| Age | Commit message (Collapse) | Author |
|---|
|
With the TMIO MFD support gone, the corresponding MMC host driver can
be removed as well. The remaining tmio_mmc_core module however is still
used by both the Renesas and Socionext host drivers.
Cc: Ian Molton <spyro@f2s.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The uevent() callback in struct bus_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-16-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SD interface logic has the register to switch UHS speed.
The default is up to SDR25 and to support SDR50 or faster,
add uniphier_sd_speed_switch() function to switch the speed mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20230125010201.28246-4-hayashi.kunihiko@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Transition of UHS mode needs to control the register in SD interface
logic. Add access to the register in the logic using the regmap from
"socionext,syscon-uhs-mode" property.
Define the start_signal_voltage_switch function only if UHS mode is
available.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20230125010201.28246-3-hayashi.kunihiko@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This commit fixes a race between completion of stop command and start of a
new command.
Previously the command ready interrupt was enabled before stop command
was written to the command register. This caused the command ready
interrupt to fire immediately since the CMDRDY flag is asserted constantly
while there is no command in progress.
Consequently the command state machine will immediately advance to the
next state when the tasklet function is executed again, no matter
actual completion state of the stop command.
Thus a new command can then be dispatched immediately, interrupting and
corrupting the stop command on the CMD line.
Fix that by dropping the command ready interrupt enable before calling
atmci_send_stop_cmd. atmci_send_stop_cmd does already enable the
command ready interrupt, no further writes to ATMCI_IER are necessary.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20221230194315.809903-2-t.schramm@manjaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The PXA168 errata recommends that the CMD signal should be detached from
the SD bus while performing the dummy CMD0 to restart the clock.
Implement this using pinctrl states.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230116194401.20372-8-doug@schmorgal.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The PXA168 has a documented silicon bug that causes SDIO card IRQs to be
missed. Implement the first half of the suggested workaround, which
involves resetting the data port logic and issuing a dummy CMD0 to
restart the clock.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230116194401.20372-7-doug@schmorgal.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add ability to have an optional core clock just like the pxav3 driver.
The PXA168 needs this because its SDHC controllers have separate core
and io clocks that both need to be enabled. This also correctly matches
the documented devicetree bindings for this driver.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230116194401.20372-6-doug@schmorgal.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The devicetree bindings for this driver specify that the two allowed
clock names are io and core. Change this driver to look for io, but
allow any name if it fails for backwards compatibility. Follow the same
pattern used in sdhci-pxav3, but add support for EPROBE_DEFER.
Get rid of an unnecessary pdev->dev while we're at it.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230116194401.20372-5-doug@schmorgal.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The PXA168 has a documented silicon bug that results in a data abort
exception when accessing the SDHCI_HOST_VERSION register on SDH2 and
SDH4 through a 16-bit read. Implement the workaround described in the
errata, which performs a 32-bit read from a lower address instead. This
is safe to use on all four SDH peripherals.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230116194401.20372-4-doug@schmorgal.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Enable CONFIG_MMC_SDHCI_IO_ACCESSORS for the pxav2 driver. The read_w
callback is needed for a silicon bug workaround in the PXA168.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230116194401.20372-3-doug@schmorgal.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add a new compatible string for the version 1 controller used in the
PXA168, along with necessary quirks. Use a separate ops struct in
preparation for a silicon bug workaround only necessary on V1.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230116194401.20372-2-doug@schmorgal.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
pwrseq_sd8787 is forced to be built as a module if its dependencies are.
That's unnecessary, it's perfectly fine for it to be built-in even
though the wireless drivers that need it are modules.
Relax the depends definition in Kconfig accordingly.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matt Ranostay <matt@ranostay.consulting>
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/8bb3d7c3a36985e030ba40e853c57578de8fb303.1673866725.git.lukas@wunner.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This commit enables SDHCI Host V4 support on Bluefield-3 SoC to be
consistent with the default setting in firmware(UEFI).
Reviewed-by: David Woods <davwoods@nvidia.com>
Signed-off-by: Liming Sun <limings@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/990885f566c32ac8e6888ad6b434fb70d1a5d7af.1673460632.git.limings@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Now that it is no longer used, remove SDHCI_QUIRK_MISSING_CAPS.
Note, from now on, __sdhci_read_caps() should be used to provide missing
capability flags.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230113110011.129835-7-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SDHCI_QUIRK_MISSING_CAPS is not needed because __sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with __sdhci_read_caps().
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20230113110011.129835-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SDHCI_QUIRK_MISSING_CAPS is not needed because sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with sdhci_read_caps().
