| Age | Commit message (Collapse) | Author |
|---|
|
http://github.com/Broadcom/stblinux into fixes
Pull "Broadcom arm Device Tree fixes for 4.11 (part 2)" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.11,
please pull the following:
- Jon fixes a reboot issue on most Northstar Plus platforms by adding the
"open-source" property to the "gpio-restart" Device Tree nodes
* tag 'arm-soc/for-4.11/devicetree-fixes-2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: GPIO reboot open-source
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Fixes for 4.11:
- Fix USB host for sama5d2
- Fix cpuidle on sama5
* tag 'at91-ab-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: pm: cpu_idle: switch DDR to power-down mode
Revert "ARM: at91/dt: sama5d2: Use new compatible for ohci node"
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.11
A bunch of device tree fixes for various boards / SoCs.
* tag 'sunxi-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSI
ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
ARM: sun8i: Fix the mali clock rate
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.11:
- A fix to reboot hang seen on imx6sx-udoo-neo board, by removing
arm-supply and soc-supply and using LDO enabled mode.
* tag 'imx-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx-udoo-neo: Fix reboot hang
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The bl_en_pin GPIO pinmux is configured as "gpio_in", which makes it
conflicts with the real GPIO usage (out), and makes the backlight not
usable.
Drop the GPIO pinmux for it, thus this GPIO can be correctly used.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.
Fixes: d7b9eaff5f0c ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The libgpio code pre-sets the GPIO values for the gpio-reset in the
device tree. This results in the device being reset during bringup.
To prevent this pre-setting, use the "open-source" flag in the device
tree.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: b1aaf88 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625hr DTS file")
Fixes: 10baed1 ("ARM: dts: NSP: Add GPIO reboot method to bcm958625xmc DTS file")
Fixes: 088e3148 ("ARM: dts: NSP: Add new DT file for bcm958522er")
Fixes: e3227c1 ("ARM: dts: NSP: Add new DT file for bcm958525er")
Fixes: 2f8bc00 ("ARM: dts: NSP: Add new DT file for bcm958622hr")
Fixes: d454c37 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Fixes: f27eacf ("ARM: dts: NSP: Add new DT file for bcm988312hr")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.11-rc cycle:
- Fix smartreflex platform data regression where I accidentally
removed legacy platform data still in use
- Fix hypervisor mode for thumb2 kernel
- Fix misplaced tpic2810 to move it to right bus
- Enable INPUT_MOUSEDEV as a loadable module have mice working
- Fix use of gpio-key,wakeup and use wakeup-source instead as
this accidentally sneaked in during the merge window
- Fix error handling for onenand to properly return error
- Remove legacy gpmc-nand.c that's now dead code, this
also removes dependency to the MTD tree for further driver
changes
- Fix device node reference count errors for omap3 and
related to it also release device nodes after no longer
needed
* tag 'omap-for-v4.11/fixes-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Release device node after it is no longer needed.
ARM: OMAP2+: Fix device node reference counts
ARM: OMAP2+: Remove legacy gpmc-nand.c
ARM: OMAP2+: gpmc-onenand: propagate error on initialization failure
ARM: dts: am335x-pcm953: Fix legacy wakeup source binding
ARM: omap2plus_defconfig: Enable INPUT_MOUSEDEV as loadable modules
ARM: dts: am57xx-idk: tpic2810 is on I2C bus, not SPI
ARM: OMAP5 / DRA7: Fix HYP mode boot for thumb2 build
ARM: OMAP3: Fix smartreflex platform data regression
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for 4.11,
please pull the following:
- Jon fixes the UART output on the Broadcom bcm953012k reference board by
using the proper clock reference instead of hard-coding the baud rate
- Jon also fixes the memory map on the bcm953012k reference board by using
the appropriate physical RAM start address
- Jon finally fixes the interrupt type for the Cortex A9 global and local
timers found in the BCM5301X SoC (Norsthar).
* tag 'arm-soc/for-4.11/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This adds the AB8500 clocks to the device tree using the new
bindings from the clk subsystem, making audio work again.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
After issuing a 'reboot' command the imx6sx-udoo-neo board does not
reboot as expected and it just hangs instead.
In mainline kernel only LDO enabled mode is supported. Do not provide
arm-supply/soc-supply nodes in the device tree, so that the board operates
in LDO enabled mode and can then successfully reboot via watchdog.
Fixes: 76e691fc7653b85d39 ("ARM: dts: imx6sx: Add UDOO Neo support")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Linux 4.11-rc1
|
|
The Mali clock rate was improperly assumed to be 408MHz, while it was
really 384Mhz, 408MHz being the "extreme" frequency, and definitely not
stable.
