| Age | Commit message (Collapse) | Author |
|---|
|
DG1 shares some workarounds with TGL and RKL and also has some
additional workarounds of its own.
v2: Correct location of Wa_1408615072 (JohnH).
v3: Apply WAs 1606700617, 18011464164 and 22010931296 to DG1 (José)
v4 (Anusha)
- Add Wa_22010271021
- s/Wa_14010096844/Wa_1409836686
v5:
- Extend Wa_14010919138 to all revs (Matt Atwood)
- Power gate media is global gen12 design. (Rodrigo)
- Rebase (Lucas)
v6: use REG_BIT() to fix checkpatch warning (Lucas)
BSpec: 53508
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-8-lucas.demarchi@intel.com
|
|
Add support to load DMC v2.0.2 on DG1
While we're at it, make TGL use the same GEN12 firmware size definition
and remove obsolete comment.
Bpec: 49230
v2: do not replace GEN12_CSR_MAX_FW_SIZE (from José)
and replace stale comment
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-7-lucas.demarchi@intel.com
|
|
Add DG1 DPLL Enable register macro and use the macro to enable the
correct DPLL based on PLL id. Although we use
_MG_PLL1_ENABLE/_MG_PLL2_ENABLE these are rather combo phys.
While at it, fix coding style: wrong newlines and use if/else chain
v2: Rewrite original patch from Aditya Swarup based on refactors
upstream
Bspec: 49443, 49206
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Aditya Swarup <aditya.swarup@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-6-lucas.demarchi@intel.com
|
|
Add entries for dg1 plls and setup dg1_pll_mgr to reuse ICL callbacks.
Initial setup for shared dplls DPLL0/1 for DDIA/DDIB and DPLL2/3 for
DDI-TC1/DDI-TC2. Configure dpll cfgcrx registers to drive the plls on
DG1.
v2 (Lucas): Reword commit message and add missing update_ref_clks hook
(requested by Matt Roper)
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-5-lucas.demarchi@intel.com
|
|
DG1 has 4 DPLLs where DPLL0 and DPLL1 drive DDIA/B and
DPLL2 and DPLL3 drive DDI-TC1/DDI-TC2.
Introduce DG1_DPLL_CFCRx() helper macros to configure
DPLL registers.
Bspec: 50288, 50299
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-4-lucas.demarchi@intel.com
|
|
TGL power wells can be re-used for DG1 with the exception of the fake
power well for TC_COLD.
v2: use logic to skip power wells while copying instead of duplicating
the definition of TGL power wells (Matt Roper)
Bspec: 49182
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-3-lucas.demarchi@intel.com
|
|
The skus guarded by IS_CNL_WITH_PORT_F() have port F and thus they need
those power wells. The others don't have those. Up to now we were
just overriding the number of power wells on !IS_CNL_WITH_PORT_F(),
relying on those power wells to be the last ones. Now that we have logic
in place to skip power wells by id, use it instead.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-2-lucas.demarchi@intel.com
|
|
This allows us to skip power wells on a platform allowing it to re-use
the table from another one instead of having to create a new table from
scratch that is basically a copy with a few removals.
Cc: Imre Deak <imre.deak@intel.com>
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
[ Adapt ignore logic to be based on pw id rather than adding a new
field, as suggested by Imre ]
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-1-lucas.demarchi@intel.com
|
|
Recently we came across requirement to identify EHL and JSL
platform to program them differently. Thus Split the basic
platform definition, macros, and PCI IDs to differentiate
between EHL and JSL platforms. Also, IS_ELKHARTLAKE is replaced
with IS_JSL_EHL everywhere.
Changes since V1 :
- Rebased to avoid merge conflicts
- Added missed check for jasperlake in intel_uc_fw.c
Cc : Matt Roper <matthew.d.roper@intel.com>
Cc : Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013192948.63470-1-tejaskumarx.surendrakumar.upadhyay@intel.com
|
|
BOE panel with ID 2270 claims both PWM_PIN_CAP and AUX_SET_CAP backlight
control bits, but default chip backlight failed to control brightness.
