summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2023-05-28Merge tag 'x86-urgent-2023-05-28' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 cpu fix from Thomas Gleixner: "A single fix for x86: - Prevent a bogus setting for the number of HT siblings, which is caused by the CPUID evaluation trainwreck of X86. That recomputes the value for each CPU, so the last CPU "wins". That can cause completely bogus sibling values" * tag 'x86-urgent-2023-05-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/topology: Fix erroneous smp_num_siblings on Intel Hybrid platforms
2023-05-28Merge tag 'perf-urgent-2023-05-28' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull perf fixes from Thomas Gleixner: "A small set of perf fixes: - Make the MSR-readout based CHA discovery work around broken discovery tables in some SPR firmwares. - Prevent saving PEBS configuration which has software bits set that cause a crash when restored into the relevant MSR" * tag 'perf-urgent-2023-05-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/x86/uncore: Correct the number of CHAs on SPR perf/x86/intel: Save/restore cpuc->active_pebs_data_cfg when using guest PEBS
2023-05-28Merge tag 'objtool-urgent-2023-05-28' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull unwinder fixes from Thomas Gleixner: "A set of unwinder and tooling fixes: - Ensure that the stack pointer on x86 is aligned again so that the unwinder does not read past the end of the stack - Discard .note.gnu.property section which has a pointlessly different alignment than the other note sections. That confuses tooling of all sorts including readelf, libbpf and pahole" * tag 'objtool-urgent-2023-05-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/show_trace_log_lvl: Ensure stack pointer is aligned, again vmlinux.lds.h: Discard .note.gnu.property section
2023-05-28Merge tag 'mips-fixes_6.4_1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS fixes from Thomas Bogendoerfer: - fixes to get alchemy platform back in shape - fix for initrd detection * tag 'mips-fixes_6.4_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: mips: Move initrd_start check after initrd address sanitisation. MIPS: Alchemy: fix dbdma2 MIPS: Restore Au1300 support MIPS: unhide PATA_PLATFORM
2023-05-27Merge tag 'powerpc-6.4-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fix from Michael Ellerman: - Reinstate ARCH_FORCE_MAX_ORDER ranges to fix various breakage * tag 'powerpc-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/mm: Reinstate ARCH_FORCE_MAX_ORDER ranges
2023-05-27Merge tag 'for-linus-6.4-rc4-tag' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: - a double free fix in the Xen pvcalls backend driver - a fix for a regression causing the MSI related sysfs entries to not being created in Xen PV guests - a fix in the Xen blkfront driver for handling insane input data better * tag 'for-linus-6.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: x86/pci/xen: populate MSI sysfs entries xen/pvcalls-back: fix double frees with pvcalls_new_active_socket() xen/blkfront: Only check REQ_FUA for writes
2023-05-26Merge tag 'arm-fixes-6.4-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "There have not been a lot of fixes for for the soc tree in 6.4, but these have been sitting here for too long. For the devicetree side, there is one minor warning fix for vexpress, the rest all all for the the NXP i.MX platforms: SoC specific bugfixes for the iMX8 clocks and its USB-3.0 gadget device, as well as board specific fixes for regulators and the phy on some of the i.MX boards. The microchip risc-v and arm32 maintainers now also add a shared maintainer file entry for the arm64 parts. The remaining fixes are all for firmware drivers, addressing mistakes in the optee, scmi and ff-a firmware driver implementation, mostly in the error handling code, incorrect use of the alloc_workqueue() interface in SCMI, and compatibility with corner cases of the firmware implementation" * tag 'arm-fixes-6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: MAINTAINERS: update arm64 Microchip entries arm64: dts: imx8: fix USB 3.0 Gadget Failure in QM & QXPB0 at super speed dt-binding: cdns,usb3: Fix cdns,on-chip-buff-size type arm64: dts: colibri-imx8x: delete adc1 and dsp arm64: dts: colibri-imx8x: fix iris pinctrl configuration arm64: dts: colibri-imx8x: move pinctrl property from SoM to eval board arm64: dts: colibri-imx8x: fix eval board pin configuration arm64: dts: imx8mp: Fix video clock parents ARM: dts: imx6qdl-mba6: Add missing pvcie-supply regulator ARM: dts: imx6ull-dhcor: Set and limit the mode for PMIC buck 1, 2 and 3 arm64: dts: imx8mn-var-som: fix PHY detection bug by adding deassert delay arm64: dts: imx8mn: Fix video clock parents firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors firmware: arm_ffa: Fix FFA device names for logical partitions firmware: arm_ffa: Fix usage of partition info get count flag firmware: arm_ffa: Check if ffa_driver remove is present before executing arm64: dts: arm: add missing cache properties ARM: dts: vexpress: add missing cache properties firmware: arm_scmi: Fix incorrect alloc_workqueue() invocation optee: fix uninited async notif value
2023-05-26x86: re-introduce support for ERMS copies for user space accessesLinus Torvalds
