| Age | Commit message (Collapse) | Author |
|---|
|
Do not assume that hardware has been programmed with the default mask,
but instead read the input set registers to determine what is currently
programmed. This ensures that all programmed filters match exactly how
the hardware will interpret them, avoiding confusion regarding filter
behavior.
This sets the initial ground-work for allowing custom input sets where
some fields are disabled. A future patch will fully implement this
feature.
Instead of using bitwise negation, we'll just explicitly check for the
correct value. The use of htonl and htons are used to silence sparse
warnings. The compiler should be able to handle the constant value and
avoid actually performing a byteswap.
Change-Id: I3d8db46cb28ea0afdaac8c5b31a2bfb90e3a4102
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current implementation of .set_rxnfc does not properly read the mask
field for filter entries. This results in incorrect driver behavior, as
we do not reject filters which have masks set to ignore some fields. The
current implementation simply assumes that every part of the tuple or
"input set" is specified. This results in filters not behaving as
expected, and not working correctly.
As a first step in supporting some partial filters, add code which
checks the mask fields and rejects any filters which do not have an
acceptable mask. For now, we just assume that all fields must be set.
This will get the driver one step towards allowing some partial filters.
At a minimum, the ethtool commands which previously installed filters
that would not function will now return a non-zero exit code indicating
failure instead.
We should now be meeting the minimum requirements of the .set_rxnfc API,
by ensuring that all filters we program have a valid mask value for each
field.
Finally, add code to report the mask correctly so that the ethtool
command properly reports the mask to the user.
Note that the typecast to (__be16) when checking source and destination
port masks is required because the ~ bitwise negation operator does not
correctly handle variables other than integer size.
Change-Id: Ia020149e07c87aa3fcec7b2283621b887ef0546f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The previous code relied on i40e_match_fdir_input_set to determine when
determining whether to free the old filter. Change this code so that we
simply unconditionally delete the old filter, even if it's identical to
the new filter. This ensures that we don't leak any memory, and that we
always update the filters as expected.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Although we will fail the filter later due to checking flow_type which
will have a bogus invalid type, it is possible future refactoring will
remove this hidden failure case. Avoid a possible issue in the future by
explicitly checking the flow type at the start.
Change-Id: Ia98eb26f7b93ccbe38c7141e8f203ef496fc6598
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Refactor the exit flow of the i40e_add_fdir_ethtool function. Move the
input_label to the end of the function, removing the dependency on
having a non-zero return value. Add a comment explaining why it is ok
not to free the fdir data structure, because the structure is now stored
in the fdir_filter_list.
Change-Id: I723342181d59cd0c9f3b31140c37961ba37bb242
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The code originally included src_ip and dst_ip with enough space to
support ipv6 filters. However, no actual support for ipv6 filters has
been implemented. Thus, remove the arrays and just use __be32 values.
Should ipv6 support be added in the future, we can replace these with
a union that has sizes for both values.
Change-Id: I1bc04032244a80eb6ebc8a4e6c723a4a665c1dd5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A previous commit introduced a field that tracks the features
that are disabled due to HW resource limitations as opposed
to the featured disabled by the user. This patch changes the
name of the field to make it more readable since it might get
confusing when looking at code containing both the flags
field and the auto_disable_features field together.
Change-ID: Idcc9888659698f6fe3ccff17c8c3f09b5026f708
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently ethtool -e will error out with a X722 interface
as its EEPROM has a scope limit at offset 0x5B9FFF.
This patch fixes the issue by setting the EEPROM length to
the scope limit to avoid NVM read failure beyond that.
Change-ID: I0b7d4dd6c7f2a57cace438af5dffa0f44c229372
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Ethtool support needs to save more PHY information. The
added information includes FEC capabilities and 25G link
types. Without this change it is possible to lose 25G or
FEC settings by using ethtool.
Change-ID: Ie42255b1e901ffbf9583b8c46466a54894114280
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Due to the resolution of the register controlling interrupt rate
limiting, setting certain values for the interrupt rate limit make it
appear as though the limiting is not completely accurate. The problem
is that the interrupt rate limit is getting rounded down to the nearest
multiple of 4. This patch fixes the problem by adding some feedback to
the user as to the actual interrupt rate limit being used when it
differs from the requested limit. Without this patch setting interrupt
rate limits may appear to behave inaccurately.
