| Age | Commit message (Collapse) | Author |
|---|
|
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PF/VFs
Previously, the driver queried the firmware in order to get the number
of supported EQs. Under SRIOV, since this was done before the driver
notified the firmware how many VFs it actually needs, the firmware had
to take into account a worst case scenario and always allocated four EQs
per VF, where one was used for events while the others were used for completions.
Now, when the firmware supports the asymmetric allocation scheme, denoted
by exposing num_sys_eqs > 0 (--> MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the
QUERY_FUNC command to query the firmware before enabling SRIOV. Thus we
can get more EQs and MSI-X vectors per function.
Moreover, when running in the new firmware/driver mode, the limitation
that the number of EQs should be a power of two is lifted.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.
One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a9060d "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".
While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Last late set of InfiniBand/RDMA fixes for 3.17:
- fixes for the new memory region re-registration support
- iSER initiator error path fixes
- grab bag of small fixes for the qib and ocrdma hardware drivers
- larger set of fixes for mlx4, especially in RoCE mode"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
IB/mlx4: Fix VF mac handling in RoCE
IB/mlx4: Do not allow APM under RoCE
IB/mlx4: Don't update QP1 in native mode
IB/mlx4: Avoid accessing netdevice when building RoCE qp1 header
mlx4: Fix mlx4 reg/unreg mac to work properly with 0-mac addresses
IB/core: When marshaling uverbs path, clear unused fields
IB/mlx4: Avoid executing gid task when device is being removed
IB/mlx4: Fix lockdep splat for the iboe lock
IB/mlx4: Get upper dev addresses as RoCE GIDs when port comes up
IB/mlx4: Reorder steps in RoCE GID table initialization
IB/mlx4: Don't duplicate the default RoCE GID
IB/mlx4: Avoid null pointer dereference in mlx4_ib_scan_netdevs()
IB/iser: Bump version to 1.4.1
IB/iser: Allow bind only when connection state is UP
IB/iser: Fix RX/TX CQ resource leak on error flow
RDMA/ocrdma: Use right macro in query AH
RDMA/ocrdma: Resolve L2 address when creating user AH
mlx4: Correct error flows in rereg_mr
IB/qib: Correct reference counting in debugfs qp_stats
IPoIB: Remove unnecessary port query
...
|
|
We had several problems here. First, a race condition on QP1 mac
handling between mlx4_ib_update_qps and mlx4_ib_modify_qp, which is
fixed by taking the qp mutex in mlx4_ib_update_qps.
Also, qp->pri.smac_port was not updated in mlx4_ib_update_qps.
Last, in __mlx4_ib_modify_qp we did not properly handle the case where
the mac is zero, but port is non-zero.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Automatic Path Migration is not supported under RoCE. Therefore,
return a "not-supported" error if the caller attempts to set an
alternate path in a QP context.
In addition, if there are no IB ports configured, do not report
APM capability in the device flags returned by mlx4_ib_query_device.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
For native functions (non-SR-IOV), there's no reason to update
the smac_index, as QP1 is a GSI QP.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The source MAC is needed in RoCE when building the QP1 header.
Currently, this is obtained from the source net device. However, the net
device may not yet exist, or can be destroyed in parallel to this QP1 send
operation (e.g through the VPI port change flow) so accessing it may cause
a kernel crash.
To fix this, we maintain a source MAC cache per port for the net device in
struct mlx4_ib_roce. This cached MAC is initialized to be the default MAC
address obtained during HCA initialization via QUERY_PORT. This cached MAC
is updated via the netdev event notifier handler.
Since the cached MAC is held in an atomic64 object, we do not need locking
when accessing it.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When device is being removed (e.g during VPI port link type change
from ETH to IB), tasks for gid table changes should not be executed.
