| Age | Commit message (Collapse) | Author |
|---|
|
Move cursor_base, cursor_cntl, and cursor_size from intel_crtc
into intel_plane so that we don't need the crtc for cursor stuff
so much.
Also entirely nuke cursor_addr which IMO doesn't provide any benefit
since it's not actually used by the cursor code itself. I'm not 100%
sure what the SKL+ DDB is code is after by looking at cursor_addr so
I just make it do its checks unconditionally. If that's not correct
then we should likely replace it with somehting like
plane_state->visible.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
Implement proper two stage watermark programming for g4x. As with
other pre-SKL platforms, the watermark registers aren't double
buffered on g4x. Hence we must sequence the watermark update
carefully around plane updates.
The code is quite heavily modelled on the VLV/CHV code, with some
fairly significant differences due to the different hardware
architecture:
* g4x doesn't use inverted watermark values
* CxSR actually affects the watermarks since it controls memory self
refresh in addition to the max FIFO mode
* A further HPLL SR mode is possible with higher memory wakeup
latency
* g4x has FBC2 and so it also has FBC watermarks
* max FIFO mode for primary plane only (cursor is allowed, sprite is not)
* g4x has no manual FIFO repartitioning
* some TLB miss related workarounds are needed for the watermarks
Actually the hardware is quite similar to ILK+ in many ways. The
most visible differences are in the actual watermakr register
layout. ILK revamped that part quite heavily whereas g4x is still
using the layout inherited from earlier platforms.
Note that we didn't previously enable the HPLL SR on g4x. So in order
to not introduce too many functional changes in this patch I've not
actually enabled it here either, even though the code is now fully
ready for it. We'll enable it separately later on.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-13-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
The assumption is that the registers offsets are
identical as with skl. Also all the published
kbl firmwares support the debug registers. So
let kbl show the debug counts.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100975
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494324322-28193-1-git-send-email-mika.kuoppala@intel.com
|
|
Use memdup_user_nul() helper instead of open-coding to simplify the
code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/6baf3aa45d0b5e0fd016b508bac905ebf8443aac.1493779294.git.geliangtang@gmail.com
|
|
The void *data passed to debugfs callbacks is actually the
drm_i915_private pointer, so use it thusly and avoid the to_i915(dev)
indirection.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407194220.821-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
As we now distinguish everywhere that can call
i915_gem_retire_requests() following a successful wait_for_idle, we can
remove the duplication by moving that call into i915_gem_wait_for_idle()
itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170330145041.9005-3-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Capturing GPU state requires the device to be awake in order to read
registers. Normally, this is taken along the error handler, but for the
direct debugfs access, we cannot make assumptions about the current
device state and so either need to wake it up, or abort.
Fixes: 5a4c6f1b1b2d ("drm/i915: The return of i915_gpu_info to debugfs")
Testcase: igt/pm_rpm/debugfs-read
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170328131407.14863-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Use the incoming value from debugfs/i915_wedged to select which engines
to marked as guilty in order to force us to reset those requests
(required to quickly bypass simulated hangs).
Testcase: igt/gem_exec_capture
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170325134735.30581-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
|
|
descriptor"
A GuC context and a HW context are in no way related, so the name "GuC context descriptor"
is very unfortunate, because a new reader of the code gets overwhelmed very quickly with
a lot of things called "context" that refer to different things. We can improve legibility
a lot by simply renaming a few objects in the GuC code.
v2:
- Rebased
- s/ctx_desc_pool/stage_desc_pool
- Move some explanations to the definition of the guc_stage_desc struct (Chris)
v3:
- Calculate gemsize with less intermediate steps (Joonas)
- Use BIT() macro (Joonas)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Started adding proper teardown to guc_client_alloc, ended up removing
quite a few dead ends where errors communicating with the GuC were
silently ignored. There also seemed to be quite a few erronous
teardown actions performed in case of an error (ordering wrong).
v2:
- Increase function symmetry/proximity (Michal/Daniele)
- Fix __reserve_doorbell accounting for high priority (Daniele)
- Call __update_doorbell_desc! (Daniele)
- Isolate __guc_{,de}allocate_doorbell (Michal/Daniele)
v3:
- "Select" a cacheline is a more accurate verb than "reserve" (Daniele).
