| Age | Commit message (Collapse) | Author |
|---|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517164645.162294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Probe the touch controller driver even if resolution information is not
available. This can happen e.g. in case the touch controller suffered a
failed firmware update and is stuck in bootloader mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230217025200.203833-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The touch controller needs some time to wake-up after setting the wake-up
gpio. Without having a delay after wake-up probing regularly fails in
edt_ft5x06_ts_identify() with an error (i.e. EREMOTEIO) that was caused
by a failed i2c transfer.
The datasheet sets the wake-up time to 5 ms, although it is not entirely
clear.
Signed-off-by: Philipp Puschmann <p.puschmann@pironex.com>
Link: https://lore.kernel.org/r/20230505115823.545803-1-p.puschmann@pironex.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The touchscreen can be put into a deep sleep state that prevents it from
emitting touch irqs. Put the touchscreen into deep sleep during suspend
if it is not marked as a wakeup source.
This also fixes a problem with the touchscreen getting unresponsive after
system resume when a falling edge trigger is used for the interrupt.
When left on during suspend, the touchscreen would pull the interrupt
line down in response to touch events, leaving the interrupt effectively
disabled after resume.
Signed-off-by: Maximilian Weigand <mweigand@mweigand.net>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20230504120316.408687-2-mweigand2017@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add support for touch keys found in some Atmel touch controller
configurations.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Link: https://lore.kernel.org/r/20230407-atmel_keys-v2-2-92446a4343cb@apitzsch.eu
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The watchdog_timer can schedule tx_timeout_task and watchdog_work
can also arm watchdog_timer. The process is shown below:
----------- timer schedules work ------------
cyttsp4_watchdog_timer() //timer handler
schedule_work(&cd->watchdog_work)
----------- work arms timer ------------
cyttsp4_watchdog_work() //workqueue callback function
cyttsp4_start_wd_timer()
mod_timer(&cd->watchdog_timer, ...)
Although del_timer_sync() and cancel_work_sync() are called in
cyttsp4_remove(), the timer and workqueue could still be rearmed.
As a result, the possible use after free bugs could happen. The
process is shown below:
(cleanup routine) | (timer and workqueue routine)
cyttsp4_remove() | cyttsp4_watchdog_timer() //timer
cyttsp4_stop_wd_timer() | schedule_work()
del_timer_sync() |
| cyttsp4_watchdog_work() //worker
| cyttsp4_start_wd_timer()
| mod_timer()
cancel_work_sync() |
| cyttsp4_watchdog_timer() //timer
| schedule_work()
del_timer_sync() |
kfree(cd) //FREE |
| cyttsp4_watchdog_work() // reschedule!
| cd-> //USE
This patch changes del_timer_sync() to timer_shutdown_sync(),
which could prevent rearming of the timer from the workqueue.
Fixes: 17fb1563d69b ("Input: cyttsp4 - add core driver for Cypress TMA4XX touchscreen devices")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20230421082919.8471-1-duoming@zju.edu.cn
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The removed lines are remnants of the vendor driver and are not used in
the upstream driver.
Signed-off-by: Maximilian Weigand <mweigand@mweigand.net>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20230501113010.891786-3-mweigand@mweigand.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
rpi_firmware_get() take reference, we need to release it in error paths
as well. Use devm_rpi_firmware_get() helper to handling the resources.
Also remove the existing rpi_firmware_put().
Fixes: 0b9f28fed3f7 ("Input: add official Raspberry Pi's touchscreen driver")
Fixes: 3b8ddff780b7 ("input: raspberrypi-ts: Release firmware handle when not needed")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20221223074657.810346-1-linmq006@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
After starting to use regmap API to access registers the edt-ft5x06
driver depends on symbols provided by REGMAP_I2C:
edt-ft5x06.o: in function `edt_ft5x06_ts_probe':
edt-ft5x06.c:1154: undefined reference to `__regmap_init_i2c'
edt-ft5x06.o: in function `edt_ft5x06_ts_identify':
edt-ft5x06.c:897: undefined reference to `__regmap_init_i2c'
Make sure support for I2C regmap is actually selected by adding this
dependency to Kconfig.
Fixes: 9dfd9708ffba ("Input: edt-ft5x06 - convert to use regmap API")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZDRBExF1xmxalMZc@makrotopia.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver had the code to differentiate between finger and palm touches,
but did not use this information when reporting contacts. Change it so that
proper "tool" type is assigned to reported contacts.
Signed-off-by: JungHoon Hyun <hyunjunghoon@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
It is pointless and expensive to calculate data in the interrupt that
depends on the type of touchscreen, which is detected on the driver
probe and cannot then be changed.