Flush the current queue of tasks and block further tasks from entering the queue.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Chuck Lever reported the following stack trace:
=================================
[ INFO: inconsistent lock state ]
3.16.0-rc2-00024-g2e78883 #17 Tainted: G E
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
(&(&iboe->lock)->rlock){+.?...}, at: [<ffffffffa065f68b>] mlx4_ib_addr_event+0xdb/0x1a0 [mlx4_ib]
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810b3110>] mark_irqflags+0x110/0x170
[<ffffffff810b4806>] __lock_acquire+0x2c6/0x5b0
[<ffffffff810b4bd9>] lock_acquire+0xe9/0x120
[<ffffffff815f7f6e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa0661084>] mlx4_ib_scan_netdevs+0x34/0x260 [mlx4_ib]
[<ffffffffa06612db>] mlx4_ib_netdev_event+0x2b/0x40 [mlx4_ib]
[<ffffffff81522219>] register_netdevice_notifier+0x99/0x1e0
[<ffffffffa06626e3>] mlx4_ib_add+0x743/0xbc0 [mlx4_ib]
[<ffffffffa05ec168>] mlx4_add_device+0x48/0xa0 [mlx4_core]
[<ffffffffa05ec2c3>] mlx4_register_interface+0x73/0xb0 [mlx4_core]
[<ffffffffa05c505e>] cm_req_handler+0x13e/0x460 [ib_cm]
[<ffffffff810002e2>] do_one_initcall+0x112/0x1c0
[<ffffffff810e8264>] do_init_module+0x34/0x190
[<ffffffff810ea62f>] load_module+0x5cf/0x740
[<ffffffff810ea939>] SyS_init_module+0x99/0xd0
[<ffffffff815f8fd2>] system_call_fastpath+0x16/0x1b
irq event stamp: 336142
hardirqs last enabled at (336142): [<ffffffff810612f5>] __local_bh_enable_ip+0xb5/0xc0
hardirqs last disabled at (336141): [<ffffffff81061296>] __local_bh_enable_ip+0x56/0xc0
softirqs last enabled at (336004): [<ffffffff8106123a>] _local_bh_enable+0x4a/0x50
softirqs last disabled at (336005): [<ffffffff810617a4>] irq_exit+0x44/0xd0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&iboe->lock)->rlock);
<Interrupt>
lock(&(&iboe->lock)->rlock);
*** DEADLOCK ***
The above problem was caused by the spin lock being taken both in the process
context and in a soft-irq context (in a netdev notifier handler).
The required fix is to use spin_lock/unlock_bh() instead of spin_lock/unlock
on the iboe lock.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When a RoCE port becomes active and the netdev of the port has upper
device (e.g bond/team), GIDs derived from the upper dev should appear
in the port's RoCE GID table.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
There's no need to reset the gid table twice and we need to do it only
for Ethernet ports. Also, no need to actively scan ndetdevs since it's
being done immediatly after we register netdev notifiers.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When reading the IPv6 addresses from the net-device, make sure to
avoid adding a duplicate entry to the GID table because of equality
between the default GID we generate and the default IPv6 link-local
address of the device.
Fixes: acc4fccf4eff ("IB/mlx4: Make sure GID index 0 is always occupied")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When Ethernet netdev is not present for a port (e.g. when the link
layer type of the port is InfiniBand) it's possible to dereference a
null pointer when we do netdevice scanning.
To fix that, we move a section of code that needs to run only when
netdev is present to a proper if () statement.
Fixes: ad4885d279b6 ("IB/mlx4: Build the port IBoE GID table properly under bonding")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
According to <http://marc.info/?t=138347640900004&r=1&w=2>, revision
A0 of Connect-X does not correctly assemble TSO packets. Disable that
feature on that hardware revision.
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Changing the vlan stripping policy of the QP isn't supported by older
firmware versions for the INIT2RTR command. Nevertheless, we've used it.
Fix that by doing this policy change using INIT2RTR only if the firmware
supports it, otherwise, we call UPDATE_QP command to do the task.
