.
Major changes:
mac80211
* EHT 1024 aggregation size for transmissions
ath12k
* switch to using wiphy_lock() and remove ar->conf_mutex
* firmware coredump collection support
* add debugfs support for a multitude of statistics
ath11k
* dt: document WCN6855 hardware inputs
ath9k
* remove include/linux/ath9k_platform.h
ath5k
* Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
rtw88:
* 8821au and 8812au USB adapters support
rtw89
* thermal protection
* firmware secure boot for WiFi 6 chip
* tag 'wireless-next-2024-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (154 commits)
Revert "wifi: iwlegacy: do not skip frames with bad FCS"
wifi: mac80211: pass MBSSID config by reference
wifi: mac80211: Support EHT 1024 aggregation size in TX
net: rfkill: gpio: Add check for clk_enable()
wifi: brcmfmac: Fix oops due to NULL pointer dereference in brcmf_sdiod_sglist_rw()
wifi: Switch back to struct platform_driver::remove()
wifi: ipw2x00: libipw_rx_any(): fix bad alignment
wifi: brcmfmac: release 'root' node in all execution paths
wifi: iwlwifi: mvm: don't call power_update_mac in fast suspend
wifi: iwlwifi: s/IWL_MVM_INVALID_STA/IWL_INVALID_STA
wifi: iwlwifi: bump minimum API version in BZ/SC to 92
wifi: iwlwifi: move IWL_LMAC_*_INDEX to fw/api/context.h
wifi: iwlwifi: be less noisy if the NIC is dead in S3
wifi: iwlwifi: mvm: tell iwlmei when we finished suspending
wifi: iwlwifi: allow fast resume on ax200
wifi: iwlwifi: mvm: support new initiator and responder command version
wifi: iwlwifi: mvm: use wiphy locked debugfs for low-latency
wifi: iwlwifi: mvm: MLO scan upon channel condition degradation
wifi: iwlwifi: mvm: support new versions of the wowlan APIs
wifi: iwlwifi: mvm: allow always calling iwl_mvm_get_bss_vif()
...
====================
Link: https://patch.msgid.link/20241113172918.A8A11C4CEC3@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip AT91 SoC updates for v6.13
It contains:
- DT bindings update for the SAM9X7 TCB block
* tag 'at91-soc-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
dt-bindings: microchip: atmel,at91rm9200-tcb: add sam9x7 compatible
Link: https://lore.kernel.org/r/20241113182050.2176500-3-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip AT91 device tree updates for v6.13
It contains:
- device tree support for the Microchip SAM9X7 SoC and the Microchip
SAM9X75 Curiosity board
- enable power monitor support for SAM9X60-EK, SAMA5D2-ICP,
SAMA7G45 Curiosity, SAMA7G5-EK boards
- updates the uart nodes with missing properties
- device tree cleanups
* tag 'at91-dt-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: microchip: sam9x75_curiosity: add sam9x75 curiosity board
dt-bindings: arm: add sam9x75 curiosity board
ARM: dts: at91: sam9x7: add device tree for SoC
ARM: dts: microchip: Rename LED sub nodes name
ARM: dts: microchip: Rename the pmic node
ARM: dts: microchip: Rename the eeprom nodename
ARM: dts: microchip: sama7g5ek: Add power monitor support
ARM: dts: microchip: sama7g54_curiosity: Add power monitor support
ARM: dts: microchip: sama5d2_icp: Add power monitor support
ARM: dts: microchip: sam9x60ek: Add power monitor support
ARM: dts: microchip: Unify rng node names
ARM: dts: microchip: Add trng labels for all at91 SoCs
ARM: dts: microchip: sam9x60: Add missing property atmel,usart-mode
Link: https://lore.kernel.org/r/20241113182050.2176500-2-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add devicetree bindings to support declaring optional voltage dividers to
the rail outputs of supported digital multiphase regulators. Some
applications require Vout to exceed the voltage range that the Vsense pin
can detect. This binding definition allows users to define the
characteristics of a voltage divider placed between Vout and the Vsense
pin for any rail powered by the device.
These bindings copy the vout-voltage-divider property defined in the
maxim,max20730 bindings schema since it is the best fit for the use case
of scaling hwmon PMBus telemetry. The generic voltage-divider property
used by many iio drivers was determined to be a poor fit because that
schema is tied directly to iio for the purpose of scaling io-channel
voltages and the isl68137 driver is not an iio driver.
New schema file named isil,isl68137.yaml to align with the corresponding
driver name and pre-existing bindings ported from trivial bindings.
However, all new device bindings use renesas as the vendor prefix
since Renesas acquired Intersil and now maintains all documentation
for the devices.
Signed-off-by: Grant Peltier <grantpeltier93@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Message-ID: <f7ac200e982961ff733de27a5c4505c04d68b6f3.1731439797.git.grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
Compatibles for some additional "General Register Files" syscons
* tag 'v6.13-armsoc/drivers1' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: soc: rockchip: add rk3588 mipi dcphy syscon
dt-bindings: soc: rockchip: add rk3576 usb2phy syscon
dt-bindings: soc: rockchip: add rk3576 vo1-grf syscon
Link: https://lore.kernel.org/r/4605658.LvFx2qVVIh@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
A few more Qualcomm driver updates for v6.13
Make the Adreno driver invoke the SMMU aperture setup firmware function,
which is required to allow the GPU to manage per-process page tables in
some firmware versions - as an example Rb3Gen2 has no GPU without this.
