| Age | Commit message (Collapse) | Author |
|---|
|
When protected sufaces has flipped and pxp session is disabled,
display black pixels by using plane color CTM correction.
v2:
- Display black pixels in async flip too.
v3:
- Removed the black pixels logic for async flip. [Ville]
- Used plane state to force black pixels. [Ville]
v4 (Daniele): update pxp_is_borked check.
v5: rebase on top of v9 plane decryption moving the decrypt check
(Juston)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gaurav Kumar <kumar.gaurav@intel.com>
Cc: Shankar Uma <uma.shankar@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210924191452.1539378-15-alan.previn.teres.alexis@intel.com
|
|
Add support to enable/disable PLANE_SURF Decryption Request bit.
It requires only to enable plane decryption support when following
condition met.
1. PXP session is enabled.
2. Buffer object is protected.
v2:
- Used gen fb obj user_flags instead gem_object_metadata. [Krishna]
v3:
- intel_pxp_gem_object_status() API changes.
v4: use intel_pxp_is_active (Daniele)
v5: rebase and use the new protected object status checker (Daniele)
v6: used plane state for plane_decryption to handle async flip
as suggested by Ville.
v7: check pxp session while plane decrypt state computation. [Ville]
removed pointless code. [Ville]
v8 (Daniele): update PXP check
v9: move decrypt check after icl_check_nv12_planes() when overlays
have fb set (Juston)
v10 (Daniele): update PXP check again to match rework in earlier
patches and don't consider protection valid if the object has not
been used in an execbuf beforehand.
Cc: Bommu Krishnaiah <krishnaiah.bommu@intel.com>
Cc: Huang Sean Z <sean.z.huang@intel.com>
Cc: Gaurav Kumar <kumar.gaurav@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> #v9
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210924191452.1539378-14-alan.previn.teres.alexis@intel.com
|
|
While sanitizing the hardware state we're currently forcing
the pipe bottom color legacy csc/gamma bits on. That is not a
good idea as BIOSen are likely to leave gabage in the LUTs and
so doing this causes ugly visual glitches if and when the
planes covering the background get disabled. This was exactly
the case on this Dell Precision 5560 tgl laptop.
On icl+ we don't normally even use these legacy bits
anymore and instead use their GAMMA_MODE counterparts.
On earlier platforms the bits are used, but we still
shouldn't force them on without knowing what's in the LUT.
So two options, get rid of the whole thing, or do what
intel_color_commit() does to make sure the bottom color state
matches whatever out hardware readout produced. I chose the
latter since it'll match what happens on older platforms when
the primary plane gets turned off. In fact let's just call
intel_color_commit(). It'll also do some CSC programming but
since we don't have readout for that it'll actually just set
to all zeros. So in the unlikely case of CSC actually being
enabld by the BIOS we'll end up with all black until the first
atomic commit happens.
Still not totally sure what we should do about color management
features here in general. Probably the safest thing would be to
force everything off exactly at the same time when we disable
the primary plane as there is no guarantees that whatever the
LUTs/CSCs contain make any sense whatsoever without the
specific pixel data in the BIOS fb. And if we preserve the
primary plane then we should disable the color management
features exactly when the primary plane fb contents first
changes since the new content assumes more or less no
transformations. But of course synchronizing front buffer
rendering with anything else is a bit hard...
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3534
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210928185105.3030-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Check for the zero length front porch already in intel_mode_valid()
so that we get the same validation for both get_modes() and setcrtc()/etc.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930104133.30854-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
"CRTC fixup failed" is probably leftovers from pre-atomic days
when there was an actual fixup() function. Let's unify the debug
messages between encoder vs. crtc compute_config() calls.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930104133.30854-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Unify how we check for -EDEADLK vs. other errors from
crtc vs. encoder compute_config() calls.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930104133.30854-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Using standard -EAGAIN should be perfectly fine instead of using a
special case value.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930093229.28598-1-jani.nikula@intel.com
|
|
Keep the functionality and the assert code together.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0a5fa9b8d4d4615d4e6503b6bb33541c0bccffbb.1632992608.git.jani.nikula@intel.com
|
|
Keep the functionality and the assert code together.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0229659fb8af6c91c774408c6f7bb8c4ff8735e3.1632992608.git.jani.nikula@intel.com
|
|
Move assert_panel_unlocked() to intel_pps.c and rename
assert_pps_unlocked(). Keep the functionality and the assert code
together.
