summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/i915/display/intel_dp.h
AgeCommit message (Collapse)Author
2023-08-18drm/i915/dp: Consider output_format while computing dsc bppAnkit Nautiyal
While using DSC the compressed bpp is computed assuming RGB output format. Consider the output_format and compute the compressed bpp during mode valid and compute config steps. For DP-MST we currently use RGB output format only, so continue using RGB while computing compressed bpp for MST case. v2: Use output_bpp instead for pipe_bpp to clamp compressed_bpp. (Ville) Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230817142459.89764-2-ankit.k.nautiyal@intel.com
2023-06-02drm/i915/dp: stop caching has_hdmi_sink in struct intel_dpJani Nikula
Use the information stored in display info. Add intel_dp_has_hdmi_sink() helper to access it. v2: Rebased Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/748103fda572b3552e5bbdafb300d8508d4eeaf4.1685437500.git.jani.nikula@intel.com
2023-05-16drm/i915/tc: Reset TypeC PHYs left enabled in DP-alt mode after the sink ↵Imre Deak
disconnects If the output on a DP-alt link with its sink disconnected is kept enabled for too long (about 20 sec), then some IOM/TCSS firmware timeout will cause havoc on the PCI bus, at least for other GFX devices on it which will stop powering up. Since user space is not guaranteed to do a disabling modeset in time, switch such disconnected but active links to TBT mode - which is without such shortcomings - with a 2 second delay. If the above condition is detected already during the driver load/system resume sanitization step disable the output instead, as at that point no user space or kernel client depends on a consistent output state yet and because subsequent atomic modeset on such connectors - without the actual sink capabilities available - can fail. An active/disconnected port as above will also block the HPD status of other active/disconnected ports to get updated (stuck in the connected state), until the former port is disabled, its PHY is disconnected and a ~10 ms delay has elapsed. This means the link state for all TypeC ports/CRTCs must be rechecked after a CRTC is disabled due to the above reason. For this disconnect the PHY synchronously after the CRTC/port is disabled and recheck all CRTCs for the above condition whenever such a port is disabled. To account for a race condition during driver loading where the sink is disconnected after the above sanitization step and before the HPD interrupts get enabled, do an explicit check/link reset if needed from the encoder's late_register hook, which is called after the HPD interrupts are enabled already. v2: - Handle an active/disconnected port blocking the HPD state update of another active/disconnected port. - Cancel the delayed work resetting the link also from the encoder enable/suspend/shutdown hooks. - Rebase on the earlier intel_modeset_lock_ctx_retry() addition, fixing here the missed atomic state reset in case of a retry. - Fix handling of an error return from intel_atomic_get_crtc_state(). - Recheck if the port needs to be reset after all the atomic state is locked and async commits are waited on. v3: - Add intel_crtc_needs_link_reset(), instead of open-coding it, keep intel_crtc_has_encoders(). (Ville) - Fix state dumping and use a bitmask to track disabled CRTCs in intel_sanitize_all_crtcs(). (Ville) - Set internal in intel_atomic_state right after allocating it. (Ville) - Recheck all CRTCs (not yet force-disabled) after a CRTC is force-disabled for any reason (not only due to a link state) in intel_sanitize_all_crtcs(). - Reduce delay after CRTC disabling to 20ms, and use the simpler msleep(). - Clarify code comment about HPD behaviour in intel_sanitize_all_crtcs(). - Move all the TC link reset logic to intel_tc.c . - Cancel the link reset work synchronously during system suspend, driver unload and shutdown. v4: - Rebased on previous patch, which allows calling the TC port suspend/cleanup handlers without modeset locks held; remove the display driver suspended assert from the link reset work accordingly. v5: (Ville) - Remove reset work canceling from intel_ddi_pre_pll_enable(). - Track a crtc vs. pipe mask in intel_sanitize_all_crtcs(). - Add reset_link_commit() to clarify the intel_modeset_lock_ctx_retry loop. Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5860 Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-2-imre.deak@intel.com
2022-12-13drm/i915: Bpp/timeslot calculation fixes for DP MST DSCStanislav Lisovskiy
