Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata updates from Niklas Cassel:
- Fix typos in comments (Yan Zhen)
- Remove unused macro definitions (Damien Le Moal)
- Switch back to the .remove() callback (Uwe Kleine-König)
- Make use of the get_unaligned_be24() helper instead of open coding
(Andy Shevchenko)
- Refactor and cleanup ata_scsi_simulate() command emulation, such that
all commands use ata_scsi_rbuf_fill() with its own callback (Damien
Le Moal)
- Improve ata_scsi_simulate() command emulation by accurately setting
the SCSI command residual (number of bytes not filled) in the command
reply (Damien Le Moal)
- Add missing iommus property in ahci-platform device tree binding
(Frank Wunderlich)
* tag 'ata-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
dt-bindings: ata: ahci-platform: add missing iommus property
ata: libata-scsi: Return residual for emulated SCSI commands
ata: libata-scsi: Remove struct ata_scsi_args
ata: libata-scsi: Document all VPD page inquiry actors
ata: libata-scsi: Refactor ata_scsiop_maint_in()
ata: libata-scsi: Refactor ata_scsiop_read_cap()
ata: libata-scsi: Refactor ata_scsi_simulate()
ata: libata-scsi: Refactor scsi_6_lba_len() with use of get_unaligned_be24()
ata: Switch back to struct platform_driver::remove()
ata: libata: Remove unused macro definitions
ata: Fix typos in the comment
|
|
The function ata_scsi_rbuf_fill() used to fill the reply buffer of
emulated SCSI commands always copies the ATA reply buffer
(ata_scsi_rbuf) up to the size of the SCSI command buffer (the transfer
length for the command), even if the reply is shorter than the SCSI
command buffer. This leads to issuers of the SCSI command to always get
a result without any residual (resid is always 0) despite the
potentially shorter reply for the command.
Modify all fill actors used by ata_scsi_rbuf_fill() to return the number
of bytes filled for the reply and 0 in case of error. Using this value,
add a call to scsi_set_resid() in ata_scsi_rbuf_fill() to set the
correct residual for the SCSI command when the reply length is shorter
than the command buffer.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20241022024537.251905-7-dlemoal@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
The data structure struct ata_scsi_args is used to pass the target ATA
device, the SCSI command to simulate and the device identification data
to ata_scsi_rbuf_fill() and to its actor function. This method of
passing information does not improve the code in any way and in fact
increases the number of pointer dereferences for no gains.
Drop this data structure by modifying the interface of
ata_scsi_rbuf_fill() and its actor function to take an ATA device and a
SCSI command as argument.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20241022024537.251905-6-dlemoal@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Add the missing kdoc comments for the ata_scsiop_inq_XX functions used
to emulate access to VPD pages.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20241022024537.251905-5-dlemoal@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Move the check for MI_REPORT_SUPPORTED_OPERATION_CODES from
ata_scsi_simulate() into ata_scsiop_maint_in() to simplify
ata_scsi_simulate() code.
Furthermore, since an rbuff fill actor function returning a non-zero
value causes no data to be returned for the command, directly return
an error (return 1) for invalid command formt after setting the invalid
field in cdb error.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20241022024537.251905-4-dlemoal@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Move the check for the scsi command service action being
SAI_READ_CAPACITY_16 from ata_scsi_simulate() into ata_scsiop_read_cap()
to simplify ata_scsi_simulate() for processing capacity reading commands
(READ_CAPACITY and SERVICE_ACTION_IN_16).
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20241022024537.251905-3-dlemoal@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Factor out the code handling the INQUIRY command in ata_scsi_simulate()
using the function ata_scsi_rbuf_fill() with the new actor
ata_scsiop_inquiry(). This new actor function calls the existing actors
to handle the standard inquiry as well as extended inquiry (VPD page
access).
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20241022024537.251905-2-dlemoal@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Refactor scsi_6_lba_len() with use of get_unaligned_be24() to make it
consistent with other similar helper implementations.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20241016131845.898632-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fixes from Damien Le Moal:
- Fix a NULL pointer dereference introduced by the recent cleanups of
the command duration limits feature handling (me)
- Fix incorrect generation of the mode sense data for the
ALL_SUB_MPAGES page (me)
* tag 'ata-6.12-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-scsi: Fix ata_msense_control() CDL page reporting
ata: libata-scsi: Fix ata_msense_control_spgt2()
|
|
When the user requests the ALL_SUB_MPAGES mode sense page,
ata_msense_control() adds the CDL_T2A_SUB_MPAGE twice instead of adding
the CDL_T2A_SUB_MPAGE and CDL_T2B_SUB_MPAGE pages information. Correct
the second call to ata_msense_control_spgt2() to report the
CDL_T2B_SUB_MPAGE page.
Fixes: 673b2fe6ff1d ("scsi: ata: libata-scsi: Add support for CDL pages mode sense")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
ata_msense_control_spgt2() can be called even for devices that do not
support CDL when the user requests the ALL_SUB_MPAGES mode sense page,
but for such device, this will cause a NULL pointer dereference as
dev->cdl is NULL. Similarly, we should not return any data if
ata_msense_control_spgt2() is called when the user requested the
CDL_T2A_SUB_MPAGE or CDL_T2B_SUB_MPAGE pages for a device that does not
support CDL.
Avoid this potential NULL pointer dereference by checking if the device
support CDL on entry to ata_msense_control_spgt2() and return 0 if it
does not support CDL.