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20230113110011.129835-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SDHCI_QUIRK_MISSING_CAPS is not needed because sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with sdhci_read_caps().
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20230113110011.129835-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SDHCI_QUIRK_MISSING_CAPS is not needed because sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with sdhci_read_caps().
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230113110011.129835-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SDHCI_QUIRK_MISSING_CAPS is not needed because __sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with __sdhci_read_caps() for Ricoh SDHCI
controller.
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230113110011.129835-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix a misspelling of "complement".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/a650c8b930a30f5902f4fcfe23877314d098abde.1672763862.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This adds a reason to /sys/kernel/debug/devices_deferred, which makes
it easier to debug deferred probes such as [0].
0. https://lore.kernel.org/all/20221228140708.26431-1-tom@tom-fitzhenry.me.uk/
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Link: https://lore.kernel.org/r/20221228142354.28454-1-tom@tom-fitzhenry.me.uk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
device
USDHC IP has one limitation: the tuning circuit can't handle the async
sdio device interrupt correctly. When sdio device use 4 data lines,
async sdio interrupt will use the shared DAT[1], if enable auto tuning
circuit to check these 4 data lines, include the DAT[1], this circuit
will detect this interrupt, take this as data on DAT[1], and adjust the
delay cell wrongly, finally will cause the DATA/CMD CRC error.
So for SDIO device, only enable DAT[0] and CMD line for auto tuning.
To distinguish the card type during card init, involve init_card().
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221223025022.1893102-3-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Clear auto tuning bit when reset tuning, and enable auto tuning
only after tuning done successfully for both standard tuning and
manual tuning.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221223025022.1893102-2-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The SDHI/eMMC IPs found with the RZ/V2M (a.k.a. r9a09g011), are
very similar to the ones found in R-Car Gen3, but they are not
exactly the same, and as a result need an SoC specific compatible
string for fine tuning driver support.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221213230129.549968-4-fabrizio.castro.jz@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We need the serial/tty changes into this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert various parameter names for ->dtr_rts() and related functions
from onoff, on, and raise to active.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert the raise/on parameter in ->dtr_rts() to bool through the
callchain. The parameter is used like bool. In USB serial, there
remains a few implicit bool -> larger type conversions because some
devices use u8 in their control messages.
In moxa_tiocmget(), dtr variable was reused for line status which
requires int so use a separate variable for status.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Return boolean from ->carrier_raised() instead of 0 and 1. Make the
return type change also to tty_port_carrier_raised() that makes the
->carrier_raised() call (+ cd variable in moxa into which its return
value is stored).
Also cleans up a few unnecessary constructs related to this change:
return xx ? 1 : 0;
-> return xx;
if (xx)
return 1;
return 0;
-> return xx;
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The s3c24xx platform is gone, so this driver can be removed as well.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
All board support that was marked as 'unused' earlier can
now be removed, leaving the five machines that that still
had someone using them in 2022, or that are supported in
qemu.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The cns3xxx platform is gone, so this driver is now orphaned.
Cc: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
If the controller is suspended by runtime PM, the clock is already
disabled, so do not try to disable it again during removal. Use
pm_runtime_disable() to flush any pending runtime PM transitions.
Fixes: 9a8e1e8cc2c0 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220810022509.43743-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Current code logic may be impacted by the setting of ROM/Bootloader,
so unmask these bits first, then setting these bits accordingly.