Add X1E Devkit to the list of devices that has functional EFI variable
access through the uefisecapp.
Flip the "manual slice configuration quirk" in the Qualcomm LLCC driver,
as this only applies to a single platform, and introduce support for
QCS8300, QCS615, SAR2130P, and SAR1130P.
Lastly, add IPQ5424 and IPQ5404 to the Qualcomm socinfo driver.
* tag 'qcom-drivers-for-6.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
soc: qcom: llcc: Add configuration data for QCS615
dt-bindings: cache: qcom,llcc: Document the QCS615 LLCC
soc: qcom: llcc: add support for SAR2130P and SAR1130P
soc: qcom: llcc: use deciman integers for bit shift values
dt-bindings: cache: qcom,llcc: document SAR2130P and SAR1130P
Link: https://lore.kernel.org/r/20241113032425.356306-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Document the compatible string for tsens v1.4 block found in MSM8937.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20241113-msm8917-v6-4-c348fb599fef@mainlining.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Document compatible for thermal sensors on Qualcomm SAR2130P platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241027-sar2130p-tsens-v1-1-8dee27fc02ae@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The UMS9632 uses the SC9632 serial device.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Link: https://lore.kernel.org/r/20241113110516.2166328-3-Wenhua.Lin@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PM8550VE has two more supplies (s1-8) than the PM8550VS (s1-6),
so move to a correct if:then: clause to accurately reflect that.
Fixes: 902f8c9830c3 ("regulator: dt-bindings: qcom,rpmh: Correct PM8550 family supplies")
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20241112003544.2807368-1-quic_molvera@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add documentation for the Qualcomm sm8750 tlmm.
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20241112002843.2804490-2-quic_molvera@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Convert the Actions Semi Owl timer bindings to DT schema.
Changes during conversion:
- Add a description
- Add "clocks" as a required property, since the driver searches for it
- Correct the given example according to owl-s500.dtsi
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241103123513.2890107-1-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The Goodix GT7986U touch controller report touch data according to the
HID protocol through the SPI bus. However, it is incompatible with
Microsoft's HID-over-SPI protocol.
NOTE: these bindings are distinct from the bindings used with the
GT7986U when the chip is running I2C firmware. For some background,
see discussion on the mailing lists in the thread:
https://lore.kernel.org/r/20241018020815.3098263-2-charles.goodix@gmail.com
Signed-off-by: Charles Wang <charles.goodix@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung SoC drivers for v6.13
Add Samsung ChipID driver support for new SoCs: Exynos8895, Exynos990
and Exynos9810.
* tag 'samsung-drivers-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: exynos-chipid: Add support for Exynos9810 SoC
dt-bindings: hwinfo: samsung,exynos-chipid: Add Samsung exynos9810 compatible
soc: samsung: exynos-chipid: Add support for Exynos 990 chipid
dt-bindings: hwinfo: exynos-chipid: Add compatible for Exynos 990 chipid
soc: samsung: exynos-chipid: add exynos8895 SoC support
dt-bindings: hwinfo: samsung,exynos-chipid: add exynos8895 compatible
Link: https://lore.kernel.org/r/20241029081002.21106-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Apple SoC DT updates for 6.13:
- Added base DTs for a bunch of non-Mac Apple iDevices (pre-M1)
* tag 'asahi-soc-dt-6.13' of https://github.com/AsahiLinux/linux:
arm64: Kconfig: Update help text for CONFIG_ARCH_APPLE
arm64: dts: apple: Add A11 devices
arm64: dts: apple: Add A10X devices
arm64: dts: apple: Add A10 devices
arm64: dts: apple: Add A9X devices
arm64: dts: apple: Add A9 devices
arm64: dts: apple: Add A8X devices
arm64: dts: apple: Add A8 devices
arm64: dts: apple: Add A7 devices
dt-bindings: arm: apple: Add A11 devices
dt-bindings: arm: apple: Add A10X devices
dt-bindings: arm: apple: Add A10 devices
dt-bindings: arm: apple: Add A9X devices
dt-bindings: arm: apple: Add A9 devices
dt-bindings: arm: apple: Add A8X devices
dt-bindings: arm: apple: Add A8 devices
dt-bindings: arm: apple: Add A7 devices
dt-bindings: pinctrl: apple,pinctrl: Add A7-A11 compatibles
dt-bindings: watchdog: apple,wdt: Add A7-A11 compatibles
dt-bindings: arm: cpus: Add Apple A7-A11 CPU cores
Link: https://lore.kernel.org/r/a8a19596-5d46-4562-9555-3b3ae7a5a3e5@marcan.st
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
More new boards: Rock-5C, Banana Pi P2 Pro
HDMI output enabled on a huge number of rk3588 boards, now that we
have the ability to do that.
A new RK356x variant - the RK3566T (with lower max-frequencies). The
variant was already in use on some boards which then encoded those OPP
differences in the board files itself. This moves this to saner place.
Fixed-regulator nowadays has a preferred node-naming scheme set in the
binding and we had accumulated a number of different styles over time.
A change brings all of them in line for arm64 dts files.