Fixes: 7677fc9 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Raw Ethernet QPs opened from user-space lack the proper setup to
recieve/handle VXLAN traffic when VXLAN offloads are enabled.
Fix that by adding a tunnel steering rule on top of the normal unicast
steering rule and set the tunnel_type field in the QP context.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'mlx4', 'mlx5', 'ocrdma' and 'srp' into for-next
|
|
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This enables the user to change the protection domain, access flags
and translation (address and length) of the MR.
Use basic mlx4_core helper functions to get, update and set MPT and
MTT objects according to the required modifications.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull main InfiniBand/RDMA updates from Roland Dreier:
- add iWARP port mapper to avoid conflicts between RDMA and normal
stack TCP connections.
- fixes for i386 / x86-64 structure padding differences (ABI
compatibility for 32-on-64) from Yann Droneaud.
- a pile of SRP initiator fixes from Bart Van Assche.
- fixes for a writeback / memory allocation deadlock with NFS over
IPoIB connected mode from Jiri Kosina.
- the usual fixes and cleanups to mlx4, mlx5, cxgb4 and other low-level
drivers.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (61 commits)
RDMA/cxgb4: Add support for iWARP Port Mapper user space service
RDMA/nes: Add support for iWARP Port Mapper user space service
RDMA/core: Add support for iWARP Port Mapper user space service
IB/mlx4: Fix gfp passing in create_qp_common()
IB/umad: Fix use-after-free on close
IB/core: Fix kobject leak on device register error flow
RDMA/cxgb4: add missing padding at end of struct c4iw_alloc_ucontext_resp
mlx4_core: Fix GFP flags parameters to be gfp_t
IB/core: Fix port kobject deletion during error flow
IB/core: Remove unneeded kobject_get/put calls
IB/core: Fix sparse warnings about redeclared functions
IB/mad: Fix sparse warning about gfp_t use
IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO
IB: Add a QP creation flag to use GFP_NOIO allocations
IB: Return error for unsupported QP creation flags
IB: Allow build of hw/ and ulp/ subdirectories independently
mlx4_core: Move handling of MLX4_QP_ST_MLX to proper switch statement
RDMA/cxgb4: Add missing padding at end of struct c4iw_create_cq_resp
IB/srp: Avoid problems if a header uses pr_fmt
IB/umad: Fix error handling
...
|
|
mlx4_ib_modify_port is invoked in IB for resetting the Q_Key violations
counters and for modifying the IB port capability flags.
For example, when opensm is started up on the hypervisor,
mlx4_ib_modify_port is called to set the port's IsSM flag.
In multifunction mode, the SET_PORT command used in this flow should
be wrapped (so that the PF port capability flags are also tracked,
thus enabling the aggregate of all the VF/PF capability flags to be
tracked properly).
The procedure mlx4_SET_PORT() in main.c is also renamed to mlx4_ib_SET_PORT()
to differentiate it from procedure mlx4_SET_PORT() in port.c.
mlx4_ib_SET_PORT() is used exclusively by mlx4_ib_modify_port().
Finally, the CM invokes ib_modify_port() to set the IsCMSupported flag
even when running over RoCE. Therefore, when RoCE is active,
mlx4_ib_modify_port should return OK unconditionally (since the
capability flags and qkey violations counter are not relevant).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When we receive a netdev event indicating a netdev change and/or
a netdev address change, we must change the MAC index used by the
proxy QP1 (in the QP context), otherwise RoCE CM packets sent by the
VF will not carry the same source MAC address as the non-CM packets.
We use the UPDATE_QP command to perform this change.
In order to avoid modifying a QP context based on netdev event,
while the driver attempts to destroy this QP (e.g either the mlx4_ib
or ib_mad modules are unloaded), we use mutex locking in both flows.
Since the relevant mlx4 proxy GSI QP is created indirectly by the
mad module when they create their GSI QP, the mlx4 didn't need to
keep track on that QP prior to this change.
