summaryrefslogtreecommitdiff
path: root/arch/mips/jz4740
AgeCommit message (Collapse)Author
2020-07-31MIPS: ingenic: Hardcode mem size for qi,lb60 boardPaul Cercueil
Old Device Tree for the qi,lb60 (aka. Ben Nanonote) did not have a 'memory' node. The kernel would then read the memory controller registers to know how much RAM was available. Since every other supported board has had a 'memory' node from the beginning, we can just hardcode a RAM size of 32 MiB when running with an old Device Tree without the 'memory' node. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-07-31MIPS: ingenic: Use fw_passed_dtb even if CONFIG_BUILTIN_DTBPaul Cercueil
The fw_passed_dtb is now properly initialized even when CONFIG_BUILTIN_DTB is used, so there's no need to handle it in any particular way here. Note that the behaviour is slightly different, as the previous code used the built-in Device Tree unconditionally, while now the built-in Device Tree is only used when the bootloader did not provide one. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-07-24MIPS: X2000: Add X2000 system type.周琰杰 (Zhou Yanjie)
1.Add "PRID_COMP_INGENIC_13" and "PRID_IMP_XBURST2" for X2000. 2.Add X2000 system type for cat /proc/cpuinfo to give out X2000. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-07-16MIPS: Ingenic: Add YSH & ATIL CU Neo board support.周琰杰 (Zhou Yanjie)
Add a device tree and a defconfig for the Ingenic X1830 based YSH & ATIL CU Neo board. Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-07-16MIPS: Ingenic: Add Ingenic X1830 support.周琰杰 (Zhou Yanjie)
Support the Ingenic X1830 SoC using the code under arch/mips/jz4740. This is left unselectable in Kconfig until a X1830 based board is added in a later commit. Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-07-16MIPS: ingenic: Add support for the RS90 boardPaul Cercueil
The RS-90, better known as RetroMini, is a small and pocketable handheld gaming console from YLMChina. It has little more than a JZ4725B SoC, a NAND, a screen, some buttons and a speaker. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-07-16MIPS: ingenic: Add support for the JZ4725B SoCPaul Cercueil
Add preliminary support for boards based on the JZ4725B SoC from Ingenic. The JZ4725B SoC is supposed to be older than the JZ4740 SoC, but its internals are much closer to what can be found on the JZ4750 and newer SoCs. It is low-power SoC with a MIPS32r1 SoC running at ~360 MHz, and no FPU. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-27MIPS: ingenic: Default to a generic boardPaul Cercueil
Having a generic board option makes it possible to create a kernel that will run on various Ingenic SoCs, as long as the right devicetree is provided. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-20MIPS: ingenic: Add missing includePaul Cercueil
Add missing include which adds the prototype to plat_time_init(). Fixes: f932449c11da ("MIPS: ingenic: Drop obsolete code, merge the rest in setup.c") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-13MIPS: Only include the platform file neededThomas Bogendoerfer
Instead of including all Platform files, we simply include the needed one and avoid clashes with makefile variables. Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-07MIPS: ingenic: Replace <linux/clk-provider.h> by <linux/of_clk.h>Geert Uytterhoeven
The JZ4740 setup code is not a clock provider, and just needs to call of_clk_init(). Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>. Fixes: f932449c11dabb4b ("MIPS: ingenic: Drop obsolete code, merge the rest in setup.c") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-04-29MIPS: ingenic: Drop obsolete code, merge the rest in setup.cPaul Cercueil
Drop a bootload of 10-years-old dirty code, that is not used anymore, as it has been replaced with clean code over the ages. Merge the very few bits left inside setup.c, so that everything is clean and tidy now. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-02-19MIPS: jz4740: Replace <linux/clk-provider.h> by <linux/of_clk.h>Geert Uytterhoeven
