| Age | Commit message (Collapse) | Author |
|---|
|
The check_spi_bus_bridge() in scripts/dtc/checks.c requires that the node
have "spi-slave" property must with "#address-cells = <0>" and
"#size-cells = <0>". But currently both "#address-cells" and "#size-cells"
properties are deleted, the corresponding default values are 2 and 1. As a
result, the check fails and below warnings is displayed.
arch/arm/boot/dts/mmp2.dtsi:472.23-480.6: Warning (spi_bus_bridge): \
/soc/apb@d4000000/spi@d4037000: incorrect #address-cells for SPI bus
also defined at arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts:225.7-237.3
arch/arm/boot/dts/mmp2.dtsi:472.23-480.6: Warning (spi_bus_bridge): \
/soc/apb@d4000000/spi@d4037000: incorrect #size-cells for SPI bus
also defined at arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts:225.7-237.3
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dtb: Warning (spi_bus_reg): \
Failed prerequisite 'spi_bus_bridge'
Because the value of "#size-cells" is already defined as zero in the node
"ssp3: spi@d4037000" in arch/arm/boot/dts/mmp2.dtsi. So we only need to
explicitly add "#address-cells = <0>" and keep "#size-cells" no change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201207084752.1665-2-thunder.leizhen@huawei.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
These definitions are evidently left over from the days when
sparsemem settings were platform specific. This was no longer
the case when the platform got merged.
There was no warning in the past, but now the asm/sparsemem.h
header ends up being included indirectly, causing this warning:
In file included from /git/arm-soc/arch/arm/mach-keystone/keystone.c:24:
arch/arm/mach-keystone/memory.h:10:9: warning: 'SECTION_SIZE_BITS' macro redefined [-Wmacro-redefined]
#define SECTION_SIZE_BITS 34
^
arch/arm/include/asm/sparsemem.h:23:9: note: previous definition is here
#define SECTION_SIZE_BITS 28
^
Clearly the definitions never had any effect here, so remove them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203231847.1484900-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, round 5:
- Fix a regression on SoC revision detection with ANATOP, that is
introduced by commit 4a4fb66119eb ("ARM: imx: Add missing
of_node_put()").
- Drop PAD_GPIO_6 from imx6qdl-wandboard ENET pin group, as the pin is
used by camera sensor now.
- Fix I2C3_SCL pinmux on imx6qdl-kontron-samx6i board, so that SoM EEPROM
can be accessed.
* tag 'imx-fixes-5.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-kontron-samx6i: fix I2C_PM scl pin
ARM: dts: imx6qdl-wandboard-revd1: Remove PAD_GPIO_6 from enetgrp
ARM: imx: Use correct SRC base address
Link: https://lore.kernel.org/r/20201201091820.GW4072@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A few more RGMII-ID fixes, and a bunch of other more random fixes
* tag 'sunxi-fixes-for-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: pcduino3-nano: enable RGMII RX/TX delay on PHY
ARM: dts: sun8i: v3s: fix GIC node memory range
ARM: dts: sun8i: v40: bananapi-m2-berry: Fix ethernet node
ARM: dts: sun8i: r40: bananapi-m2-berry: Fix dcdc1 regulator
ARM: dts: sun7i: bananapi: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: s3: pinecube: align compatible property to other S3 boards
ARM: sunxi: Add machine match for the Allwinner V3 SoC
arm64: dts: allwinner: h6: orangepi-one-plus: Fix ethernet
Link: https://lore.kernel.org/r/1280f1de-1b6d-4cc2-8448-e5a9096a41e8.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.10-rc7 that resolve a number of
reported issues, and add some new device ids.
