| Age | Commit message (Collapse) | Author |
|---|
|
Currently the maximum number of vCPUs supported is a global value
limited by the used GIC model. GICv3 will lift this limit, but we
still need to observe it for guests using GICv2.
So the maximum number of vCPUs is per-VM value, depending on the
GIC model the guest uses.
Store and check the value in struct kvm_arch, but keep it down to
8 for now.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
With the introduction of a second emulated GIC model we need to let
userspace specify the GIC model to use for each VM. Pass the
userspace provided value down into the vGIC code and store it there
to differentiate later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The virtual MPIDR registers (containing topology information) for the
guest are currently mapped linearily to the vcpu_id. Improve this
mapping for arm64 by using three levels to not artificially limit the
number of vCPUs.
To help this, change and rename the kvm_vcpu_get_mpidr() function to
mask off the non-affinity bits in the MPIDR register.
Also add an accessor to later allow easier access to a vCPU with a
given MPIDR. Use this new accessor in the PSCI emulation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
This patch enables ARMv8 ditry page logging support. Plugs ARMv8 into generic
layer through Kconfig symbol, and drops earlier ARM64 constraints to enable
logging at architecture layer.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
|
|
This patch adds support for arm64 hyp interface to flush all TLBs associated
with VMID.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
|
|
This patch adds arm64 helpers to write protect pmds/ptes and retrieve
permissions while logging dirty pages. Also adds prototype to write protect
a memory slot and adds a pmd define to check for read-only pmds.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
|
|
This patch adds support for 2nd stage page fault handling while dirty page
logging. On huge page faults, huge pages are dissolved to normal pages, and
rebuilding of 2nd stage huge pages is blocked. In case migration is
canceled this restriction is removed and huge pages may be rebuilt again.
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Add support to track dirty pages between user space KVM_GET_DIRTY_LOG ioctl
calls. We call kvm_get_dirty_log_protect() function to do most of the work.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
|
|
Add support for initial write protection of VM memslots. This patch
series assumes that huge PUDs will not be used in 2nd stage tables, which is
always valid on ARMv7
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
|
|
This patch adds ARMv7 architecture TLB Flush function.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
|
|
We now have a generic function that does most of the work of
kvm_vm_ioctl_get_dirty_log, now use it.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
|
|
Currently the trace printk talks about "wfi" only, though the trace
point triggers both on wfi and wfe traps.
Add a parameter to differentiate between the two.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
arm64 uses its own copy of exit handler (arm64/kvm/handle_exit.c).
Currently this file doesn't hook up with any trace points. As a result
users might not see certain events (e.g. HVC & WFI) while using ftrace
with arm64 KVM. This patch fixes this issue by adding a new trace file
and defining two trace events (one of which is shared by wfi and wfe)
for arm64. The new trace points are then linked with related functions
in handle_exit.c.
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Since the advent of VGIC dynamic initialization, this latter is
initialized quite late on the first vcpu run or "on-demand", when
injecting an IRQ or when the guest sets its registers.
This initialization could be initiated explicitly much earlier
by the users-space, as soon as it has provided the requested
dimensioning parameters.
This patch adds a new entry to the VGIC KVM device that allows
the user to manually request the VGIC init:
- a new KVM_DEV_ARM_VGIC_GRP_CTRL group is introduced.
- Its first attribute is KVM_DEV_ARM_VGIC_CTRL_INIT
The rationale behind introducing a group is to be able to add other
controls later on, if needed.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Adds a function kvm_vcpu_set_pending_timer instead of calling
kvm_make_request in lapic.c.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When access to descriptor in LDT/GDT wraparound outside long-mode, the address
of the descriptor should be truncated to 32-bit. Citing Intel SDM 2.1.1.1
"Global and Local Descriptor Tables in IA-32e Mode": "GDTR and LDTR registers
are expanded to 64-bits wide in both IA-32e sub-modes (64-bit mode and
compatibility mode)."
So in other cases, we need to truncate. Creating new function to return a
pointer to descriptor table to avoid too much code duplication.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Wrap 64-bit check with #ifdef CONFIG_X86_64, to avoid a "right shift count
>= width of type" warning and consequent undefined behavior. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When segment is loaded, the segment access bit is set unconditionally. In
fact, it should be set conditionally, based on whether the segment had the
accessed bit set before. In addition, it can improve performance.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
According to Intel SDM: "If the ESP register is used as a base register for
addressing a destination operand in memory, the POP instruction computes the
effective address of the operand after it increments the ESP register."