Fixes: 2b16cf326b70 ("mmc: sdhci-esdhc-imx: move tuning static configuration into hwinit function")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221207112315.1812222-1-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- A few minor improvements and cleanups
MMC host:
- Remove some redundant calls to local_irq_{save,restore}()
- Replace kmap_atomic() with kmap_local_page()
- Take return values from mmc_add_host() into account
- dw_mmc-pltfm: Add support to configure clk-phase for socfpga
- hsq: Minimize latency by using a fifo to dispatch requests
- litex_mmc: Fixup corner case for polling mode
- mtk-sd: Add inline crypto engine clock control
- mtk-sd: Add support for the mediatek MT7986 variant
- renesas_sdhi: Improve reset from HS400 mode
- renesas_sdhi: Take DMA end interrupts into account
- sdhci: Avoid unnecessary update of clock
- sdhci: Fix an SD tuning issue
- sdhci-brcmst: Add Kamal Dasu as maintainer for the Broadcom driver
- sdhci-esdhc-imx: Improve tuning logic
- sdhci-esdhc-imx: Improve support for the imxrt1050 variant
- sdhci_f_sdh30: Add support for non-removable media
- sdhci_f_sdh30: Add support for the Socionext F_SDH30_E51 variant
- sdhci_f_sdh30: Add reset control support
- sdhci-msm: Add support for the Qcom SM8550/SM8350/SM6375 variants
- sdhci-msm: Add support for the Qcom MSM8976 variant
- sdhci-of-arasan: Add support for dynamic configuration
- sdhci-of-esdhc: Limit the clock frequency to confirm to spec
- sdhci-pci: Enable asynchronous probe
- sdhci-sprd: Improve card detection
- sdhci-tegra: Improve reset support
- sdhci-tegra: Add support to program MC stream ID
- sunplus-mmc: Add new mmc driver for the Sunplus SP7021 controller
- vub300: Fix warning splat for SDIO irq
MEMSTICK core:
- memstick: A few minor improvements and cleanups
CLK/IOMMU:
- clk: socfpga: Drop redundant support for clk-phase for the SD/MMC clk
- iommu: Add tegra specific helper to get stream_id"
* tag 'mmc-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (108 commits)
mmc: sdhci-sprd: Disable CLK_AUTO when the clock is less than 400K
mmc: sdhci-of-esdhc: Modify mismatched function name
memstick/mspro_block: Convert to use sysfs_emit()/sysfs_emit_at() APIs
mmc: sdhci-tegra: Issue CMD and DAT resets together
mmc: sdhci-tegra: Add support to program MC stream ID
mmc: sdhci-tegra: Separate Tegra194 and Tegra234 SoC data
mmc: sdhci-tegra: Sort includes alphabetically
iommu/tegra: Add tegra_dev_iommu_get_stream_id() helper
iommu: Add note about struct iommu_fwspec usage
mmc: sdhci-brcmstb: Resolve "unused" warnings with CONFIG_OF=n
dt-bindings: mmc: sdhci-msm: allow dma-coherent
dt-bindings: mmc: sdhci-msm: drop properties mentioned in common MMC
dt-bindings: mmc: sdhci-msm: cleanup style
dt-bindings: mmc: sdhci-am654: cleanup style
dt-bindings: mmc: sdhci: document sdhci-caps and sdhci-caps-mask
mmc: vub300: fix warning - do not call blocking ops when !TASK_RUNNING
MAINTAINERS: Update maintainer for SDHCI Broadcom BRCMSTB driver
mmc: sdhci-of-esdhc: limit the SDHC clock frequency
mmc: sdhci: Remove unneeded semicolon
mmc: core: Normalize the error handling branch in sd_read_ext_regs()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
|
|
When the clock is less than 400K, some SD cards fail to initialize
because CLK_AUTO is enabled.
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221207051909.32126-1-wenchao.chen@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
No functional modification involved.
drivers/mmc/host/sdhci-of-esdhc.c:243: warning: expecting prototype for _fixup(). Prototype was for esdhc_writel_fixup() instead.
drivers/mmc/host/sdhci-of-esdhc.c:117: warning: expecting prototype for _fixup(). Prototype was for esdhc_readl_fixup() instead.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3397
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221209034134.38477-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case of error condition to avoid system crash Tegra SDMMC controller
requires CMD and DAT resets issued together. SDHCI controller FSM goes
into bad state due to rapid SD card hot-plug event. Issuing reset on the
CMD FSM before DATA FSM results in kernel panic, hence add support to
issue CMD and DAT resets together.
This is applicable to Tegra186 and later chips.
Signed-off-by: Aniruddha TVS Rao <anrao@nvidia.com>
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221206165945.3551774-7-thierry.reding@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SMMU clients are supposed to program stream ID from their respective
address spaces instead of MC override. Define NVQUIRK_PROGRAM_STREAMID
and use it to program SMMU stream ID from the SDMMC client address
space.
Signed-off-by: Aniruddha TVS Rao <anrao@nvidia.com>
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221206165945.3551774-6-thierry.reding@gmail.com
[Ulf: Fixed a checkpatch error]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Create new SoC data structure for Tegra234 platforms. Additional
features, tap value configurations are added/updated for Tegra234
platform hence separate Tegra194 and Tegra234 SoC data.
Signed-off-by: Aniruddha Tvs Rao <anrao@nvidia.com>
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221206165945.3551774-5-thierry.reding@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Sort includes alphabetically to make it easier to add new ones
subsequently.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221206165945.3551774-4-thierry.reding@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
With W=1, we can see this gcc warning:
drivers/mmc/host/sdhci-brcmstb.c:182:34: warning: ‘sdhci_brcm_of_match’ defined but not used [-Wunused-const-variable=]
182 | static const struct of_device_id sdhci_brcm_of_match[] = {
| ^~~~~~~~~~~~~~~~~~~
Rather than play around more with #ifdef's, the simplest solution is to
just mark this __maybe_unused.