Nothing major here, but these solve some problems that people were
having with the 5.10-rc tree:
- reverts for USB storage dma settings that broke working devices
- thunderbolt use-after-free fix
- cdns3 driver fixes
- gadget driver userspace copy fix
- new device ids
All of these except for the reverts have been in linux-next with no
reported issues. The reverts are "clean" and were tested by Hans, as
well as passing the 0-day tests"
* tag 'usb-5.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: f_fs: Use local copy of descriptors for userspace copy
usb: ohci-omap: Fix descriptor conversion
Revert "usb-storage: fix sdev->host->dma_dev"
Revert "uas: fix sdev->host->dma_dev"
Revert "uas: bump hw_max_sectors to 2048 blocks for SS or faster drives"
USB: serial: kl5kusb105: fix memleak on open
USB: serial: ch341: sort device-id entries
USB: serial: ch341: add new Product ID for CH341A
USB: serial: option: fix Quectel BG96 matching
usb: cdns3: core: fix goto label for error path
usb: cdns3: gadget: clear trb->length as zero after preparing every trb
usb: cdns3: Fix hardware based role switch
USB: serial: option: add support for Thales Cinterion EXS82
USB: serial: option: add Fibocom NL668 variants
thunderbolt: Fix use-after-free in remove_unplugged_switch()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Move -Wcast-align to W=3, which tends to be false-positive and there
is no tree-wide solution.
- Pass -fmacro-prefix-map to KBUILD_CPPFLAGS because it is a
preprocessor option and makes sense for .S files as well.
- Disable -gdwarf-2 for Clang's integrated assembler to avoid warnings.
- Disable --orphan-handling=warn for LLD 10.0.1 to avoid warnings.
- Fix undesirable line breaks in *.mod files.
* tag 'kbuild-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: avoid split lines in .mod files
kbuild: Disable CONFIG_LD_ORPHAN_WARN for ld.lld 10.0.1
kbuild: Hoist '--orphan-handling' into Kconfig
Kbuild: do not emit debug info for assembly with LLVM_IAS=1
kbuild: use -fmacro-prefix-map for .S sources
Makefile.extrawarn: move -Wcast-align to W=3
|
|
While I was doing zram testing, I found sometimes decompression failed
since the compression buffer was corrupted. With investigation, I found
below commit calls cond_resched unconditionally so it could make a
problem in atomic context if the task is reschedule.
BUG: sleeping function called from invalid context at mm/vmalloc.c:108
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 946, name: memhog
3 locks held by memhog/946:
#0: ffff9d01d4b193e8 (&mm->mmap_lock#2){++++}-{4:4}, at: __mm_populate+0x103/0x160
#1: ffffffffa3d53de0 (fs_reclaim){+.+.}-{0:0}, at: __alloc_pages_slowpath.constprop.0+0xa98/0x1160
#2: ffff9d01d56b8110 (&zspage->lock){.+.+}-{3:3}, at: zs_map_object+0x8e/0x1f0
CPU: 0 PID: 946 Comm: memhog Not tainted 5.9.3-00011-gc5bfc0287345-dirty #316
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1 04/01/2014
Call Trace:
unmap_kernel_range_noflush+0x2eb/0x350
unmap_kernel_range+0x14/0x30
zs_unmap_object+0xd5/0xe0
zram_bvec_rw.isra.0+0x38c/0x8e0
zram_rw_page+0x90/0x101
bdev_write_page+0x92/0xe0
__swap_writepage+0x94/0x4a0
pageout+0xe3/0x3a0
shrink_page_list+0xb94/0xd60
shrink_inactive_list+0x158/0x460
We can fix this by removing the ZSMALLOC_PGTABLE_MAPPING feature (which
contains the offending calling code) from zsmalloc.
Even though this option showed some amount improvement(e.g., 30%) in
some arm32 platforms, it has been headache to maintain since it have
abused APIs[1](e.g., unmap_kernel_range in atomic context).
Since we are approaching to deprecate 32bit machines and already made
the config option available for only builtin build since v5.8, lastly it
has been not default option in zsmalloc, it's time to drop the option
for better maintenance.
[1] http://lore.kernel.org/linux-mm/20201105170249.387069-1-minchan@kernel.org
Fixes: e47110e90584 ("mm/vunmap: add cond_resched() in vunmap_pmd_range")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Harish Sriram <harish@linux.ibm.com>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20201117202916.GA3856507@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There were a bunch of issues with the patch converting the
OMAP1 OSK board to use descriptors for controlling the USB
host:
- The chip label was incorrect
- The GPIO offset was off-by-one
- The code should use sleeping accessors
This patch tries to fix all issues at the same time.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 15d157e87443 ("usb: ohci-omap: Convert to use GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201130083033.29435-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, '--orphan-handling=warn' is spread out across four different
architectures in their respective Makefiles, which makes it a little
unruly to deal with in case it needs to be disabled for a specific
linker version (in this case, ld.lld 10.0.1).