Switch for the stable, correct frequency for the GPU.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Memory starts at 0x80000000, not 0. 0 "works" due to mirrior of the
first 128M of RAM to that address. Anything greater than 128M will
quickly find nothing there. Correcting the starting address has
everything working again.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: 7eb05f6d ("ARM: dts: bcm5301x: Add BCM SVK DT files")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The UARTs are outputting garbage on the console. This is due to a speed
issue. We can simply use the clock speed (which is now defined in the
DTSI file) and everything works fine.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: cdc36b22 ("ARM: dts: enable clock support for BCM5301X")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This reverts commit cab43282682e ("ARM: at91/dt: sama5d2: Use new
compatible for ohci node")
It depends from commit 7150bc9b4d43 ("usb: ohci-at91: Forcibly suspend
ports while USB suspend") which was reverted and implemented
differently. With the new implementation, the compatible string must
remain the same.
The compatible string introduced by this commit has been used in the
default SAMA5D2 dtsi starting from Linux 4.8. As it has never been
working correctly in an official release, removing it should not be
breaking the stability rules.
Fixes: cab43282682e ("ARM: at91/dt: sama5d2: Use new compatible for ohci node")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
cc: <stable@vger.kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
|
|
Replaced the legacy binding "gpio-key,wakeup" with "wakeup-source" as
noted in the kernel documentation.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit 50e95b6b854c ("ARM: dts: am57xx-idk: Add Industrial
output support") added the TPIC2810 device-tree node under
SPI bus instead of I2C1.
Fix it. Tested on AM572x IDK by driving on-board LEDs
connected to TPIC2810
Fixes: 50e95b6b854c ("ARM: dts: am57xx-idk: Add Industrial output support")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of new drivers, non-critical fixes, and updates
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (130 commits)
clk: renesas: mstp: ensure register writes complete
clk: qcom: Do not drop device node twice
clk: mvebu: adjust clock handling for the CP110 system controller
clk: mvebu: Expand mv98dx3236-core-clock support
clk: zte: add i2s clocks for zx296718
clk: sunxi-ng: sun9i-a80: Fix wrong pointer passed to PTR_ERR()
clk: sunxi-ng: select SUNXI_CCU_MULT for sun5i
clk: sunxi-ng: Check kzalloc() for errors and cleanup error path
clk: tegra: Add BPMP clock driver
clk: uniphier: add eMMC clock for LD11 and LD20 SoCs
clk: uniphier: add NAND clock for all UniPhier SoCs
ARM: dts: sun9i: Switch to new clock bindings
clk: sunxi-ng: Add A80 Display Engine CCU
clk: sunxi-ng: Add A80 USB CCU
clk: sunxi-ng: Add A80 CCU
clk: sunxi-ng: Support separately grouped PLL lock status register
clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
clk: qcom: SDHCI enablement on Nexus 5X / 6P
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_One
http://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wireless
https://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.html
http://www.savageboard.org/
http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ul
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"We sometimes collect non-critical fixes that come in during the later
part of the merge window in a branch for the next release instead, and
this is that contents for v4.11.
Most of these are OMAP fixes, dealing with OMAP36/37 detection, quirks
and setup. There's also some fixes for Davinci and a Kconfig fix for
SCPI to only enable on ARM{,64}"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
firmware: arm_scpi: Add hardware dependencies
ARM: OMAP3: Fix SoC detection of OMAP36/37 Family
ARM: OMAP5: Add HWMOD_SWSUP_SIDLE_ACT flag for UART
ARM: dts: Fix compatible for ti81xx uarts for 8250
ARM: dts: Fix am335x and dm814x scm syscon to probe children
ARM: OMAP2+: Fix init for multiple quirks for the same SoC
ARM: dts: Fix omap3 off mode pull defines
bus: da850-mstpri: fix my e-mail address
ARM: davinci: da850: fix da850_set_pll0rate()
ARM: davinci: da850: coding style fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty/serial driver patchset for 4.11-rc1.
Not much here, but a lot of little fixes and individual serial driver
updates all over the subsystem. Majority are for the sh-sci driver and
platform (the arch-specific changes have acks from the maintainer).