Fix intel_dp_dsc_compute_config, previously timeslots parameter was used in fact not as a timeslots, but more like a ratio timeslots/64, which of course didn't have any effect for SST DSC, but causes now issues for MST DSC. Secondly we need to calculate pipe_bpp using intel_dp_dsc_compute_bpp only for SST DSC case, while for MST case it has been calculated earlier already with intel_dp_dsc_mst_compute_link_config. Third we also were wrongly determining sink min bpp/max bpp, those limites should be intersected with our limits to find common acceptable bpp's, plus on top of that we should align those with VESA bpps and only then calculate required timeslots amount. Some MST hubs started to work only after third change was made. v2: Make kernel test robot happy(claimed there was unitialzed use, while there is none) v3: Rename intel_dp_dsc_nearest_vesa_bpp to intel_dp_dsc_nearest_valid_bpp (Manasi Navare) Reviewed-by: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221123100718.29130-1-stanislav.lisovskiy@intel.com
2022-12-13drm/i915: Extract VESA DSC bpp alignment to separate functionStanislav Lisovskiy
We might to use that function separately from intel_dp_dsc_compute_config for DP DSC over MST case, because allocating bandwidth in that case can be a bit more tricky. So in order to avoid code copy-pasta lets extract this to separate function and reuse it for both SST and MST cases. v2: Removed multiple blank lines v3: Rename intel_dp_dsc_nearest_vesa_bpp to intel_dp_dsc_nearest_valid_bpp to reflect its meaning more properly. (Manasi Navare) Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Reviewed-by: Manasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221123100551.29080-1-stanislav.lisovskiy@intel.com
2022-12-13drm/i915: Add DSC support to MST pathStanislav Lisovskiy
Whenever we are not able to get enough timeslots for required PBN, let's try to allocate those using DSC, just same way as we do for SST. v2: Removed intel_dp_mst_dsc_compute_config and refactored intel_dp_dsc_compute_config to support timeslots as a parameter(Ville Syrjälä) v3: - Rebased - Added a debug to see that we at least try reserving VCPI slots using DSC, because currently its not visible from the logs, thus making debugging more tricky. - Moved timeslots to numerator, where it should be. v4: - Call drm_dp_mst_atomic_check already during link config computation, because we need to know already by this moment if uncompressed amount of VCPI slots needed can fit, otherwise we need to use DSC. (thanks to Vinod Govindapillai for pointing this out) v5: - Put pipe_config->bigjoiner_pipes back to original condition in intel_dp_dsc_compute_config (don't remember when I lost it) v6: - Removed unnecessary drm_dp_mst_atomic_check as it is now always called in a newly introduced intel_dp_mst_find_vcpi_slots_for_bpp function (Vinod Govindapillai) Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com> Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221101094222.22091-5-stanislav.lisovskiy@intel.com
2022-09-06Revert "drm/i915: Add DSC support to MST path"Jani Nikula
This reverts commit e1a84ba850128b3984973786829e610ae4ee0e2e. Part of a series where patches were modified while applying to resolve conflicts, leading to further conflicts between drm-misc-next and drm-intel-next, resulting in build failures in drm-tip. To be applied again on a baseline with drm-misc-next and drm-intel-next in sync. Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2022-09-06drm/i915: Add DSC support to MST pathStanislav Lisovskiy
Whenever we are not able to get enough timeslots for required PBN, let's try to allocate those using DSC, just same way as we do for SST. v2: Removed intel_dp_mst_dsc_compute_config and refactored intel_dp_dsc_compute_config to support timeslots as a parameter(Ville Syrjälä) v3: - Rebased - Added a debug to see that we at least try reserving VCPI slots using DSC, because currently its not visible from the logs, thus making debugging more tricky. - Moved timeslots to numerator, where it should be. v4: - Call drm_dp_mst_atomic_check already during link config computation, because we need to know already by this moment if uncompressed amount of VCPI slots needed can fit, otherwise we need to use DSC. (thanks to Vinod Govindapillai for pointing this out) v5: - Put pipe_config->bigjoiner_pipes back to original condition in intel_dp_dsc_compute_config (don't remember when I lost it) v6: - Removed unnecessary drm_dp_mst_atomic_check as it is now always called in a newly introduced intel_dp_mst_find_vcpi_slots_for_bpp function (Vinod Govindapillai) Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com> Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220905085744.29637-5-stanislav.lisovskiy@intel.com
2022-05-27drm/i915/bios: Split VBT data into per-panel vs. global partsVille Syrjälä