* tag 'v6.13-rockchip-dts64-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (24 commits)
arm64: dts: rockchip: use less broad pinctrl for pcie3x1 on Radxa E25
arm64: dts: rockchip: add Radxa ROCK 5C
dt-bindings: arm: rockchip: add Radxa ROCK 5C
arm64: dts: rockchip: orangepi-5-plus: Enable GPU
arm64: dts: rockchip: enable USB3 on NanoPC-T6
arm64: dts: rockchip: adapt regulator nodenames to preferred form
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi GenBook
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi 4B
arm64: dts: rockchip: Enable HDMI0 for rk3588 Cool Pi CM5 EVB
arm64: dts: rockchip: Enable HDMI on NanoPi R6C/R6S
arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S
arm64: dts: rockchip: Enable HDMI on Hardkernel ODROID-M2
arm64: dts: rockchip: Remove non-removable flag from sdmmc on rk3576-sige5
arm64: dts: rockchip: Enable HDMI0 on FriendlyElec CM3588 NAS
arm64: dts: rockchip: add Banana Pi P2 Pro board
dt-bindings: arm: rockchip: add Banana Pi P2 Pro board
arm64: dts: rockchip: Add new SoC dtsi for the RK3566T variant
arm64: dts: rockchip: Prepare RK356x SoC dtsi files for per-variant OPPs
arm64: dts: rockchip: Update CPU OPP voltages in RK356x SoC dtsi
arm64: dts: rockchip: Add OPP voltage ranges to RK3399 OP1 SoC dtsi
...
Link: https://lore.kernel.org/r/3313711.oiGErgHkdL@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
Fixed-regulator nowadays has preferred node-naming scheme set in the
binding. This gets all boards on the same state for Rockchip arm32-dts.
* tag 'v6.13-rockchip-dts32-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: adapt regulator nodenames to preferred form
ARM: dts: rockchip: Add Relfor Saib board
dt-bindings: arm: rockchip: Add Relfor Saib board
dt-bindings: vendor-prefixes: Add Relfor labs
ARM: dts: rockchip: Add watchdog node for RV1126
dt-bindings: watchdog: rockchip: Add rockchip,rv1126-wdt string
Link: https://lore.kernel.org/r/6740039.4vTCxPXJkl@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
Allwinner Device Tree changes for 6.13 part 2
- Remove accidental suniv duplicates in Makefile
- Add second source magnetometer for Pine Phone
- Add orientation (mount matrix) for Pine Phone's accelerometer and
magnetometer
- Enable eMMC and MMC on A100 Perf1
* tag 'sunxi-dt-for-6.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a100: perf1: Add eMMC and MMC node
arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
arm64: dts: sun50i-a64-pinephone: Add mount-matrix for PinePhone magnetometers
arm64: dts: sun50i-a64-pinephone: Add AF8133J to PinePhone
ARM: dts: allwinner: Remove accidental suniv duplicates
arm64: allwinner: a100: Add MMC related nodes
arm64: dts: allwinner: a100: add usb related nodes
dt-bindings: usb: sunxi-musb: Add A100 compatible string
dt-bindings: usb: Add A100 compatible string
dt-bindings: phy: sun50i-a64: add a100 compatible
arm64: dts: allwinner: a100: add watchdog node
arm64: dts: allwinner: A100: Add PMU mode
ARM: dts: sunxi: add support for RerVision A33-Vstar board
dt-bindings: arm: sunxi: document RerVision A33-Vstar board
arm64: dts: allwinner: Add disable-wp for boards with micro SD card
arm64: dts: allwinner: h313/h616/h618/h700: Enable audio codec for all supported boards
arm64: dts: allwinner: h616: Add audio codec node
Link: https://lore.kernel.org/r/ZzC-OF57MT_yCeWH@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.13
StarFive:
Support for the DeepComputing FML13V01, a Framework laptop compatible
with a JH7110. This board is fairly different to the more standard SBCs
offerings that the kernel already supports, so there's also some
refactoring of jh7110-common.dtsi to move out nodes unused on the new
board.
Spacemit:
A vendor prefix I grabbed from the basic support series, since its
dependencies are not yet ready but peripheral drivers have started being
merged.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: add DeepComputing FML13V01 board device tree
dt-bindings: riscv: starfive: add deepcomputing,fml13v01
dt-bindings: vendor: add deepcomputing
riscv: dts: starfive: jh7110-common: move usb0 config to board dts
riscv: dts: starfive: jh7110-common: revised device node
dt-bindings: vendor-prefixes: add spacemit
Link: https://lore.kernel.org/r/20241108-washboard-material-6b9ff196063d@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Delta AFC0612DB-F00 fan has to be set to at least 30% PWM duty cycle
to spin up from a stopped state, and can be afterward throttled down to
lower PWM duty cycle. Introduce support for operating such fans which
need to start at higher PWM duty cycle first and can slow down next.