So calculate the size of the data buffer on the driver probe, as well as
the data retrieval command, and then use them in the ISR.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230402200951.1032513-10-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
With this patch, the CRC is always verified by the same function, even in
the case of accessing registers where the number of bytes is minimal.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230402200951.1032513-9-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
It replaces custom read/write functions with regmap API, making the
driver code more generic.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230402200951.1032513-8-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In some parts of the code, error messages were improperly printed with
dev_dbg() calls. In those cases, dev_dbg() has been replaced with
dev_err().
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230402200951.1032513-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The use of the macros M06_REG_ADDR and M06_REG_CMD avoids code
duplication without impacting the application load, and reduces the
chances of errors or mistakes.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230402200951.1032513-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
There is no need to recalculate the CRC when the data has not changed.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230402200951.1032513-5-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
It adds spaces around '-' as recommended by the Linux coding style.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230402200951.1032513-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
It removes unnecessary blank lines so that checkpatch doesn't complain
anymore.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230402200951.1032513-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Matches the alignment to the open parenthesis as suggested by
checkpatch.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230402200951.1032513-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When a hard IRQ is triggered, the soft IRQ, which decides if an actual
pen down happened, should always be triggered. This enables the usage of
"can_sleep" GPIO chips as "pen down" GPIO, as the value is not read
during the hard IRQ anymore. This might be the case if the GPIO chip is
an expander behind i2c.
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20230328-tsc2007-sleep-v5-1-fc55e76d0ced@skidata.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add a new driver for the Novatek i2c touchscreen controller as found
on the Acer Iconia One 7 B1-750 tablet. Unfortunately the touchscreen
controller model-number is unknown. Even with the tablet opened up it
is impossible to read the model-number.
Android calls this a "NVT-ts" touchscreen, but that may apply to other
Novatek controller models too.
This appears to be the same controller as the one supported by
https://github.com/advx9600/android/blob/master/touchscreen/NVTtouch_Android4.0/NVTtouch.c
but unfortunately that does not give us a model-number either.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20230326212308.55730-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312131514.351603-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/input/touchscreen/sun4i-ts.c:392:34: error: ‘sun4i_ts_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230312131514.351603-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144708.1542682-1-robh@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merge with mainline to get of_property_present() and other newer APIs.
|
|
The HiDeep IST940E touchscreen controller used on the Lenovo Yoga Book X90F
convertible comes up in HID mode by default.
This works well on the X91F Windows model where the touchscreen is
correctly described in ACPI and ACPI takes care of controlling
the reset GPIO and regulators.
But the X90F ships with Android and the ACPI tables on this model don't
describe the touchscreen. Instead this is hardcoded in the vendor kernel.
The vendor kernel uses the touchscreen in native HiDeep 20 (2.0?) protocol
mode and switches the controller to this mode by writing 0 to reg 0x081e.
Adjusting the i2c-hid code to deal with the reset-gpio and regulators on
this non devicetree (but rather broken ACPI) convertible is somewhat tricky
and the native protocol reports ABS_MT_PRESSURE and ABS_MT_TOUCH_MAJOR
which are not reported in HID mode, so it is preferable to use the native
mode.
Add support to the hideep driver to reset the work-mode to the native
HiDeep protocol to allow using it on the Lenovo Yoga Book X90F.
This is guarded behind a new "hideep,force-native-protocol" boolean
property, to avoid changing behavior on other devices.
For the record: I did test using the i2c-hid driver with some quick hacks
and it does work. The I2C-HID descriptor is available from address 0x0020,
just like on the X91F Windows model.
So far the new "hideep,force-native-protocol" property is only used on
x86/ACPI (non devicetree) devs. IOW it is not used in actual devicetree
files. The devicetree-bindings maintainers have requested properties like
these to not be added to the devicetree-bindings, so the new property is
deliberately not added to the existing devicetree-bindings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230311114726.182789-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
On some models the first HIDEEP_SYSCON_WDT_CON write alone is enough to
cause the controller to reset, causing the second write to fail:
i2c-hideep_ts: write to register 0x52000014 (0x000001) failed: -121
Switch this write to a raw hideep_pgm_w_mem() to avoid an error getting
logged in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230311114726.182789-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Turn the space into a tab to Eliminate the follow smatch warning:
drivers/input/touchscreen/hideep.c:470 hideep_program_nvm() warn:
inconsistent indenting
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220429070103.4747-1-yang.lee@linux.alibaba.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a set of tweaks to iqs269a touch controller driver
- a fix for ads7846 driver to properly handle 7845 chip
- cap11xx driver will support cap1203, cap1293 and cap1298 models
- xpad driver will support 8BitDo Pro 2 Wired Controller
- input drivers have been switched to DEFINE_SIMPLE_DEV_PM_OPS() and
pm_sleep_ptr()
- other miscellaneous fixes and tweaks
* tag 'input-for-v6.3-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (113 commits)
dt-bindings: input: iqs626a: Redefine trackpad property types
Input: iqs626a - drop unused device node references
dt-bindings: input: touchscreen: st,stmfts: convert to dtschema
Input: cyttsp5 - fix bitmask for touch buttons
Input: exc3000 - properly stop timer on shutdown
Input: synaptics-rmi4 - fix SPI device ID
Input: cap11xx - add support for cap1203, cap1293 and cap1298
dt-bindings: input: microchip,cap11xx: add cap1203, cap1293 and cap1298
Input: pmic8xxx-keypad - fix a Kconfig spelling mistake & hyphenation
Input: edt-ft5x06 - fix typo in a comment
Input: tegra-kbc - use devm_platform_get_and_ioremap_resource()
Input: st-keyscan - use devm_platform_get_and_ioremap_resource()
Input: spear-keyboard - use devm_platform_get_and_ioremap_resource()
Input: olpc_apsp - use devm_platform_get_and_ioremap_resource()
Input: arc_ps2 - use devm_platform_get_and_ioremap_resource()
Input: apbps2 - use devm_platform_get_and_ioremap_resource()
Input: altera_ps2 - use devm_platform_get_and_ioremap_resource()
Input: ads7846 - don't check penirq immediately for 7845
Input: ads7846 - always set last command to PWRDOWN
Input: ads7846 - don't report pressure for ads7845
...