Move the panel specific VBT parsing to happen during the output probing stage. Needs to be done because the VBT parsing will need to look at the EDID to determine the correct panel_type on some machines. We split the parsed VBT data (i915->vbt) along the same boundary. For the moment we just hoist all the panel specific stuff into connector->panel.vbt since that seems like the most convenient place for eg. the backlight code. Note that we simply drop the drrs type check from intel_drrs_frontbuffer_update() since that operates on the whole device rather than a specific connector/encoder. But the check was just a micro optimization so removing it doesn't actually mattter for correctness. TODO: Lot's of cleanup to be done in the future. Eg. most of the DSI stuff could probably be eliminated entirely and just parsed on demand during DSI init. v2: Note the intel_drrs_frontbuffer_update() change Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-13-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-05-27drm/i915: Extract intel_edp_fixup_vbt_bpp()Ville Syrjälä
We have the same "override eDP VBT bpp with the current bpp" code duplciated in two places. Extract it to a helper function. TODO: Having this in .get_config() is pretty ugly. Should probably try to move it somewhere else (setup_hw_state()/etc.)... Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-3-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2022-02-02drm/i915: Only include i915_reg.h from .c filesMatt Roper
Several of our i915 header files, have been including i915_reg.h. This means that any change to i915_reg.h will trigger a full rebuild of pretty much every file of the driver, even those that don't have any kind of register access. Let's delete the i915_reg.h include from all headers and add an explicit include from the .c files that truly need the register definitions; those that need a definition of i915_reg_t for a function definition can get it from i915_reg_defs.h instead. We also remove two non-register #define's (VLV_DISPLAY_BASE and GEN12_SFC_DONE_MAX) into i915_reg_defs.h to allow us to drop the i915_reg.h include from a couple of headers. There's probably a lot more header dependency optimization possible, but the changes here roughly cut the number of files compiled after 'touch i915_reg.h' in half --- a good first step. Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220127234334.4016964-7-matthew.d.roper@intel.com
2021-12-01drm/i915/dp: Perform 30ms delay after source OUI writeLyude Paul
While working on supporting the Intel HDR backlight interface, I noticed that there's a couple of laptops that will very rarely manage to boot up without detecting Intel HDR backlight support - even though it's supported on the system. One example of such a laptop is the Lenovo P17 1st generation. Following some investigation Ville Syrjälä did through the docs they have available to them, they discovered that there's actually supposed to be a 30ms wait after writing the source OUI before we begin setting up the rest of the backlight interface. This seems to be correct, as adding this 30ms delay seems to have completely fixed the probing issues I was previously seeing. So - let's start performing a 30ms wait after writing the OUI, which we do in a manner similar to how we keep track of PPS delays (e.g. record the timestamp of the OUI write, and then wait for however many ms are left since that timestamp right before we interact with the backlight) in order to avoid waiting any longer then we need to. As well, this also avoids us performing this delay on systems where we don't end up using the HDR backlight interface. V3: * Move last_oui_write into intel_dp V2: * Move panel delays into intel_pps Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Fixes: 4a8d79901d5b ("drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)") Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: <stable@vger.kernel.org> # v5.12+ Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20211130212912.212044-1-lyude@redhat.com
2021-09-30drm/i915: Enable TPS3/4 on all platforms that support themVille Syrjälä
Stop using HBR2/3 support as a proxy for TPS3/4 support. The two are no longer 1:1 in the hardware, arguably they never were due to HSW ULX which does support TPS3 while being limited to HBR1. In more recent times GLK gained support for TPS4 while being limited to HBR2. And on CNL+ some ports support HBR3 while others are limited to HBR2, but all ports support TPS4. v2: s/INTEL_GEN/DISPLAY_VER/ Reviewed-by: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210929162404.6717-1-ville.syrjala@linux.intel.com Acked-by: Jani Nikula <jani.nikula@intel.com>
2021-09-23drm/i915/display: Only keep PSR enabled if there is active planesJosé Roberto de Souza