There's still a bit of a split between the eDP PPS usage in intel_pps.c
and all the other PPS usage, and assert_pps_unlocked() is arguably more
related to the latter. However, intel_pps.c is the best fit for anything
touching the PPS registers.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a9b77692a145891789eefb0447e082cfc22aaa85.1632992608.git.jani.nikula@intel.com
|
|
Keep the functionality and the assert code together.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/427d27eb4e5daca208d496d6c2ffc91ed90ba714.1632992608.git.jani.nikula@intel.com
|
|
This unnecessary flushes are hurting power-savings are it causes
features like PSR, FBC and DRRS to disable it self to handle
frontbuffer rendering, below some explanation of why each removed
call is not necessary.
The flush in intel_prepare_plane_fb() is not required as framebuffer
will be flipped and power-saving features do the proper flip handling
in hardware.
intel_find_initial_plane_obj() flush is not required because it is
only executed during driver load and at this point the power-saving
features are not even enabled.
And the last one intelfb_create(), is also not required as at this
point the fbdev was just allocated, userspace will draw on
it what will trigger frontbuffer invalidates and flushes later on.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930001409.254817-3-jose.souza@intel.com
|
|
Let's not configure the single transcoder's TRANSCONF multiple
times with bigjoiner. No real harm I suppose but since we already
have the bigjoiner if statement directly above might as well suck
this in there and skip the redundant programming.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-11-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
|
|
Adjust the HSW+ transcoder state readout to just read through
all the possible transcoders for the pipe, and stuff the results
in a bitmask.
We can conveniently cross check the bitmask for invalid
combinations of enabled transcoders, and later we can easily
extend the bitmask readout to handle the bigjoiner case.
One slight change in behaviour is that we no longer read out
the AONOFF->force_pfit.pfit bit for all the enabled "panel
transcoders". But having more than one enabled would anyway
be illegal so no big loss. Also the AONOFF selection should
only ever be used on HSW, which only has the EDP transcoder
an no DSI transcoders.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-10-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
|
|
Instead of directly accessing the TypeC port internal struct members,
add/use helpers to retrieve the corresponding properties.
No functional change.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-6-imre.deak@intel.com
|
|
Atm during driver loading and system resume TypeC ports are accessed
before their HW/SW state is synced. Move the TypeC port sanitization to
the encoder's sync_state hook to fix this.
v2: Handle the encoder disabled case in gen11_dsi_sync_state() as well
(Jose, Jani)
Fixes: f9e76a6e68d3 ("drm/i915: Add an encoder hook to sanitize its state during init/resume")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-1-imre.deak@intel.com
|
|
Display underrun in HDR mode when cursor is enabled.
RTL fix will be implemented CLKGATE_DIS_PSL_A bit 28-46520h.
As per W/A 1604331009, Disable cursor clock gating in HDR mode.
Bspec : 33451
Changes since V6:
- Address checkpatch warnings
- Bit ordering
Changes since V5:
- replace intel_de_read with intel_de_rmw - Jani
Changes since V4:
- Added WA needed check - Ville
- Replace BIT with REG_BIT - Ville
- Add WA enable/disable support back which was
added in V1 - Ville
Changes since V3:
- Disable WA when not in HDR mode or cursor plane
not active - Ville
- Extract required args from crtc_state - Ville
- Create HDR mode API using bdw_set_pipemisc ref - Ville
- Tested with HDR video as well full setmode, WA
applies and disables
Changes since V2:
- Made it general gen11 WA
- Removed WA needed check
- Added cursor plane active check
- Once WA enable, software will not disable
Changes since V1:
- Modified way CLKGATE_DIS_PSL bit 28 was modified
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929052442.2543054-1-tejaskumarx.surendrakumar.upadhyay@intel.com
|
|
Use a nop table for the cases where CxSR doesn't init properly.
v2: use a nop table (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bb0658d14afd02cca692cd58223800f68f4ff4ce.1632869550.git.jani.nikula@intel.com
|
|
Make nice clear tables instead of having things in two places.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d0f7e2c792dc40804555d26b6ede62f4bd2f23d6.1632869550.git.jani.nikula@intel.com
|
|
Most the dpll vtable into read-only memory.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0414a27317de3f335a8453a29486b746aa6862e7.1632869550.git.jani.nikula@intel.com
|
|
this single function might be possible to merge later, but
for now it's simple to just split it out.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba570aa10b694b2e8640e0c58430fd0053c306b7.1632869550.git.jani.nikula@intel.com
|
|
These are the watermark api between display and pm.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7130356324ef3de59b4e913f025d7dce822157ee.1632869550.git.jani.nikula@intel.com
|
|
This wraps the fdi link training vfunc to make it clearer.