The Ingenic JZ4740 platform code is not a clock provider, and just needs to call of_clk_init(). Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: James Hartley <james.hartley@sondrel.com> Cc: John Crispin <john@phrozen.org> Cc: linux-mips@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Cc: linux-clk@vger.kernel.org Cc: linux-kernel@vger.kernel.org
2020-01-09MIPS: X1830: Add X1830 system type.周琰杰 (Zhou Yanjie)
1.Add X1830 system type for cat /proc/cpuinfo to give out X1830. 2.Change "PRID_IMP_XBURST" to "PRID_IMP_XBURST_REV1" and add a new "PRID_IMP_XBURST_REV2" for new Ingenic CPUs which has XBurst with MXU2 SIMD ISA. Notice: 1."PRID_IMP_XBURST_REV2" is corresponds to the latest XBurst processor with 128bit MXU2 SIMD instruction set, not the upcoming XBurst2 processor. This version of the processors fixes issues such as BTB and HPTLB. 2.In order to simplify and reuse the code, the "c->cputype" and the "c->writecombine" and the "__cpu_name[cpu]" in the original "PRID_IMP_XBURST" (now is "PRID_IMP_XBURST_REV1") are removed, and the corresponding settings are abtained through fall-through to "PRID_IMP_XBURST_REV2", which will cause the name that was previously mistakenly called "JZRISC" to become to the real name "XBurst". Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: yamada.masahiro@socionext.com Cc: tglx@linutronix.de Cc: chenhc@lemote.com Cc: tbogendoerfer@suse.de Cc: paul.burton@mips.com Cc: paul@crapouillou.net Cc: jhogan@kernel.org Cc: fancer.lancer@gmail.com Cc: ralf@linux-mips.org Cc: jiaxun.yang@flygoat.com
2020-01-09MIPS: Ingenic: Add YSH & ATIL CU Neo board support.周琰杰 (Zhou Yanjie)
Add a device tree for the Ingenic X1000 based YSH & ATIL CU Neo board. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Acked-by: Paul Cercueil <paul@crapouillou.net> [paulburton@kernel.org: Drop stale mention of previously unselectable Kconfig entry.] Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: robh+dt@kernel.org Cc: paul.burton@mips.com Cc: jhogan@kernel.org Cc: mripard@kernel.org Cc: shawnguo@kernel.org Cc: mark.rutland@arm.com Cc: alexandre.belloni@bootlin.com Cc: ralf@linux-mips.org Cc: heiko@sntech.de Cc: icenowy@aosc.io Cc: ak@linux.intel.com Cc: laurent.pinchart@ideasonboard.com Cc: krzk@kernel.org Cc: geert+renesas@glider.be Cc: prasannatsmkumar@gmail.com Cc: keescook@chromium.org Cc: ebiederm@xmission.com Cc: sernia.zhou@foxmail.com Cc: zhenwenjin@gmail.com Cc: 772753199@qq.com
2020-01-09MIPS: Ingenic: Add Ingenic X1000 support.周琰杰 (Zhou Yanjie)
Support the Ingenic X1000 SoC using the code under arch/mips/jz4740. This is left unselectable in Kconfig until a X1000 based board is added in a later commit. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: robh+dt@kernel.org Cc: paul.burton@mips.com Cc: jhogan@kernel.org Cc: mripard@kernel.org Cc: shawnguo@kernel.org Cc: mark.rutland@arm.com Cc: alexandre.belloni@bootlin.com Cc: ralf@linux-mips.org Cc: heiko@sntech.de Cc: icenowy@aosc.io Cc: ak@linux.intel.com Cc: laurent.pinchart@ideasonboard.com Cc: krzk@kernel.org Cc: geert+renesas@glider.be Cc: paul@crapouillou.net Cc: prasannatsmkumar@gmail.com Cc: keescook@chromium.org Cc: ebiederm@xmission.com Cc: sernia.zhou@foxmail.com Cc: zhenwenjin@gmail.com Cc: 772753199@qq.com
2019-08-08Merge branch 'ingenic-tcu-v5.4' into mips-nextPaul Burton
Merge the Ingenic TCU patchset from the ingenic-tcu-v5.4 branch which was created to enable follow-on changes in other subsystems. Signed-off-by: Paul Burton <paul.burton@mips.com>
2019-08-08MIPS: jz4740: Drop obsolete codePaul Cercueil
The old clocksource/timer platform code is now obsoleted by the newly introduced TCU drivers. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Tested-by: Mathieu Malaterre <malat@debian.org> Tested-by: Artur Rojek <contact@artur-rojek.eu> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Lee Jones <lee.jones@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-doc@vger.kernel.org Cc: linux-mips@vger.kernel.org Cc: linux-clk@vger.kernel.org Cc: od@zcrc.me