PSR always had a requirement to only be enabled if there is active planes but not following that never caused any issues. But that changes in Alderlake-P, leaving PSR enabled without active planes causes transcoder/port underruns. Similar behavior was fixed during the pipe disable sequence by commit 84030adb9e27 ("drm/i915/display: Disable audio, DRRS and PSR before planes"). intel_dp_compute_psr_vsc_sdp() had to move from intel_psr_enable_locked() to intel_psr_compute_config() because we need to be able to disable/enable PSR from atomic states without connector and encoder state. Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210922215242.66683-3-jose.souza@intel.com
2021-09-20drm/i915/dp: add helper for checking for UHBR link rateJani Nikula
Helpful abstraction to avoid duplication. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/fe9a222ad900da797c989de9f7fa13928d2c9861.1631191763.git.jani.nikula@intel.com
2021-08-30drm/i915/display: Move DRRS code its own fileJosé Roberto de Souza
intel_dp.c is a 5k lines monster, so moving DRRS out of it to reduce some lines from it. Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-2-jose.souza@intel.com
2021-08-24drm/i915/dp: add max data rate calculation for UHBR ratesJani Nikula
DP 2.0 UHBR link rates always use 128b/132b channel encoding, which has a different data bandwidth efficiency from 8b/10b. The computation is slightly convoluted due to the units we use; this is all explained in the added comment. v2: Clarified comment (Manasi) Reviewed-by: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/8afd8d97a04c2d86c2dcadfed9f8e1f84272a13c.1629735412.git.jani.nikula@intel.com
2021-08-24drm/i915/dp: use actual link rate values in struct link_config_limitsJani Nikula
The MST code uses actual link rates in the limits struct, while the DP code in general uses indexes to the ->common_rates[] array. Fix the confusion by using actual link rate values everywhere. This is a better abstraction than some obscure index. Rename the struct members while at it to ensure all the places are covered. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/d70ab7261abacd367d3a6a47102575eb88a55cd4.1629735412.git.jani.nikula@intel.com
2021-04-28drm/i915/hdcp: add intel_dp_hdcp.h and rename init accordinglyJani Nikula
Add separate intel_dp_hdcp.h to go with intel_dp_hdcp.c, and rename the init function intel_dp_hdcp_init() to follow naming where function prefix matches the file name. Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210427114520.4740-1-jani.nikula@intel.com
2021-03-19drm/i915: Introduce g4x_dp.cVille Syrjälä
Move the g4x+ DP code into a new file. This will leave mostly platform agnostic code in intel_dp.c. Well, the misplaced phy test stuff pretty much ruins that, but let's squint real hard for now. v2: Add comment exlaining which platforms are covered (Daniel) Leave intel_dp_unused_lane_mask() be since it is pretty generic Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210318161015.22070-6-ville.syrjala@linux.intel.com
2021-03-19drm/i915: Split intel_ddi_encoder_reset() from intel_dp_encoder_reset()Ville Syrjälä
Most of intel_dp_encoder_reset() is for pre-ddi platforms. Make a clean split. Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210318161015.22070-5-ville.syrjala@linux.intel.com
2021-03-19drm/i915: Relocate intel_dp_program_link_training_pattern()Ville Syrjälä
intel_dp_program_link_training_pattern() clearly belongs in intel_dp_link_training.c. Make it so. Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210318161015.22070-4-ville.syrjala@linux.intel.com
2021-01-21drm/i915/dp: split out aux functionality to intel_dp_aux.cJani Nikula
Split out the DP aux functionality to a new intel_dp_aux.[ch]. This is a surprisingly clean cut. v2: - Remove intel_dp_pack_aux declaration from intel_dp.h (Anshuman) - Fixed some whitespace/comment checkpatch warnings Cc: Anshuman Gupta <anshuman.gupta@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210120101834.19813-4-jani.nikula@intel.com
2021-01-19drm/i915: Fix the PHY compliance test vs. hotplug mishapVille Syrjälä
I accidentally added the compliance test hacks only to intel_dp_hotplug() which doesn't even get used on any DDI platform. Put the same crap into intel_ddi_hotplug(). Cc: Imre Deak <imre.deak@intel.com> Fixes: 193af12cd681 ("drm/i915: Shove the PHY test into the hotplug work") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210114205046.8247-7-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
2021-01-14drm/i915/pps: abstract panel power sequencer from intel_dp.cJani Nikula
In a long overdue refactoring, split out all panel sequencer code from intel_dp.c to new intel_pps.[ch]. The first part is mostly just code movement as-is, without cleanups or functional changes. We need to add a vlv_get_dpll() helper to get at the vlv/chv dpll from pps code. v2: Rebase. Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/14cc59d5734432ad976cd49ff8efce8fa413e5b2.1610127741.git.jani.nikula@intel.com
