| Age | Commit message (Collapse) | Author |
|---|
|
Fix a couple of spelling typos.
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Doing this allows us to split it for diffrent asics. This design will
be helpful for future Asciis.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Previously SMU was giving us 0s for the clock table. Now they have valid
clock table. We should use theirs. Also, need to send SMU watermark
ranges for selecting optimal watermarks.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Without a check for virtual links, every link's DIG was getting
checked for enabled or disabled. If link was virtual, since it
did not have a DIG, this would cause issues.
[HOW]
Skip DIG Enable check if link is virtual and add virtual link to
to display count.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
HDMI 2.0 requires scrambling under specific conditions. We refer to
stream property LTE_340MCSC_SCRAMBLE to determine whether en/dis
scrambling.
While creating stream for sink, we setup LTE_340MCSC_SCRAMBLE by
referring to edid_caps. However, dm_helpers_parse_edid_caps()
doesn't construct HDMI Forum block data for edid_caps.
Moreover, fill_stream_properties_from_drm_display_mode() aslo
unconsciously clear the LTE_340MCSC_SCRAMBLE flag.
[How]
Drm already provides drm_display_info to refer HDMI Forum vsdb info.
Set stream LTE_340MCSC_SCRAMBLE by drm_display_info and remove
memset in fill_stream_properties_from_drm_display_mode()
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
During detection:
function: get_active_converter_info populates link->dpcd_caps.dongle_caps
only when dpcd_rev >= DPCD_REV_11 and DWN_STRM_PORTX_TYPE is
DOWN_STREAM_DETAILED_HDMI or DOWN_STREAM_DETAILED_DP_PLUS_PLUS.
Otherwise, it is not cleared, and stale information remains.
During mode validation:
function: dp_active_dongle_validate_timing reads
link->dpcd_caps.dongle_caps->dongle_type to determine the maximum
pixel clock to support. This information is now stale and no longer
valid.
[HOW]
dp_active_dongle_validate_timing should be using
link->dpcd_caps->dongle_type instead.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Static ramp to max refresh rate does not have capability check on
calculated v_total. Programming a lower v_total_min and max than the
total causes continuous spurious HPDs.
[How]
Add a capability check after v_total calculation similar to calculate
v_total helper functions.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
1. defer delay and sw start delay has been mixed up, defer delay was
programmed to AUX_SW_CONTROL:AUX_SW_START_DELAY.
2. There's no delay for defer
[how]
1. Set aux sw start to 0
2. Add delay for defer scenario
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
use vbios message to call smu for dpm level
also only program dmdata in vsyncflip as HW requirement.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Compiling with GCC 9.1.0 gives the following warning (I have
warnings-as-errors enabled):
drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc.c: In function 'dc_validate_seamless_boot_timing':
drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc.c:1180:8: error: 'se' may be used uninitialized in this function [-Werror=maybe-uninitialized]
1180 | if (!se->funcs->dp_get_pixel_format(
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1181 | se,
| ~~~
1182 | &hw_crtc_timing.pixel_encoding,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1183 | &hw_crtc_timing.display_color_depth))
[How]
Initialize se to NULL.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
we found using an active DP to HDMI panel that we weren't validating
dp_pixel_format and hardware timing v_front_porch, causing screen to
blank and/or corrupt while attempting a seamless boot.
[how]
added checks during dc_validate_seamless_boot_timing for these values
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Dongle 0x00E04C power down all internal circuits including
AUX communication preventing reading DPCD table.
Encoder will skip DP RX power down on disable output
to keep receiver powered all the time.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Number of audio endpoints wasn't updated from dcn20's 6 when created
[HOW]
Changed num_audio to 4 to match the correct sbios value
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
dp_48m_refclk_driver_pwdn is persistent through S3 and S5.
This was worked arround in SMU FW 55.21.0. Earlier FW don't have this fix
so we will hang on reboot
[how]
add a guard for smu versions before SMU FW 55.21.0
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The SMU message to enable this feature looks at argument. Previous code
didn't send right argument. This change will allow the feature to be
be enabled.
[How]
Fixed one issue where SMU message to enable the feature was sent without
setting the parameter.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If 48mhz refclk is turned off during PSR, we will have issue doing
link training during detection.
[How]
Get out of PSR before detection
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When diags adds a DWB via a stream update, we calculate MMHUBBUB
paramaters, but dc->current_state has not yet been updated
when the DWB programming happens. This leads to overflow on
high bandwidth tests since the incorrect MMHUBBUB arbitration
parameters are programmed.
[How]
Pass the updated context down to the (enable|update)_writeback functions
so that they can use the correct watermarks when programming MMHUBBUB.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
dpp2_get_optimal_number_of_taps is incorrect, and dcn2 should be using
dpp1_get_optimal_number_of_taps instead
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
There is a bug when determining if link training should be retried when
HPD is low in dp_verify_link_cap_with_retries.
