| Age | Commit message (Collapse) | Author |
|---|
|
Mapping the MEMRESERVE EFI configuration table from an early initcall
is too late: the GICv3 ITS code that creates persistent reservations
for the boot CPU's LPI tables is invoked from init_IRQ(), which runs
much earlier than the handling of the initcalls. This results in a
WARN() splat because the LPI tables cannot be reserved persistently,
which will result in silent memory corruption after a kexec reboot.
So instead, invoke the initialization performed by the initcall from
efi_mem_reserve_persistent() itself as well, but keep the initcall so
that the init is guaranteed to have been called before SMP boot.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 63eb322d89c8 ("efi: Permit calling efi_mem_reserve_persistent() ...")
Link: http://lkml.kernel.org/r/20181123215132.7951-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Currently, efi_mem_reserve_persistent() may not be called from atomic
context, since both the kmalloc() call and the memremap() call may
sleep.
The kmalloc() call is easy enough to fix, but the memremap() call
needs to be moved into an init hook since we cannot control the
memory allocation behavior of memremap() at the call site.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20181114175544.12860-6-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The new memory EFI reservation feature we introduced to allow memory
reservations to persist across kexec may trigger an unbounded number
of calls to memblock_reserve(). The memblock subsystem can deal with
this fine, but not before memblock resizing is enabled, which we can
only do after paging_init(), when the memory we reallocate the array
into is actually mapped.
So break out the memreserve table processing into a separate routine
and call it after paging_init() on arm64. On ARM, because of limited
reviewing bandwidth of the maintainer, we cannot currently fix this,
so instead, disable the EFI persistent memreserve entirely on ARM so
we can fix it later.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20181114175544.12860-5-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit:
24d7c494ce46 ("efi/arm-stub: Round up FDT allocation to mapping size")
increased the allocation size for the FDT image created by the stub to a
fixed value of 2 MB, to simplify the former code that made several
attempts with increasing values for the size. This is reasonable
given that the allocation is of type EFI_LOADER_DATA, which is released
to the kernel unless it is explicitly memblock_reserve()d by the early
boot code.
However, this allocation size leaked into the 'size' field of the FDT
header metadata, and so the entire allocation remains occupied by the
device tree binary, even if most of it is not used to store device tree
information.
So call fdt_pack() to shrink the FDT data structure to its minimum size
after populating all the fields, so that the remaining memory is no
longer wasted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.12+
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 24d7c494ce46 ("efi/arm-stub: Round up FDT allocation to mapping size")
Link: http://lkml.kernel.org/r/20181114175544.12860-4-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit:
3ea86495aef2 ("efi/arm: preserve early mapping of UEFI memory map longer for BGRT")
deferred the unmap of the early mapping of the UEFI memory map to
accommodate the ACPI BGRT code, which looks up the memory type that
backs the BGRT table to validate it against the requirements of the UEFI spec.
Unfortunately, this causes problems on ARM, which does not permit
early mappings to persist after paging_init() is called, resulting
in a WARN() splat. Since we don't support the BGRT table on ARM anway,
let's revert ARM to the old behaviour, which is to take down the
early mapping at the end of efi_init().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 3ea86495aef2 ("efi/arm: preserve early mapping of UEFI memory ...")
Link: http://lkml.kernel.org/r/20181114175544.12860-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The following commit:
9dbbedaa6171 ("efi: Make efi_rts_work accessible to efi page fault handler")
converted 'efi_rts_work' from an auto variable to a global variable.
However, when submitting the work, INIT_WORK_ONSTACK() was still used,
causing the following complaint from debugobjects:
ODEBUG: object 00000000ed27b500 is NOT on stack 00000000c7d38760, but annotated.
Change the macro to just INIT_WORK() to eliminate the warning.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 9dbbedaa6171 ("efi: Make efi_rts_work accessible to efi page fault handler")
Link: http://lkml.kernel.org/r/20181114175544.12860-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A number of fixes and some late updates:
- make in_compat_syscall() behavior on x86-32 similar to other
platforms, this touches a number of generic files but is not
intended to impact non-x86 platforms.