To make it easier to control this, hoist this warning into Kconfig and
the main Makefile so that disabling it is simpler, as the warning will
only be enabled in a couple places (main Makefile and a couple of
compressed boot folders that blow away LDFLAGS_vmlinx) and making it
conditional is easier due to Kconfig syntax. One small additional
benefit of this is saving a call to ld-option on incremental builds
because we will have already evaluated it for CONFIG_LD_ORPHAN_WARN.
To keep the list of supported architectures the same, introduce
CONFIG_ARCH_WANT_LD_ORPHAN_WARN, which an architecture can select to
gain this automatically after all of the sections are specified and size
asserted. A special thanks to Kees Cook for the help text on this
config.
Link: https://github.com/ClangBuiltLinux/linux/issues/1187
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Use the correct pin for the i2c scl signal else we can't access the
SoM eeprom.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Bernd Bauer <bernd.bauer@anton-paar.com>
[m.felsch@pengutronix.de: Adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit 8ad2d1dcce54 ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera
support") the PAD_GPIO_6 is used for providing the camera sensor clock.
Remove it from the enetgrp to fix the following IOMXU conflict:
[ 9.972414] imx6q-pinctrl 20e0000.pinctrl: pin MX6Q_PAD_GPIO_6 already requested by 2188000.ethernet; cannot claim for 1-003c
[ 9.983857] imx6q-pinctrl 20e0000.pinctrl: pin-140 (1-003c) status -22
[ 9.990514] imx6q-pinctrl 20e0000.pinctrl: could not request pin 140 (MX6Q_PAD_GPIO_6) from group ov5645grp on device 20e0000.pinctrl
Fixes: 8ad2d1dcce54 ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit 4a4fb66119eb ("ARM: imx: Add missing of_node_put()") accidentally
forgot to rename a variable, which caused the wrong address to be used
and, in our case, the ULL getting falsely identified as ULZ.
Fixes: 4a4fb66119eb ("ARM: imx: Add missing of_node_put()")
Signed-off-by: Robert Karszniewicz <r.karszniewicz@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Two more places which invoke tracing from RCU disabled regions in the
idle path.
Similar to the entry path the low level idle functions have to be
non-instrumentable"
* tag 'locking-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intel_idle: Fix intel_idle() vs tracing
sched/idle: Fix arch_cpu_idle() vs tracing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fix from Arnd Bergmann:
"Add correct MAX_POSSIBLE_PHYSMEM_BITS setting to asm-generic.
This is a single bugfix for a bug that Stefan Agner found on 32-bit
Arm, but that exists on several other architectures"
* tag 'asm-generic-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: pgtable: define MAX_POSSIBLE_PHYSMEM_BITS where needed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of patches for devicetree files and Arm SoC specific
drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including one regression
for the CPSW network driver and a few runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform, in particular
fixing the MMC device ordering that recently became
nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including a regression
fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the NXP dpio driver
- A regression fix for a bug caused by an earlier bug fix in the
xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the NXP LPC32xx
platform"
* tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
optee: add writeback to valid memory type
firmware: xilinx: Use hash-table for api feature check
firmware: xilinx: Fix SD DLL node reset issue
soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
ARM: dts: dra76x: m_can: fix order of clocks
bus: ti-sysc: suppress err msg for timers used as clockevent/source
MAINTAINERS: Remove myself as LPC32xx maintainers
arm64: dts: qcom: clear the warnings caused by empty dma-ranges
arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for various issues noticed during the -rc cycle:
- Earlier omap4 cpuidle fix was incomplete and needs to use a
configured idle state instead
- Fix am4 cpsw driver compatible to avoid invalid resource error
for the legacy driver
- Two kconfig fixes for genpd support that we added for for v5.10
for proper location of the option and adding missing option
- Fix ti-sysc reset status checking on enabling modules to ignore
quirky modules with reset status only usable when the quirk is
activated during reset. Also fix bogus resetdone warning for
cpsw and modules with no sysst register reset status bit
- Suppress a ti-sysc warning for timers reserved as system timers
- Fix the ordering of clocks for dra7 m_can
* tag 'omap-for-v5.10/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra76x: m_can: fix order of clocks
bus: ti-sysc: suppress err msg for timers used as clockevent/source
ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
bus: ti-sysc: Fix bogus resetdone warning on enable for cpsw
bus: ti-sysc: Fix reset status check for modules with quirks
ARM: OMAP2+: Fix missing select PM_GENERIC_DOMAINS_OF
ARM: OMAP2+: Fix location for select PM_GENERIC_DOMAINS
Link: https://lore.kernel.org/r/pull-1606460270-864284@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We call arch_cpu_idle() with RCU disabled, but then use
local_irq_{en,dis}able(), which invokes tracing, which relies on RCU.