Document two new DT properties, "fan-stop-to-start-percent" and
"fan-stop-to-start-usec". The former describes the minimum percent
of fan RPM at which it will surely spin up from stopped state. This
value can be found in the fan datasheet and can be converted to PWM
duty cycle easily. The "fan-stop-to-start-usec" describes the minimum
time in microseconds for which the fan has to be set to stopped state
start RPM for the fan to surely spin up.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Message-ID: <20241106185925.223736-1-marex@denx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The register layout of P3T1085 is the same as ti,tmp108. Add compatible
string nxp,p3t1085 for it. The difference of P3T1085 is support I3C.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Message-ID: <20241111-p3t1085-v3-1-bff511550aad@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add DT binding for the Texas Instruments TPS25990 eFuse
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Message-ID: <20241105-tps25990-v4-6-0e312ac70b62@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/dt
TI K3 device tree updates for v6.13
Generic Fixups/Cleanups:
- Cleanup bootph-* tags to limit to leaf nodes only
- clock IDs for MCSPI instances fixed up across J7xx family
- Misc indentation and whitespace cleanup across dts
New SoC
- J742s2 which is a cutdown of existing J784s4 and uses same EVM
SoC Specific features and Fixes:
- eQEP (counter) support across AM64/AM62/AM62A
AM64
- M4F Remoteproc support
- stats collection support for ICSSGs via ti,pa-stats
- Add PCIe EP overlays
AM65
- stats collection support for ICSSGs via ti,pa-stats
AM62:
- M4F Remoteproc support
- eMMC/SD TAP value updates
- dtbs_check fixes for opp_efuse_table
AM62A
- 1.4GHz opp entry
AM62P
- 1.4GHz opp entry
J7200
- Add PCIe EP overlays
- Pinmux node reg range fixes
Board Specific
AM62
- am62 verdin ivy carrier board support
- am625-verdin TPM device support
- am62 verdin ivy board support
- Beagleplay Mikrobus PWM header support
- am62-verdin increase SD regulator startup delay
AM64
- am642-phyboard-electra-rdk trickle charger support
- am64-phy* drop buswidth from sdhci nodes
* tag 'ti-k3-dt-for-v6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux: (61 commits)
arm64: dts: ti: k3-am62: use opp_efuse_table for opp-table syscon
arm64: dts: ti: k3-am62p5-sk: add 1.4ghz opp entry
arm64: dts: ti: k3-am62p: add opp frequencies
arm64: dts: ti: k3-am62a7-sk: add 1.4ghz opp entry
arm64: dts: ti: k3-am62a: add opp frequencies
arm64: dts: ti: k3-am62-verdin: Add Ivy carrier board
arm64: dts: ti: k3-am62-verdin: add label to som adc node
dt-bindings: arm: ti: Add verdin am62 ivy board
arm64: dts: ti: k3-am642-phyboard-electra-rdk: Enable trickle charger
arm64: dts: ti: k3-am64-phycore-som: Add M4F remoteproc nodes
arm64: dts: ti: k3-am62-phycore-som: Add M4F remoteproc nodes
arm64: dts: ti: minor whitespace cleanup
arm64: dts: ti: k3-am62x-phyboard-lyra: Fix indentation in audio-card
arm64: dts: ti: k3-am642-phyboard-electra-rdk: Fix bus-width property in MMC nodes
arm64: dts: ti: k3-am64-phycore-som: Fix bus-width property in MMC nodes
arm64: dts: ti: k3-am642-evm: Add overlay for PCIe0 EP mode
arm64: dts: ti: k3-j7200-evm: Add overlay for PCIE1 Endpoint Mode
arm64: dts: ti: k3-am62-main: Update otap/itap values
arm64: dts: ti: k3-am625-beagleplay: Enable MikroBUS PWM
arm64: dts: ti: k3-am62-verdin: Fix SD regulator startup delay
...
Link: https://lore.kernel.org/r/3ded4795-2186-4e06-bda6-9c9a65a3fdb9@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm64 DeviceTree changes for v6.13
Introduce descriptions of the 8cx Gen3-based Microsoft Surface Pro 9 5G,
X Elite based Dell XPS 13 9345, the QCS9100 platform and the "Ride"
development boards thereon, and the SM7325 platform and the Nothing
Phone 1.
MSM8998 gains support for HDMI. The Lenovo Miix 630 gains support for
volume keys, audio and sensor DSPs, touchscreen, and its specific WiFi
calibration variant.
On QCM6490, Fairphone FP5 gains a thermistor adjacent to UFS/RAM, while
the IDP gains UFS and WiFi support. For QCS6490 changes to Rb3Gen2
enables WiFi, Venus, PCIe, SD-card, and volume keys. Adreno speedbins
are adjusted and PMU nodes' compatibles for the two clusters are
corrected.
The DB845C/RB3 and QRB5165 RB5 vision mezzanines are converted to
DeviceTree overlays, and both gains CMA heap for libcamera to use.
SA8775P gains GPI DMA support, support for controlling download mode
(bootloader-assisted ramdump support), additional UARTs, and qcrypto
support. The "Ride" development board gains WiFi and Bluetooth support.
On SC8280XP (8cx Gen3) another UART is described, used in the
Microsoft Surface 9 5G. The WiFi/BT combo chip's power management unit
is described on the CRD and Lenovo ThinkPad X13s.
On SDM630/660 the GPU SMMU and clock controller is added, as is the
A2Noc and LPASS SMMU, and the DSP-based WiFi device. GPU, modem DSP and
WiFi is then enabled on the Inforce 6560 development board.