Suggested by Jani.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1bb978bcb6f16fbdaf08f2800a179b774525b59e.1632869550.git.jani.nikula@intel.com
|
|
This adds wrappers around all the vtable callers so they are in
one place.
Suggested by Jani.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c3dd7aaad039e76acde9dda7211468907aa657c0.1632869550.git.jani.nikula@intel.com
|
|
This moves one wrapper from the pm->display side, and creates
wrappers for all the others, this should simplify things later.
One thing to note is that the code checks the existence of some
of these ptrs, so the wrappers are a bit complicated by that.
Suggested by Jani.
v2: fixup warnings in wrong place error.
v3 by Jani: fix intel_compute_global_watermarks() return value check
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ee2760c45896568c9dd9114a575509619bd44ef2.1632869550.git.jani.nikula@intel.com
|
|
The crtc was never being used here.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/70438bface47fa683cda8a9e95d0556fca448172.1632869550.git.jani.nikula@intel.com
|
|
PSR always had a requirement to only be enabled if there is active
planes but not following that never caused any issues.
But that changes in Alderlake-P, leaving PSR enabled without
active planes causes transcoder/port underruns.
Similar behavior was fixed during the pipe disable sequence by
commit 84030adb9e27 ("drm/i915/display: Disable audio, DRRS and PSR before planes").
intel_dp_compute_psr_vsc_sdp() had to move from
intel_psr_enable_locked() to intel_psr_compute_config() because we
need to be able to disable/enable PSR from atomic states without
connector and encoder state.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922215242.66683-3-jose.souza@intel.com
|
|
We were not completely following the selective fetch programming
sequence, here some things we were doing wrong:
- not programming plane selective fetch a PSR2_MAN_TRK_CTL registers
when doing a modeset
- programming PSR2_MAN_TRK_CTL out of vblank
With this changes the last remainig underrun found in Alderlake-P is
fixed.
Bspec: 55229
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922215242.66683-2-jose.souza@intel.com
|
|
Add support for remapping CCS FBs on ADL-P to remove the restriction
of the power-of-two sized stride and the 2MB surface offset alignment
for these FBs.
We can only remap the tiles on the main surface, not the tiles on the
CCS surface, so userspace has to generate the CCS surface aligning to
the POT size padded main surface stride (by programming the AUX
pagetable accordingly). For the required AUX pagetable setup, this
requires that either the main surface stride is 8 tiles or that the
stride is 16 tiles aligned (= 64 kbytes, the area mapped by one AUX
PTE).
v2:
- Init intel_remapped_info::plane_alignment only for remapped views and
do this from intel_fb_view_init().
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906182715.3915100-6-imre.deak@intel.com
|
|
intel_plane_atomic_calc_changes() deals with both the old and
new crtc/plane states. Make the variable names reflect that
more clearly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514125751.17075-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
|
|
Add helper function with returns if HDR mode in on
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210907113658.1351456-1-tejaskumarx.surendrakumar.upadhyay@intel.com
[vsyrjala: fix up alignment to match codingstyle]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
Extract the "panel transcoder" bitmask into a helper. We'll
have a couple of uses for this later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Pass the crtc+cpu_transcoder rather than the crtc state to
intel_dsc_power_domain(). This should allow us to reuse it
during readout as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.
I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
On Intel platforms we know that the ACPI connector device
node order will follow the order the driver (i915) decides.
The decision is made using the custom Intel ACPI OpRegion
(intel_opregion.c), though the driver does not actually know
that the values it sends to ACPI there are used for
associating a device node for the connectors, and assigning
address for them.
In reality that custom Intel ACPI OpRegion actually violates
ACPI specification (we supply dynamic information to objects
that are defined static, for example _ADR), however, it
makes assigning correct connector node for a connector entry
straightforward (it's one-on-one mapping).