2021-01-13drm/i915/dp: Move intel_dp_set_signal_levels() to intel_dp_link_training.cImre Deak
intel_dp_set_signal_levels() is needed for link training, so move it to intel_dp_link_training.c. Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201229172201.4155327-1-imre.deak@intel.com
2020-12-22drm/i915/display: Let PCON convert from RGB to YCbCr if it canAnkit Nautiyal
If PCON has capability to convert RGB->YCbCr colorspace and also to 444->420 downsampling then for any YUV420 only mode, we can let the PCON do all the conversion. If the PCON supports RGB->YCbCr conversion for all BT2020, BT709, BT601, choose the one that is selected by userspace via connector colorspace property, otherwise default to BT601. v2: As suggested by Uma Shankar, considered case for colorspace BT709 and BT2020, and default to BT601. Also appended dir 'display' in commit message. v3: Fixed typo in condition for printing one of the error msg. v4: As suggested by Uma Shankar: -Fixed bug in determining the colorspace for RGB->YCbCr conversion. -Fixed minor formatting issues Also updated the commit message as per latest changes. Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> [Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.] Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-16-ankit.k.nautiyal@intel.com
2020-12-22drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encodingAnkit Nautiyal
When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink via DP HDMI2.1 PCON, the PCON can be configured to decode the DSC1.1 compressed stream and encode to DSC1.2. It then sends the DSC1.2 compressed stream to the HDMI2.1 sink. This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder capabilities. v2: Addressed review comments from Uma Shankar: -fixed the error in packing pps parameter values -added check for pcon in the pcon related function -appended display in commit message v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w supported by sink. Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> [Jani: Fixed checkpatch BRACES, LINE_SPACING, PARENTHESIS_ALIGNMENT.] Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-15-ankit.k.nautiyal@intel.com
2020-12-22drm/i915: Add support for starting FRL training for HDMI2.1 via PCONAnkit Nautiyal
This patch adds functions to start FRL training for an HDMI2.1 sink, connected via a PCON as a DP branch device. This patch also adds a new structure for storing frl training related data, when FRL training is completed. v2: As suggested by Uma Shankar: -renamed couple of variables for better clarity -tweaked the macros used for correct semantics for true/false -fixed other styling issues. v3: Completed the TODO for condition for going to FRL mode. Modified the condition to determine the required FRL b/w based only on the Pcon and Sink's max FRL values. Moved the frl structure initialization to intel_dp_init_connector(). v4: Fixed typo in initialization of frl structure. v5: Always use FRL if its possible, instead of enabling only for higher modes as done in v3. Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2) [Jani: Fixed checkpatch BRACES, CONSTANT_COMPARISON.] Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-10-ankit.k.nautiyal@intel.com
2020-11-18drm/i915/dp: Allow big joiner modes in intel_dp_mode_valid(), v3.Maarten Lankhorst
Small changes to intel_dp_mode_valid(), allow listing modes that can only be supported in the bigjoiner configuration, which is not supported yet. v13: * Allow bigjoiner if hdisplay >5120 v12: * slice_count logic simplify (Ville) * Fix unnecessary changes in downstream_mode_valid (Ville) v11: * Make intel_dp_can_bigjoiner non static so it can be used in intel_display (Manasi) v10: * Simplify logic (Ville) * Allow bigjoiner on edp (Ville) v9: * Restric Bigjoiner on PORT A (Ville) v8: * use source dotclock for max dotclock (Manasi) v7: * Add can_bigjoiner() helper (Ville) * Pass bigjoiner to plane_size validation (Ville) v6: * Rebase after dp_downstream mode valid changes (Manasi) v5: * Increase max plane width to support 8K with bigjoiner (Maarten) v4: * Rebase (Manasi) Changes since v1: - Disallow bigjoiner on eDP. Changes since v2: - Rename intel_dp_downstream_max_dotclock to intel_dp_max_dotclock, and split off the downstream and source checking to its own function. (Ville) v3: * Rebase (Manasi) Signed-off-by: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> [vsyrjala: * Keep bigjoiner disabled until everything is ready * Appease checkpatch] Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Animesh Manna <animesh.manna@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-3-manasi.d.navare@intel.com