- We cannot update & create the doorbell without reserving it first, so
move the whole doorbell creation for execbuf_client to the submission
enable (Oscar).i
- Add a fixme for ignoring possible doorbell destroy errors.
v4:
- Remove comment about is_high_priority (Daniele)
- Debug message typo (Daniele)
- Reuse __get_doorbell in more places (Daniele)
- Do not do arithmetic on void pointers (Daniele)
- Add comment to __reset_doorbell (Daniele)
v5:
- gccisms like arithmetic on void pointers are not frowned upon (Oscar)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
|
|
The set of available structs is not protected by the spinlock, and for
the single read we can use READ_ONCE instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323101944.21627-7-chris@chris-wilson.co.uk
|
|
Use find-first-set bitop to quickly scan through the fw_domains mask and
skip iterating over unused domains.
v2: Move the WARN into the caller, to prevent compiler warnings in
normal builds.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323101944.21627-4-chris@chris-wilson.co.uk
|
|
Storing the position of the breadcrumb of the last retired request as
a separate last_retired_head is superfluous as we always copy that into
head prior to recalculation of the intel_ring.space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170321102552.24357-1-chris@chris-wilson.co.uk
|
|
i915_gem_stolen_list_info() sneakily takes advantage of the
obj->obj_exec_link to save itself from having to allocate. Enough of the
subterfuge, just allocate an array of pointers and sort them instead of
the list.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170316132006.7976-7-chris@chris-wilson.co.uk
|
|
Provide some serialisation between user operations by waiting for the
reset initiated by setting i915_wedged to complete.
The automatic wait here makes
echo 1 > i915_wedged; cat i915_error_state
do the right thing, and not risk reporting "No error collected".
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170316171305.12972-4-chris@chris-wilson.co.uk
|
|
I915_RESET_IN_PROGRESS is being used for both signaling the requirement
to i915_mutex_lock_interruptible() to avoid taking the struct_mutex and
to instruct a waiter (already holding the struct_mutex) to perform the
reset. To allow for a little more coordination, split these two meaning
into a couple of distinct flags. I915_RESET_BACKOFF tells
i915_mutex_lock_interruptible() not to acquire the mutex and
I915_RESET_HANDOFF tells the waiter to call i915_reset().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170316171305.12972-1-chris@chris-wilson.co.uk
|
|
Use intel_rc6_residency to get benefit for increased resolution
in byt/chv.
v2: output raw and time (Chris)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
The trouble we have is that we can't really test all the shrinker
recursion stuff exhaustively in BAT because any kind of thrashing
stress test just takes too long.
But that leaves a really big gap open, since shrinker recursions are
one of the most annoying bugs. Now lockdep already has support for
checking allocation deadlocks:
- Direct reclaim paths are marked up with
lockdep_set_current_reclaim_state() and
lockdep_clear_current_reclaim_state().
- Any allocation paths are marked with lockdep_trace_alloc().
If we simply mark up our debugfs with the reclaim annotations, any
code and locks taken in there will automatically complete the picture
with any allocation paths we already have, as long as we have a simple
testcase in BAT which throws out a few objects using this interface.
Not stress test or thrashing needed at all.
v2: Need to EXPORT_SYMBOL_GPL to make it compile as a module.
v3: Fixup rebase fail (spotted by Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170312205340.16202-1-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
i915_drpc_info missed covering a few register read with the runtime pm
wakelock. Be simple and cover the entire function with a single wakelock
so that new additions are not similarly missed in future.