On SM8450 Hardware Development Kit, the WCN6855 is modelled to enable
WiFi and Bluetooth. A "global" interrupt is defined on SM8450 PCIe RC
controller, to enable hotplug.
On X Elite, USB Type-C controllers are marked as usb-role-switch
capable, the GICv3 ITS is enabled for PCIe. TCSR region is described and
wired up to allow setting and cleaning the download mode
(bootloader-assisted ramdump) flag, and residency numbers for C4/C5 are
updated.
USB role switch is enabled on Lenovo ThinkPad T14s and the ASUS Vivobook
S15. The T14s also gains support for a second source trackpad. The
Microsoft Surface Laptop gains LID switch and the USB Type-A connector
attached to the multiport controller is enabled. The CRD has its HID
device power supplies described.
Application SMMU is flagged as DMA coherent across QDU1000, SC7180,
SC8180X, SC8280XP, SDM670, SDM845, SM8150, SM8350, SM8450, and X1E80100.
In addition to this, the effort to improve style and binding compliance
continued.
* tag 'qcom-arm64-for-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (120 commits)
arm64: dts: qcom: sdm845-db845c-navigation-mezzanine: Add cma heap for libcamera softisp support
arm64: dts: qcom: qrb5165-rb5-vision-mezzanine: Add cma heap for libcamera softisp support
arm64: dts: qcom: qrb5165-rb5-vision-mezzanine: Drop redundant clock-lanes from camera@1a
arm64: dts: qcom: sc8280xp-x13s: Drop redundant clock-lanes from camera@10
arm64: dts: qcom: sdm845-db845c-navigation-mezzanine: Convert mezzanine riser to dtso
arm64: dts: qcom: qrb5165-rb5-vision-mezzanine: Convert mezzanine riser to dtbo
arm64: dts: qcom: sm8450-hdk: model the PMU of the on-board wcn6855
arm64: dts: qcom: sc8280xp-x13s: model the PMU of the on-board wcn6855
arm64: dts: qcom: sc8280xp-crd: enable bluetooth
arm64: dts: qcom: sc8280xp-crd: model the PMU of the on-board wcn6855
arm64: dts: qcom: qcs9100: Add support for the QCS9100 Ride and Ride Rev3 boards
dt-bindings: arm: qcom: Document qcs9100-ride and qcs9100-ride Rev3
arm64: dts: qcom: x1e80100: Update C4/C5 residency/exit numbers
arm64: dts: qcom: x1e80100-crd: describe HID supplies
arm64: dts: qcom: msm8998-lenovo-miix-630: add WiFi calibration variant
arm64: dts: qcom: msm8998-clamshell: enable resin/VolDown
arm64: dts: qcom: msm8998-lenovo-miix-630: enable VolumeUp button
arm64: dts: qcom: msm8998-lenovo-miix-630: enable aDSP and SLPI
arm64: dts: qcom: msm8998-lenovo-miix-630: enable touchscreen
arm64: dts: qcom: qcs6490-rb3gen2: Add PCIe nodes
...
Link: https://lore.kernel.org/r/20241105164901.7787-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.13 (take two)
- Add a CPU Operating Performance Points table for the RZ/V2H SoC,
- Add Battery Backup Function (VBATTB) and RTC support for the RZ/G3S
SoC and the RZ/G3S SMARC SoM,
- Add DMAC support for MMC on the RZ/A1H SoC and the Genmai
development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.13-tag2' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: rzg3s-smarc-som: Enable RTC
arm64: dts: renesas: rzg3s-smarc-som: Enable VBATTB
arm64: dts: renesas: r9a08g045: Add RTC node
arm64: dts: renesas: r9a08g045: Add VBATTB node
arm64: dts: renesas: white-hawk-cpu-common: Add pin control for DSI-eDP IRQ
ARM: dts: renesas: r7s72100: Add DMA support to MMCIF
ARM: dts: renesas: r7s72100: Add DMAC node
arm64: dts: renesas: hihope: Drop #sound-dai-cells
dt-bindings: clock: renesas,r9a08g045-vbattb: Document VBATTB
dt-bindings: clock: r9a08g045-cpg: Add power domain ID for RTC
arm64: dts: renesas: r9a09g057: Add OPP table
Link: https://lore.kernel.org/r/cover.1730726155.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/dt
MediaTek ARM64 DeviceTree updates for v6.13
MT8195 (also called MT8395)
- Enabled GPU support on Genio 1200 EVK
- Added sound-dai-cells for audio codec on MT8195 Cherry Chromebooks
MT8192:
- Added support Asurada Chromebook variants with Synaptics trackpad
MT8188 (also called MT8390):
- Added support for CPU DVFS, IOMMU, PWM hardware, SPMI bus,
Audio, socinfo, PCI-Express, DisplayPort, MIPI DSI, Ethernet,
Video HW Encoders (Stateful) and HW Decoders (Stateless),
JPEG HW Encoder/Decoder.
- Enabled GPU support on Genio 700 EVK
MT8183:
- Added support for Video HW Encoders (Stateful)
- Added HDMI support on MT8183 Pumpkin board
- Fixed some regulators to provide the actual description of the
power rails in MT8183 Kukui Chromebooks
- Disabled DPI display interface on MT8183 Kukui Chromebooks
to fix internal display probing
- Fixed address of EEPROM found on MT8183 Kakadu/Kodama Chromebooks
- Added SCL internal delay on I2C2 bus for improved I2C-HID devices
reliability on MT8183 Jacuzzi Chromebooks
MT7988:
- Added support for eFuses and UART controllers
Plus, addition of OF Graph support in MediaTek MMSYS and some cleanups
and dtbs_check fixes for MT8195 and for all machines using the MT6358
PMIC.