Changes in v2 (Hans de goede):
- Take a reference on the fwnode which we assign to the connector,
for ACPI nodes this is a no-op but in the future we may see
software-fwnodes assigned to connectors which are ref-counted.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210817215201.795062-6-hdegoede@redhat.com
|
|
Frontbuffer rendering will be dropped for modern platforms but
before that we to prepare DRRS for it.
intel_drrs_flush and intel_drrs_invalidate will not be called
for platforms that will not support frontbuffer rendering so DRRS
needs another way to be notified about to page flips so it can change
between high and low refresh rates as needed.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210903221036.34770-3-jose.souza@intel.com
|
|
Pull drm updates from Dave Airlie:
"Highlights:
- i915 has seen a lot of refactoring and uAPI cleanups due to a
change in the upstream direction going forward
This has all been audited with known userspace, but there may be
some pitfalls that were missed.
- i915 now uses common TTM to enable discrete memory on DG1/2 GPUs
- i915 enables Jasper and Elkhart Lake by default and has preliminary
XeHP/DG2 support
- amdgpu adds support for Cyan Skillfish
- lots of implicit fencing rules documented and fixed up in drivers
- msm now uses the core scheduler
- the irq midlayer has been removed for non-legacy drivers
- the sysfb code now works on more than x86.
Otherwise the usual smattering of stuff everywhere, panels, bridges,
refactorings.
Detailed summary:
core:
- extract i915 eDP backlight into core
- DP aux bus support
- drm_device.irq_enabled removed
- port drivers to native irq interfaces
- export gem shadow plane handling for vgem
- print proper driver name in framebuffer registration
- driver fixes for implicit fencing rules
- ARM fixed rate compression modifier added
- updated fb damage handling
- rmfb ioctl logging/docs
- drop drm_gem_object_put_locked
- define DRM_FORMAT_MAX_PLANES
- add gem fb vmap/vunmap helpers
- add lockdep_assert(once) helpers
- mark drm irq midlayer as legacy
- use offset adjusted bo mapping conversion
vgaarb:
- cleanups
fbdev:
- extend efifb handling to all arches
- div by 0 fixes for multiple drivers
udmabuf:
- add hugepage mapping support
dma-buf:
- non-dynamic exporter fixups
- document implicit fencing rules
amdgpu:
- Initial Cyan Skillfish support
- switch virtual DCE over to vkms based atomic
- VCN/JPEG power down fixes
- NAVI PCIE link handling fixes
- AMD HDMI freesync fixes
- Yellow Carp + Beige Goby fixes
- Clockgating/S0ix/SMU/EEPROM fixes
- embed hw fence in job
- rework dma-resv handling
- ensure eviction to system ram
amdkfd:
- uapi: SVM address range query added
- sysfs leak fix
- GPUVM TLB optimizations
- vmfault/migration counters
i915:
- Enable JSL and EHL by default
- preliminary XeHP/DG2 support
- remove all CNL support (never shipped)
- move to TTM for discrete memory support
- allow mixed object mmap handling
- GEM uAPI spring cleaning
- add I915_MMAP_OBJECT_FIXED
- reinstate ADL-P mmap ioctls
- drop a bunch of unused by userspace features
- disable and remove GPU relocations
- revert some i915 misfeatures
- major refactoring of GuC for Gen11+
- execbuffer object locking separate step
- reject caching/set-domain on discrete
- Enable pipe DMC loading on XE-LPD and ADL-P
- add PSF GV point support
- Refactor and fix DDI buffer translations
- Clean up FBC CFB allocation code
- Finish INTEL_GEN() and friends macro conversions
nouveau:
- add eDP backlight support
- implicit fence fix
msm:
- a680/7c3 support
- drm/scheduler conversion
panfrost:
- rework GPU reset
virtio:
- fix fencing for planes
ast:
- add detect support
bochs:
- move to tiny GPU driver
vc4:
- use hotplug irqs
- HDMI codec support
vmwgfx:
- use internal vmware device headers
ingenic:
- demidlayering irq
rcar-du:
- shutdown fixes
- convert to bridge connector helpers
zynqmp-dsub:
- misc fixes
mgag200:
- convert PLL handling to atomic
mediatek:
- MT8133 AAL support
- gem mmap object support
- MT8167 support
etnaviv:
- NXP Layerscape LS1028A SoC support
- GEM mmap cleanups
tegra:
- new user API
exynos:
- missing unlock fix
- build warning fix
- use refcount_t"
* tag 'drm-next-2021-08-31-1' of git://anongit.freedesktop.org/drm/drm: (1318 commits)
drm/amd/display: Move AllowDRAMSelfRefreshOrDRAMClockChangeInVblank to bounding box
drm/amd/display: Remove duplicate dml init
drm/amd/display: Update bounding box states (v2)
drm/amd/display: Update number of DCN3 clock states
drm/amdgpu: disable GFX CGCG in aldebaran
drm/amdgpu: Clear RAS interrupt status on aldebaran
drm/amdgpu: Add support for RAS XGMI err query
drm/amdkfd: Account for SH/SE count when setting up cu masks.