WARNING: CPU: 2 PID: 1334 at drivers/gpu/drm/i915/intel_drv.h:1743 gen6_read32+0x192/0x1e0 [i915]
RPM wakelock ref not held during HW access
Modules linked in: rpcsec_gss_krb5 nfsv4 dns_resolver netconsole nfsd auth_rpcgss ipmi_watchdog ipmi_poweroff ipmi_devintf ipmi_msghandler overlay btrfs xor raid6_pq dm_mod sg sd_mod snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic ata_generic pata_acpi intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_intel kvm_intel snd_hda_codec kvm eeepc_wmi irqbypass snd_hda_core crct10dif_pclmul crc32_pclmul crc32c_intel asus_wmi sparse_keymap ghash_clmulni_intel snd_hwdep i915 rfkill ppdev pcbc aesni_intel ata_piix crypto_simd glue_helper snd_pcm pata_via cryptd pcspkr snd_timer drm_kms_helper syscopyarea snd sysfillrect libata sysimgblt fb_sys_fops soundcore shpchp drm wmi parport_pc parport tpm_infineon video
CPU: 2 PID: 1334 Comm: php5 Not tainted 4.10.0-rc8-01615-g1f58c8e #1
Hardware name: System manufacturer System Product Name/P8H67-M PRO, BIOS 1002 04/01/2011
Call Trace:
dump_stack+0x63/0x8a
__warn+0xcb/0xf0
warn_slowpath_fmt+0x4f/0x60
? seq_vprintf+0x35/0x50
gen6_read32+0x192/0x1e0 [i915]
i915_drpc_info+0x55d/0x990 [i915]
seq_read+0xf2/0x3b0
full_proxy_read+0x51/0x80
__vfs_read+0x28/0x130
? security_file_permission+0x9b/0xc0
? rw_verify_area+0x4e/0xb0
vfs_read+0xa8/0x170
SyS_read+0x46/0xa0
entry_SYSCALL_64_fastpath+0x1a/0xa9
RIP: 0033:0x7fd97bf175a0
RSP: 002b:00007ffdf730db68 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
RAX: ffffffffffffffda RBX: 00007fd978028738 RCX: 00007fd97bf175a0
RDX: 0000000000002000 RSI: 00007fd97740e0d8 RDI: 0000000000000005
RBP: 0000000000000001 R08: 0000000000e97840 R09: 00007fd977ef8d58
R10: 0000000000000027 R11: 0000000000000246 R12: 00007fd977ef8d58
R13: 0000000000000000 R14: 0000000000eb4640 R15: 0000000000000000
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170313095617.29010-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
"pm_intr_keep" is not conveying the intent that it is bitmask
of interrupts that must be zero(mbz) in GEN6_PMINTRMSK.
Name it "pm_intrmsk_mbz".
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489199821-6707-2-git-send-email-sagar.a.kamble@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Sometimes we want to explicitly page out all available objects from igt,
i.e. call i915_gem_shrink_all() and check that subsequent operations
succeed. This adds DROP_SHRINK_ALL [0x8] to the set of flags for
debugfs/i915_drop_caches for that purpose.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308144622.23194-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
There is no easily digestible single self-refresh status bit, so don't
report one for debugfs/i915_sr_status on gen9+. For the moment this
avoids a read of the non-existent WM1_LP_ILK register.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309142049.16033-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
While at it also try to reduce the locking a bit to what's really just
needed instead of everything that we could possibly lock.
Added a new for_each_intel_connector_iter which includes the cast to
intel_connector.
Otherwise just plain transformation with nothing special going on.
v2: Review from Maarten:
- Stick with modeset_lock_all in sink_crc, it looks at crtc->state.
- Fix up early loop exit in i915_displayport_test_active_write.
v3: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-1-daniel.vetter@ffwll.ch
|
|
Backmerge drm-next to get at all the good stuff in drm-misc. We need
that because:
- drm_connector_list_iter conversion for i915 needs the core patches.
- Maarten's patches to use the new atomic state iterators also need
the core patches.
- We need the new link status property to complete the DP retraining
work, merging through 2 branches wasn't a good idea and we had to
partially backtrack.
- Chris needs reservation_object_trylock and we want to roll out
kref_read everywhere.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-next
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
|
|
In order for the missed-irq update to take effect, the device must be
idle. So when the user updates the fault injection via debugfs, idle the
device.
v2: Idle is explicitly required for setting test_irq, and good behaviour
for clearing the missed_irq.
v3: Use matching types; expanding to more than ulong rings is left as an
exercise to the reader.
