| Age | Commit message (Collapse) | Author |
|---|
|
ADT7421 is similar to ADT7461A but supports configurable Beta Compensation.
Packet Error Checking (PEC) is supported but undocumented.
A devicetree node is not added for the added chip since it is quite
unlikely that such an old chip will ever be used in a devicetree based
system. It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
NCT218 is compatible to NCT72 and NCT214. It also supports PEC (packet
error checking). Similar to NCT72 and NCT214, PEC support is undocumented.
Unlike NCT214 and NCT72, NCT218 does not support the undocumented secondary
chip and manufacturer ID registers at 0x3e and 0x3f and returns 0x00 when
reading those registers. The value for the chip revision register is not
documented but was observed to be 0xca. Use that information to improve
chip detection accuracy.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
NCT214 and NCT72 are compatible to ADT7461/ADT7461A but have full
PEC (packet error checking) support. PEC support is undocumented.
Both chips support the undocumented secondary chip and manufacturer
ID registers at 0x3e and 0x3f, and return 0x61 as chip ID. Use this
information to improve the accuracy of chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Unlike ADM1023 and compatible chips, NCT210 does not support a temperature
offset register. A real chip was found to have a chip revision of 0x3f.
Use it to detect NCT210 explicitly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
LM86 and LM90 support exactly the same features, so there is no need
to keep their configuration options separate. Combine to reduce data
size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
All chips supported by the ADM1021 driver are also supported by the LM90
driver. Make that support official.
After this change, the adm1021 driver is only needed if the lm90 driver
is disabled. Also, the adm1021 driver misdetects a variety of chips as
MAX1617A, which is unwanted if any of those chips is in the system.
For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to
show that it is not needed if the lm90 driver is enabled, and to avoid
misdetection if a chip supported by the lm90 driver is in the system.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Both chips are quite similar to other chips of this series, so add
support for them to the lm90 driver. Also mention ON Semiconductor NCT210,
which is pin and register compatible to ADM1021A.
None of the chips support the secondary manufacturer and chip ID registers
at 0x3e and 0x3f, but return 0 when reading from those registers.
Use that information to improve the accuracy of chip detection code.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily
be supported by the LM90 driver. The most difficult part is chip detection,
since those old chips do not support manufacturer ID or chip ID registers.
The "alarms" attribute is enabled for both chips to match the functionality
of the adm1021 driver. Chip detection was improved and is less prone to
misdetection than the chip detection in the adm1021 driver.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Introduce 16-bit register write function to simplify the code in
some places.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Simplify the code a bit by handling single-register read operations
in lm90_read16(). All we need to do is to skip the low-byte read
operation if the register address is 0.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
MAX6642 is a reduced version of LM90 with no low limits and no conversion
rate register. Its alert functionality is broken, similar to many other
chips supported by the lm90 driver.
After this change, the stand-alone max6642 driver is only needed if the
lm90 driver is disabled. Make it dependent on SENSORS_LM90=n to show that
it is not needed if the lm90 driver is enabled.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
A flag indicating support for setting the conversion rate doesn't cost
much and will enable us to add support for MAX6642 to the lm90 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
A flag indicating support for minimum temperature limits doesn't cost much
and will enable us to add support for MAX6642 to the lm90 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
MAX6690 is all but identical to MAX6654. Revision 1 of its
datasheet lists the same chip ID as MAX6654, and a chip labeled
MAX6654 was found to have the chip ID listed as MAX6690 chip ID
in Revision 2 of its datasheet.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
ADT7461A and NCT1008 support the undocumented manufacturer and chip ID
registers at 0x3e and 0x3f, and return 0x61 as chip ID. ADM1032 and
ADT7461 do not support those registers but return 0 when reading them.
Use this information to improve the accuracy of the chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
ADT7481, ADT7482, and ADT7483 are similar to ADT7461, but support two
external temperature sensors, similar to MAX6695/6696. They support an
extended temperature range similar to ADT7461. Registers for the second
external channel can be accessed directly or by using the same method as
used by MAX6695/6696. For simplicity, the access method implemented for
MAX6695/6696 is used.