Now, when QP modifications are needed to this QP from within the
driver, we added refernece to it.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.15:
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will
be arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath
and ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc.
from intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (102 commits)
RDMA/ocrdma: Unregister inet notifier when unloading ocrdma
RDMA/ocrdma: Fix warnings about pointer <-> integer casts
RDMA/ocrdma: Code clean-up
RDMA/ocrdma: Display FW version
RDMA/ocrdma: Query controller information
RDMA/ocrdma: Support non-embedded mailbox commands
RDMA/ocrdma: Handle CQ overrun error
RDMA/ocrdma: Display proper value for max_mw
RDMA/ocrdma: Use non-zero tag in SRQ posting
RDMA/ocrdma: Memory leak fix in ocrdma_dereg_mr()
RDMA/ocrdma: Increment abi version count
RDMA/ocrdma: Update version string
be2net: Add abi version between be2net and ocrdma
RDMA/ocrdma: ABI versioning between ocrdma and be2net
RDMA/ocrdma: Allow DPP QP creation
RDMA/ocrdma: Read ASIC_ID register to select asic_gen
RDMA/ocrdma: SQ and RQ doorbell offset clean up
RDMA/ocrdma: EQ full catastrophe avoidance
RDMA/cxgb4: Disable DSGL use by default
RDMA/cxgb4: rx_data() needs to hold the ep mutex
...
|
|
My static checker complains that the sprintf() here can overflow.
drivers/infiniband/hw/mlx4/main.c:1836 mlx4_ib_alloc_eqs()
error: format string overflow. buf_size: 32 length: 69
This seems like a valid complaint. The "dev->pdev->bus->name" string
can be 48 characters long. I just made the buffer 80 characters instead
of 69 and I changed the sprintf() to snprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The code was indented too far and also kernel style says we should have
curly braces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some code in the mlx4 IB driver stack assumed MLX4_MAX_PORTS ports.
Instead, we should only loop until the number of actual ports in i
the device, which is stored in dev->caps.num_ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To activate RoCE/SRIOV, need to remove the following:
1. In mlx4_ib_add, need to remove the error return preventing
initialization of a RoCE port under SRIOV.
2. In update_vport_qp_params (in resource_tracker.c) need to remove
the error return when a RoCE RC or UD qp is detected.
This error return causes the INIT-to-RTR qp transition to fail
in the wrapper function under RoCE/SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bump all Mellanox driver versions.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'ocrdma', 'qib' and 'usnic' into for-next
|
|
For userspace RoCE UD QPs we need to know the GID format that the
kernel uses, e.g when working over older kernels. For that end, add a
new port capability IB_PORT_IP_BASED_GIDS and report it when query
port is issued.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When scanning netdevices we need to check a few more conditions and
cases to build the IBoE GID table properly. For example, under
bonding we must make sure that when a port is down, the bond IP
address isn't programmed as a GID, since doing so will cause failure
with IB core flows that selects ports by GID.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The IBoE code used to reset the GID table did it for all Ethernet
ports of the device. Since the whole architecture of generating GIDs
and responding to events is port-based, this is inefficient and can
lead to wrong content in the GID table. Change the reset flow to be
per-port.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Updating the GID table under IBoE requires read/write from/to shared
data structures. These data structures are protected with the device
iboe lock. The flows that modify the GID table start from
1. Initializing the GID table
2. NETDEV events
3. INET or INET6 events
This patch makes sure that the flow of initializing the GID table is
consistent with the other two flows w.r.t on what step the lock is taken.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
On the one hand, the invocation of netdev_master_upper_dev_get()
within mlx4_ib_scan_netdevs() must be done with rtnl lock held. On
the other hand, it's wrong to call rtnl_lock() from within this
function since it's also called by our netdev notifier callback.
Therefore move the locking to mlx4_ib_add() so that both cases are
covered.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Make sure that for Ethernet ports, the port GID table index 0 is always
occupied with a default GID of the relevant IPv6 link-local adderss.