[How]
Correctly, fail dp_verify_link_cap_with_retries without retry when
HPD is low.
Signed-off-by: Sivapiriyan Kumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When the driver sends a pipe set command to the DMCU FW, it does not wait
for the command to complete. This can lead to unpredictable behavior if,
for example, the driver were to request a pipe disable to the FW via MCP,
then power down some hardware before the firmware has completed processing
the command.
[How]
Wait for the DMCU FW to finish processing set pipe commands
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Output bitrate was mistakenly left out, causing corruption on some
DSC low resolution (such as 800x600) modes.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Some displays rely on the SPD verticle frequency maximum value.
Must round the calculated refresh rate to the nearest integer.
[How]
Round the nominal calculated refresh rate to the nearest whole
integer.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
This function was mistakenly reverted as part of a legitimate revert. The
old version that was reverted to has bad logic, and is causing situations
where p-state change support is being toggled when it shouldn't be,
resulting in hangs.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Type-c PHY config is not align with dpcd lane count.
When those values didn't match, it cause driver do
link training with 4 lane but phy only can output 2 lane.
The link trainig always fail.
[How]
1. Modify get_max_link_cap function. According DPALT_DP4
to update max lane count.
2. Add dp_mst_verify_link_cap to handle MST case because
we didn't call dp_mst_verify_link_cap for MST case.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Didn't send VSIF infopacket when it's 4k mode defined in HDMI 1.4b.
For HDMI 1.4b, While displaying 4k modes, it should send VSP.
[How]
Call mod_build_hf_vsif_infopacket() function to build info frame
and send it.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The register CM_TEST_DEBUG_DATA is used in dpp1_program_input_csc, which is
called from dpp2_cnv_setup, but the shifts and masks for the fields of that
register are not initialized for dcn2. This causes all reads of that register
to return 0.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
memcmp is vulnerable to regression due to dc_clocks structures not being
organized properly (not "current" clock related structures being at the beginning
of the structure) and causes unnecessary setting of the optimize bit
[how]
add a dcn sepcific comparator, implement for dcn2
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The vendor specific infoframe is needed for HDMI while displaying
specific modes.
DC supports sending it, but we aren't currently building it
[How]
Add mod_build_hf_vsif_infopacket() to build the vendor specific
info packet.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
HPD is not suppressed when we lower
clocks on renoir. B/c of this we do link
training when the 48mhz refclk is off, which
will cause ASIC hang.
[how]
Exit optimized power state for detection purpose.
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Currently pipe split may steal an existing ODM pipe depending on stream
sequence. This change prevents that from happening as easily.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Gary Kattan <Gary.Kattan@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When planes are added or removed from a stream, the change
in pipe usage from dynamic MPC combine can cause a second
stream using ODM combine to pick a different pipe to combine with.
In this scenario, a different OPP is connected to the ODM without
programming its FMT.
[How]
Reprogram the FMT in dcn20_program_pipe whenever a pipe is
newly enabled, or when its opp changes.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If VSTARTUP changes due to bandwidth requirements, we must
recalculate and update VLINE2 as well for proper flip reporting.
[How]
After all calls to program_global_sync which reconfigures
VSTARTUP, also make sure to update V_UPDATE (i.e. VLINE2 on DCNx).
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
A recent bug showed that logging would be useful in debugging
various gamma issues.
[How]
Fix formatting for easier graphing.
Prevent performance hit when doing diag.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Virtual signal means there is no display attached.
In this case we will assign a virtual signal type to the stream.
We should only enable the front end of the stream but not the back end.
[how]
When stream is enabling with virtual signal type, skip backend programming.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
While displaying 4k modes defined in HDMI1.4b, should set VIC to 0
and use VSP HDMI_VIC to indicate the mode.
[How]
Use functions defined in drm to set up the VIC correspondingly.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
To compare the crc of the framebuffer data at input of
display pipeline with the crc of the otg, we need to
disable pixel formatter's dynamic expansion feature during
crc capture and keep it enable in the normal operation.
[HOW]
Expose a new interface in DM and dc for pixel formatter
(fmt dynamic bitdepth expansion control). Interface control
the FMT_DYNAMIC_EXP_EN bit, during crc capture keep
it disabled.
Signed-off-by: Robin Singh <robin.singh@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This allows gfx cache to be probed and invalidated (for none-dirty cache lines)
on a HDP write (from either another GPU or CPU). This should work only for the
memory mapped as RW memory type newly added for arcturus, to achieve some cache
coherence b/t multiple memory clients.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Many logic in this function are HDP set up,
not gart set up. Moved those logic to gmc_v9_0_hw_init.