2019-07-30MIPS: jz4740: Drop dead codePaul Cercueil
Remove all the source files that are not used anywhere anymore. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Tested-by: Artur Rojek <contact@artur-rojek.eu> Signed-off-by: Paul Burton <paul.burton@mips.com>
2019-07-30MIPS: qi_lb60: Migrate to devicetreePaul Cercueil
Move all the platform data to devicetree. The only bit dropped is the PWM beeper, which requires the PWM driver to be updated. I figured it's okay to remove it here since it's really a non-critical device, and it'll be re-introduced soon enough. The other change is the CS line of the SPI is now set as active low. The SPI core would have forced "active low" anyway, unless the 'spi-cs-high' property is set. In the process of moving to devicetree, we also switched to new drivers: - We use the simple-audio-card and simple-amplifier drivers instead of the custom ASoC code; - We use the new Ingenic DRM driver coupled with the GiantPlus GPM940B0 DRM panel driver instead of the old framebuffer driver; - We use the new jz4780-dma driver instead of the old jz4740-dma one; - We use the ingenic-nand and jz4740-ecc drivers instead of the old jz4740-nand driver; - We use ingenic-battery instead of jz4740-battery; - We use iio-hwmon instead of jz4740-hwmon; - We use ingenic-iio instead of the old jz4740-adc MFD driver. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Tested-by: Artur Rojek <contact@artur-rojek.eu> [paul.burton@mips.com: Drop the unused & undocumented ili8960 spi@0 node.] Signed-off-by: Paul Burton <paul.burton@mips.com>
2019-07-30MIPS: X1000: Add X1000 system type.Zhou Yanjie
Add X1000 system type for cat /proc/cpuinfo to give out X1000. Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: ralf@linux-mips.org Cc: paul@crapouillou.net Cc: jhogan@kernel.org Cc: fancer.lancer@gmail.com Cc: chenhc@lemote.com Cc: tglx@linutronix.de Cc: gregkh@linuxfoundation.org Cc: armijn@tjaldur.nl Cc: syq@debian.org Cc: jiaxun.yang@flygoat.com
2019-07-22MIPS: qi_lb60: Move MMC configuration to devicetreePaul Cercueil
Move the MMC configuration from the board C file to devicetree. The 'power' GPIO was removed and instead the vmmc regulator is used, to follow the changes introduced in the jz4740-mmc driver. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Paul Burton <paul.burton@mips.com>
2019-07-17Merge tag 'clk-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk updates from Stephen Boyd: "This round of clk driver and framework updates is heavy on the driver update side. The two main highlights in the core framework are the addition of an bulk clk_get API that handles optional clks and an extra debugfs file that tells the developer about the current parent of a clk. The driver updates are dominated by i.MX in the diffstat, but that is mostly because that SoC has started converting to the clk_hw style of clk registration. The next big update is in the Amlogic meson clk driver that gained some support for audio, cpu, and temperature clks while fixing some PLL issues. Finally, the biggest thing that stands out is the conversion of a large part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses less strings and more pointer comparisons to match clk parents and children up. In general, it looks like we have a lot of little fixes and tweaks here and there to clk data along with the normal addition of a handful of new drivers and a couple new core framework features. Core: - Add a 'clk_parent' file in clk debugfs - Add a clk_bulk_get_optional() API (with devm too) New Drivers: - Support gated clk controller on MIPS based BCM63XX SoCs - Support SiLabs Si5341 and Si5340 chips - Support for CPU clks on Raspberry Pi devices - Audsys clock driver for MediaTek MT8516 SoCs Updates: - Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme - Small frequency support for SiLabs Si544 chips - Slow clk support for AT91 SAM9X60 SoCs - Remove dead code in various clk drivers (-Wunused) - Support for Marvell 98DX1135 