The current emulation does not behave so. The fix required to waste another
of the precious instruction flags and to check the flag in decode_modrm.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently, if em_call_far fails it returns success instead of the resulting
error-code. Fix it.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The KVM emulator does not emulate JMP and CALL that target a call gate or a
task gate. This patch does not try to implement these scenario as they are
presumably rare; yet it returns X86EMUL_UNHANDLEABLE error in such cases
instead of generating an exception.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Since the operand size of fnstcw and fnstsw is updated during the execution,
the emulation may cause spurious exceptions as it reads the memory beforehand.
Marking these instructions as Mov (since the previous value is ignored) and
DstMem16 to simplify the setting of operand size.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Although pop sreg updates RSP according to the operand size, only 2 bytes are
read. The current behavior may result in incorrect #GP or #PF exceptions.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This makes the direction of the conditions consistent with code that
is already using WARN_ON.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Because ASSERT is just a printk, these would oops right away.
The assertion thus hardly adds anything.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm_init_shadow_ept_mmu
The initialization function in mmu.c can always use walk_mmu, which
is known to be vcpu->arch.mmu. Only init_kvm_nested_mmu is used to
initialize vcpu->arch.nested_mmu.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This is, pedantically, not valid C. It also looks weird.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add tracepoint to wait_lapic_expire.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
[Remind reader if early or late. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
For the hrtimer which emulates the tscdeadline timer in the guest,
add an option to advance expiration, and busy spin on VM-entry waiting
for the actual expiration time to elapse.
This allows achieving low latencies in cyclictest (or any scenario
which requires strict timing regarding timer expiration).
Reduces average cyclictest latency from 12us to 8us
on Core i5 desktop.
Note: this option requires tuning to find the appropriate value
for a particular hardware/guest combination. One method is to measure the
average delay between apic_timer_fn and VM-entry.
Another method is to start with 1000ns, and increase the value
in say 500ns increments until avg cyclictest numbers stop decreasing.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm_x86_ops->test_posted_interrupt() returns true/false depending
whether 'vector' is set.
Next patch makes use of this interface.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In most cases calling hwapic_isr_update(), we always check if
kvm_apic_vid_enabled() == 1, but actually,
kvm_apic_vid_enabled()
-> kvm_x86_ops->vm_has_apicv()
-> vmx_vm_has_apicv() or '0' in svm case
-> return enable_apicv && irqchip_in_kernel(kvm)
So its a little cost to recall vmx_vm_has_apicv() inside
hwapic_isr_update(), here just NULL out hwapic_isr_update() in
case of !enable_apicv inside hardware_setup() then make all
related stuffs follow this. Note we don't check this under that
condition of irqchip_in_kernel() since we should make sure
definitely any caller don't work without in-kernel irqchip.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove FIXME comments about needing fault addresses to be returned. These
are propaagated from walk_addr_generic to gva_to_gpa and from there to
ops->read_std and ops->write_std.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When generating #PF VM-exit, check equality:
(PFEC & PFEC_MASK) == PFEC_MATCH
If there is equality, the 14 bit of exception bitmap is used to take decision
about generating #PF VM-exit. If there is inequality, inverted 14 bit is used.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch improve checks required by Intel Software Developer Manual.
- SMM MSRs are not allowed.
- microcode MSRs are not allowed.
- check x2apic MSRs only when LAPIC is in x2apic mode.
- MSR switch areas must be aligned to 16 bytes.
- address of first and last byte in MSR switch areas should not set any bits
beyond the processor's physical-address width.
Also it adds warning messages on failures during MSR switch. These messages
are useful for people who debug their VMMs in nVMX.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Several hypervisors need MSR auto load/restore feature.
We read MSRs from VM-entry MSR load area which specified by L1,
and load them via kvm_set_msr in the nested entry.
When nested exit occurs, we get MSRs via kvm_get_msr, writing
them to L1`s MSR store area. After this, we read MSRs from VM-exit
MSR load area, and load them via kvm_set_msr.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- Wire up sys_execveat(). Tested on 32 & 64 bit.
- Fix for kdump on LE systems with cpus hot unplugged.
- Revert Anton's fix for "kernel BUG at kernel/smpboot.c:134!", this
broke other platforms, we'll do a proper fix for 3.20.
* tag 'powerpc-3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
Revert "powerpc: Secondary CPUs must set cpu_callin_map after setting active and online"
powerpc/kdump: Ignore failure in enabling big endian exception during crash
powerpc: Wire up sys_execveat() syscall
|
|
See commit 51f39a1f0cea1cacf8c787f652f26dfee9611874
syscalls: implement execveat() system call
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Pull UML fixes from Richard Weinberger:
"Two fixes for UML regressions. Nothing exciting"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
x86, um: actually mark system call tables readonly
um: Skip futex_atomic_cmpxchg_inatomic() test
|
|
Commit 9fc2105aeaaf ("ARM: 7830/1: delay: don't bother reporting
bogomips in /proc/cpuinfo") breaks audio in python, and probably
elsewhere, with message
FATAL: cannot locate cpu MHz in /proc/cpuinfo
I'm not the first one to hit it, see for example
https://theredblacktree.wordpress.com/2014/08/10/fatal-cannot-locate-cpu-mhz-in-proccpuinfo/
https://devtalk.nvidia.com/default/topic/765800/workaround-for-fatal-cannot-locate-cpu-mhz-in-proc-cpuinf/?offset=1
Reading original changelog, I have to say "Stop breaking working setups.