I tried to streamline our user memory copy code fairly aggressively in commit adfcf4231b8c ("x86: don't use REP_GOOD or ERMS for user memory copies"), in order to then be able to clean up the code and inline the modern FSRM case in commit 577e6a7fd50d ("x86: inline the 'rep movs' in user copies for the FSRM case"). We had reports [1] of that causing regressions earlier with blogbench, but that turned out to be a horrible benchmark for that case, and not a sufficient reason for re-instating "rep movsb" on older machines. However, now Eric Dumazet reported [2] a regression in performance that seems to be a rather more real benchmark, where due to the removal of "rep movs" a TCP stream over a 100Gbps network no longer reaches line speed. And it turns out that with the simplified the calling convention for the non-FSRM case in commit 427fda2c8a49 ("x86: improve on the non-rep 'copy_user' function"), re-introducing the ERMS case is actually fairly simple. Of course, that "fairly simple" is glossing over several missteps due to having to fight our assembler alternative code. This code really wanted to rewrite a conditional branch to have two different targets, but that made objtool sufficiently unhappy that this instead just ended up doing a choice between "jump to the unrolled loop, or use 'rep movsb' directly". Let's see if somebody finds a case where the kernel memory copies also care (see commit 68674f94ffc9: "x86: don't use REP_GOOD or ERMS for small memory copies"). But Eric does argue that the user copies are special because networking tries to copy up to 32KB at a time, if order-3 pages allocations are possible. In-kernel memory copies are typically small, unless they are the special "copy pages at a time" kind that still use "rep movs". Link: https://lore.kernel.org/lkml/202305041446.71d46724-yujie.liu@intel.com/ [1] Link: https://lore.kernel.org/lkml/CANn89iKUbyrJ=r2+_kK+sb2ZSSHifFZ7QkPLDpAtkJ8v4WUumA@mail.gmail.com/ [2] Reported-and-tested-by: Eric Dumazet <edumazet@google.com> Fixes: adfcf4231b8c ("x86: don't use REP_GOOD or ERMS for user memory copies") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2023-05-25Merge tag 'parisc-for-6.4-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux Pull parisc architecture fixes from Helge Deller: "Quite a bunch of real bugfixes in here and most of them are tagged for backporting: A fix for cache flushing from irq context, a kprobes & kgdb breakpoint handling fix, and a fix in the alternative code patching function to take care of CPU hotplugging. parisc now provides LOCKDEP support and comes with a lightweight spinlock check. Both features helped me to find the cache flush bug. Additionally writing the AGP gatt has been fixed, the machine allows the user to reboot after a system halt and arch_sync_dma_for_cpu() has been optimized for PCXL PCUs. Summary: - Fix flush_dcache_page() for usage from irq context - Handle kprobes breakpoints only in kernel context - Handle kgdb breakpoints only in kernel context - Use num_present_cpus() in alternative patching code - Enable LOCKDEP support - Add lightweight spinlock checks - Flush AGP gatt writes and adjust gatt mask in parisc_agp_mask_memory() - Allow to reboot machine after system halt - Improve cache flushing for PCXL in arch_sync_dma_for_cpu()" * tag 'parisc-for-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: Fix flush_dcache_page() for usage from irq context parisc: Handle kgdb breakpoints only in kernel context parisc: Handle kprobes breakpoints only in kernel context parisc: Allow to reboot machine after system halt parisc: Enable LOCKDEP support parisc: Add lightweight spinlock checks parisc: Use num_present_cpus() in alternative patching code parisc: Flush gatt writes and adjust gatt mask in parisc_agp_mask_memory() parisc: Improve cache flushing for PCXL in arch_sync_dma_for_cpu()
2023-05-25x86/topology: Fix erroneous smp_num_siblings on Intel Hybrid platformsZhang Rui
Traditionally, all CPUs in a system have identical numbers of SMT siblings. That changes with hybrid processors where some logical CPUs have a sibling and others have none. Today, the CPU boot code sets the global variable smp_num_siblings when every CPU thread is brought up. The last thread to boot will overwrite it with the number of siblings of *that* thread. That last thread to boot will "win". If the thread is a Pcore, smp_num_siblings == 2. If it is an Ecore, smp_num_siblings == 1. smp_num_siblings describes if the *system* supports SMT. It should specify the maximum number of SMT threads among all cores. Ensure that smp_num_siblings represents the system-wide maximum number of siblings by always increasing its value. Never allow it to decrease. On MeteorLake-P platform, this fixes a problem that the Ecore CPUs are not updated in any cpu sibling map because the system is treated as an UP system when probing Ecore CPUs. Below shows part of the CPU topology information before and after the fix, for both Pcore and Ecore CPU (cpu0 is Pcore, cpu 12 is Ecore). ... -/sys/devices/system/cpu/cpu0/topology/package_cpus:000fff -/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-11 +/sys/devices/system/cpu/cpu0/topology/package_cpus:3fffff +/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-21 ... -/sys/devices/system/cpu/cpu12/topology/package_cpus:001000 -/sys/devices/system/cpu/cpu12/topology/package_cpus_list:12 +/sys/devices/system/cpu/cpu12/topology/package_cpus:3fffff +/sys/devices/system/cpu/cpu12/topology/package_cpus_list:0-21 Notice that the "before" 'package_cpus_list' has only one CPU. This means that userspace tools like lscpu will see a little laptop like an 11-socket system: -Core(s) per socket: 1 -Socket(s): 11 +Core(s) per socket: 16 +Socket(s): 1 This is also expected to make the scheduler do rather wonky things too. [ dhansen: remove CPUID detail from changelog, add end user effects ] CC: stable@kernel.org Fixes: bbb65d2d365e ("x86: use cpuid vector 0xb when available for detecting cpu topology") Fixes: 95f3d39ccf7a ("x86/cpu/topology: Provide detect_extended_topology_early()") Suggested-by: Len Brown <len.brown@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/all/20230323015640.27906-1-rui.zhang%40intel.com
2023-05-25Merge tag 'm68k-for-v6.4-tag2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k Pull m68k fix from Geert Uytterhoeven: - Fix signal frame issue causing user-space crashes on 68020/68030 * tag 'm68k-for-v6.4-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: m68k: Move signal frame following exception on 68020/030
2023-05-25Merge tag 'imx-fixes-6.4' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 6.4: - A couple of i.MX8MN/P video clock changes from Adam Ford to fix issue with clock re-parenting. - Add missing pvcie-supply regulator for imx6qdl-mba6 board. - A series of colibri-imx8x board fixes on pin configuration. - Set and limit the mode for PMIC bucks for imx6ull-dhcor board to fix stability problems. - A couple of changes from Frank Li to correct cdns,usb3 bindings cdns,on-chip-buff-size property and fix USB 3.0 gadget failure on i.MX8QM & QXPB0. - Add a required PHY deassert delay for imx8mn-var-som board to fix PHY detection failure. * tag 'imx-fixes-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: arm64: dts: imx8: fix USB 3.0 Gadget Failure in QM & QXPB0 at super speed dt-binding: cdns,usb3: Fix cdns,on-chip-buff-size type arm64: dts: colibri-imx8x: delete adc1 and dsp arm64: dts: colibri-imx8x: fix iris pinctrl configuration arm64: dts: colibri-imx8x: move pinctrl property from SoM to eval board arm64: dts: colibri-imx8x: fix eval board pin configuration arm64: dts: imx8mp: Fix video clock parents ARM: dts: imx6qdl-mba6: Add missing pvcie-supply regulator ARM: dts: imx6ull-dhcor: Set and limit the mode for PMIC buck 1, 2 and 3 arm64: dts: imx8mn-var-som: fix PHY detection bug by adding deassert delay arm64: dts: imx8mn: Fix video clock parents Link: https://lore.kernel.org/r/20230516133625.GI767028@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2023-05-25Merge tag 'juno-fixes-6.4' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes Arm FVP/Vexpress fixes for v6.4 Couple of fixes to address the missing required 'cache-unified' property in the level 2 and 3 caches on some of the FVP/vexpress platforms. * tag 'juno-fixes-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: arm64: dts: arm: add missing cache properties ARM: dts: vexpress: add missing cache properties Link: https://lore.kernel.org/r/20230509143508.1188786-1-sudeep.holla@arm.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2023-05-24perf/x86/uncore: Correct the number of CHAs on SPRKan Liang
The number of CHAs from the discovery table on some SPR variants is incorrect, because of a firmware issue. An accurate number can be read from the MSR UNC_CBO_CONFIG. Fixes: 949b11381f81 ("perf/x86/intel/uncore: Add Sapphire Rapids server CHA support") Reported-by: Stephane Eranian <eranian@google.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Stephane Eranian <eranian@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230508140206.283708-1-kan.liang@linux.intel.com
2023-05-24parisc: Fix flush_dcache_page() for usage from irq contextHelge Deller
Since at least kernel 6.1, flush_dcache_page() is called with IRQs disabled, e.g. from aio_complete(). But the current implementation for flush_dcache_page() on parisc unintentionally re-enables IRQs, which may lead to deadlocks. Fix it by using xa_lock_irqsave() and xa_unlock_irqrestore() for the flush_dcache_mmap_*lock() macros instead. Cc: linux-parisc@vger.kernel.org Cc: stable@kernel.org # 5.18+ Signed-off-by: Helge Deller <deller@gmx.de>
2023-05-24x86/pci/xen: populate MSI sysfs entriesMaximilian Heyne
Commit bf5e758f02fc ("genirq/msi: Simplify sysfs handling") reworked the creation of sysfs entries for MSI IRQs. The creation used to be in msi_domain_alloc_irqs_descs_locked after calling ops->domain_alloc_irqs. Then it moved into __msi_domain_alloc_irqs which is an implementation of domain_alloc_irqs. However, Xen comes with the only other implementation of domain_alloc_irqs and hence doesn't run the sysfs population code anymore. Commit 6c796996ee70 ("x86/pci/xen: Fixup fallout from the PCI/MSI overhaul") set the flag MSI_FLAG_DEV_SYSFS for the xen msi_domain_info but that doesn't actually have an effect because Xen uses it's own domain_alloc_irqs implementation. Fix this by making use of the fallback functions for sysfs population. Fixes: bf5e758f02fc ("genirq/msi: Simplify sysfs handling") Signed-off-by: Maximilian Heyne <mheyne@amazon.de> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20230503131656.15928-1-mheyne@amazon.de Signed-off-by: Juergen Gross <jgross@suse.com>