This provides better user experience for legacy applications that don't use
the RDMA CM and were working on index 0 prior to the IP addressing change.
Also, as GIDs are generated from IP addresses of the network devices that
are associated with the port, it's basically possible that the GID table
will be empty if no IP address was assigned. This doesn't comply with the
IB spec section 4.1.1 "GID usage and properties".
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When the device has only Ethernet ports, don't try to allocate range
of steerable UD QPs since they aren't needed. This fixes an issue
where mlx4 VFs tried to allocate a range of UD steerable QPs, but
failed to do so.
Fixes: c1c98501121e ("IB/mlx4: Add support for steerable IB UD QPs")
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Conflicts:
drivers/infiniband/hw/mlx4/main.c
|
|
...instead of testing defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE)
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Currently, the mlx4 driver set IBoE (RoCE) gids to encode related
Ethernet netdevice interface MAC address and possibly VLAN id.
Change this scheme such that gids encode interface IP addresses (both
IP4 and IPv6).
This requires learning the IP addresses which are of use by a
netdevice associated with the HCA port, formatting them to gids and
adding them to the port gid table. Furthermore, events of add and
delete address are caught to maintain the gid table accordingly.
Associated IP addresses may belong to a master of an Ethernet
netdevice on top of that port so this should be considered when
building and maintaining the gid table.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This patch adds support for steerable (NETIF) QP creation. When we
create the device, we allocate a range of steerable QPs.
Afterward when a QP is created with the NETIF flag, it's allocated
from this range. Allocation is managed by bitmap allocator.
Internal steering rules for those QPs is automatically generated on
their creation.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The mlx4 device requires adding IB flow spec to rules that apply over
infiniband link layer. This patch adds a mechanism to add such a rule.
If higher levels e.g. IP/UDP/TCP flow specs are provided, the device
requires us to add an empty wild-carded IB rule. Furthermore, the device
requires the QPN to be put in the rule.
Add here specific parsing support for IB empty rules and the ability
to self-generate missing specs based on existing ones.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Up until now, flow steering wasn't supported when using IB ports.
This patch enables support for flow steering if all hardware ports
support that, for example the new MLX4_DEV_CAP_FLAG2_DMFS_IPOIB mlx4
device capability.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
IB/core: Re-enable create_flow/destroy_flow uverbs
IB/core: extended command: an improved infrastructure for uverbs commands
IB/core: Remove ib_uverbs_flow_spec structure from userspace
IB/core: Use a common header for uverbs flow_specs
IB/core: Make uverbs flow structure use names like verbs ones
IB/core: Rename 'flow' structs to match other uverbs structs
IB/core: clarify overflow/underflow checks on ib_create/destroy_flow
IB/ucma: Convert use of typedef ctl_table to struct ctl_table
IB/cm: Convert to using idr_alloc_cyclic()
IB/mlx5: Fix page shift in create CQ for userspace
IB/mlx4: Fix device max capabilities check
IB/mlx5: Fix list_del of empty list
IB/mlx5: Remove dead code
IB/core: Encorce MR access rights rules on kernel consumers
IB/mlx4: Fix endless loop in resize CQ
RDMA/cma: Remove unused argument and minor dead code
RDMA/ucma: Discard events for IDs not yet claimed by user space
IB/core: Add Cisco usNIC rdma node and transport types
RDMA/nes: Remove self-assignment from nes_query_qp()
IB/srp: Report receive errors correctly
...
|
|
This commit reverts commit 7afbddfae993 ("IB/core: Temporarily disable
create_flow/destroy_flow uverbs"). Since the uverbs extensions
functionality was experimental for v3.12, this patch re-enables the
support for them and flow-steering for v3.13.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit 400dbc96583f ("IB/core: Infrastructure for extensible uverbs
commands") added an infrastructure for extensible uverbs commands
while later commit 436f2ad05a0b ("IB/core: Export ib_create/destroy_flow
through uverbs") exported ib_create_flow()/ib_destroy_flow() functions
using this new infrastructure.