No functional change.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Christian konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use asic constants.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.5:
UAPI Changes:
-Colorspace: Expose different prop values for DP vs. HDMI (Gwan-gyeong Mun)
-fourcc: Add DRM_FORMAT_MOD_ARM_16X16_BLOCK_U_INTERLEAVED (Raymond)
-not_actually: s/ENOTSUPP/EOPNOTSUPP/ in drm_edid and drm_mipi_dbi. This should
not reach userspace, but adding here to specifically call that out (Daniel)
-i810: Prevent underflow in dispatch ioctls (Dan)
-komeda: Add ACLK sysfs attribute (Mihail)
-v3d: Allow userspace to clean up after render jobs (Iago)
Cross-subsystem Changes:
-MAINTAINERS:
-Add Alyssa & Steven as panfrost reviewers (Rob)
-Add Jernej as DE2 reviewer (Maxime)
-Add Chen-Yu as Allwinner maintainer (Maxime)
-staging: Make some stack arrays static const (Colin)
Core Changes:
-ttm: Allow drivers to specify their vma manager (to use gem mgr) (Gerd)
-docs: Various fixes in connector/encoder/bridge docs (Daniel, Lyude, Laurent)
-connector: Allow more than 3 possible encoders for a connector (José)
-dp_cec: Allow a connector to be associated with a cec device (Dariusz)
-various: Fix some compile/sparse warnings (Ville)
-mm: Ensure mm node removals are properly serialised (Chris)
-panel: Specify the type of panel for drm_panels for later use (Laurent)
-panel: Use drm_panel_init to init device and funcs (Laurent)
-mst: Refactors and cleanups in anticipation of suspend/resume support (Lyude)
-vram:
-Add lazy unmapping for gem bo's (Thomas)
-Unify and rationalize vram mm and gem vram (Thomas)
-Expose vmap and vunmap for gem vram objects (Thomas)
-Allow objects to be pinned at the top of vram to avoid fragmentation (Thomas)
Driver Changes:
-various: Include drm_bridge.h instead of relying on drm_crtc.h (Boris)
-ast/mgag200: Refactor show_cursor(), move cursor to top of video mem (Thomas)
-komeda:
-Add error event printing (behind CONFIG) and reg dump support (Lowry)
-Add suspend/resume support (Lowry)
-Workaround D71 shadow registers not flushing on disable (Lowry)
-meson: Add suspend/resume support (Neil)
-omap: Miscellaneous refactors and improvements (Tomi/Jyri)
-panfrost/shmem: Silence lockdep by using mutex_trylock (Rob)
-panfrost: Miscellaneous small fixes (Rob/Steven)
-sti: Fix warnings (Benjamin/Linus)
-sun4i:
-Add vcc-dsi regulator to sun6i_mipi_dsi (Jagan)
-A few patches to figure out the DRQ/start delay calc on dsi (Jagan/Icenowy)
-virtio:
-Add module param to switch resource reuse workaround on/off (Gerd)
-Avoid calling vmexit while holding spinlock (Gerd)
-Use gem shmem helpers instead of ttm (Gerd)
-Accommodate command buffer allocations too big for cma (David)
Cc: Rob Herring <robh@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Raymond Smith <raymond.smith@arm.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mihail Atanassov <Mihail.Atanassov@arm.com>
Cc: Lowry Li <Lowry.Li@arm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Iago Toral Quiroga <itoral@igalia.com>
Cc: David Riley <davidriley@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 10 Oct 2019 01:00:47 AM AEST
# gpg: using RSA key 732C002572DCAF79
# gpg: Can't check signature: public key not found
# Conflicts:
# drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c
# drivers/gpu/drm/i915/i915_drv.c
# drivers/gpu/drm/i915/i915_gem.c
# drivers/gpu/drm/i915/i915_gem_gtt.c
# drivers/gpu/drm/i915/i915_vma.c
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009150825.GA227673@art_vandelay
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Polaris and vegam use count for the value rather than
level. This looks like a copy paste typo from when
the code was adapted from previous asics.
I'm not sure that the SMU actually uses this value, so
I don't know that it actually is a bug per se.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=108609
Reported-by: Robert Strube <rstrube@gmail.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
cleanup error handling code and make sure temporary info array
with the handles are freed by amdgpu_bo_list_put() on
idr_replace()'s failure.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Participate in device cgroup. All kfd devices are exposed via /dev/kfd.
So use /dev/dri/renderN node.
Before exposing the device to a task check if it has permission to
access it. If the task (based on its cgroup) can access /dev/dri/renderN
then expose the device via kfd node.
If the task cannot access /dev/dri/renderN then process device data
(pdd) is not created. This will ensure that task cannot use the device.
In sysfs topology, all device nodes are visible irrespective of the task
cgroup. The sysfs node directories are created at driver load time and
cannot be changed dynamically. However, access to information inside
nodes is controlled based on the task's cgroup permissions.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add proper ifdefs around CIK code in kfd setup.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The vram vendor can be found as a separate sysfs file at:
/sys/class/drm/card[X]/device/mem_info_vram_vendor
The vram vendor is displayed as a string value.
v2: Use correct bit masking, and cache vram_vendor in gmc
v3: Drop unused functions for vram width, type, and vendor
Signed-off-by: Ori Messinger <ori.messinger@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