2023-05-24parisc: Handle kgdb breakpoints only in kernel contextHelge Deller
The kernel kgdb break instructions should only be handled when running in kernel context. Cc: <stable@vger.kernel.org> # v5.4+ Signed-off-by: Helge Deller <deller@gmx.de>
2023-05-24parisc: Handle kprobes breakpoints only in kernel contextHelge Deller
The kernel kprobes break instructions should only be handled when running in kernel context. Cc: <stable@vger.kernel.org> # v5.18+ Signed-off-by: Helge Deller <deller@gmx.de>
2023-05-24parisc: Allow to reboot machine after system haltHelge Deller
In case a machine can't power-off itself on system shutdown, allow the user to reboot it by pressing the RETURN key. Cc: <stable@vger.kernel.org> # v4.14+ Signed-off-by: Helge Deller <deller@gmx.de>
2023-05-24parisc: Enable LOCKDEP supportHelge Deller
Cc: <stable@vger.kernel.org> # v6.0+ Signed-off-by: Helge Deller <deller@gmx.de>
2023-05-24parisc: Add lightweight spinlock checksHelge Deller
Add a lightweight spinlock check which uses only two instructions per spinlock call. It detects if a spinlock has been trashed by some memory corruption and then halts the kernel. It will not detect uninitialized spinlocks, for which CONFIG_DEBUG_SPINLOCK needs to be enabled. This lightweight spinlock check shouldn't influence runtime, so it's safe to enable it by default. The __ARCH_SPIN_LOCK_UNLOCKED_VAL constant has been choosen small enough to be able to be loaded by one LDI assembler statement. Signed-off-by: Helge Deller <deller@gmx.de>
2023-05-23Merge tag 'xtensa-20230523' of https://github.com/jcmvbkbc/linux-xtensaLinus Torvalds
Pull Xtensa fixes from Max Filippov: - fix signal delivery to FDPIC process - add __bswap{si,di}2 helpers * tag 'xtensa-20230523' of https://github.com/jcmvbkbc/linux-xtensa: xtensa: add __bswap{si,di}2 helpers xtensa: fix signal delivery to FDPIC process
2023-05-23parisc: Use num_present_cpus() in alternative patching codeHelge Deller
When patching the kernel code some alternatives depend on SMP vs. !SMP. Use the value of num_present_cpus() instead of num_online_cpus() to decide, otherwise we may run into issues if and additional CPU is enabled after having loaded a module while only one CPU was enabled. Signed-off-by: Helge Deller <deller@gmx.de> Cc: <stable@vger.kernel.org> # v6.1+
2023-05-23mips: Move initrd_start check after initrd address sanitisation.Liviu Dudau
PAGE_OFFSET is technically a virtual address so when checking the value of initrd_start against it we should make sure that it has been sanitised from the values passed by the bootloader. Without this change, even with a bootloader that passes correct addresses for an initrd, we are failing to load it on MT7621 boards, for example. Signed-off-by: Liviu Dudau <liviu@dudau.co.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-05-23MIPS: Alchemy: fix dbdma2Manuel Lauss
Various fixes for the Au1200/Au1550/Au1300 DBDMA2 code: - skip cache invalidation if chip has working coherency circuitry. - invalidate KSEG0-portion of the (physical) data address. - force the dma channel doorbell write out to bus immediately with a sync. Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-05-23MIPS: Restore Au1300 supportManuel Lauss
The Au1300, at least the one I have to test, uses the NetLogic vendor ID, but commit 95b8a5e0111a ("MIPS: Remove NETLOGIC support") also dropped Au1300 detection. Restore Au1300 detection. Tested on DB1300 with Au1380 chip. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-05-23MIPS: unhide PATA_PLATFORMManuel Lauss
Alchemy DB1200/DB1300 boards can use the pata_platform driver. Unhide the config entry in all of MIPS. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-05-23perf/x86/intel: Save/restore cpuc->active_pebs_data_cfg when using guest PEBSLike Xu
After commit b752ea0c28e3 ("perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG"), the cpuc->pebs_data_cfg may save some bits that are not supported by real hardware, such as PEBS_UPDATE_DS_SW. This would cause the VMX hardware MSR switching mechanism to save/restore invalid values for PEBS_DATA_CFG MSR, thus crashing the host when PEBS is used for guest. Fix it by using the active host value from cpuc->active_pebs_data_cfg. Fixes: b752ea0c28e3 ("perf/x86/intel/ds: Flush PEBS DS when changing PEBS_DATA_CFG") Signed-off-by: Like Xu <likexu@tencent.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Link: https://lore.kernel.org/r/20230517133808.67885-1-likexu@tencent.com
2023-05-22Merge tag 'x86_urgent_for_6.4-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fix from Dave Hansen: "This works around and issue where the INVLPG instruction may miss invalidating kernel TLB entries in recent hybrid CPUs. I do expect an eventual microcode fix for this. When the microcode version numbers are known, we can circle back around and add them the model table to disable this workaround" * tag 'x86_urgent_for_6.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/mm: Avoid incomplete Global INVLPG flushes
2023-05-22parisc: Improve cache flushing for PCXL in arch_sync_dma_for_cpu()Helge Deller