Reported-by: syzbot+37757dc11ee77ef850bb@syzkaller.appspotmail.com
Tested-by: syzbot+37757dc11ee77ef850bb@syzkaller.appspotmail.com
Fixes: 602bcf212637 ("ata: libata: Improve CDL resource management")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata updates from Damien Le Moal:
- Convert the qcom AHCI controller DT bindings to DT schema (from
Rayyan)
- Cleanup of libata core and drivers code handling controller and
device quirks to rename "blacklist" to the more neutral "quirk" and
to replace the rarely used "horkage" term with the more common
"quirk" naming (me)
- Add libata-core message to print the quirks applied to a controller
or device (me)
- Remove the not-so-useful function ata_noop_qc_prep() from libata core
(me)
- ahci_imx driver cleanup, improvements and DT bindings compatible
strings update (Richard and Dan)
- libahci_platform improvements (Zhang)
- Remove obsolete functions declarations from libata header files (from
Gaosheng)
- Improve teh ahci_brcm driver using managed device resources funetions
(Zhang)
- Introduce new helper function to improve libata EH code readability
(Niklas)
- Enable module autoloading for the pata_ftide010, pata_ixp4xx and
sata_gemini drivers (Liao)
- Move SATA related functions and data declaraions from libata-core to
libata-sata (me)
- Rename the function handling the sense data for successful NCQ
commands log to better reflect that function actions (me)
- Reduce libata memory usage by moving port resources to struct
ata_device and by optimizing the management of resources for CDL
capable devices (me)
- Improve libata-eh handling of failed ATA passthrough commands
(Niklas)
* tag 'ata-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux: (39 commits)
ata: libata: Clear DID_TIME_OUT for ATA PT commands with sense data
ata: libata: Fix W=1 compilation warning
ata: libata: Improve CDL resource management
ata: libata: Introduce ata_dev_free_resources
ata: libata: Move sector_buf from struct ata_port to struct ata_device
ata: libata: Rename ata_eh_read_sense_success_ncq_log()
ata: libata: Move sata_std_hardreset() definition to libata-sata.c
ata: libata: Move sata_down_spd_limit() to libata-sata.c
ata: libata: Improve __ata_qc_complete()
ata: libata-scsi: Improve ata_scsi_handle_link_detach()
ata: libata: Cleanup libata-transport
ata: sata_gemini: Enable module autoloading
ata: pata_ixp4xx: Enable module autoloading
ata: pata_ftide010: Enable module autoloading
ata: libata: Add helper ata_eh_decide_disposition()
ata: ahci_brcm: Use devm_platform_ioremap_resource_byname() helper function
ata: libata: Remove obsolete function declarations
ata: ahci_imx: Fix error code in probe()
ata: libahci_platform: Simplify code with for_each_child_of_node_scoped()
ata: ahci_imx: Correct the email address
...
|
|
When ata_qc_complete() schedules a command for EH using
ata_qc_schedule_eh(), blk_abort_request() will be called, which leads to
req->q->mq_ops->timeout() / scsi_timeout() being called.
scsi_timeout(), if the LLDD has no abort handler (libata has no abort
handler), will set host byte to DID_TIME_OUT, and then call
scsi_eh_scmd_add() to add the command to EH.
Thus, when commands first enter libata's EH strategy_handler, all the
commands that have been added to EH will have DID_TIME_OUT set.
libata has its own flag (AC_ERR_TIMEOUT), that it sets for commands that
have not received a completion at the time of entering EH.
Thus, libata doesn't really care about DID_TIME_OUT at all, and currently
clears the host byte at the end of EH, in ata_scsi_qc_complete(), before
scsi_eh_finish_cmd() is called.
However, this clearing in ata_scsi_qc_complete() is currently only done
for commands that are not ATA passthrough commands.
Since the host byte is visible in the completion that we return to user
space for ATA passthrough commands, for ATA passthrough commands that got
completed via EH (commands with sense data), the user will incorrectly see:
ATA pass-through(16): transport error: Host_status=0x03 [DID_TIME_OUT]
Fix this by moving the clearing of the host byte (which is currently only
done for commands that are not ATA passthrough commands) from
ata_scsi_qc_complete() to the start of EH (regardless if the command is
ATA passthrough or not).
While at it, use the proper helper function to clear the host byte, rather
than open coding the clearing.
This will make sure that we:
-Correctly clear DID_TIME_OUT for both ATA passthrough commands and
commands that are not ATA passthrough commands.
-Do not needlessly clear the host byte for commands that did not go via EH.
ata_scsi_qc_complete() is called both for commands that are completed
normally (without going via EH), and for commands that went via EH,
however, only commands that went via EH will have DID_TIME_OUT set.
Fixes: 24aeebbf8ea9 ("scsi: ata: libata: Change ata_eh_request_sense() to not set CHECK_CONDITION")
Reported-by: Igor Pylypiv <ipylypiv@google.com>
Closes: https://lore.kernel.org/linux-ide/ZttIN8He8TOZ7Lct@google.com/
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Tested-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
The ncq_sense_buf buffer field of struct ata_port is allocated and used
only for devices that support the Command Duration Limits (CDL) feature.
However, the cdl buffer of struct ata_device, which is used to cache the
command duration limits log page for devices supporting CDL is always
allocated as part of struct ata_device, which is wasteful of memory for
devices that do not support this feature.
Clean this up by defining both buffers as part of the new ata_cdl
structure and allocating this structure only for devices that support
the CDL feature. This new structure is attached to struct ata_device
using the cdl pointer.
The functions ata_dev_init_cdl_resources() and
ata_dev_cleanup_cdl_resources() are defined to manage this new structure
allocation, initialization and freeing when a port is removed or a
device disabled. ata_dev_init_cdl_resources() is called from
ata_dev_config_cdl() only for devices that support CDL.
ata_dev_cleanup_cdl_resources() is called from ata_dev_free_resources()
to free the ata_cdl structure when a device is being disabled by EH.
Note that the name of the former cdl log buffer of struct ata_device is
changed to desc_log_buf to make it clearer that it is a buffer for the
limit descriptors log page.
This change reduces the size of struct ata_device, thus reducing memory
usage for ATA devices that do not support the CDL feature.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Introduce the function ata_dev_free_resources() to free the resources
allocated to support a device features. For now, this function is
reduced to calling zpodd_exit() for devices that have this feature
enabled.
ata_dev_free_resources() is called from ata_eh_dev_disable() as this
function is always called for all devices attached to a port that is
being detached and for devices that are being disabled due to being
removed (detached) from the system or due to errors.
With this change, the call to zpodd_exit() done in ata_port_detach()
and ata_scsi_handle_link_detach() are removed as these functions
remove all devices attached to the link or port using libata EH, thus
resulting in ata_eh_dev_disable() being called and the zpodd_exit()
function being executed.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
A struct ata_device flags should always be set and cleared with the
device port locked. Testing for a flag should thus also be done while
holding the device port lock. In accordance to this principle, modify
ata_scsi_handle_link_detach() to test and clear the ATA_DFLAG_DETACHED
flag while holding the device port lock.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
This reverts commit 28ab9769117ca944cb6eb537af5599aa436287a4.
Sense data can be in either fixed format or descriptor format.
SAT-6 revision 1, "10.4.6 Control mode page", defines the D_SENSE bit:
"The SATL shall support this bit as defined in SPC-5 with the following
exception: if the D_ SENSE bit is set to zero (i.e., fixed format sense
data), then the SATL should return fixed format sense data for ATA
PASS-THROUGH commands."
The libata SATL has always kept D_SENSE set to zero by default. (It is
however possible to change the value using a MODE SELECT SG_IO command.)