- objtool fixes
- PAT preemption fix
- paravirt fixes/cleanups
- cpufeatures updates for new instructions
- earlyprintk quirk
- make microcode version in sysfs world-readable (it is already
world-readable in procfs)
- minor cleanups and fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Cleanup in_compat_syscall() callers
x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
objtool: Support GCC 9 cold subfunction naming scheme
x86/numa_emulation: Fix uniform-split numa emulation
x86/paravirt: Remove unused _paravirt_ident_32
x86/mm/pat: Disable preemption around __flush_tlb_all()
x86/paravirt: Remove GPL from pv_ops export
x86/traps: Use format string with panic() call
x86: Clean up 'sizeof x' => 'sizeof(x)'
x86/cpufeatures: Enumerate MOVDIR64B instruction
x86/cpufeatures: Enumerate MOVDIRI instruction
x86/earlyprintk: Add a force option for pciserial device
objtool: Support per-function rodata sections
x86/microcode: Make revision and processor flags world-readable
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
- Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86
as they are closely coupled with other drivers in this location.
- Improve _init* usage for acerhdf and fix some usage issues with
messages and module parameters.
- Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
workqueue overhead, eliminate double reporting of keyboard backlight.
- Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).
- Notify intel_telemetry users when IPC1 device is not enabled.
- Update various drivers with new laptop model IDs.
- Update several intel drivers to use SPDX identifers and order headers
alphabetically.
* tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86: (64 commits)
HID: asus: only support backlight when it's not driven by WMI
platform/x86: asus-wmi: export function for evaluating WMI methods
platform/x86: asus-wmi: Only notify kbd LED hw_change by fn-key pressed
platform/x86: wmi: declare device_type structure as constant
platform/x86: ideapad: Add Y530-15ICH to no_hw_rfkill
platform/x86: Add Intel AtomISP2 dummy / power-management driver
platform/x86: touchscreen_dmi: Add min-x and min-y settings for various models
platform/x86: touchscreen_dmi: Add info for the Onda V80 Plus v3 tablet
platform/x86: touchscreen_dmi: Add info for the Trekstor Primetab T13B tablet
platform/x86: intel_telemetry: Get rid of custom macro
platform/x86: intel_telemetry: report debugfs failure
MAINTAINERS: intel_telemetry: Update maintainers info
platform/x86: Add LG Gram laptop special features driver
platform/x86: asus-wmi: Simplify the keyboard brightness updating process
platform/x86: touchscreen_dmi: Add info for the Trekstor Primebook C11 convertible
platform/x86: mlx-platform: Properly use mlxplat_mlxcpld_msn201x_items
MAINTAINERS: intel_pmc_core: Update MAINTAINERS
firmware: dcdbas: include linux/io.h
platform/x86: intel-wmi-thunderbolt: Add dynamic debugging
platform/x86: intel-wmi-thunderbolt: Convert to use SPDX identifier
...
|
|
Now that in_compat_syscall() is consistent on all architectures and does
not longer report true on native i686, the workarounds (ifdeffery and
helpers) can be removed.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-efi@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: https://lkml.kernel.org/r/20181012134253.23266-3-dima@arista.com
|
|
When a memblock allocation APIs are called with align = 0, the alignment
is implicitly set to SMP_CACHE_BYTES.
Implicit alignment is done deep in the memblock allocator and it can
come as a surprise. Not that such an alignment would be wrong even
when used incorrectly but it is better to be explicit for the sake of
clarity and the prinicple of the least surprise.
Replace all such uses of memblock APIs with the 'align' parameter
explicitly set to SMP_CACHE_BYTES and stop implicit alignment assignment
in the memblock internal allocation functions.
For the case when memblock APIs are used via helper functions, e.g. like
iommu_arena_new_node() in Alpha, the helper functions were detected with
Coccinelle's help and then manually examined and updated where
appropriate.