Add comment in arch_sync_dma_for_device() and handle the direction flag in arch_sync_dma_for_cpu(). When receiving data from the device (DMA_FROM_DEVICE) unconditionally purge the data cache in arch_sync_dma_for_cpu(). Signed-off-by: Helge Deller <deller@gmx.de>
2023-05-22m68k: Move signal frame following exception on 68020/030Finn Thain
On 68030/020, an instruction such as, moveml %a2-%a3/%a5,%sp@- may cause a stack page fault during instruction execution (i.e. not at an instruction boundary) and produce a format 0xB exception frame. In this situation, the value of USP will be unreliable. If a signal is to be delivered following the exception, this USP value is used to calculate the location for a signal frame. This can result in a corrupted user stack. The corruption was detected in dash (actually in glibc) where it showed up as an intermittent "stack smashing detected" message and crash following signal delivery for SIGCHLD. It was hard to reproduce that failure because delivery of the signal raced with the page fault and because the kernel places an unpredictable gap of up to 7 bytes between the USP and the signal frame. A format 0xB exception frame can be produced by a bus error or an address error. The 68030 Users Manual says that address errors occur immediately upon detection during instruction prefetch. The instruction pipeline allows prefetch to overlap with other instructions, which means an address error can arise during the execution of a different instruction. So it seems likely that this patch may help in the address error case also. Reported-and-tested-by: Stan Johnson <userm57@yahoo.com> Link: https://lore.kernel.org/all/CAMuHMdW3yD22_ApemzW_6me3adq6A458u1_F0v-1EYwK_62jPA@mail.gmail.com/ Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: Andreas Schwab <schwab@linux-m68k.org> Cc: stable@vger.kernel.org Co-developed-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@linux-m68k.org> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Link: https://lore.kernel.org/r/9e66262a754fcba50208aa424188896cc52a1dd1.1683365892.git.fthain@linux-m68k.org Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2023-05-21Merge tag 'uml-for-linus-6.4-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux Pull UML fix from Richard Weinberger: - Fix modular build for UML watchdog * tag 'uml-for-linus-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux: um: harddog: fix modular build
2023-05-21Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds
Pull kvm fixes from Paolo Bonzini: "ARM: - Plug a race in the stage-2 mapping code where the IPA and the PA would end up being out of sync - Make better use of the bitmap API (bitmap_zero, bitmap_zalloc...) - FP/SVE/SME documentation update, in the hope that this field becomes clearer... - Add workaround for Apple SEIS brokenness to a new SoC - Random comment fixes x86: - add MSR_IA32_TSX_CTRL into msrs_to_save - fixes for XCR0 handling in SGX enclaves Generic: - Fix vcpu_array[0] races - Fix race between starting a VM and 'reboot -f'" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: VMX: add MSR_IA32_TSX_CTRL into msrs_to_save KVM: x86: Don't adjust guest's CPUID.0x12.1 (allowed SGX enclave XFRM) KVM: VMX: Don't rely _only_ on CPUID to enforce XCR0 restrictions for ECREATE KVM: Fix vcpu_array[0] races KVM: VMX: Fix header file dependency of asm/vmx.h KVM: Don't enable hardware after a restart/shutdown is initiated KVM: Use syscore_ops instead of reboot_notifier to hook restart/shutdown KVM: arm64: vgic: Add Apple M2 PRO/MAX cpus to the list of broken SEIS implementations KVM: arm64: Clarify host SME state management KVM: arm64: Restructure check for SVE support in FP trap handler KVM: arm64: Document check for TIF_FOREIGN_FPSTATE KVM: arm64: Fix repeated words in comments KVM: arm64: Constify start/end/phys fields of the pgtable walker data KVM: arm64: Infer PA offset from VA in hyp map walker KVM: arm64: Infer the PA offset from IPA in stage-2 map walker KVM: arm64: Use the bitmap API to allocate bitmaps KVM: arm64: Slightly optimize flush_context()
2023-05-21Merge tag 'powerpc-6.4-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: - Fix broken soft dirty tracking when using the Radix MMU (>= P9) - Fix ISA mapping when "ranges" property is not present, for PASemi Nemo boards - Fix a possible WARN_ON_ONCE hitting in BPF extable handling - Fix incorrect DMA address handling when using 2MB TCEs - Fix a bug in IOMMU table handling for SR-IOV devices - Fix the recent rework of IOMMU handling which left arch code calling clean up routines that are handled by the IOMMU core - A few assorted build fixes Thanks to Christian Zigotzky, Dan Horák, Gaurav Batra, Hari Bathini, Jason Gunthorpe, Nathan Chancellor, Naveen N. Rao, Nicholas Piggin, Pali Rohár, Randy Dunlap, and Rob Herring. * tag 'powerpc-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/iommu: Incorrect DDW Table is referenced for SR-IOV device powerpc/iommu: DMA address offset is incorrectly calculated with 2MB TCEs powerpc/iommu: Remove iommu_del_device() powerpc/crypto: Fix aes-gcm-p10 build when VSX=n powerpc/bpf: populate extable entries only during the last pass powerpc/boot: Disable power10 features after BOOTAFLAGS assignment powerpc/64s/radix: Fix soft dirty tracking powerpc/fsl_uli1575: fix kconfig warnings and build errors powerpc/isa-bridge: Fix ISA mapping when "ranges" is not present
