summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/amd/display/dc
AgeCommit message (Collapse)Author
2018-10-09drm/amd/display: HLK Periodic Frame Notification test failedMurton Liu
[Why] Due to a small pre-fetch window, the active vline timing is a couple of lines off when compared to what it should be. [How] Changed the calculation for the start vline to account for this window. Signed-off-by: Murton Liu <murton.liu@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: fix Interlace video timing.Charlene Liu
[Description] interlace mode shows wrong vertical timing. Interface timing in Edid is half vertical timing as progressive timing. driver doubled the vertical timing in edid_paser, no need to double in optc again. Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: fix memory leak in resource poolsJun Lei
[why] ddc engines were recently changed to be independently tracked from pipe count. the change was reflected in resource constructor but not in destructor. this manifests as a memory leak when pipe harvesting is enabled, since not all constructed ddc engines are freed [how] make destructor symmetric with constructor for all dcX_resource Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: dc 3.1.68Tony Cheng
Signed-off-by: Tony Cheng <tony.cheng@amd.com> Reviewed-by: Steven Chiu <Steven.Chiu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: WA for DF keeps awake after S0i3.Yongqiang Sun
[Why] DF keeps awake after S0i3 resume due to DRAM_STATE_CNTL is set by bios command table during dcn init_hw. [How] As a work around, check STATE_CNTL status before init_hw, if it is 0 before init_hw and set to 1 after init_hw, change it to 0. Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: clean up encoding checksEric Yang
[Why] All ASICS we support has YCbCr support, so the check is unnecessary, the currently logic in validate output also returns true all the time, so the unneccessary logic is removed Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: block DP YCbCr420 modesEric Yang
[why] Currently not supported, will black screen when set. [How] Fail validate timing helper for those modes. Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Add function to fetch clock requirementsEryk Brol
Also add dram clock to clocks struct, for systems that uses them. Signed-off-by: Eryk Brol <eryk.brol@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Calculate swizzle mode using bpp during validationSu Sung Chung
[Why] Previously bandwidth validation was failing because swizzle mode was not initialized during plane_state allocation. The swizzle mode was calculated using pixed format which is how swizzle mode is initially calculated in addrlib. [How] * Set default swizzle mode for validation to DC_SW_UNKNOWN * Created new function in dcn10_assign_swizzle_mode which sets the plane swizzle mode based on selected pixed format * Added the call of assign_swizzle_mode into dc_validate_global_state * Set failsafe swizzle mode back to DC_SW_LINEAR Signed-off-by: Su Sung Chung <Su.Chung@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: fix 4K stereo screen flash issueCharlene Liu
[Why] HDMI_scramber is not enabled for pixel rate >340Mhz. [How] Calculate the phy clock to include the Hw frame packing factor. Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Add DC build_id to determine build typeJun Lei
[why] Sometimes there are indications that the incorrect driver is being loaded in automated tests. This change adds the ability for builds to be tagged with a string, and picked up by the test infrastructure. [how] dc.c will allocate const for build id, which is init-ed with default value, indicating production build. For test builds, build server will find/replace this value. The test machine will then verify this value. Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-04BackMerge v4.19-rc6 into drm-nextDave Airlie
I have some pulls based on rc6, and I prefer to have an explicit backmerge. Signed-off-by: Dave Airlie <airlied@redhat.com>
2018-09-27drm/amd/display: Fix Edid emulation for linuxBhawanpreet Lakha
[Why] EDID emulation didn't work properly for linux, as we stop programming if nothing is connected physically. [How] We get a flag from DRM when we want to do edid emulation. We check if this flag is true and nothing is connected physically, if so we only program the front end using VIRTUAL_SIGNAL. Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-27drm/amd/display: Fix Vega10 lightup on S3 resumeRoman Li