Testcase: igt/drv_missed_irq
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307155908.14576-1-chris@chris-wilson.co.uk
|
|
As we now take the breadcrumbs spinlock within the interrupt handler, we
wish to minimise its hold time. During the interrupt we do not care
about the state of the full rbtree, only that of the first element, so
we can guard that with a separate lock.
v2: Rename first_wait to irq_wait to make it clearer that it is guarded
by irq_lock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303190824.1330-1-chris@chris-wilson.co.uk
|
|
Check timer_pending() as well as work_pending() to see if the timer for
the hangcheck has already expired and the work is pending execution on
some list somewhere.
v2: Use a more compact if-chain
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303090056.19973-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
|
|
Adding to the tail of the client request list as the only other user is
in the throttle ioctl that iterates forwards over the list. It only
needs protection against deletion of a request as it reads it, it simply
won't see a new request added to the end of the list, or it would be too
early and rejected. We can further reduce the number of spinlocks
required when throttling by removing stale requests from the client_list
as we throttle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302122525.19675-1-chris@chris-wilson.co.uk
|
|
Whilst investigating some mysterious failures with hangcheck not running
during gem_busy/basic-hang-default, the question is why did we decide to
cancel the retire_work (which queues the hangcheck)? That decision is
based around GT activity, so include that information in the debug
report.
v2: Include the GT awake status in the error state
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302150356.9713-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
|
|
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so no need to do this explicitly. Additionally it
uses debugfs_remove_recursive() to clean up the debugfs files,
so no need for adding fake drm_info_node entries.
Cc: daniel.vetter@intel.com
Cc: jani.nikula@linux.intel.com
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-20-noralf@tronnes.org
|
|
Replace the global device seqno with one for each engine, and account
for in-flight seqno on each separately. This is consistent with
dma-fence as each timeline has separate fence-contexts for each engine
and a seqno is only ordered within a fence-context (i.e. seqno do not
need to be ordered wrt to other engines, just ordered within a single
engine). This is required to enable request rewinding for preemption on
individual engines (we have to rewind the global seqno to avoid
overflow, and we do not have to rewind all engines just to preempt one.)
v2: Rename active_seqno to inflight_seqnos to more clearly indicate that
it is a counter and not equivalent to the existing seqno. Update
functions that operated on active_seqno similarly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170223074422.4125-3-chris@chris-wilson.co.uk
|
|
Handling the dynamic charp module parameter requires us to copy it for
the error state, or remember to lock it when reading (in case it used
with 0600).
v2: Use __always_inline and __builtin_strcmp
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170221162619.15954-1-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Either by chance, or by misread, the current evaluation interval may be
zero. If that is the case, don't divide by it!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170218112708.24504-1-chris@chris-wilson.co.uk
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
|
|
We don't need struct_mutex for acquiring an rpm wakeref, and do not need
to serialise those register read (it's the wrong mutex for those
registers in any case). Begone!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170218150050.10414-1-chris@chris-wilson.co.uk
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
|
|
HUC_STATUS, GUC_STATUS, SOFT_SCRATCH registers are read in debugfs
and getparam ioctl. This patch covers those accesses by RPM get/put.
v2: Covering access in i915_getparam(I915_PARAM_HUC_STATUS) (ChrisW)
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Fiedorowicz, Lukasz <lukasz.fiedorowicz@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486110513-12130-1-git-send-email-sagar.a.kamble@intel.com
|
|
Once upon a time, back in the UMS days, we supported userspace
initialising the GTT and sharing portions of the GTT with other users.
Now, we own the GTT (both global and per-process) and the tables always
start at 0 - so we can remove i915_address_space.start and forget about
this old complication.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215084357.19977-20-chris@chris-wilson.co.uk
|
|
Once upon a time before we had automated GPU state capture upon hangs,
we had intel_gpu_dump. Now we come almost full circle and reinstate that
view of the current GPU queues and registers by using the error capture
facility to snapshot the GPU state when debugfs/.../i915_gpu_info is
opened - which should provided useful debugging to both the error
capture routines (without having to cause a hang and avoid the error
state being eaten by igt) and generally.
v2: Rename drm_i915_error_state to i915_gpu_state to alleviate some name
collisions between the error state dump and inspecting the gpu state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170214164611.11381-1-chris@chris-wilson.co.uk
|
|
This adds a file in i915's debugfs directory that allows userspace to
manually control HPD storm detection. This is mainly for hotplugging
tests, where we might want to test HPD storm functionality or disable
storm detection to speed up hotplugging tests without breaking anything.