* tag 'mtk-dts64-for-v6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux: (55 commits)
arm64: dts: mediatek: mt8183-kukui: Drop bogus fixed regulators
arm64: dts: mediatek: mt8183-kukui-jacuzzi: Add supplies for fixed regulators
arm64: dts: mediatek: mt8183-kukui-jacuzzi: Fix DP bridge supply names
arm64: dts: mediatek: mt6358: fix dtbs_check error
arm64: dts: mediatek: mt8186-corsola: Fix IT6505 reset line polarity
arm64: dts: mt8183: Damu: add i2c2's i2c-scl-internal-delay-ns
arm64: dts: mt8183: cozmo: add i2c2's i2c-scl-internal-delay-ns
arm64: dts: mt8183: burnet: add i2c2's i2c-scl-internal-delay-ns
arm64: dts: mt8183: fennel: add i2c2's i2c-scl-internal-delay-ns
dt-bindings: arm: mediatek: mmsys: Add OF graph support for board path
arm64: dts: mediatek: mt8186-corsola: Fix GPU supply coupling max-spread
arm64: dts: mediatek: mt8195-cherry: Use correct audio codec DAI
arm64: dts: mediatek: mt8188: Fix USB3 PHY port default status
arm64: dts: mediatek: mt8173-elm-hana: Add vdd-supply to second source trackpad
arm64: dts: mediatek: mt8186-corsola-voltorb: Merge speaker codec nodes
arm64: dts: mediatek: mt8390-genio-700-evk: Enable ethernet
arm64: dts: mediatek: mt8188: Add ethernet node
arm64: dts: mediatek: mt8188: Add eDP and DP TX nodes
arm64: dts: mediatek: mt8188: Add DP-INTF nodes
arm64: dts: mediatek: mt8188: Add display nodes for vdosys1
...
Link: https://lore.kernel.org/r/20241104112625.161365-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX dt-bindings changes for 6.13:
- Add vendor prefix for ComVetia AG
- Add new board compatibles for Kobo Clara 2E, Boundary Device Nitrogen8MP,
Comvetia LXR, Kontron i.MX8MP OSM-S, Verdin i.MX8MM/P Ivy, DH Electronics
DHCOM, IOTA2 Lumpy, Gateworks GW82XX-2x
- A couple changes from Fabio Estevam to improve imx-anatop and imx-gpc
bindings
- A fsl,dsp bindings update from Laurentiu Mihalcea to correct power domain
count
* tag 'imx-bindings-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: add compatible strings for Kobo Clara 2E
dt-bindings: power: fsl,imx-gpc: Document fsl,imx6sll-gpc
dt-bindings: soc: imx: fsl,imx-anatop: Add additional regulators
dt-bindings: soc: imx: fsl,imx-anatop: Fix the i.MX7 irq number
dt-bindings: arm: fsl: Add Boundary Device Nitrogen8MP Universal SMARC Carrier Board
dt-bindings: arm: fsl: Add Gateworks GW82XX-2x dev kit
dt-bindings: dsp: fsl,dsp: fix power domain count
dt-bindings: arm: fsl: Document i.MX6DL DHCOM SoM on PDK2 carrier board
dt-bindings: arm: fsl: Document DH electronics i.MX8M Plus DHCOM PicoITX
dt-bindings: arm: fsl: Document DH i.MX8MP DHCOM SoM on DRC02 carrier board
dt-bindings: arm: Add i.MX8MP IOTA2 Lumpy board
dt-bindings: arm: freescale: Add verdin imx8mp ivy board
dt-bindings: arm: freescale: Add verdin imx8mm ivy board
dt-bindings: arm: fsl: Document the Comvetia LXR board
dt-bindings: vendor-prefixes: Add an entry for ComVetia AG
dt-bindings: arm: fsl: Add Kontron i.MX8MP OSM-S based boards
Link: https://lore.kernel.org/r/20241104090055.1881860-3-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
New SoCs: basic RK3528 support, RK3399S - a variant made specifically
for the Pinephone Pro and for consistencies sake it gets its own SoC
dtsi to not hide the specifics in the Pinephone Pro devicetree.
New boards: OrangePi-5b, NanoPi R3S, ArmSom Sige 5 (first rk3576 board),
Radxa e20c (first rk3528 board), Powkiddy RGB20SX, RK3588S-EVB1 and
the ArmSoM LM7 SoM with W3 carrier board.
HDMI support for rk3588 brings the first graphical output capability
there. This includes of course needed changes to a number of boards.
And finally a bunch of newly enabled peripherals on different boards,
as well as changes to adhere better to bindings and removal/change of
deprecated properties.