[Why] There have been a few reports of Vega10 display remaining blank after S3 resume. The regression is caused by workaround for mode change on Vega10 - skip set_bandwidth if stream count is 0. As a result we skipped dispclk reset on suspend, thus on resume we may skip the clock update assuming it hasn't been changed. On some systems it causes display blank or 'out of range'. [How] Revert "drm/amd/display: Fix Vega10 black screen after mode change" Verified that it hadn't cause mode change regression. Signed-off-by: Roman Li <Roman.Li@amd.com> Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-26drm/amd/display: Raise dispclk value for dce120 by 15%Nicholas Kazlauskas
[Why] The DISPCLK value was previously requested to be 15% higher for all ASICs that went through the dce110 bandwidth code path. As part of a refactoring of dce_clocks and the dce110 set bandwidth codepath this was removed for power saving considerations. That change caused display corruption under certain hardware configurations with Vega10. [How] The 15% DISPCLK increase is brought back but only on dce110 for now. This is should be a temporary workaround until the root cause is sorted out for why this occurs on Vega (or other ASICs, if reported). Tested-by: Nick Sarnie <sarnex@gentoo.org> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-26drm/amd/display: fix gamma not being appliedSivapiriyanKumarasamy
[WHY] Previously night light forced a full update by applying a transfer function update regardless of if it was changed. This logic was removed, Now gamma surface updates are only applied when there is also a plane info update, this does not work in cases such as using the night light slider. [HOW] When moving the night light slider we will perform a full update if the gamma has changed and there is a surface, even when the surface has not changed. Also get stream updates in setgamma prior to update planes and stream. Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-26drm/amd/display: dc 3.1.67Tony Cheng
Signed-off-by: Tony Cheng <tony.cheng@amd.com> Reviewed-by: Steven Chiu <Steven.Chiu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-26drm/amd/display: program v_update and v_ready with proper fieldSu Sung Chung
[WHY] There are two different variables used to calculate v_update and v_ready, one for validation and the other for performance parameter calculation. Before the variable for validation was used which caused underflow on 1080edp with vsr enabled [HOW] program v_update and v_ready with the variables for performance parameter calculation Signed-off-by: Su Sung Chung <su.chung@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-26drm/amd/display: add pp_smu NULL pointer checkCharlene Liu
add pp_smu NULL ptr check Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-26drm/amd/display: use proper pipe_ctx indexSamson Tam
Use link->link_index as index to pipe_ctx[] to get proper link information instead of using index 0 to avoid potential miss matches. Signed-off-by: Samson Tam <Samson.Tam@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-26drm/amd/display: Refactor FPGA-specific link setupNikola Cornij
FPGA doesn't program backend, so we don't need certain link settings (audio stream for example). Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-14drm/amd/display: add query HPD interface.Chiawen Huang
[Why] current dc_link_detect function is not only detection but also update some link data. [How] added a pure get HPD state function. Signed-off-by: Chiawen Huang <chiawen.huang@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-14drm/amd/display: dc 3.1.66Tony Cheng
Signed-off-by: Tony Cheng <tony.cheng@amd.com> Reviewed-by: Steven Chiu <Steven.Chiu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-14drm/amd/display: add aux i2c event log.Chiawen Huang
[Why] support i2c transition event log [How] refined aux REQ and REP events in aux flow. commented REQ and REP events in i2c flow. note: i2c event log is currently commented out. more work is required to find an portocol parser to and generate event for the parser Signed-off-by: Chiawen Huang <chiawen.huang@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-14drm/amd/display: stop using switch for different CS revisionsDmytro Laktyushkin
Clock sources currently have support for asic specific function pointers. But actual separation into functions was never performed, leaving us with giant functions that rely on switch. This change creates separate functions, removing switch use. Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-14drm/amd/display: Fix 3D stereo issues.Charlene Liu
We were not providing the correct pixel clocks to DML for marks calculation. Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-14drm/amd/display: Add Raven2 definitions in dcBhawanpreet Lakha
Add Raven2 definitions in the dc code Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: Add invariant support instrumentation in driverJun Lei