Switch all arch_cpu_idle() implementations to use
raw_local_irq_{en,dis}able() and carefully manage the
lockdep,rcu,tracing state like we do in entry.
(XXX: we really should change arch_cpu_idle() to not return with
interrupts enabled)
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lkml.kernel.org/r/20201120114925.594122626@infradead.org
|
|
The RX/TX delays for the Ethernet PHY on the Linksprite pcDuino 3 Nano
are configured in hardware, using resistors that are populated to pull
the RTL8211E's RXDLY/TXDLY pins low or high as needed.
phy-mode should be set to rgmii-id to reflect this. Previously it was
set to rgmii, which used to work but now results in the delays being
disabled again as a result of the bugfix in commit bbc4d71d6354 ("net:
phy: realtek: fix rtl8211e rx/tx delay config").
Tested on two pcDuino 3 Nano boards purchased in 2015. Without this fix,
Ethernet works unreliably on one board and doesn't work at all on the
other.
Fixes: 061035d456c9 ("ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board")
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201123174739.6809-1-ats@offog.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Borislav Petkov:
"Forwarded EFI fixes from Ard Biesheuvel:
- fix memory leak in efivarfs driver
- fix HYP mode issue in 32-bit ARM version of the EFI stub when built
in Thumb2 mode
- avoid leaking EFI pgd pages on allocation failure"
* tag 'efi-urgent-for-v5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Free efi_pgd with free_pages()
efivarfs: fix memory leak in efivarfs_create()
efi/arm: set HSCTLR Thumb2 bit correctly for HVC calls from HYP
|
|
Currently the GIC node in V3s DTSI follows some old DT examples, and
being broken. This leads a warning at boot.
Fix this.
Fixes: f989086ccbc6 ("ARM: dts: sunxi: add dtsi file for V3s SoC")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201120050851.4123759-1-icenowy@aosc.io
|
|
According to the bosch,m_can.yaml bindings the first clock shall be the "hclk",
while the second clock "cclk".
This patch fixes the order accordingly.
Fixes: 0adbe832f21a ("ARM: dts: dra76x: Add MCAN node")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed
to 'phy-mode="rgmii-id"' now, because the PHY drivers (realtek,
ksz9031, dp83867, ...) now configure the internal delay based on that
when they used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution
that would avoid breaking all boards, but that does not seem to be
happening any time soon, so I am now sending the correct version of
the dts files to ensure that at least these machines can use their
network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU operating
points to match the data sheet
- A revert for a dts patch that caused a regression in USB support on
Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak and
missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent for
correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems"
* tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: dts: exynos: revert "add input clock to CMU in Exynos4412 Odroid"
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
tee: amdtee: synchronize access to shm list
tee: amdtee: fix memory leak due to reset of global shm list
arm64: dts: agilex/stratix10: Fix qspi node compatible
ARM: dts: imx6q-prti6q: fix PHY address
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, round 4:
- Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch
device work reliably.
- Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
- Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match
hardware datasheet.
- Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board.
* tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
Link: https://lore.kernel.org/r/20201116090702.GM5849@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Stefan Agner reported a bug when using zsram on 32-bit Arm machines
with RAM above the 4GB address boundary:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = a27bd01c
[00000000] *pgd=236a0003, *pmd=1ffa64003
Internal error: Oops: 207 [#1] SMP ARM
Modules linked in: mdio_bcm_unimac(+) brcmfmac cfg80211 brcmutil raspberrypi_hwmon hci_uart crc32_arm_ce bcm2711_thermal phy_generic genet
CPU: 0 PID: 123 Comm: mkfs.ext4 Not tainted 5.9.6 #1
Hardware name: BCM2711
PC is at zs_map_object+0x94/0x338
LR is at zram_bvec_rw.constprop.0+0x330/0xa64
pc : [<c0602b38>] lr : [<c0bda6a0>] psr: 60000013
sp : e376bbe0 ip : 00000000 fp : c1e2921c
r10: 00000002 r9 : c1dda730 r8 : 00000000
r7 : e8ff7a00 r6 : 00000000 r5 : 02f9ffa0 r4 : e3710000
r3 : 000fdffe r2 : c1e0ce80 r1 : ebf979a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5383d Table: 235c2a80 DAC: fffffffd
Process mkfs.ext4 (pid: 123, stack limit = 0x495a22e6)
Stack: (0xe376bbe0 to 0xe376c000)
As it turns out, zsram needs to know the maximum memory size, which
is defined in MAX_PHYSMEM_BITS when CONFIG_SPARSEMEM is set, or in
MAX_POSSIBLE_PHYSMEM_BITS on the x86 architecture.
The same problem will be hit on all 32-bit architectures that have a
physical address space larger than 4GB and happen to not enable sparsemem
and include asm/sparsemem.h from asm/pgtable.h.
After the initial discussion, I suggested just always defining
MAX_POSSIBLE_PHYSMEM_BITS whenever CONFIG_PHYS_ADDR_T_64BIT is
set, or provoking a build error otherwise. This addresses all
configurations that can currently have this runtime bug, but
leaves all other configurations unchanged.
I looked up the possible number of bits in source code and
datasheets, here is what I found:
- on ARC, CONFIG_ARC_HAS_PAE40 controls whether 32 or 40 bits are used
- on ARM, CONFIG_LPAE enables 40 bit addressing, without it we never
support more than 32 bits, even though supersections in theory allow
up to 40 bits as well.
- on MIPS, some MIPS32r1 or later chips support 36 bits, and MIPS32r5
XPA supports up to 60 bits in theory, but 40 bits are more than
anyone will ever ship
- On PowerPC, there are three different implementations of 36 bit
addressing, but 32-bit is used without CONFIG_PTE_64BIT
- On RISC-V, the normal page table format can support 34 bit
addressing. There is no highmem support on RISC-V, so anything
above 2GB is unused, but it might be useful to eventually support
CONFIG_ZRAM for high pages.
Fixes: 61989a80fb3a ("staging: zsmalloc: zsmalloc memory allocation library")
Fixes: 02390b87a945 ("mm/zsmalloc: Prepare to variable MAX_PHYSMEM_BITS")
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/linux-mm/bdfa44bf1c570b05d6c70898e2bbb0acf234ecdf.1604762181.git.stefan@agner.ch/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of fixes for perf:
- A set of commits which reduce the stack usage of various perf
event handling functions which allocated large data structs on
stack causing stack overflows in the worst case
- Use the proper mechanism for detecting soft interrupts in the
recursion protection
- Make the resursion protection simpler and more robust
- Simplify the scheduling of event groups to make the code more
robust and prepare for fixing the issues vs. scheduling of
exclusive event groups
- Prevent event multiplexing and rotation for exclusive event groups
- Correct the perf event attribute exclusive semantics to take
pinned events, e.g. the PMU watchdog, into account
- Make the anythread filtering conditional for Intel's generic PMU
counters as it is not longer guaranteed to be supported on newer
CPUs. Check the corresponding CPUID leaf to make sure
- Fixup a duplicate initialization in an array which was probably
caused by the usual 'copy & paste - forgot to edit' mishap"
* tag 'perf-urgent-2020-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Fix Add BW copypasta
perf/x86/intel: Make anythread filter support conditional
perf: Tweak perf_event_attr::exclusive semantics
perf: Fix event multiplexing for exclusive groups
perf: Simplify group_sched_in()
perf: Simplify group_sched_out()
perf/x86: Make dummy_iregs static
perf/arch: Remove perf_sample_data::regs_user_copy
perf: Optimize get_recursion_context()
perf: Fix get_recursion_context()
perf/x86: Reduce stack usage for x86_pmu::drain_pebs()
perf: Reduce stack usage of perf_output_begin()
|
|
Pull ARM fix from Russell King:
"Just one bug fix: avoid a fortify panic when copying optprobe template"
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9019/1: kprobes: Avoid fortify_panic() when copying optprobe template
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Mostly some fixes for a fallout in a PHY driver that pointed out errors
in our DTs. Along with that, Jernej agreed to be a reviewer!