* tag 'v6.13-armsoc/dts64-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (64 commits)
arm64: dts: rockchip: Add rk3588-orangepi-5b device tree
dt-bindings: arm: rockchip: Add Orange Pi 5b enum to Orange Pi 5 entry
arm64: dts: rockchip: refactor common Orange Pi 5 board
arm64: dts: rockchip: Remove 'enable-active-low' from two boards
arm64: dts: rockchip: add HDMI support to rk3588-jaguar
arm64: dts: rockchip: add HDMI support to rk3588-tiger-haikou
arm64: dts: rockchip: add HDMI pinctrl to rk3588-tiger SoM
arm64: dts: rockchip: reorder mmc aliases for NanoPi R3S
arm64: dts: rockchip: enable eMMC HS200 mode for NanoPi R3S
arm64: dts: rockchip: sort props in pmu_io_domains node for NanoPi R3S
arm64: dts: rockchip: replace deprecated snps,reset props for NanoPi R3S
arm64: dts: rockchip: fix model name for FriendlyElec NanoPi R3S
arm64: dts: rockchip: Enable HDMI0 on rock-5a
arm64: dts: rockchip: Enable HDMI0 on rk3588-nanopc-t6
arm64: dts: rockchip: pwm-leds for Orange Pi 5
arm64: dts: rockchip: reorder audio/hdmi nodes in Orange Pi 5
arm64: dts: rockchip: analog audio on Orange Pi 5
arm64: dts: rockchip: Add dtsi file for RK3399S SoC variant
arm64: dts: rockchip: Convert dts files used as parents to dtsi files
arm64: dts: rockchip: fix the pcie refclock oscillator on Rock 5 ITX
...
Link: https://lore.kernel.org/r/12542111.O9o76ZdvQC@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM64 changes for v6.13
1. Add new SoC Samsung Exynos8895 and new board using it: Samsung
Galaxy S8 (SM-G950F) mobile phone. Only small support so far:
CPUs (Samsung Mongoose M2), main clock controllers (FSYS, PERIC,
TOP), pin controllers, SPI for cameras, timers.
2. Add new SoC Samsung Exynos990 and new board using it: Samsung
Galaxy Note20 5G (c1s/SM-N981B) mobile phone. Only minimal support
so far: CPUs (Samsung Mongoose M5), pin controllers, timers.
3. Prepare for adding new SoC Samsung Exynos9810 - add bindings. The
SoC DTSI was not yet ready, but it is posted on the mailing lists so
should come soon.
4. ExynosAutov920: Add several clock controllers.
* tag 'samsung-dt64-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: arm: samsung: Document Exynos9810 and starlte board binding
dt-bindings: soc: samsung: exynos-pmu: Add exynos9810 compatible
dt-bindings: arm: cpus: Add Samsung Mongoose M3
arm64: dts: exynos8895: Add spi_0/1 nodes
arm64: dts: exynos8895: Add Multi Core Timer (MCT) node
arm64: dts: exynos8895: Add clock management unit nodes
dt-bindings: timer: exynos4210-mct: Add samsung,exynos8895-mct compatible
dt-bindings: clock: samsung: Add Exynos8895 SoC
arm64: dts: exynos: Add initial support for Samsung Galaxy Note20 5G (c1s)
arm64: dts: exynos: Add initial support for the Exynos 990 SoC
dt-bindings: arm: samsung: samsung-boards: Add bindings for Exynos 990 boards
dt-bindings: arm: cpus: Add Samsung Mongoose M5
arm64: dts: exynosautov920: add peric1, misc and hsi0/1 clock DT nodes
dt-bindings: clock: exynosautov920: add peric1, misc and hsi0/1 clock definitions
arm64: dts: exynos: Add initial support for Samsung Galaxy S8
arm64: dts: exynos: Add initial support for exynos8895 SoC
dt-bindings: soc: samsung: exynos-pmu: Add exynos8895 compatible
dt-bindings: arm: samsung: Document dreamlte board binding
dt-bindings: arm: cpus: Add Samsung Mongoose M2
Link: https://lore.kernel.org/r/20241029081002.21106-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
dt-bindings: Changes for v6.13-rc1
This adds documentation for the AGX Orin industrial module.
* tag 'tegra-for-6.13-dt-bindings' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: arm: Tegra234 Industrial Module
Link: https://lore.kernel.org/r/20241025150555.2558582-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Document the RPMh Power Domains on the SM8750 Platform.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Message-ID: <20241112002444.2802092-2-quic_molvera@quicinc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Apparently there was some confusion regarding milliohm vs. megaohm.
(m/M). Use microohms to be able to properly specify the charger
resistor like other drivers do. This is not used yet by mainline code
yet. Specify a current sense resistor in milliohms range rather then
megaohms range in the examples.
CC: sre@kernel.org
Reported-by: Matti Vaittinen <mazziesaccount@gmail.com>
Closes: https://lore.kernel.org/imx/6dcd724a-a55c-4cba-a45b-21e76b1973b0@gmail.com/T/#mf590875a9f4d3955cd1041d7196ff0c65c0a7e9d
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: 1af5332fcf7c ("dt-bindings: mfd: Document ROHM BD71828 bindings")
Link: https://lore.kernel.org/r/20241111102701.358133-1-andreas@kemnade.info
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into soc/drivers
Arm SCMI updates for v6.13
Just couple of main additions:
1. Support for variable I/O width within ARM SCMI shared memory area.
Some shared memory areas might only support a certain access width,
such as 32-bit, which memcpy_{from,to}_io() does not adhere to at least
on ARM64 by making both 8-bit and 64-bit accesses to such memory.
