| Age | Commit message (Collapse) | Author |
|---|
|
Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION
controls to the ov2685 driver by attempting to parse them from firmware.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
If the sensor doens't power up correctly, for example due to incorrect
devicetree description, the power up i2c writes will fail.
Add an error print for this situation.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The imx296 driver uses the subdev active state, there's no need to
implement the .get_fmt() operation manually. Use the
v4l2_subdev_get_fmt() helper instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The ov5670 driver tries to get a reference to the xvclk provider by using
the common cock framework and deflects to parsing the "clock-frequency"
property in case the clock provider is not specified in the firmware
interface, detected by checking if ov5670->xvclk == PTR_ERR(-ENOENT).
However, as reported by the Smatch static checker, if CONFIG_HAVE_CLK is
not enabled, devm_clk_get() returns 0 which when passed to PTR_ERR()
means success causing the driver to fail without propagating any error
code up.
Explicitly handle the case where ov5670->xvclk it set to NULL, forcing
the code to parse the "clock-frequency" property in case CONFIG_HAVE_CLK
is not enabled, as suggested by Dan Carpenter.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Currently the driver always configures the sensor for dual-lane MIPI
output, but it also supports single-lane output. Add support for that by
checking the data-lanes fwnode property how many lanes are used and
configure the necessary registers based on that.
To achieve this we move setting register 0x3018 out of the general reg
sequence so we set it to the correct value. The pixel_rate value also
needs to be adjusted.
[Sakari Ailus: Use div_s64 to divide a 64-bit number]
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Replace the unusual const char *err_msg usage with dev_err_probe which
also handles -EPROBE_DEFER better by not printing the message to kmsg.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Both sensors are quite similar. Their specs only differ regarding LVDS
and parallel output but are identical regarding MIPI-CSI-2 interface.
But they use a different init setting of hard-coded values, taken from
the datasheet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
imx290_start_streaming logs what failed, but not the error
code from that function. Add it into the log message.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The sensor supports H & V flips, so add the relevant hooks for
V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
Note that the Bayer order is maintained as the readout area
shifts by 1 pixel in the appropriate direction (note the
comment about the top margin being 8 pixels whilst the bottom
margin is 9). The V4L2_SEL_TGT_CROP region is therefore
adjusted appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The sensor supports either a 37.125 or 74.25MHz external, but
the driver only supported 37.125MHz.
Add the relevant register configuration for either clock
frequency option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
IMX290_CTRL_07 was written from both imx290_global_init_settings
and imx290_1080p_settings and imx290_720p_settings.
Remove it from imx290_global_init_settings as the setting varies
based on the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The default VMAX for 60fps in 720p mode is 750 according to the
datasheet, however the driver always left it at 1125 thereby stopping
60fps being achieved.
Make VMAX (and therefore V4L2_CID_VBLANK) mode dependent so that 720p60
can be achieved.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The driver exposed V4L2_CID_VBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
V4L2_CID_VBLANK also sets the limits for the exposure control,
therefore exposure ranges have to be updated when vblank changes
(either via s_ctrl, or via changing mode).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The driver exposed V4L2_CID_HBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" added support for the increased link frequencies
on 2 data lanes, but didn't update the CSI timing registers in
accordance with the datasheet.
Use the specified settings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Commit "97589ad61c73 media: i2c: imx290: Add support for 2 data lanes"
added support for running in two lane mode (instead of 4), but
without changing the link frequency that resulted in a max of 30fps.
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" then doubled the link frequency when in 2 lane mode,
but didn't undo the correction for running at only 30fps, just extending
horizontal blanking instead.
Remove the 30fps limit on 2 lane by correcting the register config
in accordance with the datasheet for 60fps operation over 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The datasheet lists the link frequency changes between
1080p and 720p modes. This is correct that the link frequency
changes as measured on an oscilloscope.
Link frequency is not necessarily the same as pixel rate.
The datasheet gives standard configurations for 1080p and 720p
modes at a number of frame rates.
Looking at the 1080p mode it gives:
HMAX = 0x898 = 2200
VMAX = 0x465 = 1125
2200 * 1125 * 60fps = 148.5MPix/s
Looking at the 720p mode it gives:
HMAX = 0xce4 = 3300
VMAX = 0x2ee = 750
3300 * 750 * 60fps = 148.5Mpix/s
This driver currently scales the pixel rate proportionally to the
link frequency, however the above shows that this is not the
correct thing to do, and currently all frame rate and exposure
calculations give incorrect results.