* tag 'sunxi-fixes-for-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: OrangePi Prime: Fix ethernet node
arm64: dts: allwinner: a64: bananapi-m64: Enable RGMII RX/TX delay on PHY
arm64: dts: allwinner: h5: libretech-all-h5-cc: Enable RGMII RX/TX delay on PHY
ARM: dts: sunxi: bananapi-m2-plus: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun9i: Enable both RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun8i: a83t: Enable both RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun8i: h3: orangepi-plus2e: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun7i: bananapi-m1-plus: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun7i: cubietruck: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: sun6i: a31-hummingbird: Enable RGMII RX/TX delay on Ethernet PHY
Revert "arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high"
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix ethernet node
arm64: dts: allwinner: h5: OrangePi PC2: Fix ethernet node
arm64: dts: allwinner: a64: Pine64 Plus: Fix ethernet node
arm64: dts: allwinner: a64: OrangePi Win: Fix ethernet node
arm64: dts: allwinner: Pine H64: Enable both RGMII RX/TX delay
arm64: dts: allwinner: beelink-gs1: Enable both RGMII RX/TX delay
arm64: dts: allwinner: pinetab: Drop unnecessary address/size-cells information
MAINTAINERS: Add Jernej Škrabec as a reviewer for Allwinner SoCs support
Link: https://lore.kernel.org/r/d1a1a6a6-fca4-4f1b-93b3-f2f6963b4e04.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.10, round 2
Highlights:
-----------
-Fixes are for DHCOM/DHCOR boards:
- Fix TA3-GPIO-C button
- Fix LED5 mapping
- Define VIO regulator supply on DHCOM
- Enable thermal sensor support on stm32mp15xx-dhcor
- Keep VDDA LDO1 always on to avoid leakage
* tag 'stm32-dt-for-v5.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
Link: https://lore.kernel.org/r/65bfc73d-aae1-5309-2e11-1e3da647ad46@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This reverts commit eaf2d2f6895d676dda6c95a652b58594f2887720.
The commit eaf2d2f6895d ("ARM: dts: exynos: add input clock to CMU in
Exynos4412 Odroid") breaks probing of usb3503 USB hub on Odroid U3.
It changes the order of clock drivers probe: the clkout (Exynos PMU)
driver is probed before the main clk-exynos4 driver. The clkout driver
on Exynos4412 depends on clk-exynos4 but it does not support deferred
probe, therefore this dependency and changed probe order causes probe
failure.
The usb3503 USB hub on Odroid U3 on the other hand requires clkout
clock. This can be seen in logs:
[ 5.007442] usb3503 0-0008: unable to request refclk (-517)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200921174818.15525-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, 3rd round:
- A series from Krzysztof Kozlowski to fix missing PMIC's interrupt
line pull-up for i.MX8MM and i.MX8MN boards.
- Set Bluetooth chip max-speed to 4000000 on imx8mm-beacon-som board
to fix the choppy Bluetooth audio sound.
- Remove non-existent OTG2, usbphynop2, and the usbmisc2 from i.MX8MN
device tree.
- Fix the endianness setting of RCPM node on Layerscape SoCs.
- Add the missing dma-coherent property for qoriq-fman device to improve
the performance.
- Fix the Ethernet PHY address on imx6q-prti6q board.
* tag 'imx-fixes-5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6q-prti6q: fix PHY address
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-ddr4-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-var-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-beacon-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-var-som: fix missing PMIC's interrupt line pull-up
Link: https://lore.kernel.org/r/20201030151821.GA28266@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix compatible the new CPSW switchdev DT node to avoid probing of legacy
CPSW driver which fails:
[ 2.781009] cpsw 4a100000.switch: invalid resource
Fixes: 7bf8f37aea82 ("ARM: dts: am437x-l4: add dt node for new cpsw switchdev driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The SPI chip selects are represented as:
cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>, <&gpio4 13 GPIO_ACTIVE_LOW>;
, which means that they are used in GPIO function instead of native
SPI mode.