Changes since v1:
- Make HPD storm interval configurable
- Misc code cleanup
Signed-off-by: Lyude <lyude@redhat.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Tomeu Vizoso <tomeu@tomeuvizoso.net>
|
|
[12493.693827] WARNING: CPU: 1 PID: 14860 at drivers/gpu/drm/i915/intel_uncore.c:795 __unclaimed_reg_debug+0x5d/0x80 [i915]
[12493.693868] Unclaimed read from register 0x1f0024
[12493.693905] Modules linked in: vgem i915 drm_kms_helper drm intel_gtt i2c_algo_bit syscopyarea sysfillrect sysimgblt fb_sys_fops prime_numbers intel_powerclamp crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel cryptd lpc_ich i2c_i801 mfd_core video i2c_designware_platform i2c_designware_core i2c_core button autofs4 sd_mod ahci libahci libata scsi_mod [last unloaded: i915]
[12493.694039] CPU: 1 PID: 14860 Comm: intel-gpu-overl Tainted: G U 4.10.0-rc7+ #11
[12493.694079] Hardware name: GIGABYTE GB-BXBT-1900/MZBAYAB-00, BIOS F8 03/02/2016
[12493.694121] Call Trace:
[12493.694169] dump_stack+0x67/0x9d
[12493.694235] __warn+0x117/0x140
[12493.694288] warn_slowpath_fmt+0x4f/0x60
[12493.694344] ? do_raw_spin_lock+0x116/0x180
[12493.694533] ? check_for_unclaimed_mmio+0x98/0xe0 [i915]
[12493.694727] __unclaimed_reg_debug+0x5d/0x80 [i915]
[12493.694923] fwtable_read32+0x2c5/0x330 [i915]
[12493.695108] i915_interrupt_info+0xd52/0xf80 [i915]
[12493.695302] ? gen6_write16+0x310/0x310 [i915]
[12493.695357] seq_read+0x187/0x710
[12493.695412] full_proxy_read+0x75/0xc0
[12493.695472] __vfs_read+0x5a/0x220
[12493.695524] ? kmem_cache_free+0x6c/0x260
[12493.695577] ? putname+0x97/0xa0
[12493.695629] ? putname+0x97/0xa0
[12493.695682] ? rcu_read_lock_sched_held+0xb8/0xd0
[12493.695735] ? rw_verify_area+0x65/0x140
[12493.695787] vfs_read+0xd1/0x1f0
[12493.695840] SyS_read+0x62/0xc0
[12493.695893] entry_SYSCALL_64_fastpath+0x1c/0xb1
[12493.695943] RIP: 0033:0x7f82dca99ba0
[12493.695985] RSP: 002b:00007ffc0bdfd4f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[12493.696031] RAX: ffffffffffffffda RBX: 00007ffc0be005a0 RCX: 00007f82dca99ba0
[12493.696073] RDX: 0000000000001fff RSI: 00007ffc0bdfd500 RDI: 000000000000001a
[12493.696115] RBP: ffffffff810fb639 R08: 302f6972642f6775 R09: 00007f82dca0999a
[12493.696157] R10: 00007f82dcd62760 R11: 0000000000000246 R12: ffff880069a17f98
[12493.696199] R13: 00007ffc0bdfd428 R14: 0000000000000003 R15: 00007ffc0bdfd428
[12493.696250] ? trace_hardirqs_off_caller+0xd9/0x130
[12493.696300] ---[ end trace 52ccf4d39793cc59 ]---
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99761
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210133632.16946-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
Introduce intel_cdclk state which for now will track the cdclk
frequency, the vco frequency and the reference frequency (not sure we
want the last one, but I put it there anyway). We'll also make the
.get_cdclk() function fill out this state structure rather than
just returning the current cdclk frequency.
One immediate benefit is that calling .get_cdclk() will no longer
clobber state stored under dev_priv unless ex[plicitly told to do
so. Previously it clobbered the vco and reference clocks stored
there on some platforms.
