Age | Commit message (Collapse) | Author |
|
[Why]
Request from PMFW to use GART for clock table transfer tables as
framebuffer is being deprecated on APU.
[How]
Switch over to GART via the allocation flag.
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
translate_by_source need not be set for DCN401 onwards since cursor
cursor composition comes after scaler in the hardware pipeline.
Hence offset calculation has been reworked, and this setting is not
necessary to be enabled anymore.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Remove coverity issues that were originally ignored.
[HOW]
Ran coverity locally on driver, used output report to find existing
coverity issues, resolved them
Reviewed-by: Nicholas Choi <nicholas.choi@amd.com>
Signed-off-by: Daniel Sa <Daniel.Sa@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Prefetch calculations did not guarantee that bandwidth required in
mode support was less than mode programming which can cause failures.
[HOW]
Fix bandwidth calculations to assume fixed times for OTO schedule,
and choose which schedule to use based on time to fetch pixel data.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
Before every full update we must wait for all pending updates to be
cleared - this is particularly important for minimal transitions
because if we don't wait for pending cleared, it will be as if
there was no minimal transition at all. In OTG we must read 3 different
status registers for pending cleared, one specifically for OTG updates,
one specifically for OPTC updates, and the last for surface related
updates
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
post_divider_value should not be 0.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ahmed, Muhammad <Ahmed.Ahmed@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
Skipping clock updates is not a hard requirement for overclocking
and only an optimization. Remove the skip as this can cause issues
for FAMS transitions during the overclock sequence. If FAMS
is enabled we must disable UCLK switch on any full update (which
requires update clocks to be called).
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Idle power states (IPS) describe levels of power-gating within DCN. DM
and DC is responsible for ensuring that we are out of IPS before any DCN
programming happens. Any DCN programming while we're in IPS leads to
undefined behavior (mostly hangs).
Because IPS intersects with all display features, the ability to disable
IPS by default while ironing out the known issues is desired. However,
disabing it completely will cause important features such as s0ix entry
to fail.
Therefore, more granular IPS debug flags are desired.
[How]
Extend the dc debug mask bits to include the available list of IPS
debug flags.
All the flags should work as documented, with the exception of
IPS_DISABLE_DYNAMIC. It requires dm changes which will be done in
later changes.
v2: enable docs and fix docstring format
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Print the index for the profiles.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3543
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No change in functionality for the current code, but we
need to set the index properly before changing it if we
ever use a non-0 index.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The kernel doc says you need to select manual mode to
adjust this, but the code only allows you to adjust it when
manual mode is not selected. Remove the manual mode check.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-6.12-2024-08-26:
amdgpu:
- SDMA devcoredump support
- DCN 4.0.1 updates
- DC SUBVP fixes
- Refactor OPP in DC
- Refactor MMHUBBUB in DC
- DC DML 2.1 updates
- DC FAMS2 updates
- RAS updates
- GFX12 updates
- VCN 4.0.3 updates
- JPEG 4.0.3 updates
- Enable wave kill (soft recovery) for compute queues
- Clean up CP error interrupt handling
- Enable CP bad opcode interrupts
- VCN 4.x fixes
- VCN 5.x fixes
- GPU reset fixes
- Fix vbios embedded EDID size handling
- SMU 14.x updates
- Misc code cleanups and spelling fixes
- VCN devcoredump support
- ISP MFD i2c support
- DC vblank fixes
- GFX 12 fixes
- PSR fixes
- Convert vbios embedded EDID to drm_edid
- DCN 3.5 updates
- DMCUB updates
- Cursor fixes
- Overdrive support for SMU 14.x
- GFX CP padding optimizations
- DCC fixes
- DSC fixes
- Preliminary per queue reset infrastructure
- Initial per queue reset support for GFX 9
- Initial per queue reset support for GFX 7, 8
- DCN 3.2 fixes
- DP MST fixes
- SR-IOV fixes
- GFX 9.4.3/4 devcoredump support
- Add process isolation framework
- Enable process isolation support for GFX 9.4.3/4
- Take IOMMU remapping into account for P2P DMA checks
amdkfd:
- CRIU fixes
- Improved input validation for user queues
- HMM fix
- Enable process isolation support for GFX 9.4.3/4
- Initial per queue reset support for GFX 9
- Allow users to target recommended SDMA engines
radeon:
- remove .load and drm_dev_alloc
- Fix vbios embedded EDID size handling
- Convert vbios embedded EDID to drm_edid
- Use GEM references instead of TTM
- r100 cp init cleanup
- Fix potential overflows in evergreen CS offset tracking
UAPI:
- KFD support for targetting queues on recommended SDMA engines
Proposed userspace:
https://github.com/ROCm/ROCR-Runtime/commit/2f588a24065f41c208c3701945e20be746d8faf7
https://github.com/ROCm/ROCR-Runtime/commit/eb30a5bbc7719c6ffcf2d2dd2878bc53a47b3f30
drm/buddy:
- Add start address support for trim function
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240826201528.55307-1-alexander.deucher@amd.com
|
|
amdgpu pr conconflicts due to patches cherry-picked to -fixes, I might
as well catch up with a backmerge and handle them all. Plus both misc
and intel maintainers asked for a backmerge anyway.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Ideally, we want to drop the legacy vblank enable for older ASICs. This
should be possible now, since we can now specify how many frames we need
to wait before disabling vblanking instead of being forced to either
choose between no delay (which can still be buggy) and
drm_vblank_offdelay (which is much longer by default than is required on
AMD hardware).