|
|
Prior to this patch, the bitmask ends up being 0x3, as opposed to 0x1
which likely was the intention. The erroneous bit results in the driver
reporting 2 different button activations in designs with 2 or more
buttons.
To detect which button has been pressed, cyttsp5_btn_attention() uses a
for loop to iterate through the input buffer, while shifting and
applying a bitmask to determine the state for each button.
Unfortunately, when the bitmask is 0x3 and there are multiple buttons,
this procedure falls apart.
Consider a design with 3 buttons. Pressing the third button will result
in a call to cyttsp5_btn_attention() with the input buffer containing
0x4 (binary 0100). In the first iteration of the for loop cur_btn_state
will be:
(0x4 >> 0 * 1) & 0x3 = 0x4 & 0x3 = 0x0
This is correct. However, in the next iteration this happens:
(0x4 >> 1 * 1) & 0x3 = 0x2 & 0x3 = 0x2
Which means that a key event for key 1 is generated, even though it's
not really active. In the third iteration, the loop detects the button
that was actually pressed:
(0x4 >> 2 * 1) & 0x3 = 0x1 & 0x3 = 0x1
This key event is the only one that should have been detected, but it is
accompanied by the preceding key. Ensuring the applied mask is 0x1
solves this problem.
Signed-off-by: Richard Kjerstadius <richard.kjerstadius@teledyne.com>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20230127102903.3317089-1-richard.kjerstadius@teledyne.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We need to stop the timer on driver unbind or probe failures, otherwise
we get UAF/Oops.
Fixes: 7e577a17f2ee ("Input: add I2C attached EETI EXC3000 multi touch driver")
Reported-by: "Stahl, Michael" <mstahl@moba.de>
Link: https://lore.kernel.org/r/Y9dK57BFqtlf8NmN@google.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ucb1400 MFD driver and its gpio and touchscreen child
drivers were only used on a few PXA machines that were unused
for a while and are now removed.
Removing these leaves the AC97 support as ALSA specific,
no other drivers are now connected through this interface.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Lee Jones <lee@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The PXA zylonite platform was removed, so this driver has no
remaining users.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-input@vger.kernel.org
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Replace 'firmares' with 'firmwares'.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230128162325.64467-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
To discard false readings, one should use "ti,penirq-recheck-delay-usecs".
Checking get_pendown_state() at the beginning, most of the time fails
causing malfunctioning.
Fixes: ffa458c1bd9b ("spi: ads7846 driver")
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230126105227.47648-4-l.ellero@asem.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Controllers that report pressure (e.g. ADS7846) use 5 commands and the
correct sequence is READ_X, READ_Y, READ_Z1, READ_Z2, PWRDOWN.
Controllers that don't report pressure (e.g. ADS7845/ADS7843) use only 3
commands and the correct sequence should be READ_X, READ_Y, PWRDOWN. But
the sequence sent was incorrect: READ_X, READ_Y, READ_Z1.
Fix this by setting the third (and last) command to PWRDOWN.
Fixes: ffa458c1bd9b ("spi: ads7846 driver")
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230126105227.47648-3-l.ellero@asem.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
ADS7845 doesn't support pressure.
Avoid the following error reported by libinput-list-devices:
"ADS7845 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE".