2020-10-20drm/i915: s/intel_dp_sink_dpms/intel_dp_set_power/Ville Syrjälä
Rename intel_dp_sink_dpms() to intel_dp_set_power() so one doesn't always have to convert from the DPMS enum values to the actual DP D-states. Also when dealing with a branch device this has nothing to do with any sink, so the old name was nonsense anyway. Also adjust the debug message accordingly, and pimp it with the standard encoder id+name thing. Trivial bits done with cocci: @@ expression DP; @@ ( - intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF) + intel_dp_set_power(DP, DP_SET_POWER_D3) | - intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON) + intel_dp_set_power(DP, DP_SET_POWER_D0) ) Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
2020-10-12drm/i915: Switch to LTTPR non-transparent mode link trainingImre Deak
The DP Standard's recommendation is to use the LTTPR non-transparent mode link training if LTTPRs are detected, so let's do this. Besides power-saving, the advantages of this are that the maximum number of LTTPRs can only be used in non-transparent mode (the limit is 5-8 in transparent mode), and it provides a way to narrow down the reason for a link training failure to a given link segment. Non-transparent mode is probably also the mode that was tested the most by the industry. The changes in this patchset: - Pass the DP PHY that is currently link trained to all LT helpers, so that these can access the correct LTTPR/DPRX DPCD registers. - During LT take into account the LTTPR common lane rate/count and the per LTTPR-PHY vswing/pre-emph limits. - Switch to LTTPR non-transparent LT mode and train each link segment according to the sequence in DP Standard v2.0 (complete CR/EQ for each segment before continuing with the next segment). v2: - Switch to non-transparent mode during connector detection, which is required before reading the per-PHY LTTPR capabilities. - Move the DP_PHY_LTTPR() macro to drm_dp_helper.h (Ville) - Use the new drm_dp_dpcd_read_phy_link_status() instead of adding the same logic to intel_dp_get_link_status(). (Ville) - Make intel_dp_lttpr_phy_caps() return a pointer to the whole array instead of a pointer to its first element. (Ville) - Add the intel_dp_phy_is_downstream_of_source() helper. (Ville) - Add a code comment about the disable->enable quirk of non-transparent mode. - Add the intel_dp_training_pattern_set_reg() helper. - Fix checkpatch/sparse warns. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-7-imre.deak@intel.com
2020-10-12drm/i915: Simplify the link training functionsImre Deak
Split the prepare, link training, fallback-handling steps into their own functions for clarity and as a preparation for the upcoming LTTPR changes. While at it also: - Unexport and inline intel_dp_set_idle_link_train(), which is used at a single place. - Add some documentation to functions that are exported or that can use a better description about which part of the LT sequence they implement. v2: (Ville) - Unexport/inline intel_dp_set_idle_link_train() - Make the documentation of intel_dp_prepare_link_train()/intel_dp_stop_link_train() more accurate wrt. HW specific details. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-3-imre.deak@intel.com
2020-10-09drm/i915: Wait for eDP panel power cycle delay on reboot on all platformsVille Syrjälä
Extend the eDP panel power cycle delay wait on reboot handling to cover all platforms. No reason to think that VLV/CHV are in any way special since the documentation states that the hardware power cycle delay goes back to its default value on reset, and that may not be enough for all panels. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-4-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
2020-10-06drm/i915: Add an encoder hook to sanitize its state during init/resumeImre Deak
Atm, if a full modeset is performed during the initial modeset the link training will happen with uninitialized max DP rate and lane count. Make sure the corresponding encoder state is initialized by adding an encoder hook called during driver init and system resume. A better alternative would be to store all states in the CRTC state and make this state available for the link re-training code. Also instead of the DPCD read in the hook there should be really a proper sink HW readout in place. Both of these require a bigger rework, so for now opting for this minimal fix to make at least full initial modesets work. The patch is based on https://patchwork.freedesktop.org/patch/101473/?series=10354&rev=3 v2: (Ville) - s/sanitize_state/sync_state/ - No point in calling the hook when CRTC is disabled, remove the call. - No point in calling the hook for MST, remove it. v3: Check only DPCD_REV to avoid clobbering intel_dp->dpcd. (Ville) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201005230154.1477653-1-imre.deak@intel.com