Suggested-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240822161856.174600-4-hamza.mahfooz@amd.com
|
|
Ideally, we want to enable immediate vblank disable, when possible and
we should be able to do so on DCN35+, if PSR isn't supported by a given
CRTC.
Suggested-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240822161856.174600-3-hamza.mahfooz@amd.com
|
|
Hook up drm_crtc_vblank_on_config() in amdgpu_dm. So, that we can enable
PSR and other static screen optimizations more quickly, while avoiding
stuttering issues that are accompanied by the following dmesg error:
[drm:dc_dmub_srv_wait_idle [amdgpu]] *ERROR* Error waiting for DMUB idle: status=3
This also allows us to mimic how vblanking is handled by the Windows
amdgpu driver. Specifically, we wait two idle frames before disabling
the vblank timer there.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240822161856.174600-2-hamza.mahfooz@amd.com
|
|
Drop unsupported features on smu v14_0_2.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When app unmap vm ranges(munmap) kfd/svm starts drain pending page fault and
not handle any incoming pages fault of this process until a deferred work item
got executed by default system wq. The time period of "not handle page fault"
can be long and is unpredicable. That is advese to kfd performance on page
faults recovery.
This patch uses time stamp of incoming page fault to decide to drop or recover
page fault. When app unmap vm ranges kfd records each gpu device's ih ring
current time stamp. These time stamps are used at kfd page fault recovery
routine.
Any page fault happened on unmapped ranges after unmap events is application
bug that accesses vm range after unmap. It is not driver work to cover that.
By using time stamp of page fault do not need drain page faults at deferred
work. So, the time period that kfd does not handle page faults is reduced
and can be controlled.
Signed-off-by: Xiaogang.Chen <Xiaogang.Chen@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add p2s table support for a new revision of SMUv13.0.6.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add gc_info table v1.3 for IP discovery.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Instead of using state->fb->obj[0] directly, get object from framebuffer
by calling drm_gem_fb_get_obj() and return error code when object is
null to avoid using null object of framebuffer.
Fixes: 5d945cbcd4b1 ("drm/amd/display: Create a file dedicated to planes")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add list empty check to avoid null pointer issues in some corner cases.
- list_for_each_entry_safe()
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The sparse tool complains as follows:
drivers/gpu/drm/amd/amdgpu/../display/dc/dsc/dcn401/dcn401_dsc.c:30:24: warning:
symbol 'dcn401_dsc_funcs' was not declared. Should it be static?
This symbol is not used outside of dcn401_dsc.c, so marks it static.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The sparse tool complains as follows:
drivers/gpu/drm/amd/amdgpu/../display/dc/hubp/dcn35/dcn35_hubp.c:191:19: warning:
symbol 'dcn35_hubp_funcs' was not declared. Should it be static?
This symbol is not used outside of dcn35_hubp.c, so marks it static.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The sparse tool complains as follows:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/dml21/src/dml2_core/dml2_core_dcn4.c:12:28: warning:
symbol 'core_dcn4_ip_caps_base' was not declared. Should it be static?
This symbol is not used outside of dcn35_hubp.c, so marks it static.