2023-05-21KVM: VMX: add MSR_IA32_TSX_CTRL into msrs_to_saveMingwei Zhang
Add MSR_IA32_TSX_CTRL into msrs_to_save[] to explicitly tell userspace to save/restore the register value during migration. Missing this may cause userspace that relies on KVM ioctl(KVM_GET_MSR_INDEX_LIST) fail to port the value to the target VM. In addition, there is no need to add MSR_IA32_TSX_CTRL when ARCH_CAP_TSX_CTRL_MSR is not supported in kvm_get_arch_capabilities(). So add the checking in kvm_probe_msr_to_save(). Fixes: c11f83e0626b ("KVM: vmx: implement MSR_IA32_TSX_CTRL disable RTM functionality") Reported-by: Jim Mattson <jmattson@google.com> Signed-off-by: Mingwei Zhang <mizhang@google.com> Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com> Reviewed-by: Jim Mattson <jmattson@google.com> Message-Id: <20230509032348.1153070-1-mizhang@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2023-05-21KVM: x86: Don't adjust guest's CPUID.0x12.1 (allowed SGX enclave XFRM)Sean Christopherson
Drop KVM's manipulation of guest's CPUID.0x12.1 ECX and EDX, i.e. the allowed XFRM of SGX enclaves, now that KVM explicitly checks the guest's allowed XCR0 when emulating ECREATE. Note, this could theoretically break a setup where userspace advertises a "bad" XFRM and relies on KVM to provide a sane CPUID model, but QEMU is the only known user of KVM SGX, and QEMU explicitly sets the SGX CPUID XFRM subleaf based on the guest's XCR0. Reviewed-by: Kai Huang <kai.huang@intel.com> Tested-by: Kai Huang <kai.huang@intel.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Message-Id: <20230503160838.3412617-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2023-05-21KVM: VMX: Don't rely _only_ on CPUID to enforce XCR0 restrictions for ECREATESean Christopherson
Explicitly check the vCPU's supported XCR0 when determining whether or not the XFRM for ECREATE is valid. Checking CPUID works because KVM updates guest CPUID.0x12.1 to restrict the leaf to a subset of the guest's allowed XCR0, but that is rather subtle and KVM should not modify guest CPUID except for modeling true runtime behavior (allowed XFRM is most definitely not "runtime" behavior). Reviewed-by: Kai Huang <kai.huang@intel.com> Tested-by: Kai Huang <kai.huang@intel.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Message-Id: <20230503160838.3412617-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2023-05-21powerpc/mm: Reinstate ARCH_FORCE_MAX_ORDER rangesMichael Ellerman
Commit 1e8fed873e74 ("powerpc: drop ranges for definition of ARCH_FORCE_MAX_ORDER") removed the limits on the possible values for ARCH_FORCE_MAX_ORDER. However removing the ranges entirely causes some common work flows to break. For example building a defconfig (which uses 64K pages), changing the page size to 4K, and rebuilding used to work, because ARCH_FORCE_MAX_ORDER would be clamped to 12 by the ranges. With the ranges removed it creates a kernel that builds but crashes at boot: kernel BUG at mm/huge_memory.c:470! Oops: Exception in kernel mode, sig: 5 [#1] ... NIP hugepage_init+0x9c/0x278 LR do_one_initcall+0x80/0x320 Call Trace: do_one_initcall+0x80/0x320 kernel_init_freeable+0x304/0x3ac kernel_init+0x30/0x1a0 ret_from_kernel_user_thread+0x14/0x1c The reasoning for removing the ranges was that some of the values were too large. So take that into account and limit the maximums to 10 which is the default max, except for the 4K case which uses 12. Fixes: 1e8fed873e74 ("powerpc: drop ranges for definition of ARCH_FORCE_MAX_ORDER") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230519113806.370635-1-mpe@ellerman.id.au
2023-05-19Merge tag 's390-6.4-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Alexander Gordeev: - Add check whether the required facilities are installed before using the s390-specific ChaCha20 implementation - Key blobs for s390 protected key interface IOCTLs commands PKEY_VERIFYKEY2 and PKEY_VERIFYKEY3 may contain clear key material. Zeroize copies of these keys in kernel memory after creating protected keys - Set CONFIG_INIT_STACK_NONE=y in defconfigs to avoid extra overhead of initializing all stack variables by default - Make sure that when a new channel-path is enabled all subchannels are evaluated: with and without any devices connected on it - When SMT thread CPUs are added to CPU topology masks the nr_cpu_ids limit is not checked and could be exceeded. Respect the nr_cpu_ids limit and avoid a warning when CONFIG_DEBUG_PER_CPU_MAPS is set - The pointer to IPL Parameter Information Block is stored in the absolute lowcore as a virtual address. Save it as the physical address for later use by dump tools - Fix a Queued Direct I/O (QDIO) problem on z/VM guests using QIOASSIST with dedicated (pass through) QDIO-based devices such as FCP, real OSA or HiperSockets - s390's struct statfs and struct statfs64 contain padding, which field-by-field copying does not set. Initialize the respective structures with zeros before filling them and copying to userspace - Grow s390 compat_statfs64, statfs and statfs64 structures f_spare array member to cover padding and simplify things - Remove obsolete SCHED_BOOK and SCHED_DRAWER configs - Remove unneeded S390_CCW_IOMMU and S390_AP_IOM configs * tag 's390-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/iommu: get rid of S390_CCW_IOMMU and S390_AP_IOMMU s390/Kconfig: remove obsolete configs SCHED_{BOOK,DRAWER} s390/uapi: cover statfs padding by growing f_spare statfs: enforce statfs[64] structure initialization s390/qdio: fix do_sqbs() inline assembly constraint s390/ipl: fix IPIB virtual vs physical address confusion s390/topology: honour nr_cpu_ids when adding CPUs s390/cio: include subchannels without devices also for evaluation s390/defconfigs: set CONFIG_INIT_STACK_NONE=y s390/pkey: zeroize key blobs s390/crypto: use vector instructions only if available for ChaCha20