SoCs - Get duty cycle of generic pwm clks - Improvement in mmc phase calculation and cleanup of some rate defintions - Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs - Add GPIO, SNVS and GIC clocks for i.MX8 drivers - Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock - Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting - Add clks for new Exynos5422 Dynamic Memory Controller driver - Clock definition for Exynos4412 Mali - Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3 - Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M - Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs - TI clock probing done from DT by default instead of firmware - Fix Amlogic Meson mpll fractional part and spread sprectrum issues - Add Amlogic meson8 audio clocks - Add Amlogic g12a temperature sensors clocks - Add Amlogic g12a and g12b cpu clocks - Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N - Add CMM (Color Management Module) clocks on Renesas R-Car M3-W - Add Clock Domain support on Renesas RZ/N1" * tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits) clk: consoldiate the __clk_get_hw() declarations clk: sprd: Add check for return value of sprd_clk_regmap_init() clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK clk: Add Si5341/Si5340 driver dt-bindings: clock: Add silabs,si5341 clk: clk-si544: Implement small frequency change support clk: add BCM63XX gated clock controller driver devicetree: document the BCM63XX gated clock bindings clk: at91: sckc: use dedicated functions to unregister clock clk: at91: sckc: improve error path for sama5d4 sck registration clk: at91: sckc: remove unnecessary line clk: at91: sckc: improve error path for sam9x5 sck register clk: at91: sckc: add support to free slow clock osclillator clk: at91: sckc: add support to free slow rc oscillator clk: at91: sckc: add support to free slow oscillator clk: rockchip: export HDMIPHY clock on rk3228 clk: rockchip: add watchdog pclk on rk3328 clk: rockchip: add clock id for hdmi_phy special clock on rk3228 clk: rockchip: add clock id for watchdog pclk on rk3328 clk: at91: sckc: add support for SAM9X60 ...
2019-07-17Merge tag 'mips_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linuxLinus Torvalds
Pull MIPS updates from Paul Burton: "A light batch this time around but significant improvements for certain systems: - Removal of readq & writeq for MIPS32 kernels where they would simply BUG() anyway, allowing drivers or other code that #ifdefs on their presence to work properly. - Improvements for Ingenic JZ4740 systems, including support for the external memory controller & pinmuxing fixes for qi_lb60/NanoNote systems. - Improvements for Lantiq systems, in particular around SMP & IPIs. - DT updates for ralink/MediaTek MT7628a systems to probe & configure a bunch more devices. - Miscellaneous cleanups & build fixes" * tag 'mips_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (30 commits) MIPS: fix some more fall through errors in arch/mips MIPS: perf events: handle switch statement falling through warnings mips/kprobes: Export kprobe_fault_handler() MAINTAINERS: Add myself as Ingenic SoCs maintainer MIPS: ralink: mt7628a.dtsi: Add watchdog controller DT node MIPS: ralink: mt7628a.dtsi: Add SPI controller DT node MIPS: ralink: mt7628a.dtsi: Add GPIO controller DT node MIPS: ralink: mt7628a.dtsi: Add pinctrl DT properties to the UART nodes MIPS: ralink: mt7628a.dtsi: Add pinmux DT node MIPS: ralink: mt7628a.dtsi: Add SPDX GPL-2.0 license identifier MIPS: lantiq: Add SMP support for lantiq interrupt controller MIPS: lantiq: Shorten register names, remove unused macros MIPS: lantiq: Fix bitfield masking MIPS: lantiq: Remove unused macros MIPS: lantiq: Fix attributes of of_device_id structure MIPS: lantiq: Change variables to the same type as the source MIPS: lantiq: Move macro directly to iomem function mips: Remove q-accessors from non-64bit platforms FDDI: defza: Include linux/io-64-nonatomic-lo-hi.h MIPS: configs: Remove useless UEVENT_HELPER_PATH ...