The chips support PEC (packet error checking). Set the PEC feature flag
and let the user decide if it should be enabled or not (it is by default
disabled).
Even though it is only documented for ADT7483, all three chips support a
secondary manufacturer ID register at 0x3e and a chip ID register at 0x3f.
Use the contents of those registers register for improved chip detection
accuracy. Add the same check to the ADT7461A detection code since this chip
also supports the same (undocumented) registers.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Unlike MAX6646/MAX6647/MAX6649, MAX6648 and MAX6692 only support
a temperature range of 0..127 degrees C. Separate support for the
two sets of chips to be able to support maximum temperature ranges
correctly for all chips. Introduce new feature flag to indicate
temperature support up to 255 degrees C.
Since the chips are almost identical except for the supported temperature
range, automatic chip detection is limited. Effectively this means that
MAX6648 may be mis-detected as MAX6649 when auto-detected, but there is
nothing we can do about that.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
We don't want to support the obsolete 'alarms' attribute for new
chips supported by this driver. Add flag to indicate 'alarms' attribute
support and use it for existing chips. This flag will not be set for
additional chips supported by this driver in the future.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When support for G781 was added, chips with ID 0x01 were found at I2C
addresses 0x4c and 0x4d. The G781 datasheet (version 1.3 from October 2003)
says that the device ID for G781-1 is 0x03, not 0x01. Also, the datasheet
states that the chip at I2C address is G781 and the chip at I2C address
0x4d is G781-1.
A G781-1 at I2C address 0x4d was now found to have a chip ID of 0x03
as suggested by the datasheet. Accept both 0x01 and 0x03 chip IDs at both
addresses to ensure that all variants of G781 are detected properly.
While at it, improve chip detection accuracy by reading two additional
registers and ensuring that only expected bits are set in those registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The NCT1008 datasheet, Revision 3, states that its chip revision is
0x57. This matches the ADT7461A chip revision, and NCT1008 is therefore
detected as ADT7461A. In revision 6 of the datasheet, the chip revision
register is no longer documented. Multiple samples of NCT1008 were found
to report a chip revision of 0x54. As it turns out, one of the patches
submitted to add NCT1008 support to the lm90 driver already included a
check for chip revision 0x54. Unfortunately, that patch never made it into
the kernel. Remedy the situation and explicitly detect chips with revision
0x54 as NCT1008.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The detect function is getting larger and larger and difficult to
understand or review. Split it into per-manufacturer detect functions
to improve readability.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since temperature conversion functions are now unified, there is no need
to keep "the chip supports a configurable extended temperature range" and
"the chip has extended temperature range enabled" flags separate.
Use a single flag instead to reflect both.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
While most LM90 compatible chips support a temperature sensor resolution
of 11 bit, this is not the case for all chips. ADT7461 only supports a
resolution of 10 bit, and TMP451/TMP461 support a resolution of 12 bit.
Add support for various temperature sensor resolutions. To do this,
model all temperature sensors as 16 bit sensors, and use unified
temperature conversion functions which take the sensor resolution
as parameter.
While enhancing functionality, this has the positive side effect of
reducing code size by about 5%.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When reading 16-bit volatile registers, the code uses a trick to
determine if a temperature is consistent: It reads the high part
of the register twice. If the values are the same, the code assumes
that the reading is consistent. If the value differs, the code
re-reads the second register as well and assumes that it now has
correct values.
This is only necessary for volatile registers. Add a parameter to
lm90_read16() to indicate if the register is volatile to avoid the
extra overhead for non-volatile registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
ADT7461 and TMP451 temperature sensors support extended temperature ranges.
If standard temperature range is selected, the temperature range is
unsigned and limited to 0 .. 127 degrees C. For TMP461, the standard
temperature range is -128000 ... 127000 degrees C. Distinguish between
the two chips by introducing a feature flag indicating if the standard
temperature range is signed or unsigned. Use the same flag for MAX6646/
MAX6647 as well since those chips also support unsigned temperatures.
Note that while the datasheet for ADT7461 suggests that the default
temperature range is unsigned, tests with a real chip suggest that this
is not the case: If the temperature offset is set to a value << 0,
the temperature register does report negative values.