Check AUX_SET_CAP and proceed to check quirks or VBT backlight type.
DPCD can control the brightness of this pannel.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009085750.88490-1-aaron.ma@canonical.com
|
|
In commit 79946723092b ("drm/i915: Assume 100% brightness when not in
DPCD control mode"), we fixed the brightness level when DPCD control was
not active to max brightness. This is as good as we can guess since most
backlights go on full when uncontrolled.
However in doing so we changed the semantics of the initial
'backlight.enabled' value. At least on Pixelbooks, they were relying
on the brightness level in DP_EDP_BACKLIGHT_BRIGHTNESS_MSB to be 0 on
boot such that enabled would be false. This causes the device to be
enabled when the brightness is set. Without this, brightness control
doesn't work. So by changing brightness to max, we also flipped enabled
to be true on boot.
To fix this, make enabled a function of brightness and backlight control
mechanism.
Fixes: 79946723092b ("drm/i915: Assume 100% brightness when not in DPCD control mode")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Kevin Chowski <chowski@chromium.org>>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200918002845.32766-1-sean@poorly.run
|
|
When the number of potential color planes grew to 4 we stopped
setting all unused color plane offsets to ~0xfff. The code
still tries to do this, but actually does nothing since the
loop limits are bogus.
skl_check_main_surface() actually depends on this ~0xfff
behaviour as it will make sure to move the main surface
offset below the aux surface offset because the hardware
AUX_DIST must be a non-negative value [1], and for simplicity
it doesn't bother checking if the AUX plane is actually
needed or not. So currently it may end up shuffling the
main surface around based on some stale leftover AUX offset.
The skl+ plane code also just blindly calculates the AUX_DIST
whether or not the AUX plane is actually needed by the hw or
not, and that too will now potentially use some stale AUX
surface offset in the calculation. Would seem nicer to
guarantee a consistent non-negative AUX_DIST always.
So bring back the original ~0xfff offset behaviour for
unused color planes. Though it doesn't seem super likely
that this inconsistency would cause any real issues.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Fixes: 2dfbf9d2873a ("drm/i915/tgl: Gen-12 display can decompress surfaces compressed by the media engine")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008101608.8652-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 79148ce4b25d418327feca8abb2f7392d49f5259)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The HDMI vs. not-HDMI check got inverted whem the bogus encoder->type
checks were eliminated. So now we're using 0 as the link rate on DP
and potentially non-zero on HDMI, which is exactly the opposite of
what we want. The original bogus check actually worked more correctly
by accident since if would always evaluate to true. Due to this we
now always use the RBR/HBR1 vswing table and never ever the HBR2+
vswing table. That is probably not a good way to get a high quality
signal at HBR2+ rates. Fix the check so we pick the right table.
Cc: stable@vger.kernel.org
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 94641eb6c696 ("drm/i915/display: Fix the encoder type check")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930223642.28565-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
(cherry picked from commit 945b18fb4803b01e822ade6aef6cc0b6e4bd644f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The DP Standard's recommendation is to use the LTTPR non-transparent
mode link training if LTTPRs are detected, so let's do this.
Besides power-saving, the advantages of this are that the maximum number
of LTTPRs can only be used in non-transparent mode (the limit is 5-8 in
transparent mode), and it provides a way to narrow down the reason for a
link training failure to a given link segment. Non-transparent mode is
probably also the mode that was tested the most by the industry.
The changes in this patchset:
- Pass the DP PHY that is currently link trained to all LT helpers, so
that these can access the correct LTTPR/DPRX DPCD registers.
- During LT take into account the LTTPR common lane rate/count and the
per LTTPR-PHY vswing/pre-emph limits.
- Switch to LTTPR non-transparent LT mode and train each link segment
according to the sequence in DP Standard v2.0 (complete CR/EQ for
each segment before continuing with the next segment).
v2:
- Switch to non-transparent mode during connector detection, which is
required before reading the per-PHY LTTPR capabilities.