According to the commit 400dbc96583f, the purpose of this
infrastructure is to support passing around provider (eg. hardware)
specific buffers when userspace issue commands to the kernel, so that
it would be possible to extend uverbs (eg. core) buffers independently
from the provider buffers.
But the new kernel command function prototypes were not modified to
take advantage of this extension. This issue was exposed by Roland
Dreier in a previous review[1].
So the following patch is an attempt to a revised extensible command
infrastructure.
This improved extensible command infrastructure distinguish between
core (eg. legacy)'s command/response buffers from provider
(eg. hardware)'s command/response buffers: each extended command
implementing function is given a struct ib_udata to hold core
(eg. uverbs) input and output buffers, and another struct ib_udata to
hold the hw (eg. provider) input and output buffers.
Having those buffers identified separately make it easier to increase
one buffer to support extension without having to add some code to
guess the exact size of each command/response parts: This should make
the extended functions more reliable.
Additionally, instead of relying on command identifier being greater
than IB_USER_VERBS_CMD_THRESHOLD, the proposed infrastructure rely on
unused bits in command field: on the 32 bits provided by command
field, only 6 bits are really needed to encode the identifier of
commands currently supported by the kernel. (Even using only 6 bits
leaves room for about 23 new commands).
So this patch makes use of some high order bits in command field to
store flags, leaving enough room for more command identifiers than one
will ever need (eg. 256).
The new flags are used to specify if the command should be processed
as an extended one or a legacy one. While designing the new command
format, care was taken to make usage of flags itself extensible.
Using high order bits of the commands field ensure that newer
libibverbs on older kernel will properly fail when trying to call
extended commands. On the other hand, older libibverbs on newer kernel
will never be able to issue calls to extended commands.
The extended command header includes the optional response pointer so
that output buffer length and output buffer pointer are located
together in the command, allowing proper parameters checking. This
should make implementing functions easier and safer.
Additionally the extended header ensure 64bits alignment, while making
all sizes multiple of 8 bytes, extending the maximum buffer size:
legacy extended
Maximum command buffer: 256KBytes 1024KBytes (512KBytes + 512KBytes)
Maximum response buffer: 256KBytes 1024KBytes (512KBytes + 512KBytes)
For the purpose of doing proper buffer size accounting, the headers
size are no more taken in account in "in_words".
One of the odds of the current extensible infrastructure, reading
twice the "legacy" command header, is fixed by removing the "legacy"
command header from the extended command header: they are processed as
two different parts of the command: memory is read once and
information are not duplicated: it's making clear that's an extended
command scheme and not a different command scheme.
The proposed scheme will format input (command) and output (response)
buffers this way:
- command:
legacy header +
extended header +
command data (core + hw):
+----------------------------------------+
| flags | 00 00 | command |
| in_words | out_words |
+----------------------------------------+
| response |
| response |
| provider_in_words | provider_out_words |
| padding |
+----------------------------------------+
| |
. <uverbs input> .
. (in_words * 8) .
| |
+----------------------------------------+
| |
. <provider input> .
. (provider_in_words * 8) .
| |
+----------------------------------------+
- response, if present:
+----------------------------------------+
| |
. <uverbs output space> .
. (out_words * 8) .
| |
+----------------------------------------+
| |
. <provider output space> .
. (provider_out_words * 8) .
| |
+----------------------------------------+
The overall design is to ensure that the extensible infrastructure is
itself extensible while begin more reliable with more input and bound
checking.
Note:
The unused field in the extended header would be perfect candidate to
hold the command "comp_mask" (eg. bit field used to handle
compatibility). This was suggested by Roland Dreier in a previous
review[2]. But "comp_mask" field is likely to be present in the uverb
input and/or provider input, likewise for the response, as noted by
Matan Barak[3], so it doesn't make sense to put "comp_mask" in the
header.