Correctly report the pixel rate as being 148.5MPix/s under any
mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Any V4L2 subdevice that implements controls and declares
V4L2_SUBDEV_FL_HAS_DEVNODE should also declare V4L2_SUBDEV_FL_HAS_EVENTS
and implement subscribe_event and unsubscribe_event hooks.
This driver didn't and would therefore fail v4l2-compliance
testing.
Add the relevant hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The colorspace fields were left untouched in imx290_set_fmt
which lead to a v4l2-compliance failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Fix up a couple of coding style issues regarding missing blank
lines after declarations, double blank lines, and incorrect
indentation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The IMX290 module is available as either mono or colour (Bayer).
Update the driver so that it can advertise the correct mono
formats instead of the colour ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The ov5647_read() functions calls i2c_master_send() and
i2c_master_read() in sequence. However this leaves space for other
clients to contend the bus and insert an unrelated transaction in between
the two calls.
Replace the two calls with a single i2c_transfer() one, that locks the
bus in between the transactions.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
This adds V4L2_CID_TEST_PATTERN control support.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
No need to call fwnode_property_read_u32(dev_fwnode()), when
we have already existing helper. So use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Since we have a proper endianness converters for LE 24-bit data use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
in tx_from_ep
tx_from_ep's for loop uses '5' as bound, while in fact it refers to the
number of polarities. Replace it by VGXY61_NB_POLARITIES for
factorization.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
In case of error 'update_hdr' now goes through 'power_off' instead of
returning, effectively shutting down the sensor.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Previously the device detection was performed after patching.
Move it right after the reset to make sure we have the correct sensor
before trying to patch it.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
At this stage the default mode is unknown.
This is done correctly by vgxy61_fill_framefmt right after.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
./drivers/media/i2c/tc358746.c:857:3-4: Unneeded semicolon
./drivers/media/i2c/tc358746.c:861:2-3: Unneeded semicolon
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2832
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The runtime suspend/resume functions are only referenced from the
dev_pm_ops, but they use the old SET_RUNTIME_PM_OPS() helper
that requires a __maybe_unused annotation to avoid a warning:
drivers/media/i2c/imx290.c:1082:12: error: unused function 'imx290_runtime_resume' [-Werror,-Wunused-function]
static int imx290_runtime_resume(struct device *dev)
^
drivers/media/i2c/imx290.c:1090:12: error: unused function 'imx290_runtime_suspend' [-Werror,-Wunused-function]
static int imx290_runtime_suspend(struct device *dev)
^
Convert this to the new RUNTIME_PM_OPS() helper that so this
is not required. To improve this further, also use the pm_ptr()
helper that lets the dev_pm_ops get dropped entirely when
CONFIG_PM is disabled.
A related mistake happened in the of_match_ptr() macro here, which
like SET_RUNTIME_PM_OPS() requires the match table to be marked
as __maybe_unused, though I could not reproduce building this without
CONFIG_OF. Remove the of_match_ptr() here as there is no point in
dropping the match table in configurations without CONFIG_OF.
Fixes: 02852c01f654 ("media: i2c: imx290: Initialize runtime PM before subdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so
it can be trivially converted.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/lkml/20221121102838.16448-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so
it can be trivially converted.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/lkml/20221121102705.16092-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If the media bus is unsupported, then return -EINVAL. Instead it
returned 'ret' which happened to be 0.
This fixes a smatch warning:
ov7670.c:1843 ov7670_parse_dt() warn: missing error code? 'ret'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 01b8444828fc ("media: v4l2: i2c: ov7670: Implement OF mbus configuration")
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Since 'ret' is known to be 0, just return '0'. This fixes a smatch warning:
s5c73m3-core.c:439 __s5c73m3_s_stream() warn: missing error code? 'ret'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
There are no existing users of s5c73m3_platform_data in the tree, and
new users should either be using device tree, ACPI, or static device
properties, so let's remove it from the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Add driver for the Sony IMX415 CMOS image sensor.
Signed-off-by: Gerald Loacker <gerald.loacker@wolfvision.net>
Co-developed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The ov5670 driver registers three controls as read-only:
- V4L2_CID_PIXEL_RATE
- V4L2_CID_LINK_FREQ
- V4L2_CID_HBLANK
The driver updates the range of HBLANK with __v4l2_ctrl_modify_range()
and updates the values of PIXEL_RATE and LINK_FREQ with an
explicit call to __v4l2_ctrl_s_ctrl() in ov5670_set_pad_format() time.