Tests with real chips show that MAX6680/MAX6681 and SA56004 report
temperatures of 128 degrees C and higher as negative temperatures.
Add respective comments to the code.
Also use clamp_val() and DIV_ROUND_CLOSEST where appropriate in
calculations.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Experiments show that ADT7461A and NCT1008 support PEC, even though it is
not documented. Enable support for it in the driver. Since ADT7461 only
supports partial PEC, this means that the configuration for ADT7461A
needs to be separated from ADT7461.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Revision 0 of the ADT7461 datasheet suggests that the chip supports PEC
(packet error checking). This information is gone in later versions of the
datasheet. Experiments show that PEC support on ADT7461 is similar to PEC
support in ADM1032, ie it is only supported for read operations. Add
support for it to the driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
PEC (packet error checking) support for ADM1032 is currently only enabled
if the chip was auto-detected, but not if a chip is instantiated
explicitly. Always enable PEC support by introducing a chip feature flag
indicating partial PEC support. Also, for consistency, disable PEC support
by default to match existing functionality if the chip was not auto-
detected.
At the same time, introduce generic support for PEC with a separate feature
flag. This will be used when support for chips with full PEC functionality
is added.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The register write address either matches the read address, or it is the
read address plus 6. Simplify the code and resolve the write address
programmatically instead of having two defines for each register.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Handling bit shifts necessary to extract status bits during compile time
reduces code and data size by almost 5% when building for x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use BIT macro instead of shift operation to improve readability.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Reorder chip enumeration in alphabetical order to make it easier to
see which chips are supported, and to clarify where to add support
new chip types. No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Reorder include files in alphabetical order to reduce the chance of
duplicates and to make it clear where new include files should be
added. Drop the unnecessary include of linux/sysfs.h. Include
linux/device.h instead because that is what is actually used.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Many chips supported by this driver clear status registers after it
is read and update it in the next measurement cycle. Normally this falls
under the radar because all registers are only read once per measurement
cycle. However, there is an exception: Status registers are always read
during interrupt and laert handling. This can result in invalid status
reports if userspace reads an alarm attribute immediately afterwards.
Rework alarm/status handling by keeping a shadow register with 'current'
alarms, and by ensuring that the register is either only updated once per
measurement cycle or not cleared.
A second problem is related to alert handling: Alert handling is disabled
for chips with broken alert after an alert was reported, but only
re-enabled if attributes are read by the user. This means that alert
conditions may appear and disappear unnoticed. Remedy the situation
by introducing a worker to periodically read the status register(s) while
alert handling is disabled, and re-enable alerts after the alert condition
clears.
Yet another problem is that sysfs and udev events are currently only
reported to userspace if an alarm is raised, but not if an alarm condition
clears. Use the new worker to detect that situation and also generate
sysfs and udev events in that case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
So far the driver only generated sysfs and udev events for minimum and
maximum alarms. Also generate events for critical and emergency alarms.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Enabling and disabling PEC for PMBus devices is currently only supported
with a debugfs attribute, which requires debugfs to be enabled and is
thus less than perfect. Take the lm90 driver as example and add a 'pec'
attribute to the I2C device if both the I2C adapter and the PMBus device
support it. Remove the now obsolete 'pec' attribute from debugfs.
Cc: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If platform_device_add() fails, it no need to call platform_device_del(), split
platform_device_unregister() into platform_device_del/put(), so platform_device_put()
can be called separately.
Fixes: 8808a793f052 ("ibmaem: new driver for power/energy/temp meters in IBM System X hardware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220701074153.4021556-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Drop the redundant word 'the' in the comments following
/*
* Set PHASE registers on all pages to 0xff to ensure that phase
* specific commands will apply to all phases of a given page (rail).
* This only affects the READ_IOUT and READ_TEMPERATURE2 registers.
* READ_IOUT will return the sum of currents of all phases of a rail,
* and READ_TEMPERATURE2 will return the maximum temperature detected
* for the [the - DROP] phases of the rail.