The direct memblock APIs users were updated using the semantic patch below:
@@
expression size, min_addr, max_addr, nid;
@@
(
|
- memblock_alloc_try_nid_raw(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_raw(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid_nopanic(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_nopanic(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid(size, SMP_CACHE_BYTES, min_addr, max_addr, nid)
|
- memblock_alloc(size, 0)
+ memblock_alloc(size, SMP_CACHE_BYTES)
|
- memblock_alloc_raw(size, 0)
+ memblock_alloc_raw(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from(size, 0, min_addr)
+ memblock_alloc_from(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_nopanic(size, 0)
+ memblock_alloc_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low(size, 0)
+ memblock_alloc_low(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low_nopanic(size, 0)
+ memblock_alloc_low_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from_nopanic(size, 0, min_addr)
+ memblock_alloc_from_nopanic(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_node(size, 0, nid)
+ memblock_alloc_node(size, SMP_CACHE_BYTES, nid)
)
[mhocko@suse.com: changelog update]
[akpm@linux-foundation.org: coding-style fixes]
[rppt@linux.ibm.com: fix missed uses of implicit alignment]
Link: http://lkml.kernel.org/r/20181016133656.GA10925@rapoport-lnx
Link: http://lkml.kernel.org/r/1538687224-17535-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The free_bootmem_late and memblock_free_late do exactly the same thing:
they iterate over a range and give pages to the page allocator.
Replace calls to free_bootmem_late with calls to memblock_free_late and
remove the bootmem variant.
Link: http://lkml.kernel.org/r/1536927045-23536-25-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The conversion is done using
sed -i 's@memblock_virt_alloc@memblock_alloc@g' \
$(git grep -l memblock_virt_alloc)
Link: http://lkml.kernel.org/r/1536927045-23536-8-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make it explicit that the caller gets a physical address rather than a
virtual one.
This will also allow using meblock_alloc prefix for memblock allocations
returning virtual address, which is done in the following patches.
The conversion is done using the following semantic patch:
@@
expression e1, e2, e3;
@@
(
- memblock_alloc(e1, e2)
+ memblock_phys_alloc(e1, e2)
|
- memblock_alloc_nid(e1, e2, e3)
+ memblock_phys_alloc_nid(e1, e2, e3)
|
- memblock_alloc_try_nid(e1, e2, e3)
+ memblock_phys_alloc_try_nid(e1, e2, e3)
)
Link: http://lkml.kernel.org/r/1536927045-23536-7-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc patches for 4.20-rc1.
Loads of things here, we have new code in all of these driver
subsystems:
- fpga
- stm
- extcon
- nvmem
- eeprom
- hyper-v
- gsmi
- coresight
- thunderbolt
- vmw_balloon
- goldfish
- soundwire
along with lots of fixes and minor changes to other small drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (245 commits)
Documentation/security-bugs: Clarify treatment of embargoed information
lib: Fix ia64 bootloader linkage
MAINTAINERS: Clarify UIO vs UIOVEC maintainer
docs/uio: fix a grammar nitpick
docs: fpga: document programming fpgas using regions
fpga: add devm_fpga_region_create
fpga: bridge: add devm_fpga_bridge_create
fpga: mgr: add devm_fpga_mgr_create
hv_balloon: Replace spin_is_locked() with lockdep
sgi-xp: Replace spin_is_locked() with lockdep
eeprom: New ee1004 driver for DDR4 memory
eeprom: at25: remove unneeded 'at25_remove'
w1: IAD Register is yet readable trough iad sys file. Fix snprintf (%u for unsigned, count for max size).
misc: mic: scif: remove set but not used variables 'src_dma_addr, dst_dma_addr'
misc: mic: fix a DMA pool free failure
platform: goldfish: pipe: Add a blank line to separate varibles and code
platform: goldfish: pipe: Remove redundant casting
platform: goldfish: pipe: Call misc_deregister if init fails
platform: goldfish: pipe: Move the file-scope goldfish_pipe_dev variable into the driver state
platform: goldfish: pipe: Move the file-scope goldfish_pipe_miscdev variable into the driver state
...
|
|
Add new GSMI commands (GSMI_CMD_LOG_S0IX_SUSPEND = 0xa,
GSMI_CMD_LOG_S0IX_RESUME = 0xb) that allow firmware to log any
information during S0ix suspend/resume paths.