- Move the DP_PHY_LTTPR() macro to drm_dp_helper.h (Ville)
- Use the new drm_dp_dpcd_read_phy_link_status() instead of adding the
same logic to intel_dp_get_link_status(). (Ville)
- Make intel_dp_lttpr_phy_caps() return a pointer to the whole array
instead of a pointer to its first element. (Ville)
- Add the intel_dp_phy_is_downstream_of_source() helper. (Ville)
- Add a code comment about the disable->enable quirk of
non-transparent mode.
- Add the intel_dp_training_pattern_set_reg() helper.
- Fix checkpatch/sparse warns.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-7-imre.deak@intel.com
|
|
By default LTTPRs should be in transparent link training mode,
nevertheless in this patch we switch to this default mode explicitly.
The DP Standard recommends this, supposedly because an LTTPR may be left
in the non-transparent mode (by BIOS, previous kernel, or after reset
due to a firmware bug). I haven't seen this happening, but let's follow
the DP Standard.
v2:
- Add a code comment about the explicit disabling of non-transparent
mode.
v3:
- Move check to prevent initing LTTPRs on eDP to init_dp_lttpr_init().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-6-imre.deak@intel.com
|
|
To prepare for a follow-up LTTPR change factor out a helper to disable
the training pattern in DPCD. We'll need to do this for each LTTPR
(without programming the port to output the idle pattern) when training
in LTTPR non-transparent mode.
While at it also move the disable-link-training logic from
intel_dp_set_link_train() to intel_dp_stop_link_train(), since the
latter is the only user of this.
v2:
- Move the disable-link-training logic to intel_dp_stop_link_train()
(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-4-imre.deak@intel.com
|
|
Split the prepare, link training, fallback-handling steps into their own
functions for clarity and as a preparation for the upcoming LTTPR
changes.
While at it also:
- Unexport and inline intel_dp_set_idle_link_train(), which is used at a
single place.
- Add some documentation to functions that are exported or that can use
a better description about which part of the LT sequence they
implement.
v2: (Ville)
- Unexport/inline intel_dp_set_idle_link_train()
- Make the documentation of
intel_dp_prepare_link_train()/intel_dp_stop_link_train() more accurate
wrt. HW specific details.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-3-imre.deak@intel.com
|
|
An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.
Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.
v2:
- Use a helper instead of open-coding the masking. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
Propagated from drm-intel-next-queued:
- Fix CRTC state checker (Ville)
Propated from drm-intel-gt-next:
- Avoid implicit vmpa for highmem on 32b (Chris)
- Prevent PAT attriutes for writecombine if CPU doesn't support PAT (Chris)
- Clear the buffer pool age before use. (Chris)
- Fix error code (Dan)
- Break up error capture compression loops (Chris)
- Fix uninitialized variable in context_create_request (Maarten)
- Check for errors on i915_vm_alloc_pt_stash to avoid NULL dereference (Matt)
- Serialize debugfs i915_gem_objects with ctx->mutex (Chris)
- Fix a rebase mistake caused during drm-intel-gt-next creation (Chris)
- Hold request reference for canceling an active context (Chris)
- Heartbeats fixes (Chris)
- Use usigned during batch copies (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002182610.GA2204465@intel.com
|
|
Another step towards PSR2 selective fetch, here programming plane
selective fetch registers and MAN_TRK_CTL enabling selective fetch but
for now it is fetching the whole area of the planes.
The damaged area calculation will come as next and final step.
v2:
- removed warn on when no plane is visible in state
- removed calculations using plane damaged area in
intel_psr2_program_plane_sel_fetch()
v3:
- do not shift 16 positions the plane dst coordinates, only src is
shifted
v4:
- only setting PLANE_SEL_FETCH_CTL_ENABLE and MCURSOR_MODE in
PLANE_SEL_FETCH_CTL
v5:
- not masking bits for cursor
BSpec: 55229
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007195238.53955-3-jose.souza@intel.com
|
|
Due to the debugfs flag, has_psr2 in CRTC state could have a different
value than psr.psr2_enabled and it was causing PSR2 subfeatures(DC3CO
and selective fetch) to be set to not a expected state.