2019-06-25MIPS: Remove dead codePaul Cercueil
Remove the unused <asm/mach-jz4740/clock.h> include. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2019-06-25MIPS: jz4740: PM: Let CGU driver suspend clocks and set sleep modePaul Cercueil
Instead of forcing the jz4740 clocks to suspend here, we let the CGU driver handle it. We also let the CGU driver set the "sleep mode" bit. This has the added benefit that now it is possible to build a kernel on SoCs newer than the JZ4740 with CONFIG_PM. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2019-06-11MIPS: lb60: Fix pin mappingsPaul Cercueil
The pin mappings introduced in commit 636f8ba67fb6 ("MIPS: JZ4740: Qi LB60: Add pinctrl configuration for several drivers") are completely wrong. The pinctrl driver name is incorrect, and the function and group fields are swapped. Fixes: 636f8ba67fb6 ("MIPS: JZ4740: Qi LB60: Add pinctrl configuration for several drivers") Cc: <stable@vger.kernel.org> Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: od@zcrc.me Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 151Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 675 mass ave cambridge ma 02139 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 35 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Armijn Hemel <armijn@tjaldur.nl> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 or later as published by the free software foundation extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 9 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154040.848507137@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-21MIPS: ingenic: Add support for appended devicetreePaul Cercueil
Add support for booting the kernel from an externally-appended devicetree, if no devicetree was built-in. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org
2018-12-17mmc: jz4740: Use GPIO descriptor for powerLinus Walleij
The power GPIO line is passed with inversion flags and all from the platform data. Switch to using an optional GPIO descriptor and use this to switch the power. Augment the only boardfile to pass in the proper "power" descriptor in the GPIO descriptor machine table instead. As the GPIO handling is now much simpler, we can cut down on some overhead code. Cc: Paul Cercueil <paul@crapouillou.net> Cc: linux-mips@linux-mips.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-12-17mmc: jz4740: Get CD/WP GPIOs from descriptorsLinus Walleij
Modifty the JZ4740 driver to retrieve card detect and write protect GPIO pins from GPIO descriptors instead of hard-coded global numbers. Augment the only board file using this in the process and cut down on passed in platform data. Preserve the code setting the caps2 flags for CD and WP as active low or high since the slot GPIO code currently ignores the gpiolib polarity inversion semantice and uses the raw accessors to read the GPIO lines, but set the right polarity flags in the descriptor table for jz4740. Cc: Paul Cercueil <paul@crapouillou.net> Cc: linux-mips@linux-mips.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-08-14Merge tag 'mtd/for-4.19' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull mtd updates from Boris Brezillon: "JFFS2 changes: - Support 64-bit timestamps MTD core changes: - Support sub-partitions - Clarify mtd_oob_ops documentation - Make Kconfig formatting consistent - Fix potential overflows in mtdchar_{write,read}() - Fallback to ->_{read,write}() when ->_{read,write}_oob() is missing and no OOB data were requested - Remove VLA usage in the bch lib MTD driver changes: - Use mtd_device_register() instead of mtd_device_parse_register() where applicable - Use proper printk format to print physical addresses in the solutionengine driver - Add missing mtd_set_of_node() call in the powernv driver - Remove unneeded variables in a few drivers - Plug the TRX part parser to the DT partition parsers logic - Check ioremap_cache() return code in the gpio-addr-flash driver - Stop using VMLINUX_SYMBOL_STR() in gen_probe.c SPI NOR core changes: - Apply reset hacks only when reset is explicitly marked as broken in the DT SPI NOR driver changes: - Minor cleanup/fixes in the m25p80 driver - Release flash_np in the nxp-spifi driver - Add suspend/resume hooks to the atmel-quadspi driver - Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver - Use %pK instead of %p in the stm32-quadspi driver - Improve timeout handling in the cadence-quadspi driver - Use mtd_device_register() instead of mtd_device_parse_register() in the intel-spi driver NAND core changes: - Add the SPI-NAND framework. - Create a helper to find the best ECC configuration. - Create NAND controller operations. - Allocate dynamically ONFI parameters structure. - Add defines for ONFI version bits. - Add manufacturer fixup for ONFI