*/
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622063231.20612-1-jiangjian@cdjrlc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Currently, the response to the power cap command overwrites the
first eight bytes of the poll response, since the commands use
the same buffer. This means that user's get the wrong data between
the time of sending the power cap and the next poll response update.
Fix this by specifying a different buffer for the power cap command
response.
Fixes: 5b5513b88002 ("hwmon: Add On-Chip Controller (OCC) hwmon driver")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628203029.51747-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This fixes a regression where coma lead to concatenating board names
and broke module loading for C8H.
Fixes: 5b4285c57b6f ("hwmon: (asus-ec-sensors) fix Formula VIII definition")
Signed-off-by: Michael Carns <mike@carns.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220615122544.140340-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Unbinding the driver or removing the parent device at the same time
as using the OCC active sysfs file can cause the driver to unregister
the hwmon device twice. Prevent this by locking the occ mutex in the
shutdown function.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220606185455.21126-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If no memory can be allocated, some resources still need to be released as
already done in the other error handling paths.
Fixes: 752b927951ea ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Octo")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/be6b955d50de140fcc96bd116150b435021bf567.1653225250.git.christophe.jaillet@wanadoo.fr
Reviewed-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220521111145.81697-37-Julia.Lawall@inria.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Make sure that the support of PEC is determined before the read of other
registers. Otherwise the validation of PEC can trigger an error on the read
of STATUS_BYTE or STATUS_WORD registers.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without the move of the code, at the second load of
the driver (or bind) the STATUS_BYTE or STATUS_WORD register is always
read with PEC enabled, which is likely to cause a read error resulting
with fail of a driver load (or bind).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220519233334.438621-1-dev_public@wujek.eu
Fixes: 75d2b2b06bd84 ("hwmon: (pmbus) disable PEC if not enabled")
Fixes: 4e5418f787ec5 ("hwmon: (pmbus_core) Check adapter PEC support")
[groeck: Added Fixes: tags, dropped continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Building arm:allmodconfig may fail with the following error.
In function 'fortify_memcpy_chk',
inlined from 'bitmap_copy' at include/linux/bitmap.h:261:2,
inlined from 'bitmap_copy_clear_tail' at include/linux/bitmap.h:270:2,
inlined from 'bitmap_from_u64' at include/linux/bitmap.h:622:2,
inlined from 'check_populated_dimms' at
drivers/hwmon/peci/dimmtemp.c:284:2:
include/linux/fortify-string.h:344:25: error:
call to '__write_overflow_field' declared with attribute warning:
detected write beyond size of field (1st parameter)
The problematic code is
bitmap_from_u64(priv->dimm_mask, dimm_mask);
dimm_mask is declared as u64, but the bitmap in priv->dimm_mask is only
24 bit wide. On 32-bit systems, this results in writes over the end of
the bitmap.
Fix the problem by using u32 instead of u64 for dimm_mask. This is
currently sufficient, and a compile time check to ensure that the number
of dimms does not exceed the bit map size is already in place.
Fixes: 73bc1b885dae ("hwmon: peci: Add dimmtemp driver")
Cc: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Some lm90 compatible devices can operate in an extended temperature mode.
This feature is now enabled if the property is set in the corresponding
device tree node.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220517135614.8185-2-holger.brunck@hitachienergy.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use ida_alloc()/ida_free() instead of deprecated
ida_simple_get()/ida_simple_remove() .
Signed-off-by: keliu <liuke94@huawei.com>
Link: https://lore.kernel.org/r/20220517063126.2142637-2-liuke94@huawei.com
[groeck: Updated subject to include driver name]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use ida_alloc()/ida_free() instead of deprecated
ida_simple_get()/ida_simple_remove() .
Signed-off-by: keliu <liuke94@huawei.com>
Link: https://lore.kernel.org/r/20220517063126.2142637-1-liuke94@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The ROG CROSSHAIR VIII FORMULA board has the same sensors as the
CROSSHAIR VIII HERO [1] thus let's join their definitions which adds
missing sensors for Formula.
[1] https://github.com/LibreHardwareMonitor/LibreHardwareMonitor/pull/740
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220517080508.1910953-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