Traditional ACPI suspend S3 involves BIOS both during the suspend and
the resume paths. However, modern suspend type like S0ix does not
involve firmware on either of the paths. This command gives the
firmware an opportunity to log any required information about the
suspend and resume operations e.g. wake sources.
Additionally, this change adds a module parameter to allow platforms
to specifically enable S0ix logging if required. This prevents any
other platforms from unnecessarily making a GSMI call which could have
any side-effects.
Tested by verifying that wake sources are correctly logged in eventlog.
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rajat Jain <rajatja@chromium.org>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
[zwisler: update changelog for upstream]
Signed-off-by: Ross Zwisler <zwisler@google.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of selecting EFI and EFI_VARS automatically when GSMI is
enabled let that portion of the driver be conditionally compiled
if EFI and EFI_VARS are enabled.
This allows the rest of the driver (specifically event log) to
be used if EFI_VARS is not enabled.
To test:
1) verify that EFI_VARS is not automatically selected when
CONFIG_GOOGLE_GSMI is enabled
2) verify that the kernel boots on Link and that GSMI event log
is still available and functional
3) specifically boot the kernel on Alex to ensure it does not
try to load efivars and that gsmi also does not load because it
is not in the supported DMI table
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Filipe Brandenburger <filbranden@chromium.org>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
[zwisler: update changelog for upstream]
Signed-off-by: Ross Zwisler <zwisler@google.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to use this coreboot needs board support for:
CONFIG_ELOG=y
CONFIG_ELOG_GSMI=y
And the kernel driver needs enabled:
CONFIG_GOOGLE_GSMI=y
To test, verify that clean shutdown event is added to the log:
> mosys eventlog list | grep 'Clean Shutdown'
11 | 2012-06-25 09:49:24 | Kernl Event | Clean Shutdown
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
[zwisler: update changelog for upstream]
Signed-off-by: Ross Zwisler <zwisler@google.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sysfs handler should return the number of bytes consumed, which in the
case of a successful write is the entire buffer. Also fix a bug where
param.data_len was being set to (count - (2 * sizeof(u32))) instead of just
(count - sizeof(u32)). The latter is correct because we skip over the
leading u32 which is our param.type, but we were also incorrectly
subtracting sizeof(u32) on the line where we were actually setting
param.data_len:
param.data_len = count - sizeof(u32);
This meant that for our example event.kernel_software_watchdog with total
length 10 bytes, param.data_len was just 2 prior to this change.
To test, successfully append an event to the log with gsmi sysfs.
This sample event is for a "Kernel Software Watchdog"
> xxd -g 1 event.kernel_software_watchdog
0000000: 01 00 00 00 ad de 06 00 00 00
> cat event.kernel_software_watchdog > /sys/firmware/gsmi/append_to_eventlog
> mosys eventlog list | tail -1
14 | 2012-06-25 10:14:14 | Kernl Event | Software Watchdog
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
[zwisler: updated changelog for 2nd bug fix and upstream]
Signed-off-by: Ross Zwisler <zwisler@google.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
firmware: tegra: Changes for v4.20-rc1
This contains a fix for suspend/resume support for the BPMP found on
Tegra186 and Tegra194.
* tag 'tegra-for-4.20-firmware-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
firmware: tegra: bpmp: Implement suspend/resume support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When returning from a system sleep state, the BPMP driver needs to
reinitialize the IVC channels used to communicate with the BPMP to
restore proper functionality.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
into next/drivers
arm64: zynqmp: SoC CLK changes for v4.20
This patchset adds CCF compliant clock driver for ZynqMP.
Clock driver queries supported clock information from firmware
and regiters pll and output clocks with CCF.
* tag 'zynqmp-soc-clk-for-v4.20' of https://github.com/Xilinx/linux-xlnx:
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/drivers
i.MX drivers change for 4.20, round 2:
- A series from Aisheng Dong to add SCU firmware driver for i.MX8
SoCs. It implements IPC mechanism based on mailbox for message
exchange between AP and SCU firmware, and a set of SCU IPC
service APIs used by clients like i.MX8 power domain and clock
drivers.