parameter page. - Add an option to specify NAND chip as a boot device. - Add Reed-Solomon error correction algorithm. - Better name for the controller structure. - Remove unused caller_is_module() definition. - Make subop helpers return unsigned values. - Expose _notsupp() helpers for raw page accessors. - Add default values for dynamic timings. - Kill the chip->scan_bbt() hook. - Rename nand_default_bbt() into nand_create_bbt(). - Start to clean the nand_chip structure. - Remove stale prototype from rawnand.h. Raw NAND controllers drivers changes: - Qcom: structuring cleanup. - Denali: use core helper to find the best ECC configuration. - Possible build of almost all drivers by adding a dependency on COMPILE_TEST for almost all of them in Kconfig, implies various fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even changes in sparc64 and ia64 architectures. - Clean the ->probe() functions error path of a lot of drivers. - Migrate all drivers to use nand_scan() instead of nand_scan_ident()/nand_scan_tail() pair. - Use mtd_device_register() where applicable to simplify the code. - Marvell: * Handle on-die ECC. * Better clocks handling. * Remove bogus comment. * Add suspend and resume support. - Tegra: add NAND controller driver. - Atmel: * Add module param to avoid using dma. * Drop Wenyou Yang from MAINTAINERS. - Denali: optimize timings handling. - FSMC: Stop using chip->read_buf(). - FSL: * Switch to SPDX license tag identifiers. * Fix qualifiers in MXC init functions. Raw NAND chip drivers changes: - Micron: * Add fixup for ONFI revision. * Update ecc_stats.corrected. * Make ECC activation stateful. * Avoid enabling/disabling ECC when it can't be disabled. * Get the actual number of bitflips. * Allow forced on-die ECC. * Support 8/512 on-die ECC. * Fix on-die ECC detection logic. - Hynix: * Fix decoding the OOB size on H27UCG8T2BTR. * Use ->exec_op() in hynix_nand_reg_write_op()" * tag 'mtd/for-4.19' of git://git.infradead.org/linux-mtd: (188 commits) mtd: rawnand: atmel: Select GENERIC_ALLOCATOR MAINTAINERS: drop Wenyou Yang from Atmel NAND driver support mtd: rawnand: allocate dynamically ONFI parameters during detection mtd: spi-nor: only apply reset hacks to broken hardware mtd: spi-nor: cadence-quadspi: fix timeout handling mtd: spi-nor: atmel-quadspi: Include gpio/consumer.h instead of gpio.h mtd: spi-nor: intel-spi: use mtd_device_register() mtd: spi-nor: stm32-quadspi: replace "%p" with "%pK" mtd: spi-nor: atmel-quadspi: add suspend/resume hooks mtd: rawnand: allocate model parameter dynamically mtd: rawnand: do not export nand_scan_[ident|tail]() anymore mtd: rawnand: txx9ndfmc: convert driver to nand_scan() mtd: rawnand: txx9ndfmc: clarify ECC parameters assignation mtd: rawnand: tegra: convert driver to nand_scan() mtd: rawnand: jz4740: convert driver to nand_scan() mtd: rawnand: jz4740: group nand_scan_{ident, tail} calls mtd: rawnand: jz4740: fix probe function error path mtd: rawnand: docg4: convert driver to nand_scan() mtd: rawnand: do not execute nand_scan_ident() if maxchips is zero mtd: rawnand: atmel: convert driver to nand_scan() ...
2018-07-23MIPS: jz4740: Bump zload addressPaul Cercueil
Having the zload address at 0x8060.0000 means the size of the uncompressed kernel cannot be bigger than around 6 MiB, as it is deflated at address 0x8001.0000. This limit is too small; a kernel with some built-in drivers and things like debugfs enabled will already be over 6 MiB in size, and so will fail to extract properly. To fix this, we bump the zload address from 0x8060.0000 to 0x8100.0000. This is fine, as all the boards featuring Ingenic JZ SoCs have at least 32 MiB of RAM, and use u-boot or compatible bootloaders which won't hardcode the load address but read it from the uImage's header. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/19787/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
2018-07-18MIPS: jz4740: Move jz4740_nand.h header to include/linux/platform_data/jz4740Boris Brezillon
This way we will be able to compile the jz4740_nand driver when COMPILE_TEST=y. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-05-14MIPS: JZ4740: Drop old platform reset codePaul Cercueil
This work is now performed by the watchdog driver directly. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Acked-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Wim Van Sebroeck <wim@linux-watchdog.org> Cc: Mathieu Malaterre <malat@debian.org> Cc: linux-mips@linux-mips.org Cc: linux-watchdog@vger.kernel.org Signed-off-by: James Hogan <jhogan@kernel.org>
2018-05-14MIPS: JZ4740: dts: Add bindings for the jz4740-wdt driverPaul Cercueil