Failed ATA PASS-THROUGH commands correctly respected the D_SENSE bit,
however, successful ATA PASS-THROUGH commands incorrectly returned the
sense data in descriptor format (regardless of the D_SENSE bit).
Commit 28ab9769117c ("ata: libata-scsi: Honor the D_SENSE bit for
CK_COND=1 and no error") fixed this bug for successful ATA PASS-THROUGH
commands.
However, after commit 28ab9769117c ("ata: libata-scsi: Honor the D_SENSE
bit for CK_COND=1 and no error"), there were bug reports that hdparm,
hddtemp, and udisks were no longer working as expected.
These applications incorrectly assume the returned sense data is in
descriptor format, without even looking at the RESPONSE CODE field in the
returned sense data (to see which format the returned sense data is in).
Considering that there will be broken versions of these applications around
roughly forever, we are stuck with being bug compatible with older kernels.
Cc: stable@vger.kernel.org # 4.19+
Reported-by: Stephan Eisvogel <eisvogel@seitics.de>
Reported-by: Christian Heusel <christian@heusel.eu>
Closes: https://lore.kernel.org/linux-ide/0bf3f2f0-0fc6-4ba5-a420-c0874ef82d64@heusel.eu/
Fixes: 28ab9769117c ("ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240813131900.1285842-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
According to Wiktionary, the verb "hork" is computing slang defined as
"To foul up; to be occupied with difficulty, tangle, or unpleasantness;
to be broken" (https://en.wiktionary.org/wiki/hork#Verb). libata uses
this with the term "horkage" to refer to broken device features. Given
that this term is not widely used and its meaning unknown to many,
rename it to the more commonly used term "quirk", similar to many other
places in the kernel.
The renaming done is:
1) Rename all ATA_HORKAGE_XXX flags to ATA_QUIRK_XXX
2) Rename struct ata_device horkage field to quirks
3) Rename struct ata_blacklist_entry to struct ata_dev_quirks_entry. The
array of these structures defining quirks for known devices is
renamed __ata_dev_quirks.
4) The functions ata_dev_blacklisted() and ata_force_horkage() are
renamed to ata_dev_quirks() and ata_force_quirks() respectively.
5) All the force_horkage_xxx() macros are renamed to force_quirk_xxx()
And while at it, make sure that the type "unsigned int" is used
consistantly for quirk flags variables and data structure fields.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata updates from Niklas Cassel:
- ATA PASS-THROUGH sense data cleanups and fixes (Igor Pylypiv)
Store the sense data for ATA PASS-THROUGH commands at the correct
offset in the sense buffer when using fixed format sense data.
Cleanup the logic related to generating sense data for PASS-THROUGH
commands. Generating sense data for PASS-THROUGH commands would
overwrite any eventual (real) sense data received from the device.
Honor the D_SENSE bit when generating sense data for PASS-THROUGH
commands. (The D_SENSE bit can be set by the user, and determines if
the returned sense data should be in fixed format or descriptor
format)
- ata port allocation cleanups (me)
Assign the ata port print_id at port allocation time, such that the
ata_port_* print functions can be used earlier in the init call
chain.
Change the ata port port print_id to use ida_alloc(), such that
print_ids will get reused on rmmod + modprobe, instead of being
incremented indefinitely.
Remove wrappers that only existed in order to export the internal
libata functions which they wrapped, and instead export the libata
functions directly.
- Update SATA_MOBILE_LPM_POLICY Kconfig default to med_power_with_dipm
(Mario Limonciello)
Using this default was not always a good idea before, because it
would break hot plug support. However, with LPM changes in recent
kernels, a port marked as external will not enable LPM (in order to
not break hot plug), so it is now safe to change the default value of
this Kconfig.
All major Linux distros have had SATA_MOBILE_LPM_POLICY set to
med_power_with_dipm for quite a long time
- Convert ahci-fsl-qoriq device tree binding to yaml format (Frank Li)
* tag 'ata-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
dt-bindings: ata: ahci-fsl-qoriq: add fsl,ls1046a-ahci and fsl,ls1012a-ahci
ata: ahci: Add debug print for external port
ata,scsi: Remove wrapper ata_sas_port_alloc()
ata: libata-core: Reuse available ata_port print_ids
ata: libata: Assign print_id at port allocation time
ata: libata-core: Remove local_port_no struct member
ata: libata-sata: Remove superfluous assignment in ata_sas_port_alloc()
ata: libata-core: Remove support for decreasing the number of ports
ata: libata: Remove unused function declaration for ata_scsi_detect()
ata,scsi: Remove wrappers ata_sas_tport_{add,delete}()
ata: libata-scsi: Check ATA_QCFLAG_RTF_FILLED before using result_tf
ata: libata-core: Set ATA_QCFLAG_RTF_FILLED in fill_result_tf()
ata: libata-scsi: Do not pass ATA device id to ata_to_sense_error()
ata: libata-scsi: Remove redundant sense_buffer memsets
ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error
ata: libata-scsi: Do not overwrite valid sense data when CK_COND=1
ata: libata-scsi: Fix offsets for the fixed format sense data
dt-bindings: ata: ahci-fsl-qoriq: convert to yaml format
ata: Kconfig: Update SATA_MOBILE_LPM_POLICY default to med_power_with_dipm
|
|
Pull block updates from Jens Axboe:
- NVMe updates via Keith:
- Device initialization memory leak fixes (Keith)
- More constants defined (Weiwen)
- Target debugfs support (Hannes)
- PCIe subsystem reset enhancements (Keith)
- Queue-depth multipath policy (Redhat and PureStorage)
- Implement get_unique_id (Christoph)
- Authentication error fixes (Gaosheng)
- MD updates via Song
- sync_action fix and refactoring (Yu Kuai)
- Various small fixes (Christoph Hellwig, Li Nan, and Ofir Gal, Yu
Kuai, Benjamin Marzinski, Christophe JAILLET, Yang Li)
- Fix loop detach/open race (Gulam)
- Fix lower control limit for blk-throttle (Yu)
- Add module descriptions to various drivers (Jeff)
- Add support for atomic writes for block devices, and statx reporting
for same. Includes SCSI and NVMe (John, Prasad, Alan)
- Add IO priority information to block trace points (Dongliang)
- Various zone improvements and tweaks (Damien)
- mq-deadline tag reservation improvements (Bart)
- Ignore direct reclaim swap writes in writeback throttling (Baokun)
- Block integrity improvements and fixes (Anuj)
- Add basic support for rust based block drivers. Has a dummy null_blk
variant for now (Andreas)
- Series converting driver settings to queue limits, and cleanups and
fixes related to that (Christoph)
- Cleanup for poking too deeply into the bvec internals, in preparation
for DMA mapping API changes (Christoph)
- Various minor tweaks and fixes (Jiapeng, John, Kanchan, Mikulas,
Ming, Zhu, Damien, Christophe, Chaitanya)
* tag 'for-6.11/block-20240710' of git://git.kernel.dk/linux: (206 commits)
floppy: add missing MODULE_DESCRIPTION() macro
loop: add missing MODULE_DESCRIPTION() macro
ublk_drv: add missing MODULE_DESCRIPTION() macro
xen/blkback: add missing MODULE_DESCRIPTION() macro
block/rnbd: Constify struct kobj_type
block: take offset into account in blk_bvec_map_sg again
block: fix get_max_segment_size() warning
loop: Don't bother validating blocksize
virtio_blk: Don't bother validating blocksize
null_blk: Don't bother validating blocksize
block: Validate logical block size in blk_validate_limits()
virtio_blk: Fix default logical block size fallback
nvmet-auth: fix nvmet_auth hash error handling
nvme: implement ->get_unique_id
block: pass a phys_addr_t to get_max_segment_size
block: add a bvec_phys helper
blk-lib: check for kill signal in ioctl BLKZEROOUT
block: limit the Write Zeroes to manually writing zeroes fallback
block: refacto blkdev_issue_zeroout
block: move read-only and supported checks into (__)blkdev_issue_zeroout
...