Fix the IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
Fixes: c605cbf5e135 ("ARM: dts: imx: add device tree support for Freescale imx50evk board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
struct perf_sample_data lives on-stack, we should be careful about it's
size. Furthermore, the pt_regs copy in there is only because x86_64 is a
trainwreck, solve it differently.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Link: https://lkml.kernel.org/r/20201030151955.258178461@infradead.org
|
|
The VDDA LDO1 PMIC output supplies the analog VDDA input of the
STM32MP1 on DHCOM, keep it always on, otherwise there could be
leakage through the SoC.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable STM32 Digital Thermal Sensor driver for stm32mp15xx-dhcor SoMs.
Fixes: 94cafe1b6482 ("ARM: dts: stm32: Add Avenger96 devicetree support based on STM32MP157A")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The VIO regulator is supplied by PMIC Buck3, describe this in the DT.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On the prototype DHCOM, the LED5 was connected to pin PG2 of the
STM32MP15xx, however on the production SoM this was changed to pin
PC6. Update the connection in the DT.
Fixes: 81d5fc719798 ("ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On the prototype DHCOM, the TA3-GPIO-C button was connected to pin PI11 of
the STM32MP15xx, however on the production SoM this was changed to pin PG0
to free up the IRQ line 11 for LAN8710i PHY IRQ. Update the connection in
the DT. Since the IRQ line 0 is used for PMIC as well and cannot be shared
with the button, make the button polled.
Fixes: 87cabf9405cb ("ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
free_highpages() iterates over the free memblock regions in high
memory, and marks each page as available for the memory management
system.
Until commit cddb5ddf2b76 ("arm, xtensa: simplify initialization of
high memory pages") it rounded beginning of each region upwards and end of
each region downwards.
However, after that commit free_highmem() rounds the beginning and end of
each region downwards, and we may end up freeing a page that is
memblock_reserve()d, resulting in memory corruption.
Restore the original rounding of the region boundaries to avoid freeing
reserved pages.
Fixes: cddb5ddf2b76 ("arm, xtensa: simplify initialization of high memory pages")
Link: https://lore.kernel.org/r/20201029110334.4118-1-ardb@kernel.org/
Link: https://lore.kernel.org/r/20201031094345.6984-1-rppt@kernel.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Co-developed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Ethernet PHY on BananaPi M2 Berry provides RX and TX delays. Fix ethernet
node to reflect that fact.
Fixes: 27e81e1970a8 ("ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326769-39802-1-git-send-email-pgreco@centosproject.org
|
|
DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.
Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.
Fixes: 23edc168bd98 ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Berry")
Fixes: 27e81e1970a8 ("ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326755-39742-1-git-send-email-pgreco@centosproject.org
|
|
The Ethernet PHY on the Bananapi M1 has the RX and TX delays enabled on
the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8a5b272fbf44 ("ARM: dts: sun7i: Add Banana Pi board")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326600-39544-1-git-send-email-pgreco@centosproject.org
|
|
The compatible string in the Pine64 Pinecube dts diverges from the ones
used in other S3 based boards, like the LicheePi and the Elimo Impetus
and Initium. Discussion on LKML decided the PineCube should align to the
others.
Signed-off-by: Matteo Scordino <matteo.scordino@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201030234325.5865-7-matteo.scordino@gmail.com
|
|
The Allwinner V3 SoC shares the same base as the V3s but comes with
extra pins and features available. As a result, it has its dedicated
compatible string (already used in device trees), which is added here.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201031182137.1879521-2-contact@paulk.fr
|
|
Due to bug in the bootloader, the PHY has floating address and may
randomly change on each PHY reset. To avoid it, the updated bootloader
with the following patch[0] should be used:
| ARM: protonic: disable on-die termination to fix PHY bootstrapping
|
| If on-die termination is enabled, the RXC pin of iMX6 will be pulled
| high. Since we already have an 10K pull-down on board, the RXC level on
| PHY reset will be ~800mV, which is mostly interpreted as 1. On some
| reboots we get 0 instead and kernel can't detect the PHY properly.
|
| Since the default 0x020e07ac value is 0, it is sufficient to remove this
| entry from the affected imxcfg files.
|
| Since we get stable 0 on pin PHYADDR[2], the PHY address is changed from
| 4 to 0.