We'll expand the use of this structure to actually precomputing the
state and whatnot later.
v2: Constify intel_cdclk_state_compare()
v3: Document intel_cdclk_state_compare()
v4: Deal with i945gm_get_cdclk()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207183345.19763-1-ville.syrjala@linux.intel.com
|
|
Macro seems to do exactly the same thing.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1486559530-15141-1-git-send-email-joonas.lahtinen@linux.intel.com
|
|
Alongside the hw capabilities, it is useful to know which of those have
been overridden by the user setting module parameters.
v2: Use __always_inline and BUILD_BUG magic
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170206213608.31328-4-chris@chris-wilson.co.uk
|
|
The write to the punit may fail, so propagate the error code back to its
callers. Of particular interest are the RPS writes, so add appropriate
user error codes and logging.
v2: Add DEBUG for failed frequency changes during RPS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126101919.13211-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
The intel_dp_autotest_video_pattern() function gets invoked through the
compliance test handler on a HPD short pulse if the test type is
set to DP_TEST_VIDEO_PATTERN. This performs the DPCD registers
reads to read the requested test pattern, video pattern resolution,
frame rate and bits per color value. The results of this analysis
are handed off to userspace so that the userspace app can set the
video pattern mode appropriately for the test result/response.
When the test is requested with specific BPC value, we read the BPC
value from the DPCD register. If this BPC value in intel_dp structure
has a non-zero value and we're on a display port connector, then we use
the value to calculate the bpp for the pipe. Also in this case if its
a 18bpp video pattern request, then we force the dithering on pipe to be
disabled since it causes CRC mismatches.
The compliance_test_active flag is set at the end of the individual
test handling functions. This is so that the kernel-side operations
can be completed without the risk of interruption from the userspace
app that is polling on that flag.
v5:
* Remove test_result variable
* Populate the compliance test data at the end of the function (Jani Nikula)
v4:
*Return TEST_NAK on read failures and invalid values (Jani Nikula)
* Address CRC mismatch errors
v3:
* Use the updated properly shifted bit definitions (Jani Nikula)
* Force dithering to be disabled on 18bpp compliance
test request (Manasi Navare)
v2:
* Updated the DPCD Register reads based on proper defines in header (Jani Nikula)
* Squahsed the patch that forced the pipe bpp to compliance test bpp (Jani Nikula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274909-17470-1-git-send-email-manasi.d.navare@intel.com
|
|
This patch addresses a few issues from the original patch for
DP Compliance EDID test support submitted by
Todd Previte<todd.previte@gmail.com>
Video Mode requested in the EDID test handler for the EDID Read
test (CTS 4.2.2.3) should be set to PREFERRED as per the CTS spec.
v2:
* Added read debugfs data from test_data.edid if its EDID test (Jani NIkula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484968170-12467-3-git-send-email-manasi.d.navare@intel.com
|
|
Along with GLK it was introduced the .is_lp and IS_GEN9_LP.
So, following the same simplification standard we can
put Skylake and Kabylake under the same bucket for most
of the things.
So let's add the IS_GEN9_BC for "Big Core" (non Atom based
platforms).
The i915_drv.c was let out of this patch on purpose
because that is really a decision per platform, just like
other cases where IS_KABYLAKE is different from IS_SKYLAKE.
v2: fix conflict with IS_LP and 3 new cases for this
big core bucket:
- intel_ddi.c: intel_ddi_get_link_dpll
- intel_fbc.c: find_compression_threshold
- i915_gem_gtt.c: gtt_write_workarounds
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485196357-30599-2-git-send-email-rodrigo.vivi@intel.com
|
|
We need to prevent resubmission of the context immediately following an
initial resubmit (which does a lite-restore preemption). Currently we do
this by disabling all submission whilst the context is still active, but
we can improve this by limiting the restriction to only until we
receive notification from the context-switch interrupt that the
lite-restore preemption is complete.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124110009.28947-2-chris@chris-wilson.co.uk
|
|
Add debugfs entry for HuC loading status check.
v2: rebased on top of drm-tip.
Cc: Michal wajdeczko <michal.wajdeczko@intel.com>
Tested-by: Xiang Haihao <haihao.xiang@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484755558-1234-4-git-send-email-anusha.srivatsa@intel.com
|
|
Appease both the poor reader and the compiler by rewriting the string
lookup for EDP_PSR2_STATUS_CTL:
drivers/gpu/drm/i915/i915_debugfs.c:2662 i915_edp_psr_status() warn: if statement not indented
Fixes: 6ba1f9e1772f ("drm/i915/psr: report live PSR2 State")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Cc: Patil Deepti <deepti.patil@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170116130622.20369-1-chris@chris-wilson.co.uk
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