You know who you are!".
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit a074335a370e ("x86, um: Mark system call tables readonly") was
supposed to mark the sys_call_table in UML as RO by adding the const,
but it doesn't have the desired effect as it's nevertheless being placed
into the data section since __cacheline_aligned enforces sys_call_table
being placed into .data..cacheline_aligned instead. We need to use
the ____cacheline_aligned version instead to fix this issue.
Before:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 D sys_call_table
0000000000000000 D syscall_table_size
After:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 R sys_call_table
0000000000000000 D syscall_table_size
Fixes: a074335a370e ("x86, um: Mark system call tables readonly")
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
futex_atomic_cmpxchg_inatomic() does not work on UML because
it triggers a copy_from_user() in kernel context.
On UML copy_from_user() can only be used if the kernel was called
by a real user space process such that UML can use ptrace()
to fetch the value.
Reported-by: Miklos Szeredi <miklos@szeredi.hu>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Daniel Walter <d.walter@0x90.at>
|
|
git://git.rocketboards.org/linux-socfpga-next
Pull arch/nios2 fixes from Ley Foon Tan:
- fix compilation error when enable CONFIG_PREEMPT
- initialize cpuinfo.mmu variable supplied by the device tree
* tag 'nios2-fixes-v3.19-rc3' of git://git.rocketboards.org/linux-socfpga-next:
nios2: Use preempt_schedule_irq
nios2: Initialize cpuinfo.mmu
|
|
Follow aa0d53260596 ("ia64: Use preempt_schedule_irq") and use
preempt_schedule_irq instead of enabling/disabling interrupts and
messing around with PREEMPT_ACTIVE in the nios2 low-level preemption
code ourselves. Also get rid of the now needless re-check for
TIF_NEED_RESCHED, preempt_schedule_irq will already take care of
rescheduling.
This also fixes the following build error when building with
CONFIG_PREEMPT:
arch/nios2/kernel/built-in.o: In function `need_resched':
arch/nios2/kernel/entry.S:374: undefined reference to `PREEMPT_ACTIVE'
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Ley Foon Tan <lftan@altera.com>
|
|
This patch initializes the mmu field of the cpuinfo structure to the
value supplied by the devicetree.
Signed-off-by: Walter Goossens <waltergoossens@home.nl>
Acked-by: Ley Foon Tan <lftan@altera.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A very small set of fixes for 3.19, as everyone was out.
The clocksource patch was something I missed for the merge window
after the change that broke arm64 was merged through arm-soc. The
other two patches are a fix for an undetected merge problem in mvebu
and a defconfig change to make some exynos boards work with the normal
multi_v7_defconfig"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Add USB_EHCI_EXYNOS to multi_v7_defconfig
ARM: mvebu: Fix pinctrl configuration for Armada 370 DB
clocksource: arch_timer: Only use the virtual counter (CNTVCT) on arm64
|
|
Currently we enable Exynos devices in the multi v7 defconfig, however, when
testing on my ODROID-U3, I noticed that USB was not working. Enabling this
option causes USB to work, which enables networking support as well since the
ODROID-U3 has networking on the USB bus.
[arnd] Support for odroid-u3 was added in 3.10, so it would be nice to
backport this fix at least that far.
Signed-off-by: Steev Klimaszewski <steev@gentoo.org>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
and online"
This reverts commit 7c5c92ed56d932b2c19c3f8aea86369509407d33.
Although this did fix the bug it was aimed at, it also broke secondary
startup on platforms that use give/take_timebase(). Unfortunately we
didn't detect that while it was in next.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In LE kernel, we currently have a hack for kexec that resets the exception
endian before starting a new kernel as the kernel that is loaded could be a
big endian or a little endian kernel. In kdump case, resetting exception
endian fails when one or more cpus is disabled. But we can ignore the failure
and still go ahead, as in most cases crashkernel will be of same endianess
as primary kernel and reseting endianess is not even needed in those cases.
This patch adds a new inline function to say if this is kdump path. This
function is used at places where such a check is needed.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
[mpe: Rename to kdump_in_progress(), use bool, and edit comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Wire up sys_execveat(). This passes the selftests for the system call.