2023-05-19Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Will Deacon: "A mixture of compiler/static checker resolutions and a couple of MTE fixes: - Avoid erroneously marking untagged pages with PG_mte_tagged - Always reset KASAN tags for destination page in copy_page() - Mark PMU header functions 'static inline' - Fix some sparse warnings due to missing casts" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: mte: Do not set PG_mte_tagged if tags were not initialized arm64: Also reset KASAN tag if page is not PG_mte_tagged arm64: perf: Mark all accessor functions inline ARM: perf: Mark all accessor functions inline arm64: vdso: Pass (void *) to virt_to_page() arm64/mm: mark private VM_FAULT_X defines as vm_fault_t
2023-05-19KVM: VMX: Fix header file dependency of asm/vmx.hJacob Xu
Include a definition of WARN_ON_ONCE() before using it. Fixes: bb1fcc70d98f ("KVM: nVMX: Allow L1 to use 5-level page walks for nested EPT") Cc: Sean Christopherson <seanjc@google.com> Signed-off-by: Jacob Xu <jacobhxu@google.com> [reworded commit message; changed <asm/bug.h> to <linux/bug.h>] Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Message-Id: <20220225012959.1554168-1-jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2023-05-18Merge tag 'probes-fixes-v6.4-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace Pull probes fixes from Masami Hiramatsu: - Initialize 'ret' local variables on fprobe_handler() to fix the smatch warning. With this, fprobe function exit handler is not working randomly. - Fix to use preempt_enable/disable_notrace for rethook handler to prevent recursive call of fprobe exit handler (which is based on rethook) - Fix recursive call issue on fprobe_kprobe_handler() - Fix to detect recursive call on fprobe_exit_handler() - Fix to make all arch-dependent rethook code notrace (the arch-independent code is already notrace)" * tag 'probes-fixes-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: rethook, fprobe: do not trace rethook related functions fprobe: add recursion detection in fprobe_exit_handler fprobe: make fprobe_kprobe_handler recursion free rethook: use preempt_{disable, enable}_notrace in rethook_trampoline_handler tracing: fprobe: Initialize ret valiable to fix smatch error
2023-05-18Merge tag 'net-6.4-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Paolo Abeni: "Including fixes from can, xfrm, bluetooth and netfilter. Current release - regressions: - ipv6: fix RCU splat in ipv6_route_seq_show() - wifi: iwlwifi: disable RFI feature Previous releases - regressions: - tcp: fix possible sk_priority leak in tcp_v4_send_reset() - tipc: do not update mtu if msg_max is too small in mtu negotiation - netfilter: fix null deref on element insertion - devlink: change per-devlink netdev notifier to static one - phylink: fix ksettings_set() ethtool call - wifi: mac80211: fortify the spinlock against deadlock by interrupt - wifi: brcmfmac: check for probe() id argument being NULL - eth: ice: - fix undersized tx_flags variable - fix ice VF reset during iavf initialization - eth: hns3: fix sending pfc frames after reset issue Previous releases - always broken: - xfrm: release all offloaded policy memory - nsh: use correct mac_offset to unwind gso skb in nsh_gso_segment() - vsock: avoid to close connected socket after the timeout - dsa: rzn1-a5psw: enable management frames for CPU port - eth: virtio_net: fix error unwinding of XDP initialization - eth: tun: fix memory leak for detached NAPI queue. Misc: - MAINTAINERS: sctp: move Neil to CREDITS" * tag 'net-6.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (107 commits) MAINTAINERS: skip CCing netdev for Bluetooth patches mdio_bus: unhide mdio_bus_init prototype bridge: always declare tunnel functions atm: hide unused procfs functions net: isa: include net/Space.h Revert "ARM: dts: stm32: add CAN support on stm32f746" netfilter: nft_set_rbtree: fix null deref on element insertion netfilter: nf_tables: fix nft_trans type confusion netfilter: conntrack: define variables exp_nat_nla_policy and any_addr with CONFIG_NF_NAT net: wwan: t7xx: Ensure init is completed before system sleep net: selftests: Fix optstring net: pcs: xpcs: fix C73 AN not getting enabled net: wwan: iosm: fix NULL pointer dereference when removing device vlan: fix a potential uninit-value in vlan_dev_hard_start_xmit() mailmap: add entries for Nikolay Aleksandrov igb: fix bit_shift to be in [1..8] range net: dsa: mv88e6xxx: Fix mv88e6393x EPC write command offset cassini: Fix a memory leak in the error handling path of cas_init_one() tun: Fix memory leak for detached NAPI queue. can: kvaser_pciefd: Disable interrupts in probe error path ...