And do not want to change it, so mark it const.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The sparse tool complains as follows:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/dml21/src/dml2_core/dml2_core_dcn4_calcs.c:6853:56: warning:
symbol 'core_dcn4_g6_temp_read_blackout_table' was not declared. Should it be static?
This symbol is not used outside of dml2_core_dcn4_calcs.c, so marks it static.
And not want to change it, so mark it const.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This needs to be set to 1 to avoid a potential deadlock in
the GC 10.x and newer. On GC 9.x and older, this needs
to be set to 0. This can lead to hangs in some mixed
graphics and compute workloads.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3575
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Driver switches to interrupt source id to identify
utcl2 poison event. polling interface is not needed.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
when trying to enable p2p the amdgpu_device_is_peer_accessible()
checks the condition where address_mask overlaps the aper_base
and hence returns 0, due to which the p2p disables for this platform
IOMMU should remap the BAR addresses so the device can access
them. Hence check if peer_adev is remapping DMA
v5: (Felix, Alex)
- fixing comment as per Alex feedback
- refactor code as per Felix
v4: (Alex)
- fix the comment and description
v3:
- remove iommu_remap variable
v2: (Alex)
- Fix as per review comments
- add new function amdgpu_device_check_iommu_remap to check if iommu
remap
Signed-off-by: Rahul Jain <Rahul.Jain@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
update message interface for smu v14.0.2/3
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Not supported.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Traditional utcl2 fault_status polling does not
work in SRIOV environment. The polling of fault
status register from guest side will be dropped
by hardware.
Driver should switch to check utcl2 interrupt
source id to identify utcl2 poison event. It is
set to 1 when poisoned data interrupts are
signaled.
v2: drop the unused local variable (Tao)
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The driver needs to wait for the on board firmware
to finish its initialization before probing the card.
Commit 959056982a9b ("drm/amdgpu: Fix discovery initialization failure during pci rescan")
switched from using msleep() to using usleep_range() which
seems to have caused init failures on some navi1x boards. Switch
back to msleep().
Fixes: 959056982a9b ("drm/amdgpu: Fix discovery initialization failure during pci rescan")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3559
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3500
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Ma Jun <Jun.Ma2@amd.com>
(cherry picked from commit c69b07f7bbc905022491c45097923d3487479529)
Cc: stable@vger.kernel.org # 6.10.x
|
|
Add TA binary size validation to avoid OOB write.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit c0a04e3570d72aaf090962156ad085e37c62e442)
Cc: stable@vger.kernel.org
|
|
The workaround seems to cause stability issues on other
SDMA 5.2.x IPs.
Fixes: a03ebf116303 ("drm/amdgpu/sdma5.2: Update wptr registers as well as doorbell")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3556
Acked-by: Ruijing Dong <ruijing.dong@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2dc3851ef7d9c5439ea8e9623fc36878f3b40649)
Cc: stable@vger.kernel.org
|
|
Skip rlc firmware validation to ignore firmware header size mismatch issues.
This restores the workaround added in
commit 849e133c973c ("drm/amdgpu: Fix the null pointer when load rlc firmware")
Fixes: 3af2c80ae2f5 ("drm/amdgpu: refine gfx10 firmware loading")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3551
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 89ec85d16eb8110d88c273d1d34f1fe5a70ba8cc)
|
|
Otherwise we can fail to drop the software mutex when
we fail to take the hardware mutex.
Fixes: 76acba7b7f12 ("drm/amdgpu/gfx11: add a mutex for the gfx semaphore")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This resolves the dereference null return value warning
reported by Coverity.
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Jesse Zhang <jesse.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
when use cpu to do page table update under sriov runtime, since mmio
access is blocked, kiq has to be used to flush hdp.
change WREG32_NO_KIQ to WREG32 to allow kiq.
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The driver needs to wait for the on board firmware
to finish its initialization before probing the card.
Commit 959056982a9b ("drm/amdgpu: Fix discovery initialization failure during pci rescan")
switched from using msleep() to using usleep_range() which
seems to have caused init failures on some navi1x boards. Switch
back to msleep().