* tag 'imx-drivers-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
dt-bindings: arm: fsl: add scu binding doc
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add ZynqMP firmware IOCTL API to control and configure
devices like PLLs, SD, Gem, etc.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add SCU MISC SVC support which provides misc control get/set functions.
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The System Controller Firmware (SCFW) is a low-level system function
which runs on a dedicated Cortex-M core to provide power, clock, and
resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
(QM, QP), and i.MX8QX (QXP, DX).
This patch implements the SCU firmware IPC function and the common
message sending API sc_call_rpc.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/drivers
Qualcomm ARM Based Driver Updates for v4.20
* Refactor of SCM compatibles and clock requirements
* SMEM cleanup
* Add LLCC EDAC driver
* Fixes for GENI clocks and macros
* Fix includes for llcc-slice and smem
* String overflow fixes for APR and wcnss_ctrl
* Fixup for COMPILE_TEST of qcom driver Kconfigs
* Cleanup of Kconfig depends of rpmh, smd_rpm, smsm, and smp2p
* Add SCM dependencies to SPM and rmtfs-mem
* tag 'qcom-drivers-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (38 commits)
soc: qcom: geni: geni_se_clk_freq_match() should always accept multiples
soc: qcom: geni: Don't ignore clk_round_rate() errors in geni_se_clk_tbl_get()
soc: qcom: geni: Make version macros simpler
dt-bindings: firmware: scm: Add MSM8998 and SDM845
firmware: qcom: scm: Refactor clock handling
dt-bindings: firmware: scm: Refactor compatibles and clocks
soc: qcom: smem: a few last cleanups
soc: qcom: smem: verify partition host ids match
soc: qcom: smem: small change in global entry loop
soc: qcom: smem: verify partition offset_free_uncached
soc: qcom: smem: verify partition header size
soc: qcom: smem: introduce qcom_smem_partition_header()
soc: qcom: smem: require order of host ids to match
soc: qcom: smem: verify both host ids in partition header
soc: qcom: smem: small refactor in qcom_smem_enumerate_partitions()
soc: qcom: smem: always ignore partitions with 0 offset or size
soc: qcom: smem: initialize region struct only when successful
soc: qcom: smem: rename variable in qcom_smem_get_global()
drivers: qcom: rpmh-rsc: clear wait_for_compl after use
soc: qcom: rmtfs-mem: Validate that scm is available
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We want those fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/core
Pull EFI updates for v4.20 from Ard Biesheuvel:
- Add support for enlisting the help of the EFI firmware to create memory
reservations that persist across kexec.
- Add page fault handling to the runtime services support code on x86 so
we can gracefully recover from buggy EFI firmware.
- Fix command line handling on x86 for the boot path that omits the stub's
PE/COFF entry point.
- Other assorted fixes.
|
|
Move dcdbas to the more appropriate directory drivers/platform/x86.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Move dell_rbu to the more appropriate directory drivers/platform/x86.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
If the WSMT ACPI table is present and indicates that a fixed communication
buffer should be used, use the firmware-specified buffer instead of
allocating a buffer in memory for communications between the dcdbas driver
and firmare.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The dell_rbu driver takes firmware update payloads and puts them in memory so
the system BIOS can find them after a reboot. This sometimes fails (though
rarely), because the memory containing the payload is in the CPU cache but
never gets written back to main memory before the system is rebooted (CPU
cache contents are lost on reboot).
With this patch, the payload memory will be changed to uncachable to ensure
that the payload is actually in main memory before the system is rebooted.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
into next/drivers
arm64: zynqmp: SoC changes for v4.20
- Adding firmware API for SoC with debugfs interface
Firmware driver communicates to Platform Management Unit (PMU) by using
SMC instructions routed to Arm Trusted Firmware (ATF). Initial version
adds support for base firmware driver with query and clock APIs.