Also remove the watchdog platform_device from platform.c, since it wasn't used anywhere anyway. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Wim Van Sebroeck <wim@linux-watchdog.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Malaterre <malat@debian.org> Cc: linux-mips@linux-mips.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org [jhogan@kernel.org: Drop jz4740_wdt_device declaration from header] Signed-off-by: James Hogan <jhogan@kernel.org>
2018-02-14spi: spi-gpio: Rewrite to use GPIO descriptorsLinus Walleij
This converts the bit-banged GPIO SPI driver to looking up and using GPIO descriptors to get a handle on GPIO lines for SCK, MOSI, MISO and all CS lines. All existing board files are converted in one go to keep it all consistent. With these conversions I rarely find any interrim steps that makes any sense. Device tree probing and GPIO handling should work like before also after this patch. For board files, we stop using controller data to pass the GPIO line for chip select, instead we pass this as a GPIO descriptor lookup like everything else. In some s3c24xx machines the names of the SPI devices were set to "spi-gpio" rather than "spi_gpio" which can never have worked, I fixed it working (I guess) as part of this patch set. Sometimes I wonder how this code got upstream in the first place, it obviously is not tested. mach-s3c64xx/mach-smartq.c has the same problem and additionally defines the *same* GPIO line for MOSI and MISO which is not going to be accepted by gpiolib. As the lines were number 1,2,2 I assumed it was a typo and use lines 1,2,3. A comment gives awat that line 0 is chip select though no actual SPI device is provided for the LCD supposed to be on this bit-banged SPI bus. I left it intact instead of just deleting the bus though. Kill off board file code that try to initialize the SPI lines to the same values that they will later be set by the spi_gpio driver anyways. Given the huge number of weird things in these board files I do not think this code is very tested or put in with much afterthought anyways. In order to assert that we do not get performance regressions on this crucial bing-banged driver, a ran a script like this dumping the Ilitek ILI9322 regmap 10000 times (it has no caching obviously) on an otherwise idle system in two iterations before and after the patches: #!/bin/sh for run in `seq 10000` do cat /debug/regmap/spi0.0/registers > /dev/null done Before the patch: time test.sh real 3m 41.03s user 0m 29.41s sys 3m 7.22s time test.sh real 3m 44.24s user 0m 32.31s sys 3m 7.60s After the patch: time test.sh real 3m 41.32s user 0m 28.92s sys 3m 8.08s time test.sh real 3m 39.92s user 0m 30.20s sys 3m 5.56s So any performance differences seems to be in the error margin. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-01-18MIPS: ingenic: Initial GCW Zero supportPaul Cercueil
The GCW Zero (http://www.gcw-zero.com) is a retro-gaming focused handheld game console, successfully kickstarted in ~2012, running Linux. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Mathieu Malaterre <malat@debian.org> Acked-by: Philippe Ombredanne <pombredanne@nexb.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Maarten ter Huurne <maarten@treewalker.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/18490/ Signed-off-by: James Hogan <jhogan@kernel.org>
2018-01-18MIPS: ingenic: Initial JZ4770 supportPaul Cercueil
Provide just enough bits (clocks, clocksource, uart) to allow a kernel to boot on the JZ4770 SoC to a initramfs userspace. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com> Reviewed-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Maarten ter Huurne <maarten@treewalker.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/18487/ Signed-off-by: James Hogan <jhogan@kernel.org>
2018-01-18MIPS: ingenic: Detect machtype from SoC compatible stringPaul Cercueil
Previously, the mips_machtype variable was always initialized to MACH_INGENIC_JZ4740 even if running on different SoCs. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Maarten ter Huurne <maarten@treewalker.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/18486/ Signed-off-by: James Hogan <jhogan@kernel.org>
2018-01-18MIPS: ingenic: Use common cmdline handling codePaul Burton
jz4740_init_cmdline appends all arguments from argv (in fw_arg1) to arcs_cmdline, up to argc (in fw_arg0). The common code in fw_init_cmdline will do the exact same thing when run on a system where fw_arg0 isn't a pointer to kseg0 (it'll also set _fw_envp but we don't use it). Remove the custom implementation & use the generic code. Signed-off-by: Paul Burton <paul.burton@mips.com> Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com> Reviewed-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Maarten ter Huurne <maarten@treewalker.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/18484/ Signed-off-by: James Hogan <jhogan@kernel.org>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-22MIPS: jz4740: Remove custom GPIO codePaul Cercueil