The start of the "serial bus" code is here as well, but nothing is
converted to use it yet. That work is still ongoing, hopefully will
start to show up across different subsystems for 4.12 (bluetooth is
one major place that will be used.)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (109 commits)
tty: pl011: Work around QDF2400 E44 stuck BUSY bit
atmel_serial: Use the fractional divider when possible
tty: Remove extra include in HVC console tty framework
serial: exar: Enable MSI support
serial: exar: Move register defines from uapi header to consumer site
serial: pci: Remove unused pci_boards entries
serial: exar: Move Commtech adapters to 8250_exar as well
serial: exar: Fix feature control register constants
serial: exar: Fix initialization of EXAR registers for ports > 0
serial: exar: Fix mapping of port I/O resources
serial: sh-sci: fix hardware RX trigger level setting
tty/serial: atmel: ensure state is restored after suspending
serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt
serdev: ttyport: check whether tty_init_dev() fails
serial: 8250_pci: make pciserial_detach_ports() static
ARM: dts: STiH410-b2260: Enable HW flow-control
ARM: dts: STiH407-family: Use new Pinctrl groups
ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control
ARM: dts: STiH410-b2260: Identify the UART RTS line
dt-bindings: serial: Update 'uart-has-rtscts' description
...
|
|
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new drivers:
- i.MX6 Video Data Order Adapter's (VDOA)
- Toshiba et8ek8 5MP sensor
- STM DELTA multi-format video decoder V4L2 driver
- SPI connected IR LED
- Mediatek IR remote receiver
- ZyDAS ZD1301 DVB USB interface driver
- new RC keymaps
- some very old LIRC drivers got removed from staging
- RC core gained support encoding IR scan codes
- DVB si2168 gained support for DVBv5 statistics
- lirc_sir driver ported to rc-core and promoted from staging
- other bug fixes, board additions and driver improvements
* tag 'media/v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (230 commits)
[media] mtk-vcodec: fix build warnings without DEBUG
[media] zd1301: fix building interface driver without demodulator
[media] usbtv: add sharpness control
[media] cxusb: Use a dma capable buffer also for reading
[media] ttpci: address stringop overflow warning
[media] dvb-usb-v2: avoid use-after-free
[media] add Hama Hybrid DVB-T Stick support
[media] et8ek8: Fix compiler / Coccinelle warnings
[media] media: fix semicolon.cocci warnings
[media] media: exynos4-is: add flags to dummy Exynos IS i2c adapter
[media] v4l: of: check for unique lanes in data-lanes and clock-lanes
[media] coda/imx-vdoa: constify structs
[media] st-delta: debug: trace stream/frame information & summary
[media] st-delta: add mjpeg support
[media] st-delta: EOS (End Of Stream) support
[media] st-delta: rpmsg ipc support
[media] st-delta: add memory allocator helper functions
[media] st-delta: STiH4xx multi-format video decoder v4l2 driver
[media] MAINTAINERS: add st-delta driver
[media] ARM: multi_v7_defconfig: enable STMicroelectronics DELTA Support
...
|
|
Pull "mvebu dt for 4.11 (part 4)" from Gregory CLEMENT:
Fix typos introduced during the preparation of the 4.11 merge window.
* tag 'mvebu-dt-4.11-4' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Few more late dts changes for omaps for v4.11 merge window" from Tony Lindgren:
- Add support for phyCORE-AM335x PCM-953 carrier board
- Add power button and charger support for am335x-chiliboard
* tag 'omap-for-v4.11/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: dts: Add support for phyCORE-AM335x PCM-953 carrier board
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "Enable SATA support on DA850 LCDK" from Sekhar Nori:
* tag 'davinci-for-v4.11/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: enable the SATA node
ARM: dts: da850: add the SATA node
devicetree: bindings: add bindings for ahci-da850
|
|
The switch to the new DSA binding used "marvell,mv88e6095" for the
compatible property which doesn't exist, use "marvell,mv88e6085"
instead.