So here only taking in consideration the parameter and debugfs flag
when computing PSR state, this way the CRTC state will also have
the correct state.
intel_psr_fastset_force() was already broken as
intel_psr_compute_config() was already only enabling PSR when
psr_global_enabled() and all other PSR requirements are met.
So some changes was required in this function, now it iterates over
all connectors, if it is a eDP connector and is active force a modeset
in the CRTC driving this connector, what will cause the new PSR state
to be set based on the debugfs flag.
v2:
- end connector iterator in error cases
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007195238.53955-2-jose.souza@intel.com
|
|
For platforms without selective fetch this register is reserved so
do not write 0 to it.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007195238.53955-1-jose.souza@intel.com
|
|
This will be used in future but already adding to VBT so we are
updated with VBT changes.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008211932.24989-3-jose.souza@intel.com
|
|
BDB_GENERAL_DEFINITIONS map
This will remove the "Expected child device config size for VBT
version 235 not known" debug message seen in TGL, although this is not
fixing anything it good to keep our VBT parser updated.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008211932.24989-2-jose.souza@intel.com
|
|
Child min_brightness is obsolete from VBT 234+, instead the new
min_brightness field in the main structure should be used.
This new field is 16 bits wide, so backlight_precision_bits is needed
to check if value needs to be scaled down but it is only available in
VBT 236+ so working around it by using the also new backlight_level
in the main struct.
v2:
- missed that backlight_data->level is also obsolete
v3:
- s/backlight/brightness to better match specification
- using u16 to specify brightness level instead of a u32 : 16
BSpec: 20149
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008211932.24989-1-jose.souza@intel.com
|
|
ggtt offsets/alignments are u32 everywhere else. Don't use
a signed int for them here.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008101608.8652-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
when the hardware isn't going to use the aux plane there's no
real point in dealing with the relevant hardware restrictions.
So let's just skip all that when not necessary.
We can now also remove the offset=~0xfff behaviour for unused
color planes. Let's just zero out everyting so as to not leave
stale garbage behind to confuse people debugging the code.
v2: Explicitly set AUX_DIST to zero when there is no aux plane
Reviewed-by: Imre Deak <imre.deak@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009120028.32422-1-ville.syrjala@linux.intel.com
|
|
When the number of potential color planes grew to 4 we stopped
setting all unused color plane offsets to ~0xfff. The code
still tries to do this, but actually does nothing since the
loop limits are bogus.
skl_check_main_surface() actually depends on this ~0xfff
behaviour as it will make sure to move the main surface
offset below the aux surface offset because the hardware
AUX_DIST must be a non-negative value [1], and for simplicity
it doesn't bother checking if the AUX plane is actually
needed or not. So currently it may end up shuffling the
main surface around based on some stale leftover AUX offset.
The skl+ plane code also just blindly calculates the AUX_DIST
whether or not the AUX plane is actually needed by the hw or
not, and that too will now potentially use some stale AUX
surface offset in the calculation. Would seem nicer to
guarantee a consistent non-negative AUX_DIST always.
So bring back the original ~0xfff offset behaviour for
unused color planes. Though it doesn't seem super likely
that this inconsistency would cause any real issues.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Fixes: 2dfbf9d2873a ("drm/i915/tgl: Gen-12 display can decompress surfaces compressed by the media engine")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008101608.8652-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
As with eDP and LVDS we should also respect the power cycle
delay on DSI panels. We are not using the power sequencer
for these, and we have no optimizations around the sleep
duration, so we just msleep() the whole thing away.
Note that the ICL+ DSI code doesn't seem to have any power
off/power cycle delay handling whatsoever. The only thing it
handles is the power on delay. As that looks pretty busted
in general I won't bother dealing with it for the time being.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Just like with eDP let's wait for the power sequencer power
cycle delay before we reboot the machine, as otherwise we
can't guarantee the panel's minimum power cycle delay will
be respected.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Extend the eDP panel power cycle delay wait on reboot handling
to cover all platforms. No reason to think that VLV/CHV are
in any way special since the documentation states that the
hardware power cycle delay goes back to its default value on
reset, and that may not be enough for all panels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Currently VLV/CHV use a reboot notifier to make sure the panel
power cycle delay isn't violated across a system reboot. Replace
that with the new encoder .shutdown() hook.