Fixes: 959056982a9b ("drm/amdgpu: Fix discovery initialization failure during pci rescan")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3559
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3500
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Ma Jun <Jun.Ma2@amd.com>
|
|
- Various DML 2.1 fixes
- Fix module unload
- Fix construct_phy with MXM connector
- Support UHBR10 link rate on eDP
- Revert updated DCCG wrappers
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why and How]
DML2.1 reintegration for several fixes and updates to the DML
code.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Roman Li <roman.li@amd
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Flexible endpoints use DIGs from available inflexible endpoints,
so only the encoders of inflexible links need to be freed.
Otherwise, a double free issue may occur when unloading the
amdgpu module.
[ 279.190523] RIP: 0010:__slab_free+0x152/0x2f0
[ 279.190577] Call Trace:
[ 279.190580] <TASK>
[ 279.190582] ? show_regs+0x69/0x80
[ 279.190590] ? die+0x3b/0x90
[ 279.190595] ? do_trap+0xc8/0xe0
[ 279.190601] ? do_error_trap+0x73/0xa0
[ 279.190605] ? __slab_free+0x152/0x2f0
[ 279.190609] ? exc_invalid_op+0x56/0x70
[ 279.190616] ? __slab_free+0x152/0x2f0
[ 279.190642] ? asm_exc_invalid_op+0x1f/0x30
[ 279.190648] ? dcn10_link_encoder_destroy+0x19/0x30 [amdgpu]
[ 279.191096] ? __slab_free+0x152/0x2f0
[ 279.191102] ? dcn10_link_encoder_destroy+0x19/0x30 [amdgpu]
[ 279.191469] kfree+0x260/0x2b0
[ 279.191474] dcn10_link_encoder_destroy+0x19/0x30 [amdgpu]
[ 279.191821] link_destroy+0xd7/0x130 [amdgpu]
[ 279.192248] dc_destruct+0x90/0x270 [amdgpu]
[ 279.192666] dc_destroy+0x19/0x40 [amdgpu]
[ 279.193020] amdgpu_dm_fini+0x16e/0x200 [amdgpu]
[ 279.193432] dm_hw_fini+0x26/0x40 [amdgpu]
[ 279.193795] amdgpu_device_fini_hw+0x24c/0x400 [amdgpu]
[ 279.194108] amdgpu_driver_unload_kms+0x4f/0x70 [amdgpu]
[ 279.194436] amdgpu_pci_remove+0x40/0x80 [amdgpu]
[ 279.194632] pci_device_remove+0x3a/0xa0
[ 279.194638] device_remove+0x40/0x70
[ 279.194642] device_release_driver_internal+0x1ad/0x210
[ 279.194647] driver_detach+0x4e/0xa0
[ 279.194650] bus_remove_driver+0x6f/0xf0
[ 279.194653] driver_unregister+0x33/0x60
[ 279.194657] pci_unregister_driver+0x44/0x90
[ 279.194662] amdgpu_exit+0x19/0x1f0 [amdgpu]
[ 279.194939] __do_sys_delete_module.isra.0+0x198/0x2f0
[ 279.194946] __x64_sys_delete_module+0x16/0x20
[ 279.194950] do_syscall_64+0x58/0x120
[ 279.194954] entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 279.194980] </TASK>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Causes hard hangs when resuming after display off on extended/duplicate
modes
[How]
Set the min dispclk to 50Mhz for DCN35
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Susanto <Nicholas.Susanto@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why/How]
The call to construct_phy will fail in cases where connector type is
MXM, and the dc_link won't be properly created/initialized.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Supporting UHBR10 link rate on eDP leverages
the existing DP2.0 code but need to add some small
adjustments in code.
[how]
Acknowledge the given DPCD caps for UHBR10
link rate support and allow DP2.0 programming
sequence and link training for eDP.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
DCN4 Cursor has separate degamma block and should always
do Cursor degamma for Cursor color modes.
Reviewed-by: Chris Park <chris.park@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
eDP 2.0 is introducing support for UHBR link rates, however current eDP ILR
link optimization does not account for UHBR capabilities.
Either UHBR capabilities will be provided via the same 128b/132b rate DPCD caps
that are currently used on DP2.1, or Table 4-13 may be updated to include UHBR
rates.
[HOW]
Add extra Supported Link Rates table translations for UHBR10/13.5/20.
Update eDP link setting optimization search to be aware of 128b/132b DPCD
rate caps in order to unblock UHBR on panels with Supported Link Rates table.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Removing redundant condition.