With latest bootloader update, the PHY address will be fixed to "0".
[0] https://git.pengutronix.de/cgit/barebox/commit/?id=93f7dcf631edfcda19e7757b28d66017ea274b81
Fixes: 0d446a505592 ("ARM: dts: add Protonic PRTI6Q board")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The ZII devel B board has two generations of Marvell Switches. The
mv88e6352 supports an MDIO clock of 12MHz. However the older 88e6185
does not like 12MHz, and often fails to probe.
Reduce the clock speed to 5MHz, which seems to work reliably.
Cc: Chris Healy <cphealy@gmail.com>
Fixes: b955387667ec ("ARM: dts: ZII: update MDIO speed and preamble")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") fixed micrel phy driver adding proper support for phy
modes. Adapt imx6q-udoo board phy settings : explicitly set required
delay configuration using "rgmii-id".
Fixes: cbd54fe0b2bc ("ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo")
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a fairly large set of bug fixes on top of -rc1, as most of
them were ready but didn't quite make it into the last-minute pull
requests for the merge window.
Allwinner:
- fix for incorrect CPU overtemperature limit
Amlogic:
- multiple smaller DT bugfixes, and missing device nodes
Marvell EBU:
- add missing aliases for ethernet switch ports on espressobin board
Marvell MMP:
- DTC warning fix
- bugfix for camera interface power-down
NXP i.MX:
- re-enable the GPIO driver on all defconfigs
ST STM32MP1:
- fix random crashes from incorrect voltage settings
Synaptics Berlin:
- enable the correct hardware timer driver
Texas Instruments K2G:
- fix a boot regression in the power domain code
TEE drivers:
- fix regression in TEE "login" method
SCMI drivers:
- multiple code fixes for corner cases in newly added code
MAINTAINERS file:
- move Kukjin Kim and Sangbeom Kim to credits (used to work on
Samsung Exynos)
- Masahiro Yamada is stepping down as Uniphier maintainer
I did not include a series of patches that work around a regression
caused by a bugfix in an ethernet phy driver that resulted in an
inadvertent DT binding change. This is still under discussion"
* tag 'arm-soc-fixes-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
soc: ti: ti_sci_pm_domains: check for proper args count in xlate
ARM: dts: stm32: Describe Vin power supply on stm32mp157c-edx board
ARM: dts: stm32: Describe Vin power supply on stm32mp15xx-dkx board
ARM: multi_v5_defconfig: Select CONFIG_GPIO_MXC
ARM: imx_v4_v5_defconfig: Select CONFIG_GPIO_MXC
ARM: dts: mmp2-olpc-xo-1-75: Use plural form of "-gpios"
ARM: dts: mmp3: Add power domain for the camera
arm64: berlin: Select DW_APB_TIMER_OF
dt-bindings: sram: sunxi-sram: add V3s compatible string
MAINTAINERS: Move Sangbeom Kim to credits
MAINTAINERS: Move Kukjin Kim to credits
MAINTAINERS: step down as maintainer of UniPhier SoCs and Denali driver
ARM: multi_v7_defconfig: Build in CONFIG_GPIO_MXC by default
ARM: imx_v6_v7_defconfig: Build in CONFIG_GPIO_MXC by default
arm64: defconfig: Build in CONFIG_GPIO_MXC by default
arm64: dts: meson: odroid-n2 plus: fix vddcpu_a pwm
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: amlogic: add missing ethernet reset ID
firmware: arm_scmi: Fix duplicate workqueue name
firmware: arm_scmi: Fix locking in notifications
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.10, round 1
Highlights:
-----------
-On STM32MP157 DK & ED boards: Add Vin supply description to avoid
random kernel crash due to vref_ddr regulator issue.
* tag 'stm32-dt-for-v5.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Describe Vin power supply on stm32mp157c-edx board
ARM: dts: stm32: Describe Vin power supply on stm32mp15xx-dkx board
Link: https://lore.kernel.org/r/4ac236b3-b980-f653-f644-53e586570724@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