2020-10-06drm/i915: Move the initial fastset commit check to encoder hooksImre Deak
Move the checks to decide whether a fastset is possible during the initial commit to an encoder hook. This check is really encoder specific and the next patch will also require this adding a DP encoder specific check. v2: Fix negated condition in gen11_dsi_initial_fastset_check(). v3: Make sure to call the hook for all encoders on the crtc. (Ville) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201005215311.1475666-1-imre.deak@intel.com
2020-10-01drm/i915: Plumb crtc_state to link trainingVille Syrjälä
Get rid of mode crtc->config usage, and some ad-hoc intel_dp state usage by plumbing the crtc state all the way down to the link training code. Unfortunately we do have to keep some cached state in intel_dp so that we can do the "does the link need retraining?" checks from the short hpd handler. v2: Add intel_crtc_state forward declaration v3: Don't kill the PHY test code totally since it's now in the hotplug work where we can get at the states v4: Don't resurrect the debug scrambling disable bit (Imre) Use intel_dp_mst_is_master_trans() (Imre) Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com
2020-10-01drm/i915: Make intel_dp_process_phy_request() staticVille Syrjälä
intel_dp_process_phy_request() has no business being externally visible. Make it static. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-4-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
2020-09-24drm/i915: Decouple intel_dp_{min,output}_bpp() from crtc_stateVille Syrjälä
Pass the output_format directly to intel_dp_{min,output}_bpp() rather than passing in the crtc_state and digging out the output_format inside the functions. This will allow us to reuse the functions for mode validation purposes. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200917214335.3569-2-ville.syrjala@linux.intel.com Reviewed-by: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
2020-09-17drm/i915: Configure DP 1.3+ protocol converted HDMI modeVille Syrjälä
DP 1.3 adds some extra control knobs for DP->HDMI protocol conversion. Let's use that to configure the "HDMI mode" (ie. infoframes vs. not) based on the capabilities of the sink. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-13-ville.syrjala@linux.intel.com Reviewed-by: Lyude Paul <lyude@redhat.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2020-09-11Merge drm/drm-next into drm-intel-next-queuedRodrigo Vivi
Sync drm-intel-gt-next here so we can have an unified fixes flow. Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
2020-09-01drm/i915: Factor out HDCP shim functions from dp for use by dp_mstSean Paul
These functions are all the same for dp and dp_mst, so move them into a dedicated file for both sst and mst to use. Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-11-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-12-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-12-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-12-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-12-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-12-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-13-sean@poorly.run #v7 Changes in v2: -None Changes in v3: -Created intel_dp_hdcp.c for the shared functions to live (Ville) Changes in v4: -Rebased on new drm logging change Changes in v5: -None Changes in v6: -None Changes in v7: -Rebased patch Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-13-sean@poorly.run
2020-09-01drm/i915: Use ddi_update_pipe in intel_dp_mstSean Paul
In order to act upon content_protection property changes, we'll need to implement the .update_pipe() hook. We can re-use intel_ddi_update_pipe for this Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-10-sean@poorly.run #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-11-sean@poorly.run #v2 Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-11-sean@poorly.run #v3 Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-11-sean@poorly.run #v4 Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-11-sean@poorly.run #v5 Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-11-sean@poorly.run #v6 Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-12-sean@poorly.run #v7 Changes in v2: -None Changes in v3: -None Changes in v4: -None Changes in v5: -None Changes in v6: -None Changes in v7: -None Changes in v8: -None Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-12-sean@poorly.run
2020-08-31drm/i915/dp: Extract drm_dp_read_dpcd_caps()Lyude Paul