Existing debug dump are all invariant, new “low 32-bit of address” dump is not invariant Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: clean code for transition event log.Chiawen Huang
[Why] There are same purpose transition events. [How] remove the redundant event log. Signed-off-by: Chiawen Huang <chiawen.huang@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: use link type to decide stream enc acquisitionEric Yang
[Why] Virtual sink is used when set mode happens on a disconnected display to allow the mode set to proceed. This did not work with MST because the logic for acquiring stream encoder uses stream signal to determine the special handling is required, and stream signal is virtual instead of DP in this case. [How] Use link type to decide instead. Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: dc 3.1.65Tony Cheng
Signed-off-by: Tony Cheng <tony.cheng@amd.com> Reviewed-by: Steven Chiu <Steven.Chiu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: Reorder resource_pool to put i2c with auxDavid Francis
[Why] The i2c and aux engines are similar, and should be placed next to eachother for readability [How] Reorder the elements of the resource_pool struct Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: num of sw i2c/aux engines less than num of connectorsHersen Wu
[why] AMD Stoney reference board, there are only 2 pipes (not include underlay), and 3 connectors. resource creation, only 2 I2C/AUX engines are created. Within dc_link_aux_transfer, when pin_data_en =2, refer to enengines[ddc_pin->pin_data->en] = NULL. NULL point is referred later causing system crash. [how] each asic design has fixed number of ddc engines at hw side. for each ddc engine, create its i2x/aux engine at sw side. Signed-off-by: Hersen Wu <hersenxs.wu@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: add aux transition event log.Chiawen Huang
[Why] Enhance aux transition debugging information. [How] Added Aux request and reply event log. Signed-off-by: Chiawen Huang <chiawen.huang@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: add disconnect_delay to dc_panel_patchDerek Lai
Some display need disconnect delay. Adding this parameter for future use Signed-off-by: Derek Lai <Derek.Lai@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: remove unused clk_src codeDmytro Laktyushkin
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: remove dead dc vbios codeDmytro Laktyushkin
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: Add driver-side parsing for CMJun Lei
Although 4 unique register values exist for gamma modes, two are actually the same (the two RAMs) It’s not possible for caller to understand this HW specific behavior, so some parsing is necessary in driver Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: Fix DAL217 tests modify DTN logs for other testsGary Kattan
[Why]Update Code to get DTN golden log check to pass for tests run after DAL217 tests. [How]Change how dcn10_log_hw_state function prints HW state info (CM_GAMUT_REMAP_Cx_Cx registers) when GAMUT REMAP is in bypass mode. Signed-off-by: Gary Kattan <gary.kattan@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-09-10drm/amd/display: dc 3.1.64Tony Cheng
Signed-off-by: Tony Cheng <tony.cheng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Flatten unnecessary i2c functionsDavid Francis
[Why] The dce_i2c_hw code contained four funtcions that were only called in one place and did not have a clearly delineated purpose. [How] Inline these functions, keeping the same functionality. This is not a functional change. The functions disable_i2c_hw_engine and release_engine_dce_hw were pulled into their respective callers. The most interesting part of this change is the acquire functions. dce_i2c_hw_engine_acquire_engine was pulled into dce_i2c_engine_acquire_hw, and dce_i2c_engine_acquire_hw was pulled into acquire_i2c_hw_engine. Some notes to show that this change is not functional: -Failure conditions in any function resulted in a cascade of calls that ended in a 'return NULL'. Those are replaced with a direct 'return NULL'. -The variable result is the one from dce_i2c_hw_engine_acquire_engine. The boolean result used as part of return logic was removed. -As the second half of dce_i2c_hw_engine_acquire_engine is only executed if that function is returning true and therefore exiting the do-while loop in dce_i2c_engine_acquire_hw, those lines were moved outside of the loop. Signed-off-by: David Francis <David.Francis@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: support 48 MHZ refclk offEric Yang