|
|
Pull in bug fixes.
|
|
qc->result_tf contents are only valid when the ATA_QCFLAG_RTF_FILLED flag
is set. The ATA_QCFLAG_RTF_FILLED flag should be always set for commands
that failed or for commands that have the ATA_QCFLAG_RESULT_TF flag set.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240702024735.1152293-8-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
ATA device id is not used in ata_to_sense_error().
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240702024735.1152293-6-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
SCSI layer clears sense_buffer in scsi_queue_rq() so there is no need for
libata to clear it again.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240702024735.1152293-5-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
SAT-5 revision 8 specification removed the text about the ANSI INCITS
431-2007 compliance which was requiring SCSI/ATA Translation (SAT) to
return descriptor format sense data for the ATA PASS-THROUGH commands
regardless of the setting of the D_SENSE bit.
Let's honor the D_SENSE bit for ATA PASS-THROUGH commands while
generating the "ATA PASS-THROUGH INFORMATION AVAILABLE" sense data.
SAT-5 revision 7
================
12.2.2.8 Fixed format sense data
Table 212 shows the fields returned in the fixed format sense data
(see SPC-5) for ATA PASS-THROUGH commands. SATLs compliant with ANSI
INCITS 431-2007, SCSI/ATA Translation (SAT) return descriptor format
sense data for the ATA PASS-THROUGH commands regardless of the setting
of the D_SENSE bit.
SAT-5 revision 8
================
12.2.2.8 Fixed format sense data
Table 211 shows the fields returned in the fixed format sense data
(see SPC-5) for ATA PASS-THROUGH commands.
Cc: stable@vger.kernel.org # 4.19+
Reported-by: Niklas Cassel <cassel@kernel.org>
Closes: https://lore.kernel.org/linux-ide/Zn1WUhmLglM4iais@ryzen.lan
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240702024735.1152293-4-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Current ata_gen_passthru_sense() code performs two actions:
1. Generates sense data based on the ATA 'status' and ATA 'error' fields.
2. Populates "ATA Status Return sense data descriptor" / "Fixed format
sense data" with ATA taskfile fields.
The problem is that #1 generates sense data even when a valid sense data
is already present (ATA_QCFLAG_SENSE_VALID is set). Factoring out #2 into
a separate function allows us to generate sense data only when there is
no valid sense data (ATA_QCFLAG_SENSE_VALID is not set).
As a bonus, we can now delete a FIXME comment in atapi_qc_complete()
which states that we don't want to translate taskfile registers into
sense descriptors for ATAPI.
Additionally, always set SAM_STAT_CHECK_CONDITION when CK_COND=1 because
SAT specification mandates that SATL shall return CHECK CONDITION if
the CK_COND bit is set.
The ATA PASS-THROUGH handling logic in ata_scsi_qc_complete() is hard
to read/understand. Improve the readability of the code by moving checks
into self-explanatory boolean variables.
Cc: stable@vger.kernel.org # 4.19+
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240702024735.1152293-3-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Correct the ATA PASS-THROUGH fixed format sense data offsets to conform
to SPC-6 and SAT-5 specifications. Additionally, set the VALID bit to
indicate that the INFORMATION field contains valid information.
INFORMATION
===========
SAT-5 Table 212 — "Fixed format sense data INFORMATION field for the ATA
PASS-THROUGH commands" defines the following format:
+------+------------+
| Byte | Field |
+------+------------+
| 0 | ERROR |
| 1 | STATUS |
| 2 | DEVICE |
| 3 | COUNT(7:0) |
+------+------------+
SPC-6 Table 48 - "Fixed format sense data" specifies that the INFORMATION
field starts at byte 3 in sense buffer resulting in the following offsets
for the ATA PASS-THROUGH commands:
+------------+-------------------------+
| Field | Offset in sense buffer |
+------------+-------------------------+
| ERROR | 3 |
| STATUS | 4 |
| DEVICE | 5 |
| COUNT(7:0) | 6 |
+------------+-------------------------+
COMMAND-SPECIFIC INFORMATION
============================
SAT-5 Table 213 - "Fixed format sense data COMMAND-SPECIFIC INFORMATION
field for ATA PASS-THROUGH" defines the following format:
+------+-------------------+
| Byte | Field |
+------+-------------------+
| 0 | FLAGS | LOG INDEX |
| 1 | LBA (7:0) |
| 2 | LBA (15:8) |
| 3 | LBA (23:16) |
+------+-------------------+
SPC-6 Table 48 - "Fixed format sense data" specifies that
the COMMAND-SPECIFIC-INFORMATION field starts at byte 8
in sense buffer resulting in the following offsets for
the ATA PASS-THROUGH commands:
Offsets of these fields in the fixed sense format are as follows:
+-------------------+-------------------------+
| Field | Offset in sense buffer |
+-------------------+-------------------------+
| FLAGS | LOG INDEX | 8 |
| LBA (7:0) | 9 |
| LBA (15:8) | 10 |
| LBA (23:16) | 11 |
+-------------------+-------------------------+
Reported-by: Akshat Jain <akshatzen@google.com>
Fixes: 11093cb1ef56 ("libata-scsi: generate correct ATA pass-through sense")
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Link: https://lore.kernel.org/r/20240702024735.1152293-2-ipylypiv@google.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
dma_pad_mask is a queue_limits by all ways of looking at it, so move it
there and set it through the atomic queue limits APIs.