2023-05-18rethook, fprobe: do not trace rethook related functionsZe Gao
These functions are already marked as NOKPROBE to prevent recursion and we have the same reason to blacklist them if rethook is used with fprobe, since they are beyond the recursion-free region ftrace can guard. Link: https://lore.kernel.org/all/20230517034510.15639-5-zegao@tencent.com/ Fixes: f3a112c0c40d ("x86,rethook,kprobes: Replace kretprobe with rethook on x86") Signed-off-by: Ze Gao <zegao@tencent.com> Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2023-05-17Revert "ARM: dts: stm32: add CAN support on stm32f746"Marc Kleine-Budde
This reverts commit 0920ccdf41e3078a4dd2567eb905ea154bc826e6. The commit 0920ccdf41e3 ("ARM: dts: stm32: add CAN support on stm32f746") depends on the patch "dt-bindings: mfd: stm32f7: add binding definition for CAN3" [1], which is not in net/main, yet. This results in a parsing error of "stm32f746.dtsi". So revert this commit. [1] https://lore.kernel.org/all/20230423172528.1398158-2-dario.binacchi@amarulasolutions.com Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com> Cc: Alexandre TORGUE <alexandre.torgue@foss.st.com> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202305172108.x5acbaQG-lkp@intel.com Closes: https://lore.kernel.org/oe-kbuild-all/202305172130.eGGEUhpi-lkp@intel.com Fixes: 0920ccdf41e3 ("ARM: dts: stm32: add CAN support on stm32f746") Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/20230517181950.1106697-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-17Merge tag 'kvmarm-fixes-6.4-1' of ↵Paolo Bonzini
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD KVM/arm64 fixes for 6.4, take #1 - Plug a race in the stage-2 mapping code where the IPA and the PA would end up being out of sync - Make better use of the bitmap API (bitmap_zero, bitmap_zalloc...) - FP/SVE/SME documentation update, in the hope that this field becomes clearer... - Add workaround for the usual Apple SEIS brokenness - Random comment fixes
2023-05-17x86/mm: Avoid incomplete Global INVLPG flushesDave Hansen
The INVLPG instruction is used to invalidate TLB entries for a specified virtual address. When PCIDs are enabled, INVLPG is supposed to invalidate TLB entries for the specified address for both the current PCID *and* Global entries. (Note: Only kernel mappings set Global=1.) Unfortunately, some INVLPG implementations can leave Global translations unflushed when PCIDs are enabled. As a workaround, never enable PCIDs on affected processors. I expect there to eventually be microcode mitigations to replace this software workaround. However, the exact version numbers where that will happen are not known today. Once the version numbers are set in stone, the processor list can be tweaked to only disable PCIDs on affected processors with affected microcode. Note: if anyone wants a quick fix that doesn't require patching, just stick 'nopcid' on your kernel command-line. Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org
2023-05-17s390/iommu: get rid of S390_CCW_IOMMU and S390_AP_IOMMUJason Gunthorpe
These don't do anything anymore, the only user of the symbol was VFIO_CCW/AP which already "depends on VFIO" and VFIO itself selects IOMMU_API. When this was added VFIO was wrongly doing "depends on IOMMU_API" which required some contortions like this to ensure IOMMU_API was turned on. Reviewed-by: Eric Farman <farman@linux.ibm.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Link: https://lore.kernel.org/r/0-v2-eb322ce2e547+188f-rm_iommu_ccw_jgg@nvidia.com Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
2023-05-17s390/Kconfig: remove obsolete configs SCHED_{BOOK,DRAWER}Lukas Bulwahn
Commit f1045056c726 ("topology/sysfs: rework book and drawer topology ifdefery") activates the book and drawer topology, previously activated by CONFIG_SCHED_{BOOK,DRAWER}, dependent on the existence of certain macro definitions. Hence, since then, CONFIG_SCHED_{BOOK,DRAWER} have no effect and any further purpose. Remove the obsolete configs SCHED_{BOOK,DRAWER}. Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20230508040916.16733-1-lukas.bulwahn@gmail.com Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
2023-05-17s390/uapi: cover statfs padding by growing f_spareIlya Leoshkevich
pahole says: struct compat_statfs64 { ... u32 f_spare[4]; /* 68 16 */ /* size: 88, cachelines: 1, members: 12 */ /* padding: 4 */ struct statfs { ... unsigned int f_spare[4]; /* 68 16 */ /* size: 88, cachelines: 1, members: 12 */ /* padding: 4 */ struct statfs64 { ... unsigned int f_spare[4]; /* 68 16 */ /* size: 88, cachelines: 1, members: 12 */ /* padding: 4 */ One has to keep the existence of padding in mind when working with these structs. Grow f_spare arrays to 5 in order to simplify things. Acked-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Link: https://lore.kernel.org/r/20230504144021.808932-3-iii@linux.ibm.com Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
generated by cgit v1.2.3-70-g09d2 (git 2.47.1) at 2024-12-27 01:57:42 +0000