[1]:
http://marc.info/?i=CAL1RGDWxmM17W2o_era24A-TTDeKyoL6u3NRu_=t_dhV_ZA9MA@mail.gmail.com
[2]:
http://marc.info/?i=CAL1RGDXJtrc849M6_XNZT5xO1+ybKtLWGq6yg6LhoSsKpsmkYA@mail.gmail.com
[3]:
http://marc.info/?i=525C1149.6000701@mellanox.com
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
[ Convert "ret ? ret : 0" to the equivalent "ret". - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
To guarantee that all unused fields in all FW commands for both inboxes
and outboxes are zeroed out, initialize the mailbox buffer to all zeroes.
This is especially important for SRIOV comm-channel virtual commands
(such as QUERY_FUNC_CAP), where if new fields are added to support new
features, the driver can depend on older kernels passing zeroes in these
fields.
In addition to zeroing out the mailbox buffer at allocation time, all
(now unnecessary) calls to memset by the callers of
mlx4_alloc_cmd_mailbox() are removed.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is step #1 for implementing SRIOV resource quotas for VFs.
Quotas are implemented per resource type for VFs and the PF, to prevent
any entity from simply grabbing all the resources for itself and leaving
the other entities unable to obtain such resources.
Resources which are allocated using quotas: QPs, CQs, SRQs, MPTs, MTTs, MAC,
VLAN, and Counters.
The quota system works as follows:
Each entity (VF or PF) is given a max number of a given resource (its quota),
and a guaranteed minimum number for each resource (starvation prevention).
For QPs, CQs, SRQs, MPTs and MTTs:
50% of the available quantity for the resource is divided equally among
the PF and all the active VFs (i.e., the number of VFs in the mlx4_core module
parameter "num_vfs"). This 50% represents the "guaranteed minimum" pool.
The other 50% is the "free pool", allocated on a first-come-first-serve basis.
For each VF/PF, resources are first allocated from its "guaranteed-minimum"
pool. When that pool is exhausted, the driver attempts to allocate from
the resource "free-pool".
The quota (i.e., max) for the VFs and the PF is:
The free-pool amount (50% of the real max) + the guaranteed minimum
For MACs:
Guarantee 2 MACs per VF/PF per port. As a result, since we have only
128 MACs per port, reduce the allowable number of VFs from 64 to 63.
Any remaining MACs are put into a free pool.
For VLANs:
For the PF, the per-port quota is 128 and guarantee is 64
(to allow the PF to register at least a VLAN per VF in VST mode).
For the VFs, the per-port quota is 64 and the guarantee is 0.
We assume that VGT VFs are trusted not to abuse the VLAN resource.
For Counters:
For all functions (PF and VFs), the quota is 128 and the guarantee is 0.
In this patch, we define the needed structures, which are added to the
resource-tracker struct. In addition, we do initialization
for the resource quota, and adjust the query_device response to use quotas
rather than resource maxima.
As part of the implementation, we introduce a new field in
mlx4_dev: quotas. This field holds the resource quotas used
to report maxima to the upper layers (ib_core, via query_device).
The HCA maxima of these values are passed to the VFs (via
QUERY_HCA) so that they may continue to use these in handling
QPs, CQs, SRQs and MPTs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The create_flow/destroy_flow uverbs and the associated extensions to
the user-kernel verbs ABI are under review and are too experimental to
freeze at this point.
So userspace is not exposed to experimental features and an uinstable
ABI, temporarily disable this for v3.12 (with a Kconfig option behind
staging to reenable it if desired).
The feature will be enabled after proper cleanup for v3.13.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1381351016.git.ydroneaud@opteya.com
Link: http://marc.info/?i=cover.1381177342.git.ydroneaud@opteya.com
[ Add a Kconfig option to reenable these verbs. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