This support updates the shmem layer to support reading from and
writing to such shared memory area using the specified I/O width
in the Device Tree. The various transport layers making use of the
shmem.c code are updated accordingly to pass the I/O accessors that
they store. The device tree bindings are also updated for the same.
2. Extension of SCMI transport bindings to add more properties
SCMI transports are characterized by a number of properties. The
values assumed by some of them tightly depend on the choices taken at
design time and on the overall archiecture of the specific platform:
things like timeouts, maximum message size and number of in-flight
messages are closely tied to the architecture of the platform like
number of SCMI agents on the system, physical memory available to the
SCMI platform and so on. Such details are not discoverable as they are
outside the scope of the SCMI protocol specification.
Currently such properties are simple default values defined at build
time, but the increasing number and variety of platforms using SCMI
with a wide range of designs has increased the need to have a way to
describe such properties across all these platforms.
Apart from the above two, there is one NULL pointer dereference fix for
very age old SCPI protocol driver which seems to be still in use on few
platforms.
* tag 'scmi-updates-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
firmware: arm_scmi: Relocate atomic_threshold to scmi_desc
firmware: arm_scmi: Use max_msg and max_msg_size devicetree properties
dt-bindings: firmware: arm,scmi: Introduce more transport properties
firmware: arm_scmi: Calculate virtio PDU max size dynamically
firmware: arm_scmi: Account for SHMEM memory overhead
firmware: arm_scmi: Support 'reg-io-width' property for shared memory
dt-bindings: sram: Document reg-io-width property
firmware: arm_scmi: Use vendor string in max-rx-timeout-ms
dt-bindings: firmware: arm,scmi: Add missing vendor string
firmware: arm_scmi: Reject clear channel request on A2P
firmware: arm_scmi: Fix slab-use-after-free in scmi_bus_notifier()
Link: https://lore.kernel.org/r/20241106110727.4007489-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Convert the Spreadtrum SC27xx PMIC bindings to DT schema. Adjust the
filename to match the compatible of the only in-tree user, SC2731.
Change #interrupt-cells value to 1, as according to [1] that is the
correct value.
Move partial examples of child nodes in the child node schemas to this new
MFD schema to have one complete example.
[1] https://lore.kernel.org/lkml/b6a32917d1e231277d240a4084bebb6ad91247e3.1550060544.git.baolin.wang@linaro.org/
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Link: https://lore.kernel.org/r/efd200c3b5b75405e4e450d064b026f10ae2f8e0.1730709384.git.stano.jakubek@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add documentation describing the Amlogic A4(A113L2) and A5(A113X2) RTC.
Signed-off-by: Yiting Deng <yiting.deng@amlogic.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://lore.kernel.org/r/20241112-rtc-v6-1-a71b60d2f354@amlogic.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add device tree schema for the Realtek RTL9300 switches. The RTL9300
family is made up of the RTL9301, RTL9302B, RTL9302C and RTL9303. These
have the same SoC differ in the Ethernet switch/SERDES arrangement.
Currently the only supported features are the syscon-reboot and i2c
controllers. The syscon-reboot is needed to be able to reboot the board.
The I2C controllers are slightly unusual because they each own an SCL
pin (GPIO8 for the first controller, GPIO 17 for the second) but have 8
common SDA pins which can be assigned to either controller (but not
both).
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241031200350.274945-5-chris.packham@alliedtelesis.co.nz
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Document the qcom,msm8917-tcsr compatible.
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241031-msm8917-v2-8-8a075faa89b1@mainlining.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Optional default-brightness property specifies brightness value to be
used if default LED state is on.
Signed-off-by: George Stark <gnstark@salutedevices.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241105185006.1380166-2-gnstark@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The Allwinner A523/T527 feature generic EHCI and OHCI compatible USB-2.0
host controllers (in addition to an MUSB and an XHCI controller).
Add the new name to the list of supported compatible strings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241111013033.22793-10-andre.przywara@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Allwinner A523/T527 SoCs have a MUSB controller fully compatible to
the D1 (and ultimately the A33), with five endpoints.
Add the new name to the list of compatible strings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241111013033.22793-9-andre.przywara@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fix dtbs_check errors in following files:
arch/arm64/boot/dts/marvell/armada-7040-db.dtb: sata@540000:
arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dtb: sata@540000:
arch/arm64/boot/dts/marvell/armada-8040-db.dtb: sata@540000:
arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtb: sata@540000:
arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dtb: sata@540000:
Unevaluated properties are not allowed ('iommus' was unexpected)
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241109094623.37518-4-linux@fw-web.de
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Introduce `mdio-parent-bus` property in the ksz DSA bindings to
reference the parent MDIO bus when the internal MDIO bus is attached to
it, bypassing the main management interface.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add description for the internal MDIO bus, including integrated PHY
nodes, to ksz DSA bindings.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PSCI reboot mode will map a mode name to multiple magic values instead
of just one. Convert the mode-.* property to an array. Users of the
reboot-mode schema will need to specify the maxItems of the mode-.*
properties. Existing users will all be 1.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Link: https://lore.kernel.org/r/20241107-arm-psci-system_reset2-vendor-reboots-v8-1-e8715fa65cb5@quicinc.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