EEMI spec is available here:
https://www.xilinx.com/support/documentation/user_guides/ug1200-eemi-api.pdf
* tag 'zynqmp-soc-for-v4.20-v2' of https://github.com/Xilinx/linux-xlnx:
firmware: xilinx: Add debugfs for query data API
firmware: xilinx: Add debugfs interface
firmware: xilinx: Add clock APIs
firmware: xilinx: Add query data API
firmware: xilinx: Add Zynqmp firmware driver
dt-bindings: firmware: Add bindings for ZynqMP firmware
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Memory accesses performed by UEFI runtime services should be limited to:
- reading/executing from EFI_RUNTIME_SERVICES_CODE memory regions
- reading/writing from/to EFI_RUNTIME_SERVICES_DATA memory regions
- reading/writing by-ref arguments
- reading/writing from/to the stack.
Accesses outside these regions may cause the kernel to hang because the
memory region requested by the firmware isn't mapped in efi_pgd, which
causes a page fault in ring 0 and the kernel fails to handle it, leading
to die(). To save kernel from hanging, add an EFI specific page fault
handler which recovers from such faults by
1. If the efi runtime service is efi_reset_system(), reboot the machine
through BIOS.
2. If the efi runtime service is _not_ efi_reset_system(), then freeze
efi_rts_wq and schedule a new process.
The EFI page fault handler offers us two advantages:
1. Avoid potential hangs caused by buggy firmware.
2. Shout loud that the firmware is buggy and hence is not a kernel bug.
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Suggested-by: Matt Fleming <matt@codeblueprint.co.uk>
Based-on-code-from: Ricardo Neri <ricardo.neri@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
[ardb: clarify commit log]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
After the kernel has booted, if any accesses by firmware causes a page
fault, the efi page fault handler would freeze efi_rts_wq and schedules
a new process. To do this, the efi page fault handler needs
efi_rts_work. Hence, make it accessible.
There will be no race conditions in accessing this structure, because
all the calls to efi runtime services are already serialized.
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Suggested-by: Matt Fleming <matt@codeblueprint.co.uk>
Based-on-code-from: Ricardo Neri <ricardo.neri@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
Add exporting the UEFI runtime service ResetSystem for upper application or test
tools to use.
Signed-off-by: Ivan Hu <ivan.hu@canonical.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
When building with CONFIG_EFI and CONFIG_EFI_STUB on ARM, the libstub
Makefile would use -mno-single-pic-base without checking it was
supported by the compiler. As the ARM (32-bit) clang backend does not
support this flag, the build would fail.
This changes the Makefile to check the compiler's support for
-mno-single-pic-base before using it, similar to c1c386681bd7 ("ARM:
8767/1: add support for building ARM kernel with clang").
Signed-off-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
Add kernel plumbing to reserve memory regions persistently on a EFI
system by adding entries to the MEMRESERVE linked list.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
Installing UEFI configuration tables can only be done before calling
ExitBootServices(), so if we want to use the new MEMRESRVE config table
from the kernel proper, we need to install a dummy entry from the stub.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
In order to allow the OS to reserve memory persistently across a
kexec, introduce a Linux-specific UEFI configuration table that
points to the head of a linked list in memory, allowing each kernel
to add list items describing memory regions that the next kernel
should treat as reserved.
This is useful, e.g., for GICv3 based ARM systems that cannot disable
DMA access to the LPI tables, forcing them to reuse the same memory
region again after a kexec reboot.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
Add debugfs file to query platform specific data from firmware
using debugfs interface.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Firmware-debug provides debugfs interface to all APIs.
Debugfs can be used to call firmware APIs with required
parameters.
Usage:
* Calling firmware API through debugfs:
# echo "<api-name> <arg1> .. <argn>" > /sys/.../zynqmp-firmware/pm
* Read output of last called firmware API:
# cat /sys/.../zynqmp-firmware/pm
Refer ug1200 for more information on these APIs:
* https://www.xilinx.com/support/documentation/user_guides/ug1200-eemi-api.pdf
Add basic debugfs file to get API version.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add clock APIs to control clocks through firmware
interface.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add ZynqMP firmware query data API to query platform
specific information(clocks, pins) from firmware.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch is adding communication layer with firmware.
Firmware driver provides an interface to firmware APIs.
Interface APIs can be used by any driver to communicate to
PMUFW(Platform Management Unit). All requests go through ATF.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