And let's also stop overriding the power cycle delay with the
max value. No idea why the current code does that. The already
programmed delay should be correct.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add a new encoder hook .shutdown() which will get called at the end
of the pci .shutdown() hook. We shall use this to deal with the
panel power cycle delay issues.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
As with RKL, DG1's VBT outputs are indexed according to PHY rather than
DDI.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007002210.3678024-8-lucas.demarchi@intel.com
|
|
As with RKL, DG1's PHY C acts as a comp master for PHY D.
Bspec: 49291
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007002210.3678024-7-lucas.demarchi@intel.com
|
|
The only bit we use in PHY_MISC is DE_IO_COMP_PWR_DOWN, and the bspec
details for that bit tell us that it need only be set for PHY-A and
PHY-B. It also turns out that there isn't even an instance of the
PHY_MISC register for PHY-D on this platform. Let's extend the EHL/RKL
logic that conditionally skips PHY_MISC usage to DG1 as well.
Bspec: 50107
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007002210.3678024-6-lucas.demarchi@intel.com
|
|
Add tables to map the GMBUS pin pairs to GPIO registers and port to DDC.
From spec we have registers GPIO_CTL[1-4], so we should not do the 4->9
mapping as in ICL/TGL.
The values for VBT seem wrong in BSpec. For the current boards we
actually have a 1:1 mapping.
BSpec: 49311, 49945, 20124
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007002210.3678024-5-lucas.demarchi@intel.com
|
|
DG1 always uses a 38.4 MHz rawclk rather than the 19.2/24 MHz
frequencies on CNP+. Note that register bits associated with this
frequency confusingly use 37 for the divider field rather than 38 as you
might expect.
For simplicity, let's just assume that this 38.4 MHz frequency will hold
true for other future platforms with "fake" PCH south displays and that
the CNP-style behavior will remain for other platforms with a real PCH.
Bspec: 49950
Bspec: 49309
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007002210.3678024-2-lucas.demarchi@intel.com
|
|
Recent update in documentation defeatured eDP HBR3 for EHL and JSL.
v2:
- Remove dead code in ehl_get_combo_buf_trans()
v3:
- Rebase
BSpec: 32247
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005175447.93430-1-jose.souza@intel.com
|
|
Apply Display WA #22010492432 for combo PHY PLLs too. This should fix a
problem where the PLL output frequency is slightly off with the current
PLL fractional divider value.
I haven't seen an actual case where this causes a problem, but let's
follow the spec. It's also needed on some EHL platforms, but for that we
also need a way to distinguish the affected EHL SKUs, so I leave that
for a follow-up.
v2:
- Apply the WA at one place when calculating the PLL dividers from the
frequency and the frequency from the dividers for all the combo PLL
use cases (DP, HDMI, TBT). (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201003001846.1271151-6-imre.deak@intel.com
|
|
Atm, if a full modeset is performed during the initial modeset the link
training will happen with uninitialized max DP rate and lane count. Make
sure the corresponding encoder state is initialized by adding an encoder
hook called during driver init and system resume.
A better alternative would be to store all states in the CRTC state and
make this state available for the link re-training code. Also instead of
the DPCD read in the hook there should be really a proper sink HW
readout in place. Both of these require a bigger rework, so for now opting
for this minimal fix to make at least full initial modesets work.
The patch is based on
https://patchwork.freedesktop.org/patch/101473/?series=10354&rev=3
v2: (Ville)
- s/sanitize_state/sync_state/
- No point in calling the hook when CRTC is disabled, remove the call.