Fixes: ffa458c1bd9b ("spi: ads7846 driver")
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230126105227.47648-2-l.ellero@asem.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The previous change was not properly build tested and needs
a trivial spelling change:
ipaq-micro-ts.c:146:8: error: type defaults to 'int' in declaration of 'DEFINE_SIMPLE_DEV_PM' [-Werror=implicit-int]
Fixes: 144ff5e03d74 ("Input: ipaq-micro-ts - use DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230117164539.1631336-1-arnd@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection
against unused function warnings. The new combination of pm_sleep_ptr()
and EXPORT_GPL_SIMPLE_DEV_PMU_OPS() allows the compiler to see the
functions, thus suppressing the warning, but still allowing the unused
code to be removed. Thus also drop the __maybe_unused markings.
It also rolls in the EXPORT_SYMBOL() so that we only export it
if CONFIG_PM_SLEEP.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230114171620.42891-12-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
SET_SYSTEM_SLEEP_PM_OPS() and RUNTIME_PM_OPS() are deprecated as
they requires explicit protection against unused function warnings.
The new combination of pm_ptr() EXPORT_GPL_RUNTIME_DEV_PM_OPS()
allows the compiler to see the functions, thus suppressing the
warning, but still allowing the unused code to be
removed. Thus also drop the #ifdef guards.
Note that we are replacing an unconditional call to the suspend
and resume functions for sleep use cases with one via
pm_runtime_force_suspend() / pm_runtime_force_resume() that only
do anything to the device if we are not already in the appropriate
runtime suspended state.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
--
I 'think' this should be fine in that it can only reduce the number
of unnecessary suspends. If anyone can test that would be great.
Link: https://lore.kernel.org/r/20230114171620.42891-11-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection
against unused function warnings. The new combination of pm_sleep_ptr()
and EXPORT_GPL_SIMPLE_DEV_PM_OPS() allows the compiler to see the
functions, thus suppressing the warning, but still allowing the unused
code to be removed. Thus also drop the __maybe_unused markings.
This function also removes the need for separate EXPORT_SYMBOL_GPL()
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230114171620.42891-10-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() are deprecated as
they require explicit protection against unused function warnings.
The new combination of pm_ptr() and SYSTEM_SLEEP_PM_OPS()/
RUNTIME_PM_OPS() allows the compiler to see the functions,
thus suppressing the warning, but still allowing the unused code to be
removed. Thus also drop the __maybe_unused markings.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20230114171620.42891-7-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() are deprecated as
they require explicit protection against unused function warnings.
The new combination of pm_ptr() and SYSTEM_SLEEP_PM_OPS()/
RUNTIME_PM_OPS() allows the compiler to see the functions,
thus suppressing the warning, but still allowing the unused code to be
removed. Thus also drop the __maybe_unused markings.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Caleb Connolly <caleb@connolly.tech>
Cc: Andi Shyti <andi@etezian.org>
Tested-by: Caleb Connolly <caleb@connolly.tech> # oneplus-guacamole
Link: https://lore.kernel.org/r/20230114171620.42891-5-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The majority of all pxa board files has not been touched in a long time,
and no users have spoken up in favor of keeping them around. This leaves
only support for the platforms that were already converted to DT, as
well as the gumstix and spitz/akita/borzoi machines that work in qemu
and can still be converted to DT later.
Cc: Ales Bardorfer <ales@i-tech.si>
Cc: Ales Snuparek <snuparek@atlas.cz>
Cc: Alex Osborne <ato@meshy.org>
Cc: Alex Osborne <bobofdoom@gmail.com>
Cc: Dirk Opfer <dirk@opfer-online.de>
Cc: Ian Molton <spyro@f2s.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Michael Petchkovsky <mkpetch@internode.on.net>
Cc: Nick Bane <nick@cecomputing.co.uk>
Cc: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Tomas Cech <sleep_walker@suse.cz>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The s3c24xx SoC support and its adc driver was removed, so this driver
has no remaining users.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Merge with mainline to bring in timer_shutdown_sync() API.
|
|
This driver never used the older SIMPLE_DEV_PM_OPS() but instead just
set two of the callbacks directly. Skip that deprecated macro and go
straight to the new form that avoids the need for guarding or marking
callbacks __maybe_unused.
--
It is possible there is some subtle reason why only two of the
callbacks normally set by SIMPLE_DEV_PM_OPS() are set. As such,
this one needs some closer reading than many of the others.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230102181842.718010-70-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection
against unused function warnings. The new combination of pm_sleep_ptr()
and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions,
thus suppressing the warning, but still allowing the unused code to be
removed. Thus also drop the __maybe_unused markings.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230102181842.718010-69-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection
against unused function warnings. The new combination of pm_sleep_ptr()
and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions,
thus suppressing the warning, but still allowing the unused code to be
removed. Thus also drop the __maybe_unused markings.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230102181842.718010-68-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection
against unused function warnings. The new combination of pm_sleep_ptr()
and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions,
thus suppressing the warning, but still allowing the unused code to be
removed. Thus also drop the __maybe_unused markings.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230102181842.718010-67-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