drm/amdgpu: rename amdgpu_bo_get_preferred_pin_domain
drm/amdgpu: drop redundant cancel_delayed_work_sync call
drm/amdgpu: add missing cleanups for more ASICs on UVD/VCE suspend
drm/amdgpu: add missing cleanups for Polaris12 UVD/VCE on suspend
drm/amdkfd: map SVM range with correct access permission
drm/amdkfd: check access permisson to restore retry fault
drm/amdgpu: Update RAS XGMI Error Query
drm/amdgpu: Add driver infrastructure for MCA RAS
drm/amd/display: Add Logging for HDMI color depth information
drm/amd/amdgpu: consolidate PSP TA init shared buf functions
drm/amd/amdgpu: add name field back to ras_common_if
drm/amdgpu: Fix build with missing pm_suspend_target_state module export
...
|
|
Enable MIPI DSI support on ADL-P platform.
The esc clock changes, WA changes are taken care
in the previous patches.
As per the Bspec the seq remains to be same as TGL.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826054811.10572-3-vandita.kulkarni@intel.com
|
|
Apparently the last reader of i915->active_pipes was removed with commit
ef79d62b5ce5 ("drm/i915: Encapsulate dbuf state handling harder"), and
now it's only ever written to. Remove it completely.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826141830.889-1-jani.nikula@intel.com
|
|
This fairly detailed stuff that really has no place in
intel_display.c. Combine the calls into one to avoid exposing both.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b0037775480380e5d73d0b112da478d6f0ea30fe.1629906431.git.jani.nikula@intel.com
|
|
Accept slight duplication in the fdi link train hooks in exchange for
simplification in ilk_pch_enable(). This lets us make
ivb_update_fdi_bc_bifurcation() static again, now in intel_fdi.c.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7984e670c6bb092d213d90f838d526d594d4a690.1629906431.git.jani.nikula@intel.com
|
|
Move FDI related functions to intel_fdi.c. Don't bother with renaming as
we'll make the functions static shortly.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fd8afe4876f0b0762a9c69e01762a8dba31349e5.1629906431.git.jani.nikula@intel.com
|
|
Move FDI related functions to intel_fdi.c. Rename to have intel_fdi
prefix while at it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/da1609dfce4623f8ec86254aea6c2c8679b6a37f.1629906431.git.jani.nikula@intel.com
|
|
intel_prepare_shared_dpll() is now useless, so get rid of it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-14-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Can't think of a good reason why we'd need to program the FP
dividers so early. Let's just do it when programming the rest
of the DPLL.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
We always call the vlv/chv prepare_pll() just before enable_pll().
Move the calls into the enable_pll() funcs. We can also
consolidate the DPLL_VCO_ENABLE checks while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Stop passing both the crtc and its state to the DPLL functions.
The state alone is enough.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
The current gen2 DPLL readout code:
* assumes i845/i865 have LVDS which is not true
* assumes only pipe B can drive LVDS (true, but makes
the code appear a bit magical)
* hard to parse in general
Clean it up by checking for i85x (the only gen2 platform
with LVDS) and reusing intel_lvds_port_enabled().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Split out fb related stuff from intel_display.c to intel_fb.c.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/76b61738857619c1cce6e4306d14da19ee3bbf08.1629721467.git.jani.nikula@intel.com
|
|
Split out fb related stuff from intel_display.c to intel_fb.c.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0b894be3a6acff5fe917b686771a084a6c2aa535.1629721467.git.jani.nikula@intel.com
|