- No point in calling the hook for MST, remove it.
v3: Check only DPCD_REV to avoid clobbering intel_dp->dpcd. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005230154.1477653-1-imre.deak@intel.com
|
|
Some BIOSes set an unsupported/imprecise DP link rate (for instance on
TGL A stepping). Make sure that we do an encoder recompute and a modeset
in this case.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201003001846.1271151-4-imre.deak@intel.com
|
|
Move the checks to decide whether a fastset is possible during the
initial commit to an encoder hook. This check is really encoder specific
and the next patch will also require this adding a DP encoder specific
check.
v2: Fix negated condition in gen11_dsi_initial_fastset_check().
v3: Make sure to call the hook for all encoders on the crtc. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005215311.1475666-1-imre.deak@intel.com
|
|
The BIOS of at least one ASUS-Z170M system with an SKL I have programs
the 101b WRPLL PDIV divider value, which is the encoding for PDIV=7 with
bit#0 incorrectly set.
This happens with the
"3840x2160": 30 262750 3840 3888 3920 4000 2160 2163 2168 2191 0x48 0x9
HDMI mode (scaled from a 1024x768 src fb) set by BIOS and the
ref_clock=24000, dco_integer=383, dco_fraction=5802, pdiv=7, qdiv=1, kdiv=1
WRPLL parameters (assuming PDIV=7 was the intended setting). This
corresponds to 262749 PLL frequency/port clock.
Later the driver sets the same mode for which it calculates the same
dco_int/dco_frac/div WRPLL parameters (with the correct PDIV=7 encoding).
Based on the above, let's assume that PDIV=7 was intended and the HW
just ignores bit#0 in the PDIV register field for this setting, treating
100b and 101b encodings the same way.
While at it add the MISSING_CASE() for the p0,p2 divider decodings.
v2: (Ville)
- Add a define for the incorrect divider value.
- Emit only a debug message when detecting the incorrect divider value.
- Use fallthrough from the incorrect divider value case.
- Add the MISSING_CASE()s.
v3: Return 0 freq for incorrect divider values. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006013555.1488262-1-imre.deak@intel.com
|
|
Make lspcon_init() static since it's no longer needed outside
the compilation unit. This was correct in Kai-Heng's lspcon
patch, but I fumbled this when applying it.
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: f542d671ffce ("drm/i915: Init lspcon after HPD in intel_dp_detect()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002090446.21104-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
On HP 800 G4 DM, if HDMI cable isn't plugged before boot, the HDMI port
becomes useless and never responds to cable hotplugging:
[ 3.031904] [drm:lspcon_init [i915]] *ERROR* Failed to probe lspcon
[ 3.031945] [drm:intel_ddi_init [i915]] *ERROR* LSPCON init failed on port D
Seems like the lspcon chip on the system only gets powered after the
cable is plugged.
Consilidate lspcon_init() into lspcon_resume() to dynamically init
lspcon chip, and make HDMI port work.
v6:
- Rebase on latest for-linux-next.
v5:
- Consolidate lspcon_resume() with lspcon_init().
- Move more logic into lspcon code.
v4:
- Trust VBT in intel_infoframe_init().
- Init lspcon in intel_dp_detect().
v3:
- Make sure it's handled under long HPD case.
v2:
- Move lspcon_init() inside of intel_dp_hpd_pulse().
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/203
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200610075542.12882-1-kai.heng.feng@canonical.com
|
|
Now that we've plumbed the crtc state all the way down we can
eliminate the DP_TP_{CTL,STATUS} register offsets from intel_dp,
and instead we derive them directly from the crtc state.
And thus we can get rid of the nasty hack in intel_ddi_get_config()
which mutates intel_dp during the readout.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
Get rid of mode crtc->config usage, and some ad-hoc intel_dp state
usage by plumbing the crtc state all the way down to the link training
code.
Unfortunately we do have to keep some cached state in intel_dp so
that we can do the "does the link need retraining?" checks from
the short hpd handler.
v2: Add intel_crtc_state forward declaration
v3: Don't kill the PHY test code totally since it's
now in the hotplug work where we can get at the states
v4: Don't resurrect the debug scrambling disable bit (Imre)
Use intel_dp_mst_is_master_trans() (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com
|
|
Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-10-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-9-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