Add a little helper that takes the alignment and pad into account to
simplify the code that is touched a bit.
Note that there never was any need for the > check in
blk_queue_update_dma_pad, this probably was just copy and paste from
dma_update_dma_alignment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240626142637.300624-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The SCSI Removable Media Bit (RMB) should only be set for removable media,
where the device stays and the media changes, e.g. CD-ROM or floppy.
The ATA removable media device bit is obsoleted since ATA-8 ACS (2006),
but before that it was used to indicate that the device can have its media
removed (while the device stays).
Commit 8a3e33cf92c7 ("ata: ahci: find eSATA ports and flag them as
removable") introduced a change to set the RMB bit if the port has either
the eSATA bit or the hot-plug capable bit set. The reasoning was that the
author wanted his eSATA ports to get treated like a USB stick.
This is however wrong. See "20-082r23SPC-6: Removable Medium Bit
Expectations" which has since been integrated to SPC, which states that:
"""
Reports have been received that some USB Memory Stick device servers set
the removable medium (RMB) bit to one. The rub comes when the medium is
actually removed, because... The device server is removed concurrently
with the medium removal. If there is no device server, then there is no
device server that is waiting to have removable medium inserted.
Sufficient numbers of SCSI analysts see such a device:
- not as a device that supports removable medium;
but
- as a removable, hot pluggable device.
"""
The definition of the RMB bit in the SPC specification has since been
clarified to match this.
Thus, a USB stick should not have the RMB bit set (and neither shall an
eSATA nor a hot-plug capable port).
Commit dc8b4afc4a04 ("ata: ahci: don't mark HotPlugCapable Ports as
external/removable") then changed so that the RMB bit is only set for the
eSATA bit (and not for the hot-plug capable bit), because of a lot of bug
reports of SATA devices were being automounted by udisks. However,
treating eSATA and hot-plug capable ports differently is not correct.
From the AHCI 1.3.1 spec:
Hot Plug Capable Port (HPCP): When set to '1', indicates that this port's
signal and power connectors are externally accessible via a joint signal
and power connector for blindmate device hot plug.
So a hot-plug capable port is an external port, just like commit
45b96d65ec68 ("ata: ahci: a hotplug capable port is an external port")
claims.
In order to not violate the SPC specification, modify the SCSI INQUIRY
data to only set the RMB bit if the ATA device can have its media removed.
This fixes a reported problem where GNOME/udisks was automounting devices
connected to hot-plug capable ports.
Fixes: 45b96d65ec68 ("ata: ahci: a hotplug capable port is an external port")
Cc: stable@vger.kernel.org
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Thomas Weißschuh <linux@weissschuh.net>
Reported-by: Thomas Weißschuh <linux@weissschuh.net>
Closes: https://lore.kernel.org/linux-ide/c0de8262-dc4b-4c22-9fac-33432e5bddd3@t-8ch.de/
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[cassel: wrote commit message]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers.
The remaining patches are assorted minor fixes and deprecated function
updates plus a bit of constification"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: mpi3mr: Sanitise num_phys
scsi: lpfc: Copyright updates for 14.4.0.2 patches
scsi: lpfc: Update lpfc version to 14.4.0.2
scsi: lpfc: Add support for 32 byte CDBs
scsi: lpfc: Change lpfc_hba hba_flag member into a bitmask
scsi: lpfc: Introduce rrq_list_lock to protect active_rrq_list
scsi: lpfc: Clear deferred RSCN processing flag when driver is unloading
scsi: lpfc: Update logging of protection type for T10 DIF I/O
scsi: lpfc: Change default logging level for unsolicited CT MIB commands
scsi: target: Remove unused list 'device_list'
scsi: iscsi: Remove unused list 'connlist_err'
scsi: ufs: exynos: Add support for Tensor gs101 SoC
scsi: ufs: exynos: Add some pa_dbg_ register offsets into drvdata
scsi: ufs: exynos: Allow max frequencies up to 267Mhz
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_TIMER_TICK_SELECT option
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_UFSPR_SECURE option
scsi: ufs: dt-bindings: exynos: Add gs101 compatible
scsi: qla2xxx: Fix debugfs output for fw_resource_count
scsi: qedf: Ensure the copied buf is NUL terminated
scsi: bfa: Ensure the copied buf is NUL terminated
...
|
|
Commit 0c76106cb975 ("scsi: sd: Fix TCG OPAL unlock on system resume")
incorrectly handles failures of scsi_resume_device() in
ata_scsi_dev_rescan(), leading to a double call to
spin_unlock_irqrestore() to unlock a device port. Fix this by redefining
the goto labels used in case of errors and only unlock the port
scsi_scan_mutex when scsi_resume_device() fails.
Bug found with the Smatch static checker warning:
drivers/ata/libata-scsi.c:4774 ata_scsi_dev_rescan()
error: double unlocked 'ap->lock' (orig line 4757)
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 0c76106cb975 ("scsi: sd: Fix TCG OPAL unlock on system resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Switch to the ->device_configure method instead of ->slave_configure and
update the block limits on the passed in queue_limits instead of using the
per-limit accessors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-21-hch@lst.de
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop
management") introduced the manage_system_start_stop scsi_device flag to
allow libata to indicate to the SCSI disk driver that nothing should be
done when resuming a disk on system resume. This change turned the
execution of sd_resume() into a no-op for ATA devices on system
resume. While this solved deadlock issues during device resume, this change
also wrongly removed the execution of opal_unlock_from_suspend(). As a
result, devices with TCG OPAL locking enabled remain locked and
inaccessible after a system resume from sleep.
To fix this issue, introduce the SCSI driver resume method and implement it
with the sd_resume() function calling opal_unlock_from_suspend(). The
former sd_resume() function is renamed to sd_resume_common() and modified
to call the new sd_resume() function. For non-ATA devices, this result in
no functional changes.
In order for libata to explicitly execute sd_resume() when a device is
resumed during system restart, the function scsi_resume_device() is
introduced. libata calls this function from the revalidation work executed
on devie resume, a state that is indicated with the new device flag
ATA_DFLAG_RESUMING. Doing so, locked TCG OPAL enabled devices are unlocked
on resume, allowing normal operation.
Fixes: 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop management")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218538
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240319071209.1179257-1-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is not always possible to keep a device in the runtime suspended state
when a system level suspend/resume cycle is executed. E.g. for ATA devices
connected to AHCI adapters, system resume resets the ATA ports, which
causes connected devices to spin up. In such case, a runtime suspended disk
will incorrectly be seen with a suspended runtime state because the device
is not resumed by sd_resume_system(). The power state seen by the user is
different than the actual device physical power state.
