| Age | Commit message (Collapse) | Author |
|---|
|
drm_crtc.h has no need for linux/media-bus-format.h, so don't
include it. Avoids useless rebuilds of the entire universe when
touching linux/media-bus-format.h.
Quite a few placs do currently depend on linux/media-bus-format.h
without actually including it directly. All of those need to be
fixed up.
v2: Deal with ingenic as well
v3: Fix up mxsfb and remaining parts of imx
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-4-ville.syrjala@linux.intel.com
|
|
"hdmi-connector.yaml" bindings defines an optional property
"ddc-en-gpios" for a single gpio to enable DDC operation.
Usually this controls +5V power on the HDMI connector.
This +5V may also be needed for HPD.
This was not reflected in code but is needed to make the CI20
board work.
Now, the driver activates the ddc gpio after probe and
deactivates after remove so it is "almost on".
But only if this driver is loaded (and not e.g. blacklisted
as module).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/3607e924b7c0cf0be956c0d49894be1442dbda41.1649330171.git.hns@goldelico.com
|
|
Since this bridge is tied to the connector, it acts like a passthrough,
so concerning the output & input bus formats, either pass the bus formats from the
previous bridge or return fallback data like done in the bridge function:
drm_atomic_bridge_chain_select_bus_fmts() & select_bus_fmt_recursive.
This permits avoiding skipping the negociation if the remaining bridge chain has
all the bits in place.
Without this bus fmt negociation breaks on drm/meson HDMI pipeline when attaching
dw-hdmi with DRM_BRIDGE_ATTACH_NO_CONNECTOR, because the last bridge of the
display-connector doesn't implement buf fmt callbacks and MEDIA_BUS_FMT_FIXED
is used leading to select an unsupported default bus format from dw-hdmi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020123947.2585572-2-narmstrong@baylibre.com
|
|
The "label" pointer is used for debug output. The code assumes that it
is either NULL or valid, but it is never set to NULL. It is either
valid or uninitialized.
Fixes: 0c275c30176b ("drm/bridge: Add bridge driver for display connectors")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013080825.GE6010@kili
|
|
Add DP support to display-connector driver. The driver will support HPD
via a GPIO and DP PWR.
DP PWR will be enabled at probe, which is not optimal, but I'm not sure
what would be a good place to enable and disable DP PWR. Perhaps
attach/detach, but I don't know if enabling HW is something that attach
is supposed to do.
In any case, I don't think there's much difference in power consumption
between the version in this patch and enabling the regulator later: if
the driver probes, supposedly it will attach very soon afterwards, and
we need to enable the DP PWR as soon as possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130112919.241054-3-tomi.valkeinen@ti.com
|
|
Display connectors are modelled in DT as a device node, but have so far
been handled manually in several bridge drivers. This resulted in
duplicate code in several bridge drivers, with slightly different (and
thus confusing) logics.
In order to fix this, implement a bridge driver for display connectors.
The driver centralises logic for the DVI, HDMI, VGAn composite and
S-video connectors and exposes corresponding bridge operations.
This driver in itself doesn't solve the issue completely, changes in
bridge and display controller drivers are needed to make use of the new
connector driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-16-laurent.pinchart@ideasonboard.com
|