Fixes: 455b82f03f52 ("ARM: dts: armada-385-linksys: Utilize new DSA binding")
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The compatible should be 98dx4251 not 98dx4521.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
|
|
This patch adds DT node for STMicroelectronics
DELTA V4L2 video decoder
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.11, part 2" from Maxime Ripard:
Support for the audio codec and Mali GPU for the A33
* tag 'sunxi-dt-for-4.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.11" from Maxime Ripard:
The usual chunk of DT changes, most notably:
- Support for the H2+ and the V3s
- CPUFreq support for the A33
- SPDIF support for the A31 and H3
- New boards: Beelink X2, Lichee Pi One, Lichee Pi Zero,
Orange Pi Zero
* tag 'sunxi-dt-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (42 commits)
ARM: dts: sun8i-h3: Add SPDIF to the Beelink X2
ARM: dts: sun8i-h3: Add the SPDIF block to the H3
ARM: dts: sun8i-h3: Add SPDIF TX pin to the H3
ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB
ARM: sun8i: sina33: Enable display
ARM: sun8i: a23/a33: Add the oscillators accuracy
ARM: sun8i: a23/a33: Enable the real LOSC and use it
ARM: dts: sunxi: add support for Lichee Pi Zero board
ARM: dts: sunxi: add dtsi file for V3s SoC
ARM: dts: sun6i: sina31s: Enable USB OTG controller in peripheral mode
ARM: dts: sun8i: reference-design: use AXP223 DTSI
ARM: dts: sun8i: parrot: use AXP223 DTSI
ARM: dts: sun8i: sina33: use AXP223 DTSI
ARM: dts: sun8i: a33-olinuxino: use AXP223 DTSI
ARM: dts: add DTSI for AXP223
dt-bindings: power: axp20x-usb: add axp223 compatible
ARM: dts: sun7i: Add wifi dt node on Banana Pro
ARM: dts: sun6i: Add SPDIF to the Mele I7
devicetree: bindings: Add vendor prefix for Shenzhen Xunlong Software
ARM: dts: sun8i-h3: orange-pi-pc: Enable audio codec
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
Pull "SoCFPGA DTS updates for v4.11, part 2" from Dinh Nguyen:
- Add AXI configuration for DWMAC ethernet controllers on Arria10
- Use watchdog1 instead of watchdog0 on Arria10
* tag 'socfpga_dts_for_v4.11_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: watchdog0 cannot reliably trigger reset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DeviceTree update for v4.11, third round" from Krzysztof Kozlowski
1. Add descriptive user-friendly label names for power domains. This
makes debugging easier.
* tag 'samsung-dt-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add labels to all existing power domains
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Pull "Ux500 Device Tree updates for v4.11" from Linus Walleij:
This cleans the device tree a bit and rectifies some
clocking bugs. They are in a sense regressions, but there
is no hurry for this platform.
* tag 'ux500-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: add the AB8500 sysclk to the device trees
ARM: dts: Ux500: move USB PHY pins to PHY device
ARM: dts: push MMC/SD to board and add comments
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
Pull "STM32 DT updates for v4.11, round 2" from Alexandre Torgue:
Highlights:
----------
- ADD Timers support on STM32F429 MCU
- Enable PWM1 & PWM3 on STM32F469 Disco board
- Fix STM32F4_X_CLOCK macro
- Use STM32F4_X_CLOCK macro in STM32 device tree
- Add I2C1 support for STM32F429 MCU
- Enable I2C1 on STM32F429 eval board
* tag 'stm32-dt-for-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
|
|
Merge "mvebu dt for 4.11 (part 3)" from Gregory CLEMENT:
Add support for Marvell switches with integrated CPUs based on Armada XP
* tag 'mvebu-dt-4.11-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
ARM: dts: mvebu: Add device tree for 98DX3236 SoCs
|
|
Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.
Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).
In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull "mvebu fixes for 4.10 (part 1)" from Gregory CLEMENT:
More consistent naming for some orion5x based boards helping the
switch to device tree for debian users.
* tag 'mvebu-fixes-4.10-1' of git://git.infradead.org/linux-mvebu:
ARM: orion5x: fix Makefile for linkstation-lschl.dtb
ARM: dts: orion5x-lschl: More consistent naming on linkstation series
ARM: dts: orion5x-lschl: Fix model name
|
|
Hardware flow-control capability must be specified at a platform
level in order to inform the ASC driver that the platform is capable
(i.e. are the lines wired up, etc). STiH4{07,10} devices are indeed
capable, so let's provide the property.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Having just defined some new Pinctrl groups for when HW flow-control
is {en,dis}abled, let's reference them for use within the driver.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Each serial port which supports HW flow-control should have 2 Pinctrl
groups. One for when HW flow-control is in progress, where the IP
will take over controlling the lines and another group which enables
the lines to be toggled using GPIO mechanisms.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When hardware flow-control is disabled, manual toggling of the UART's
reset line (RTS) using userland applications (e.g. stty) is not
possible, since the ASC IP does not provide this functionality in the
same was as some other IPs do. Thus, we have to do this manually.
This patch configures the UART RTS line as a GPIO for manipulation
within the UART driver when HW flow-control is not enabled.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable the audio codec and the audio dai for the sun8i A33 sinlinx board.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Enable the audio codec and the audio dai for the sun8i R16 Parrot board.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add the audio codec, dai and a simple card to be able to use the
audio stream of the builtin codec on sun8i SoC.
This commit adds also an audio-routing for the sound card node to link
the analog DAPM widgets (Right/Left DAC) and the digital one's as they
are created in different drivers.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add the device tree entries needed to support the EMAC AXI
bus settings on the Arria10 SoCFPGA chip.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