Fix this issue by introducing the struct scsi_device flag
force_runtime_start_on_system_start. When set, this flag causes
sd_resume_system() to request a runtime resume operation for runtime
suspended devices. This results in the user seeing the device runtime_state
as active after a system resume, thus correctly reflecting the device
physical power state.
Fixes: 9131bff6a9f1 ("scsi: core: pm: Only runtime resume if necessary")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20231120225631.37938-3-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop
management") changed the single bit manage_start_stop flag into 2 boolean
fields of the SCSI device structure. Commit 24eca2dce0f8 ("scsi: sd:
Introduce manage_shutdown device flag") introduced the manage_shutdown
boolean field for the same structure. Together, these 2 commits increase
the size of struct scsi_device by 8 bytes by using booleans instead of
defining the manage_xxx fields as single bit flags, similarly to other
flags of this structure.
Avoid this unnecessary structure size increase and be consistent with the
definition of other flags by reverting the definitions of the manage_xxx
fields as single bit flags.
Fixes: 3cc2ffe5c16d ("scsi: sd: Differentiate system and runtime start/stop management")
Fixes: 24eca2dce0f8 ("scsi: sd: Introduce manage_shutdown device flag")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20231120225631.37938-2-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA updates from Damien Le Moal:
- Modify the AHCI driver to print the link power management policy used
on scan, to help with debugging issues (Niklas)
- Add support for the ASM2116 series adapters to the AHCI driver
(Szuying)
- Prepare libata for the coming gcc and Clang __counted_by attribute
(Kees)
- Following the recent estensive fixing of libata suspend/resume
handling, several patches further cleanup and improve disk power
state management (me)
- Reduce the verbosity of some error messages for non-fatal temporary
errors, e.g. slow response to device reset when scanning a port, and
warning messages that are in fact normal, e.g. disabling a device on
suspend or when removing it (me)
- Cleanup DMA helper functions (me)
- Fix sata_mv drive handling of potential errors durring probe (Ma)
- Cleanup the xgene and imx drivers using the functions
of_device_get_match_data() and device_get_match_data() (Rob)
- Improve the tegra driver device tree (Rob)
* tag 'ata-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (22 commits)
dt-bindings: ata: tegra: Disallow undefined properties
ata: libata-core: Improve ata_dev_power_set_active()
ata: libata-eh: Spinup disk on resume after revalidation
ata: imx: Use device_get_match_data()
ata: xgene: Use of_device_get_match_data()
ata: sata_mv: aspeed: fix value check in mv_platform_probe()
ata: ahci: Add Intel Alder Lake-P AHCI controller to low power chipsets list
ata: libata: Cleanup inline DMA helper functions
ata: libata-eh: Reduce "disable device" message verbosity
ata: libata-eh: Improve reset error messages
ata: libata-sata: Improve ata_sas_slave_configure()
ata: libata-core: Do not resume runtime suspended ports
ata: libata-core: Do not poweroff runtime suspended ports
ata: libata-core: Remove ata_port_resume_async()
ata: libata-core: Remove ata_port_suspend_async()
ata: libata-core: Detach a port devices on shutdown
ata: libata-core: Synchronize ata_port_detach() with hotplug
ata: libata-scsi: Cleanup ata_scsi_start_stop_xlat()
scsi: Remove scsi device no_start_on_resume flag
ata: libata: Annotate struct ata_cpr_log with __counted_by
...
|
|
Commit aa3998dbeb3a ("ata: libata-scsi: Disable scsi device
manage_system_start_stop") change setting the manage_system_start_stop
flag to false for libata managed disks to enable libata internal
management of disk suspend/resume. However, a side effect of this change
is that on system shutdown, disks are no longer being stopped (set to
standby mode with the heads unloaded). While this is not a critical
issue, this unclean shutdown is not recommended and shows up with
increased smart counters (e.g. the unexpected power loss counter
"Unexpect_Power_Loss_Ct").
Instead of defining a shutdown driver method for all ATA adapter
drivers (not all of them define that operation), this patch resolves
this issue by further refining the sd driver start/stop control of disks
using the new flag manage_shutdown. If this new flag is set to true by
a low level driver, the function sd_shutdown() will issue a
START STOP UNIT command with the start argument set to 0 when a disk
needs to be powered off (suspended) on system power off, that is, when
system_state is equal to SYSTEM_POWER_OFF.
Similarly to the other manage_xxx flags, the new manage_shutdown flag is
exposed through sysfs as a read-write device attribute.
To avoid any confusion between manage_shutdown and
manage_system_start_stop, the comments describing these flags in
include/scsi/scsi.h are also improved.
Fixes: aa3998dbeb3a ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218038
Link: https://lore.kernel.org/all/cd397c88-bf53-4768-9ab8-9d107df9e613@gmail.com/
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Now that libata does its own internal device power mode management
through libata EH, the scsi disk driver will not issue START STOP UNIT
commands anymore. We can receive this command only from user passthrough
operations. So there is no need to consider the system state and ATA
port flags for suspend to translate the command.
Since setting up the taskfile for the verify and standby
immediate commands is the same as done in ata_dev_power_set_active()
and ata_dev_power_set_standby(), factor out this code into the helper
function ata_dev_power_init_tf() to simplify ata_scsi_start_stop_xlat()
as well as ata_dev_power_set_active() and ata_dev_power_set_standby().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fixes from Damien Le Moal:
"A larger than usual set of fixes for 6.6-rc4 due to the unexpected
number of fixes needed to address ATA disks suspend/resume issues.
In more detail:
- Add missing additionalProperties on child nodes to the pata-common
DT bindings (Rob)
- Fix handling of the REPORT SUPPORTED OPERATION CODES command to
ignore reserved bits (Niklas)
- Increase port multiplier soft reset timeout to accomodate slow
devices and avoid issues on wakeup (Matthias)
- A couple of minor code fixes to avoid compilation warnings in
libata-core and libata-eh (me)
- Many patches from me to address suspend/resume issues, and in
particular a potential deadlock on resume due to the SCSI disk
driver resume operation not being synchronized with libata EH port
resume handling.
This is addressed by changing the scsi disk driver disk start/stop
control to allow libata to execute disk suspend (spin down) and
resume (spin up) on its own during system suspend/resume. Runtime
suspend/resume control remains with the SCSI disk driver.
