| Age | Commit message (Collapse) | Author |
|---|
|
The dpi_display_enable() function ensures that a VDDS_DSI regulator is
available if the DSI uses the VDDS_DSI supply. This is not needed, as a
failure to get the VDDS_DSI supply will result in a probe failure,
dpi_display_enable() will thus never be called in that case.
Remove the check, and replace tests for the FEAT_DPI_USES_VDDS_DSI
feature with a test for the regulator object.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Remove DPI's legacy data_lines code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The DPI platform driver was used for non-DT platforms only. On DT
platforms the DPI port is handled manually. As OMAP display devices are
now instantiated from DT only, remove the DPI platform driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The OMAP driver has its own OF graph helpers that are similar to the
common helpers. This commit replaces most of the calls with the common
helpers. There's still a couple of custom helpers left, but the driver
needs more extensive changes to get rid of them.
In dss_init_ports, we invert the loop, looping through the known ports
and matching them to DT nodes rather than looping thru DT nodes and
matching them to the ports.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
|
|
The clock source selection for the LCD outputs is too hardcoded at the
moment. For example, LCD3 is set to use PLL2_1, and PLL2 doesn't exist
on DRA72x SoCs.
There are quite many ways to configure the clocks, even using HDMI PLL
for LCD outputs, but enabling full configuration of the clocks is rather
tricky.
This patch improves the situation a bit by checking if the PLL about to
be used exists, and if not, tries another one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The driver only uses even dividers for hsdiv when pclk >= 100MHz, as odd
dividers can create uneven duty cycle. However, while this holds true
for some dividers like DISPC's LCK and PCK dividers, it is not actually
true for hsdiv.
hsdiv always produces even duty cycle, so the constraint can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Use 'vm' to refer to a struct videomode instead of 'p', 't', 'timings' or
something else.
The code will be easier to follow if we use consistent names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omap_video_timings can be replaced with the generic videomode in omapdrm
and the omap_video_timings can be removed.
This patch will replace the omap_video_timings with videomode.
With the change we no longer need the functions to convert to/from
videomode and drm_display_mode to omap_video_timings, these can be removed
as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omap_video_timings struct have the same members as struct videomode, but
their types are different. As first step change the types of the
omap_video_timings struct members to match their counterpart in
struct videomode to catch any type cast related issues.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
In preparation to move the stack to use the generic videmode struct for
display timing information rename the x_res member to hactive.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Merge omapdss public header refactoring, which separates the public
header into omapdrm and omapfb parts.
|
|
All drivers to include the omapdrm/dss/omapdss.h header file. This header
includes the <video/omapdss.h>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
|
|
Originally DSS only had DSI PLLs, and thus the DPI driver has functions
and variables that refer to DSI or DSI PLL. Now we support DSI, VIDEO
and HDMI PLLs, so it's time to remove the DSI references from the code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Type A and B PLLs require a bit different calculations for the clock
rates. DPI driver supports only type A PLLs.
This patch adds support for the type B PLL.
Type B PLLs are simpler than type A, as type B can produce a good clock
for almost any rate. Thus we can just ask it to produce the pixel clock
and use one as LCK and PCK dividers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add a "_a" postfix to the type A PLL calc functions, to differentiate
them from the type B PLL calculations which we will add shortly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DPI driver uses a fixed clkout index, 0. This has worked fine as the
first clkout is usually used.
To generalize the code and to support additional clock sources, change
the code to use dss_pll_get_clkout_idx_for_src() to get the clkout
index.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We can clean up the DPI driver's clock source handling by using the
dss_clk_source instead of only a dss_pll pointer.
This will also make it possible to use additional clock sources, like
PLL1_3 or HDMI_PLL, which the code did not support earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The code to set the clock muxes for DISPC's LCD clock inputs is very
confusing. Especially on DRA7, there's an additional clock muxing that
needs to be done, which at the moment is done in dpi.c using
dss_ctrl_pll_set_control_mux().
Clean this all up by:
- Using dss_clk_source instead of dss_pll_id, as dss_pll_id doesn't
specify the clock source quite correctly.
- Splitting the dss_select_lcd_clk_source() up into DSS version specific
helper functions.
- Using dss_ctrl_pll_set_control_mux() from the helper functions, so
that dpi.c doesn't have to call it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The names of the enum dss_clk_source's values are legacy names, only
correct for OMAP3 DSS. Rename the names to more generic ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
'enum omap_dss_clk_source' is internal to dss. Let's rename it to
'dss_clk_source' match our naming convention.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes DPI driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The DSS output drivers check 'dssdev->manager' in disconnect()
functions. This check is not needed as the manager must always be set if
the output device was connected. Remove the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Both dpi and sdi check for 'mgr != NULL' in check_timings. This check is
not necessary, as mgr must always be set before check_timings. Remove
the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_enable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_lcd_config() to accept 'enum omap_channel' instead
of 'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_timings() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disconnect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_connect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use 'out->dispc_channel_connected' to check if the device is connected
to an overlay manager or not, instead of using 'out->manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DISPC requires the x resolution to be divisible by 8 when stall mode is
not used.
Add a check to the DPI driver to verify this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Now that omapfb has its own copy of omapdss and display drivers, we can
move omapdss and display drivers which omapdrm uses to omapdrm's
directory.
We also need to change the main drm Makefile so that omapdrm directory
is always entered, because omapdss has a file that can't be built as a
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
|