All the drivers for the various hardware elements of the jz4740 SoC have been modified to use the pinctrl framework for their pin configuration needs. As such, this platform code is now unused and can be deleted. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-22MIPS: JZ4740: Qi LB60: Add pinctrl configuration for several driversPaul Cercueil
We set the pin configuration for the jz4740-nand, jz4740-mmc, jz4740-fb, jz4740-pwm and jz4740-uart drivers. This will permit those drivers to be cleaned out of the custom GPIO code that they currently use. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-04-14MIPS: clockevent drivers: Set ->min_delta_ticks and ->max_delta_ticksNicolai Stange
In preparation for making the clockevents core NTP correction aware, all clockevent device drivers must set ->min_delta_ticks and ->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a clockevent device's rate is going to change dynamically and thus, the ratio of ns to ticks ceases to stay invariant. Make the MIPS arch's clockevent drivers initialize these fields properly. This patch alone doesn't introduce any change in functionality as the clockevents core still looks exclusively at the (untouched) ->min_delta_ns and ->max_delta_ns. As soon as this has changed, a followup patch will purge the initialization of ->min_delta_ns and ->max_delta_ns from these drivers. Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Keguang Zhang <keguang.zhang@gmail.com> Cc: John Crispin <john@phrozen.org> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: John Stultz <john.stultz@linaro.org>
2017-02-14MIPS: Audit and remove any unnecessary uses of module.hPaul Gortmaker
Historically a lot of these existed because we did not have a distinction between what was modular code and what was providing support to modules via EXPORT_SYMBOL and friends. That changed when we forked out support for the latter into the export.h file. This means we should be able to reduce the usage of module.h in code that is obj-y Makefile or bool Kconfig. In the case of some code where it is modular, we can extend that to also include files that are building basic support functionality but not related to loading or registering the final module; such files also have no need whatsoever for module.h The advantage in removing such instances is that module.h itself sources about 15 other headers; adding significantly to what we feed cpp, and it can obscure what headers we are effectively using. Since module.h might have been the implicit source for init.h (for __init) and for export.h (for EXPORT_SYMBOL) we consider each instance for the presence of either and replace/add as needed. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. Build coverage of all the mips defconfigs revealed the module.h header was masking a couple of implicit include instances, so we add the appropriate headers there. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: David Daney <david.daney@cavium.com> Cc: John Crispin <john@phrozen.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: "Steven J. Hill" <steven.hill@cavium.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15131/ [james.hogan@imgtec.com: Preserve sort order where it already exists] Signed-off-by: James Hogan <james.hogan@imgtec.com>
2016-12-25clocksource: Use a plain u64 instead of cycle_tThomas Gleixner
There is no point in having an extra type for extra confusion. u64 is unambiguous. Conversion was done with the following coccinelle script: @rem@ @@ -typedef u64 cycle_t; @fix@ typedef cycle_t; @@ -cycle_t +u64 Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Stultz <john.stultz@linaro.org>
2016-11-05MIPS: jz4740: Remove obsolete codePaul Cercueil
This commit removes two things: - The platform_device that corresponds to the RTC driver, since we now probe this driver from devicetree; - The platform power-off code, since all the jz4740-based platforms are now using the jz4740-rtc driver as the system power controller. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Maarten ter Huurne <maarten@treewalker.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-11-05MIPS: qi_lb60: Probe RTC driver from DT and use it as power controllerPaul Cercueil
Since we already have a devicetree node for the jz4740-rtc driver, we don't have to probe it from platform code. Besides, using the jz4740-rtc driver as the power controller for the qi_lb60 platform allows us to remove the jz4740 platform power-off code, since this is the only jz4740-based board upstream. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Maarten ter Huurne <maarten@treewalker.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>