Other fixes include:
- Fix libata power management request issuing to avoid races
- Establish a link between ATA ports and SCSI devices to order PM
operations
- Fix device removal to avoid issues with driver rmmod removal
- Fix synchronization of libata device rescan and SCSI disk resume
operation
- Remove libsas PM operations as suspend/resume is handled
directly by the sas controller resume
- Fix the SCSI disk driver to not issue commands to suspended
disks, thus avoiding potential system lock-up on resume"
* tag 'ata-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-eh: Fix compilation warning in ata_eh_link_report()
ata: libata-core: Fix compilation warning in ata_dev_config_ncq()
scsi: sd: Do not issue commands to suspended disks on shutdown
ata: libata-core: Do not register PM operations for SAS ports
ata: libata-scsi: Fix delayed scsi_rescan_device() execution
scsi: Do not attempt to rescan suspended devices
ata: libata-scsi: Disable scsi device manage_system_start_stop
scsi: sd: Differentiate system and runtime start/stop management
ata: libata-scsi: link ata port and scsi device
ata: libata-core: Fix port and device removal
ata: libata-core: Fix ata_port_request_pm() locking
ata: libata-sata: increase PMP SRST timeout to 10s
ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES
dt-bindings: ata: pata-common: Add missing additionalProperties on child nodes
|
|
Commit 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after
device resume") modified ata_scsi_dev_rescan() to check the scsi device
"is_suspended" power field to ensure that the scsi device associated
with an ATA device is fully resumed when scsi_rescan_device() is
executed. However, this fix is problematic as:
1) It relies on a PM internal field that should not be used without PM
device locking protection.
2) The check for is_suspended and the call to scsi_rescan_device() are
not atomic and a suspend PM event may be triggered between them,
casuing scsi_rescan_device() to be called on a suspended device and
in that function blocking while holding the scsi device lock. This
would deadlock a following resume operation.
These problems can trigger PM deadlocks on resume, especially with
resume operations triggered quickly after or during suspend operations.
E.g., a simple bash script like:
for (( i=0; i<10; i++ )); do
echo "+2 > /sys/class/rtc/rtc0/wakealarm
echo mem > /sys/power/state
done
that triggers a resume 2 seconds after starting suspending a system can
quickly lead to a PM deadlock preventing the system from correctly
resuming.
Fix this by replacing the check on is_suspended with a check on the
return value given by scsi_rescan_device() as that function will fail if
called against a suspended device. Also make sure rescan tasks already
scheduled are first cancelled before suspending an ata port.
Fixes: 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The introduction of a device link to create a consumer/supplier
relationship between the scsi device of an ATA device and the ATA port
of that ATA device fixes the ordering of system suspend and resume
operations. For suspend, the scsi device is suspended first and the ata
port after it. This is fine as this allows the synchronize cache and
START STOP UNIT commands issued by the scsi disk driver to be executed
before the ata port is disabled.
For resume operations, the ata port is resumed first, followed
by the scsi device. This allows having the request queue of the scsi
device to be unfrozen after the ata port resume is scheduled in EH,
thus avoiding to see new requests prematurely issued to the ATA device.
Since libata sets manage_system_start_stop to 1, the scsi disk resume
operation also results in issuing a START STOP UNIT command to the
device being resumed so that the device exits standby power mode.
However, restoring the ATA device to the active power mode must be
synchronized with libata EH processing of the port resume operation to
avoid either 1) seeing the start stop unit command being received too
early when the port is not yet resumed and ready to accept commands, or
after the port resume process issues commands such as IDENTIFY to
revalidate the device. In this last case, the risk is that the device
revalidation fails with timeout errors as the drive is still spun down.
Commit 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
disabled issuing the START STOP UNIT command to avoid issues with it.
But this is incorrect as transitioning a device to the active power
mode from the standby power mode set on suspend requires a media access
command. The IDENTIFY, READ LOG and SET FEATURES commands executed in
libata EH context triggered by the ata port resume operation may thus
fail.
Fix these synchronization issues is by handling a device power mode
transitions for system suspend and resume directly in libata EH context,
without relying on the scsi disk driver management triggered with the
manage_system_start_stop flag.
To do this, the following libata helper functions are introduced:
1) ata_dev_power_set_standby():
This function issues a STANDBY IMMEDIATE command to transitiom a device
to the standby power mode. For HDDs, this spins down the disks. This
function applies only to ATA and ZAC devices and does nothing otherwise.
This function also does nothing for devices that have the
ATA_FLAG_NO_POWEROFF_SPINDOWN or ATA_FLAG_NO_HIBERNATE_SPINDOWN flag
set.
For suspend, call ata_dev_power_set_standby() in
ata_eh_handle_port_suspend() before the port is disabled and frozen.
ata_eh_unload() is also modified to transition all enabled devices to
the standby power mode when the system is shutdown or devices removed.
2) ata_dev_power_set_active() and
This function applies to ATA or ZAC devices and issues a VERIFY command
for 1 sector at LBA 0 to transition the device to the active power mode.
For HDDs, since this function will complete only once the disk spin up.
Its execution uses the same timeouts as for reset, to give the drive
enough time to complete spinup without triggering a command timeout.
For resume, call ata_dev_power_set_active() in
ata_eh_revalidate_and_attach() after the port has been enabled and
before any other command is issued to the device.
With these changes, the manage_system_start_stop and no_start_on_resume
scsi device flags do not need to be set in ata_scsi_dev_config(). The
flag manage_runtime_start_stop is still set to allow the sd driver to
spinup/spindown a disk through the sd runtime operations.
Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.
For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.
Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.
Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is no direct device ancestry defined between an ata_device and
its scsi device which prevents the power management code from correctly
ordering suspend and resume operations. Create such ancestry with the
ata device as the parent to ensure that the scsi device (child) is
suspended before the ata device and that resume handles the ata device
before the scsi device.
The parent-child (supplier-consumer) relationship is established between
the ata_port (parent) and the scsi device (child) with the function
device_add_link(). The parent used is not the ata_device as the PM
operations are defined per port and the status of all devices connected
through that port is controlled from the port operations.
The device link is established with the new function
ata_scsi_slave_alloc(), and this function is used to define the
->slave_alloc callback of the scsi host template of all ata drivers.
Fixes: a19a93e4c6a9 ("scsi: core: pm: Rely on the device driver core for async power management")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
|
|
For REPORT SUPPORTED OPERATION CODES command, the service action field is
defined as bits 0-4 in the second byte in the CDB. Bits 5-7 in the second
byte are reserved.
Only look at the service action field in the second byte when determining
if the MAINTENANCE IN opcode is a REPORT SUPPORTED OPERATION CODES command.