Reviewed-by: Hansen Dsouza <Hansen.Dsouza@amd.com>
Signed-off-by: Nicholas Susanto <Nicholas.Susanto@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
when removing the amdgpu module and reinserting it, a call trace is
triggered:
[ 334.230602] RIP: 0010:hubbub2_get_dchub_ref_freq+0xbb/0xe0 [amdgpu]
[ 334.230807] Code: 25 28 00 00 00 75 3c 48 8d 65 f0 5b 41 5c 5d 31 c0 31 d2 31 c9 31 f6 31 ff 45 31 c0 45 31 c9 45 31 d2 45 31 db e9 55 a1 ca de <0f> 0b eb c6 0f 0b eb c2 d1 eb 8d 83 c0 63 ff ff 3d 20 4e 00 00 76
[ 334.230809] RSP: 0018:ffffbc8b823fb540 EFLAGS: 00010246
[ 334.230811] RAX: 0000000000001000 RBX: 00000000000186a0 RCX: 0000000000000000
[ 334.230812] RDX: ffffbc8b823fb544 RSI: 0000000000000000 RDI: 0000000000000000
[ 334.230813] RBP: ffffbc8b823fb560 R08: 0000000000000000 R09: 0000000000000000
[ 334.230814] R10: 0000000000000000 R11: 000000000000000f R12: ffff9e644f1f2bb0
[ 334.230815] R13: ffff9e6451361300 R14: 0000000000000000 R15: ffff9e6452c00000
[ 334.230816] FS: 00007af7c8519000(0000) GS:ffff9e737dd00000(0000) knlGS:0000000000000000
[ 334.230817] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 334.230818] CR2: 0000703576b9cbd0 CR3: 00000001095a2000 CR4: 0000000000750ee0
[ 334.230819] PKRU: 55555554
[ 334.230820] Call Trace:
[ 334.230822] <TASK>
[ 334.230824] ? show_regs+0x6d/0x80
[ 334.230828] ? __warn+0x89/0x160
[ 334.230832] ? hubbub2_get_dchub_ref_freq+0xbb/0xe0 [amdgpu]
[ 334.231024] ? report_bug+0x17e/0x1b0
[ 334.231028] ? handle_bug+0x46/0x90
[ 334.231030] ? exc_invalid_op+0x18/0x80
[ 334.231032] ? asm_exc_invalid_op+0x1b/0x20
[ 334.231036] ? hubbub2_get_dchub_ref_freq+0xbb/0xe0 [amdgpu]
[ 334.231217] dc_create_resource_pool+0xfd/0x320 [amdgpu]
[ 334.231408] dc_create+0x256/0x700 [amdgpu]
[ 334.231588] ? srso_alias_return_thunk+0x5/0x7f
[ 334.231590] ? dmi_matches+0xa0/0x230
[ 334.231594] amdgpu_dm_init+0x28c/0x25f0 [amdgpu]
[ 334.231791] ? prb_read_valid+0x1c/0x30
[ 334.231795] ? __irq_work_queue_local+0x43/0xf0
[ 334.231798] ? srso_alias_return_thunk+0x5/0x7f
[ 334.231800] ? irq_work_queue+0x2f/0x70
[ 334.231802] ? srso_alias_return_thunk+0x5/0x7f
[ 334.231803] ? __wake_up_klogd.part.0+0x40/0x70
[ 334.231805] ? srso_alias_return_thunk+0x5/0x7f
[ 334.231807] ? vprintk_emit+0xd9/0x210
[ 334.231809] ? set_dev_info+0x130/0x1c0
[ 334.231812] ? srso_alias_return_thunk+0x5/0x7f
[ 334.231813] ? dev_printk_emit+0xa1/0xe0
[ 334.231819] dm_hw_init+0x14/0x30 [amdgpu]
[ 334.231993] amdgpu_device_init+0x23c7/0x2fc0 [amdgpu]
[ 334.232134] ? pci_read_config_word+0x25/0x50
[ 334.232139] amdgpu_driver_load_kms+0x1a/0xd0 [amdgpu]
[ 334.232284] amdgpu_pci_probe+0x1f9/0x620 [amdgpu]
On DCN401, get_dchub_ref_freq() hook is called before init_hw() hook.
Hence, it is expected to trigger an assert. Remove the extraneous call
to get_dchub_ref_freq() to suppress the call trace
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|