Fixes: 50bfe185c42a ("mmc: sdhci-brcmstb: Allow building with COMPILE_TEST")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202212060700.NjMecjxS-lkp@intel.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221205160353.1.I5fa28f1045f17fb9285d507accf139f8b2a8f4b5@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
vub300_enable_sdio_irq() works with mutex and need TASK_RUNNING here.
Ensure that we mark current as TASK_RUNNING for sleepable context.
[ 77.554641] do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff92a72c1d>] sdio_irq_thread+0x17d/0x5b0
[ 77.554652] WARNING: CPU: 2 PID: 1983 at kernel/sched/core.c:9813 __might_sleep+0x116/0x160
[ 77.554905] CPU: 2 PID: 1983 Comm: ksdioirqd/mmc1 Tainted: G OE 6.1.0-rc5 #1
[ 77.554910] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, BIOS BECFL357.86A.0081.2020.0504.1834 05/04/2020
[ 77.554912] RIP: 0010:__might_sleep+0x116/0x160
[ 77.554920] RSP: 0018:ffff888107b7fdb8 EFLAGS: 00010282
[ 77.554923] RAX: 0000000000000000 RBX: ffff888118c1b740 RCX: 0000000000000000
[ 77.554926] RDX: 0000000000000001 RSI: 0000000000000004 RDI: ffffed1020f6ffa9
[ 77.554928] RBP: ffff888107b7fde0 R08: 0000000000000001 R09: ffffed1043ea60ba
[ 77.554930] R10: ffff88821f5305cb R11: ffffed1043ea60b9 R12: ffffffff93aa3a60
[ 77.554932] R13: 000000000000011b R14: 7fffffffffffffff R15: ffffffffc0558660
[ 77.554934] FS: 0000000000000000(0000) GS:ffff88821f500000(0000) knlGS:0000000000000000
[ 77.554937] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 77.554939] CR2: 00007f8a44010d68 CR3: 000000024421a003 CR4: 00000000003706e0
[ 77.554942] Call Trace:
[ 77.554944] <TASK>
[ 77.554952] mutex_lock+0x78/0xf0
[ 77.554973] vub300_enable_sdio_irq+0x103/0x3c0 [vub300]
[ 77.554981] sdio_irq_thread+0x25c/0x5b0
[ 77.555006] kthread+0x2b8/0x370
[ 77.555017] ret_from_fork+0x1f/0x30
[ 77.555023] </TASK>
[ 77.555025] ---[ end trace 0000000000000000 ]---
Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87dc45b122d26d63c80532976813c9365d7160b3.1670140888.git.deren.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The highest clock frequency for eMMC HS200 mode on ls1043a
is 116.7Mhz according to its specification.
So add the limit to gate the frequency.
Signed-off-by: Andy Tang <andy.tang@nxp.com>
Link: https://lore.kernel.org/r/20221202075905.25363-1-andy.tang@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The semicolon after the "}" is unneeded.
Signed-off-by: zhang songyi <zhang.songyi@zte.com.cn>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/202212021031575255977@zte.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Let's use pr_err() to output the error messages and let's extend a comment
to clarify why returning 0 (success) in one case make sense.
Fixes: c784f92769ae ("mmc: core: Read the SD function extension registers for power management")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
[Ulf: Clarified the comment and the commit-msg]
Link: https://lore.kernel.org/r/20221130134920.2109-1-thunder.leizhen@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
To avoid glitches on the clock line, the card clock is disabled when making
timing changes. Do not do that separately for HISPD and UHS settings.
Tested-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221128133259.38305-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Current next_tag selection will cause a large delay in some requests and
destroy the scheduling results of the block scheduling layer. Because the
issued mrq tags cannot ensure that each time is sequential, especially when
the IO load is heavy. In the fio performance test, we found that 4k random
read data was sent to mmc_hsq to start calling request_atomic It takes
nearly 200ms to process the request, while mmc_hsq has processed thousands
of other requests. So we use fifo here to ensure the first in, first out
feature of the request and avoid adding additional delay to the request.
Reviewed-by: Wenchao Chen <wenchao.chen@unisoc.com>
Signed-off-by: Michael Wu <michael@allwinnertech.com>
Link: https://lore.kernel.org/r/20221128093847.22768-1-michael@allwinnertech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