Since DP 1.3, it's been possible for DP receivers to specify an additional set of DPCD capabilities, which can take precedence over the capabilities reported at DP_DPCD_REV. Basically any device supporting DP is going to need to read these in an identical manner, in particular nouveau, so let's go ahead and just move this code out of i915 into a shared DRM DP helper that we can use in other drivers. v2: * Remove redundant dpcd[DP_DPCD_REV] == 0 check * Fix drm_dp_dpcd_read() ret checks Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-20-lyude@redhat.com
2020-08-27drm/i915/display: Disable DRRS when needed in fastsetsJosé Roberto de Souza
Changes in the configuration could cause PSR to be compatible and enabled so driver must also be able to disable DRRS when doing fastsets. v2: Fixed name of DRRS compute function (Anshuman) Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/209 Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/173 Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/209 Cc: Srinivas K <srinivasx.k@intel.com> Cc: Hariom Pandey <hariom.pandey@intel.com> Cc: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200825171331.17971-2-jose.souza@intel.com
2020-07-02drm/i915/display: prefer dig_port to reference intel_digital_portLucas De Marchi
We have a mix of dport, intel_dport, intel_dig_port and dig_port to reference a intel_digital_port struct. Numbers are around 5 intel_dport 36 dport 479 intel_dig_port 352 dig_port Since we already removed the intel_ prefix from most of our other structs, do the same here and prefer dig_port. v2: rename everything in i915, not just a few display sources and reword commit message (from Matt Roper) Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200701045054.23357-1-lucas.demarchi@intel.com
2020-06-03drm/i915: Add {preemph,voltage}_max() vfuncsVille Syrjälä
Different platforms have different max vswing/preemph settings. Turn that into a pair vfuncs so we can decouple intel_dp.c and intel_ddi.c further. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-5-ville.syrjala@linux.intel.com Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
2020-05-14drm/i915/dp: Add compute routine for DP PSR VSC SDPGwan-gyeong Mun
In order to use a common VSC SDP Colorimetry calculating code on PSR, it adds a compute routine for PSR VSC SDP. As PSR routine can not use infoframes.vsc of crtc state, it also adds new writing of DP SDPs (Secondary Data Packet) for PSR. PSR routine has its own scenario and timings of writing a VSC SDP. v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp v4: Use struct drm_device logging macros v10: 1) Fix packing of VSC SDP where Pixel Encoding/Colorimetry Format is not supported. 2) Change a checking of PSR state. Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-14-gwan-gyeong.mun@intel.com
2020-05-14drm/i915: Program DP SDPs with computed configsGwan-gyeong Mun
In order to use computed config for DP SDPs (DP VSC SDP and DP HDR Metadata Infoframe SDP), it replaces intel_dp_vsc_enable() function and intel_dp_hdr_metadata_enable() function to intel_dp_set_infoframes() function. And it removes unused functions. Before: intel_dp_vsc_enable() and intel_dp_hdr_metadata_enable() compute sdp configs and program sdp registers on enable callback of encoder. After: It separates computing of sdp configs and programming of sdp register. The compute config callback of encoder calls computing sdp configs. The enable callback of encoder calls programming sdp register. v3: Rebased v5: Polish commit message [Uma] v10: Rebased Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-8-gwan-gyeong.mun@intel.com
2020-05-14drm/i915/dp: Read out DP SDPsGwan-gyeong Mun
It adds code to read the DP SDPs from the video DIP and unpack them into the crtc state. It adds routines that read out DP VSC SDP and DP HDR Metadata Infoframe SDP In order to unpack DP VSC SDP, it adds intel_dp_vsc_sdp_unpack() function. It follows DP 1.4a spec. [Table 2-116: VSC SDP Header Bytes] and [Table 2-117: VSC SDP Payload for DB16 through DB18] In order to unpack DP HDR Metadata Infoframe SDP, it adds intel_dp_hdr_metadata_infoframe_sdp_unpack(). And it follows DP 1.4a spec. ([Table 2-125: INFOFRAME SDP v1.2 Header Bytes] and [Table 2-126: INFOFRAME SDP v1.2 Payload Data Bytes - DB0 through DB31]) and CTA-861-G spec. [Table-42 Dynamic Range and Mastering InfoFrame]. A naming rule and style of intel_read_dp_sdp() function references intel_read_infoframe() function of intel_hdmi.c v2: Minor style fix v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp v4: Use struct drm_device logging macros v5: Addressed review comments from Uma - Polish commit message and comments - Combine the if checks of sdp.HB2 and sdp.HB3 - Add 6bpc to unpacking of VSC SDP Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-3-gwan-gyeong.mun@intel.com
generated by cgit v1.2.3-70-g09d2 (git 2.48.1) at 2025-07-21 07:16:21 +0000