This matches how we only look at the service action field in the second
byte when determining if the SERVICE ACTION IN(16) opcode is a READ
CAPACITY(16) command (reserved bits 5-7 in the second byte are ignored).
Fixes: 7b2030942859 ("libata: Add support for SCT Write Same")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Some old drives (e.g. an Ultra320 SCSI disk as reported by John) do not
seem to execute MAINTENANCE_IN / MI_REPORT_SUPPORTED_OPERATION_CODES
commands correctly and hang when a non-zero service action is specified
(one command format with service action case in scsi_report_opcode()).
Currently, CDL probing with scsi_cdl_check_cmd() is the only caller using a
non zero service action for scsi_report_opcode(). To avoid issues with
these old drives, do not attempt CDL probe if the device reports support
for an SPC version lower than 5 (CDL was introduced in SPC-5). To keep
things working with ATA devices which probe for the CDL T2A and T2B pages
introduced with SPC-6, modify ata_scsiop_inq_std() to claim SPC-6 version
compatibility for ATA drives supporting CDL.
SPC-6 standard version number is defined as Dh (= 13) in SPC-6 r09. Fix
scsi_probe_lun() to correctly capture this value by changing the bit mask
for the second byte of the INQUIRY response from 0x7 to 0xf.
include/scsi/scsi.h is modified to add the definition SCSI_SPC_6 with the
value 14 (Dh + 1). The missing definitions for the SCSI_SPC_4 and
SCSI_SPC_5 versions are also added.
Reported-by: John David Anglin <dave.anglin@bell.net>
Fixes: 624885209f31 ("scsi: core: Detect support for command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230915022034.678121-1-dlemoal@kernel.org
Tested-by: David Gow <david@davidgow.net>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull more SCSI updates from James Bottomley:
"Mostly small stragglers that missed the initial merge.
Driver updates are qla2xxx and smartpqi (mp3sas has a high diffstat
due to the volatile qualifier removal, fnic due to unused function
removal and sd.c has a lot of code shuffling to remove forward
declarations)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (38 commits)
scsi: ufs: core: No need to update UPIU.header.flags and lun in advanced RPMB handler
scsi: ufs: core: Add advanced RPMB support where UFSHCI 4.0 does not support EHS length in UTRD
scsi: mpt3sas: Remove volatile qualifier
scsi: mpt3sas: Perform additional retries if doorbell read returns 0
scsi: libsas: Simplify sas_queue_reset() and remove unused code
scsi: ufs: Fix the build for the old ARM OABI
scsi: qla2xxx: Fix unused variable warning in qla2xxx_process_purls_pkt()
scsi: fnic: Remove unused functions fnic_scsi_host_start/end_tag()
scsi: qla2xxx: Fix spelling mistake "tranport" -> "transport"
scsi: fnic: Replace sgreset tag with max_tag_id
scsi: qla2xxx: Remove unused variables in qla24xx_build_scsi_type_6_iocbs()
scsi: qla2xxx: Fix nvme_fc_rcv_ls_req() undefined error
scsi: smartpqi: Change driver version to 2.1.24-046
scsi: smartpqi: Enhance error messages
scsi: smartpqi: Enhance controller offline notification
scsi: smartpqi: Enhance shutdown notification
scsi: smartpqi: Simplify lun_number assignment
scsi: smartpqi: Rename pciinfo to pci_info
scsi: smartpqi: Rename MACRO to clarify purpose
scsi: smartpqi: Add abort handler
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata updates from Damien Le Moal:
- Fix OF include file for ata platform drivers (Rob)
- Simplify various ahci, sata and pata platform drivers using the
function devm_platform_ioremap_resource() (Yangtao)
- Cleanup libata time related argument types (e.g. timeouts values)
(Sergey)
- Cleanup libata code around error handling as all ata drivers now
define a error_handler operation (Hannes and Niklas)
- Remove functions intended for libsas that are in fact unused (Niklas)
- Change the remove device callback of platform drivers to a null
function (Uwe)
- Simplify the pata_imx driver using devm_clk_get_enabled() (Li)
- Remove old and uinused remnants of the ide code in arm, parisc,
powerpc, sparc and m68k architectures and associated drivers
(pata_buddha, pata_falcon and pata_gayle) (Geert)
- Add missing MODULE_DESCRIPTION() in the sata_gemini and pata_ftide010
drivers (me)
- Several fixes for the pata_ep93xx and pata_falcon drivers (Nikita,
Michael)
- Add Elkhart Lake AHCI controller support to the ahci driver (Werner)
- Disable NCQ trim on Micron 1100 drives (Pawel)
* tag 'ata-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (60 commits)
ata: libata-core: Disable NCQ_TRIM on Micron 1100 drives
ata: ahci: Add Elkhart Lake AHCI controller
ata: pata_falcon: add data_swab option to byte-swap disk data
ata: pata_falcon: fix IO base selection for Q40
ata: pata_ep93xx: use soc_device_match for UDMA modes
ata: pata_ep93xx: fix error return code in probe
ata: sata_gemini: Add missing MODULE_DESCRIPTION
ata: pata_ftide010: Add missing MODULE_DESCRIPTION
m68k: Remove <asm/ide.h>
ata: pata_gayle: Remove #include <asm/ide.h>
ata: pata_falcon: Remove #include <asm/ide.h>
ata: pata_buddha: Remove #include <asm/ide.h>
asm-generic: Remove ide_iops.h
sparc: Remove <asm/ide.h>
powerpc: Remove <asm/ide.h>
parisc: Remove <asm/ide.h>
ARM: Remove <asm/ide.h>
ata: pata_imx: Use helper function devm_clk_get_enabled()
ata: sata_rcar: Convert to platform remove callback returning void
ata: sata_mv: Convert to platform remove callback returning void
...
|
|
Most callers of scsi_rescan_device() have the scsi_device pointer readily
available. Pass a struct scsi_device pointer to scsi_rescan_device()
instead of a struct device pointer. This change prevents that a pointer to
another struct device would be passed accidentally to scsi_rescan_device().
Remove the scsi_rescan_device() declaration from the scsi_priv.h header
file since it duplicates the declaration in <scsi/scsi_host.h>.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230822153043.4046244-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
With commit 65a15d6560df ("scsi: ipr: Remove SATA support") all
libata drivers now have the error_handler() callback provided,
so we can stop checking for non-existing error_handler callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[niklas: fixed review comments, rebased, solved conflicts during rebase,
fixed bug that unconditionally dumped all QCs, removed the now unused
function ata_dump_status(), removed the now unreachable failure paths in
atapi_qc_complete(), removed the non-EH function to request ATAPI sense]
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|