[Why] On PCO and up, whenever SMU receive message to indicate active display count = 0. SMU will turn off 48MHZ TMDP reference clock by writing to 1 TMDP_48M_Refclk_Driver_PWDN. Once this clock is off, no PHY register will respond to register access. This means our current sequence of notifying display count along with requesting clock will cause driver to hang when accessing PHY registers after displays count goes to 0. [How] Separate the PPSMC_MSG_SetDisplayCount message from the SMU messages that request clocks, have display own sequencing of this message so that we can send it at the appropriate time. Do not redundantly power off HW when entering S3, S4, since display should already be called to disable all streams. And ASIC soon be powered down. Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Remove redundant i2c structsDavid Francis
[Why] The i2c code contains two structs that contain the same information as i2c_payload [How] Replace references to those structs with references to i2c_payload dce_i2c_transaction_request->status was written to but never read, so all references to it are removed Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Support reading hw state from debugfs fileNicholas Kazlauskas
[Why] Logging hardware state can be done by triggering a write to the debugfs file. It would also be useful to be able to read the hardware state from the debugfs file to be able to generate a clean log without timestamps. [How] Usage: cat /sys/kernel/debug/dri/0/amdgpu_dm_dtn_log Threading is an obvious concern when dealing with multiple debugfs operations and blocking on global state in dm or dc seems unfavorable. Adding an extra parameter for the debugfs log context state is the implementation done here. Existing code that made use of DTN_INFO and its associated macros needed to be refactored to support this. We don't know the size of the log in advance so it reallocates the log string dynamically. Once the log has been generated it's copied into the user supplied buffer for the debugfs. This allows for seeking support but it's worth nothing that unlike triggering output via dmesg the hardware state might change in-between reads if your buffer size is too small. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Fix memory leak caused by missed dc_sink_releaseSivapiriyanKumarasamy
[Why] There is currently an intermittent hang from a memory leak in DTN stress testing. It is caused by unfreed memory during driver disable. [How] Do a dc_sink_release in the case that skips it incorrectly. Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: eliminate long wait between register polls on MaximusKen Chalmers
[Why] Now that we "scale" time delays correctly on Maximus (as of diags svn r170115), the forced "35 ms" wait time now becomes 35 ms * 500 = 17.5 seconds, which is far too long. Even having to repeat polling a register once causes excessive delays on Maximus. [How] Just use the regular wait time passed to the generic_reg_wait() function. This is sufficient for Maximus now, and it also means that there's one less "Maximus-only" code path in DAL. Also disable the "REG_WAIT taking a while:" message on Maximus, since things do take a while longer there and 1-2ms delays are not uncommon (and nothing to worry about). Signed-off-by: Ken Chalmers <ken.chalmers@amd.com> Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: dc 3.1.63Tony Cheng
Signed-off-by: Tony Cheng <tony.cheng@amd.com> Reviewed-by: Steven Chiu <Steven.Chiu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Eliminate i2c hw function pointersDavid Francis
[Why] The function pointers of the dce_i2c_hw struct were never accessed from outside dce_i2c_hw.c and had only one version. As function pointers take up space and make debugging difficult, and they are not needed in this case, they should be removed. [How] Remove the dce_i2c_hw_funcs struct and make static all functions that were previously a part of it. Reorder the functions in dce_i2c_hw.c. Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amd/display: Fix memory leak caused by missed dc_sink_releaseSivapiriyanKumarasamy
[Why] There is currently an intermittent hang from a memory leak in DTN stress testing. It is caused by unfreed memory during driver disable. [How] Do a dc_sink_release in the case that skips it incorrectly. Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-08-27drm/amdgpu/display: add support for LVDS (v5)Alex Deucher
This adds support for LVDS displays. v2: add support for spread spectrum, sink detect v3: clean up enable_lvds_output v4: fix up link_detect v5: remove assert on 888 format Bug: https://bugs.freedesktop.org/show_bug.cgi?id=105880 Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
generated by cgit v1.2.3-70-g09d2 (git 2.48.1) at 2025-09-25 00:39:11 +0000