| Age | Commit message (Collapse) | Author |
|---|
|
The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220407143304.295610-1-krzysztof.kozlowski@linaro.org
|
|
The PRUSSs on AM57xx SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each PRUSS. The MDIO module used
within the PRU-ICSS is an instance of the MDIO Controller used
in TI Davinci SoCs. The same bus frequency of 1 MHz is chosen as
the regular MDIO node.
The nodes are added in the common am57-pruss.dtsi file and enabled
by default, but are disabled in all the existing AM57xx board dts
files. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
PRUSS Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
dra762 abz package is pin compatible with dra742 and few peripherals
like DDR with upgraded speed. Add dt support for this SoC.
Reported-by: Praneeth Bajjuri <praneeth@ti.com>
Tested-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[khilman: forward port from ti-linux-5.4.y]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
EMIF1 has ECC support, so add the DT node with address and interrupt
details to handle this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Switch all am571/2/4-idk boards to use new cpsw switch driver.
Those boards have 2 Ext. port wired and configured in dual_mac mode by
default. Hence, dual_mac mode has been preserved the same way between
legacy and new driver it's safe to switch drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since commit bcbb63b80284 ("ARM: dts: dra7: Separate AM57 dtsi files"),
the m_can node was inherited from dra76x.dtsi but the IP is not
connected on the idk board. Disable the node to reflect this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add DT nodes for new cpsw switchdev driver for am571x-idk board for now to
enable testing of the new solution.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM5 and DRA7 SoC families have different set of modules
in them so the SoC sepecific dtsi files need to be separated.
e.g. Some of the major differences between AM576 and DRA76
DRA76x AM576x
USB3 x
USB4 x
ATL x
VCP x
MLB x
ISS x
PRU-ICSS1 x
PRU-ICSS2 x
This patch only deals with disabling USB3, USB4 and ATL for
AM57 variants.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IO lines of MMC2 in am57xx-beagle-x15/am57xx-idk is connected to
3.3v. Use "ddr_3_3v" instead of "ddr_1_8v" to indicate DDR mode
works in 3.3v on these boards.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include dra76x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for am574x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am574x-idk.dts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am574x-idk is similar to am572x-idk with am574x SoC. So create
a common file for both evms and include SoC dtsi as needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