This causes the .set_ctrl handler to be called on these controls
causing a non-fatal warning to be emitted:
ov5670_set_ctrl Unhandled id:0x9e0902, val:0x824
This is currently only critical for HBLANK, as LINK_FREQ and PIXEL_RATE
currently only support a single value, and the v4l2-ctrl framework skips
calling .set_ctrl() if the current control value is not changed.
Expand the ov5670_set_ctrl() callback to handle the above controls
to remove the above warning and defend against future expansions
of the supported pixel rates and link frequencies.
Also be stricter and return an error value if a control is actually not
handled.
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Add support for the .get_selection() pad operation to the ov5670 sensor
driver.
Report the native sensor size (pixel array), the crop bounds (readable
pixel array area) and the current and default analog crop rectangles.
Currently all driver's modes use an analog crop rectangle of size
[12, 4, 2600, 1952]. Instead of hardcoding the value in the operation
implementation, ad an .analog_crop field to the sensor's modes
definitions, to make sure that if any mode gets added, its crop
rectangle will be defined as well.
While at it re-sort the modes' field definition order to match the
declaration order and initialize the crop rectangle in init_cfg().
[Sakari Ailus: Fix a typo on comments (03800 -> 0x3800)]
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Implement the .init_cfg() pad operation and initialize the default
format with the default full resolution mode 2592x1944.
With .init_cfg() pad operation implemented the deprecated .open()
internal operation can now be dropped.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Implement the runtime resume and suspend routines and install them as
runtime_pm handlers.
While at it rework the probe() sequence in order to enable runtime_pm
before registering the async subdevice.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The OV5670 has a powerdown and reset pin, named respectively "PWDN" and
"XSHUTDOWN".
Optionally probe the gpios connected to the pins during the driver probe
routine.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The OV5670 has three power supplies (AVDD, DOVDD and DVDD).
Probe them in the driver to prepare controlling with runtime_pm
operations.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Add support for probing the main system clock using the common clock
framework and its OF bindings.
Maintain ACPI compatibility by falling back to parse 'clock-frequency'.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The ov5670 driver currently only supports probing using ACPI matching.
Add support for OF and add a missing header inclusion.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The sensor has 2592*1944 active pixels, surrounded by 16 active dummy
pixels and there are an additional 24 black rows "at the bottom".
[2624]
+-----+------------------+-----+
| | 16 dummy | |
+-----+------------------+-----+
| | | |
| | [2592] | |
| | | |
|16 | valid | 16 |[2000]
|dummy| |dummy|
| | [1944]| |
| | | |
+-----+------------------+-----+
| | 16 dummy | |
+-----+------------------+-----+
| | 24 black lines | |
+-----+------------------+-----+
The top-left coordinate is gotten from the registers specified in the
modes which are identical for both currently supported modes.
There are currently two modes supported by this driver: 2592*1944 and
1296*972. The second mode is obtained thanks to subsampling while
keeping the same field of view (FoV). No cropping involved, hence the
harcoded values.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Parse V4L2 device tree properties and register controls for them.
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Until now, this driver only supported ACPI. This adds support for
Device Tree too while enabling clock and regulators in runtime PM.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
2x2 binning works fine for RAW10 capture, but for RAW8 1232p mode it
leads to corrupted frames [1][2].
Using the special 2x2 analog binning mode fixes the issue, but causes
artefacts for RAW10 1232p capture. So here we choose the binning mode
depending upon the frame format selected.
As both binning modes work fine for 480p RAW8 and RAW10 capture, it can
share the same code path as 1232p for selecting binning mode.
[1] https://forums.raspberrypi.com/viewtopic.php?t=332103
[2] https://github.com/raspberrypi/libcamera-apps/issues/281
Fixes: 22da1d56e982 ("media: i2c: imx219: Add support for RAW8 bit bayer format")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The IMX296LLR is a monochrome 1.60MP CMOS sensor from Sony. The driver
supports cropping and binning (but not both at the same time due to
hardware limitations) and exposure, gain, vertical blanking and test
pattern controls.
Preliminary support is also included for the color IMX296LQR sensor.
[Sakari Ailus: Make driver's remove function return void]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