Check success of execveat(3, '../execveat', 0)... [OK]
Check success of execveat(5, 'execveat', 0)... [OK]
Check success of execveat(6, 'execveat', 0)... [OK]
Check success of execveat(-100, '/home/pranith/linux/...ftests/exec/execveat', 0)... [OK]
Check success of execveat(99, '/home/pranith/linux/...ftests/exec/execveat', 0)... [OK]
Check success of execveat(8, '', 4096)... [OK]
Check success of execveat(17, '', 4096)... [OK]
Check success of execveat(9, '', 4096)... [OK]
Check success of execveat(14, '', 4096)... [OK]
Check success of execveat(14, '', 4096)... [OK]
Check success of execveat(15, '', 4096)... [OK]
Check failure of execveat(8, '', 0) with ENOENT... [OK]
Check failure of execveat(8, '(null)', 4096) with EFAULT... [OK]
Check success of execveat(5, 'execveat.symlink', 0)... [OK]
Check success of execveat(6, 'execveat.symlink', 0)... [OK]
Check success of execveat(-100, '/home/pranith/linux/...xec/execveat.symlink', 0)... [OK]
Check success of execveat(10, '', 4096)... [OK]
Check success of execveat(10, '', 4352)... [OK]
Check failure of execveat(5, 'execveat.symlink', 256) with ELOOP... [OK]
Check failure of execveat(6, 'execveat.symlink', 256) with ELOOP... [OK]
Check failure of execveat(-100, '/home/pranith/linux/tools/testing/selftests/exec/execveat.symlink', 256) with ELOOP... [OK]
Check success of execveat(3, '../script', 0)... [OK]
Check success of execveat(5, 'script', 0)... [OK]
Check success of execveat(6, 'script', 0)... [OK]
Check success of execveat(-100, '/home/pranith/linux/...elftests/exec/script', 0)... [OK]
Check success of execveat(13, '', 4096)... [OK]
Check success of execveat(13, '', 4352)... [OK]
Check failure of execveat(18, '', 4096) with ENOENT... [OK]
Check failure of execveat(7, 'script', 0) with ENOENT... [OK]
Check success of execveat(16, '', 4096)... [OK]
Check success of execveat(16, '', 4096)... [OK]
Check success of execveat(4, '../script', 0)... [OK]
Check success of execveat(4, 'script', 0)... [OK]
Check success of execveat(4, '../script', 0)... [OK]
Check failure of execveat(4, 'script', 0) with ENOENT... [OK]
Check failure of execveat(5, 'execveat', 65535) with EINVAL... [OK]
Check failure of execveat(5, 'no-such-file', 0) with ENOENT... [OK]
Check failure of execveat(6, 'no-such-file', 0) with ENOENT... [OK]
Check failure of execveat(-100, 'no-such-file', 0) with ENOENT... [OK]
Check failure of execveat(5, '', 4096) with EACCES... [OK]
Check failure of execveat(5, 'Makefile', 0) with EACCES... [OK]
Check failure of execveat(11, '', 4096) with EACCES... [OK]
Check failure of execveat(12, '', 4096) with EACCES... [OK]
Check failure of execveat(99, '', 4096) with EBADF... [OK]
Check failure of execveat(99, 'execveat', 0) with EBADF... [OK]
Check failure of execveat(8, 'execveat', 0) with ENOTDIR... [OK]
Invoke copy of 'execveat' via filename of length 4093:
Check success of execveat(19, '', 4096)... [OK]
Check success of execveat(5, 'xxxxxxxxxxxxxxxxxxxx...yyyyyyyyyyyyyyyyyyyy', 0)... [OK]
Invoke copy of 'script' via filename of length 4093:
Check success of execveat(20, '', 4096)... [OK]
/bin/sh: 0: Can't open /dev/fd/5/xxxxxxx(... a long line of x's and y's, 0)... [OK]
Check success of execveat(5, 'xxxxxxxxxxxxxxxxxxxx...yyyyyyyyyyyyyyyyyyyy', 0)... [OK]
Tested on a 32-bit powerpc system.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Pull KVM fixes from Paolo Bonzini:
"The important fixes are for two bugs introduced by the merge window.
On top of this, add a couple of WARN_ONs and stop spamming dmesg on
pretty much every boot of a virtual machine"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: warn on more invariant breakage
kvm: fix sorting of memslots with base_gfn == 0
kvm: x86: drop severity of "generation wraparound" message
kvm: x86: vmx: reorder some msr writing
|
|
Since most virtual machines raise this message once, it is a bit annoying.
Make it KERN_DEBUG severity.
Cc: stable@vger.kernel.org
Fixes: 7a2e8aaf0f6873b47bc2347f216ea5b0e4c258ab
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