Change-ID: I3093cf3f2d437d35a4c4f4bb5af5ce1b85ab21b7
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch refactors the macro INTRL_USEC_TO_REG into a static inline
function and fixes a couple subtle bugs caused by the macro.
This patch fixes a bug which was caused by passing a bad register value
to the firmware. If enabling interrupt rate limiting, a non-zero value
for the rate limit must be used. Otherwise the firmware sets the
interrupt rate limit to the maximum value. Due to the limited
resolution of the register, attempting to set a value of 1, 2, or 3
would be rounded down to 0 and limiting was left enabled, causing
unexpected behavior.
This patch also fixes a possible bug in which using the macro itself can
introduce unintended side-affects because the macro argument is used
more than once in the macro definition (e.g. a variable post-increment
argument would perform a double increment on the variable).
Without this patch, attempting to set interrupt rate limits of 1, 2, or
3 results in unexpected behavior and future use of this macro could
cause subtle bugs.
Change-Id: I83ac842de0ca9c86761923d6e3a4d7b1b95f2b3f
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A product decision has been made to defeature detection of PTP frames
over L4 (UDP) on the XL710 MAC. Do not advertise support for L4
timestamping.
Change-ID: I41fbb0f84ebb27c43e23098c08156f2625c6ee06
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add support for 25G devices - defines and data structures.
One tricky part here is that the firmware support for these
Devices introduces a mismatch between the PHY type enum and
the bitfields for the phy types.
This change creates a macro and uses it to increment the 25G
PHY values when creating 25G bitfields.
Change-ID: I69b24d837d44cf9220bf5cb8dd46c5be89ce490b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Before this patch "ethtool -p" was not blinking the LEDs on boards
with 1G BaseT PHYs.
This commit identifies 1G BaseT boards as having the LEDs connected
to the MAC. Also, renamed the flag to be more descriptive of usage.
The flag is now I40E_FLAG_PHY_CONTROLS_LEDS.
Change-ID: I4eb741da9780da7849ddf2dc4c0cb27ffa42a801
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
memcpy replaced with single memcpy call in ethtool.
Change-ID: I3f5bef6bcc593412c56592c6459784db41575a0a
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes the problem where the ethtool Supported link
modes list backplane interfaces on X722 devices for 10GbE with
SFP+ and Cortina retimer. This patch fixes the problem by setting
and using a flag for this particular device since the backplane
interface is only between the internal PHY and the retimer and it
should not be seen by the user as they cannot use it.
Without this patch, the user wrongly thinks that backplane interfaces
are supported on their device when they actually are not.
Change-ID: I3882bc2928431d48a2db03a51a713a1f681a79e9
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On SPARC, writel() should not be used to write directly to memory
address but only to memory mapped I/O address otherwise it causes
data access exception.
Commit 147e81ec75689 ("i40e: Test memory before ethtool alloc
succeeds") introduced a code that uses memory address to fake the HW
tail address and attempt to write to that address using writel()
causes kernel panic on SPARC. The issue is reproduced while changing
number of descriptors using ethtool.
This change resolves the panic by using HW read-only memory mapped
I/O register to fake HW tail address instead memory address.
e.g.
> ethtool -G eth2 tx 2048 rx 2048
i40e 0000:03:00.2 eth2: Changing Tx descriptor count from 512 to 2048.
i40e 0000:03:00.2 eth2: Changing Rx descriptor count from 512 to 2048
sun4v_data_access_exception: ADDR[fff8001f9734a000] CTX[0000]
TYPE[0004], going.
\|/ ____ \|/
"@'/ .. \`@"
/_| \__/ |_\
\__U_/
ethtool(3273): Dax [#1]
CPU: 9 PID: 3273 Comm: ethtool Tainted: G E
4.8.0-linux-net_temp+ #7
task: fff8001f96d7a660 task.stack: fff8001f97348000
TSTATE: 0000009911001601 TPC: 00000000103189e4 TNPC: 00000000103189e8 Y:
00000000 Tainted: G E
TPC: <i40e_alloc_rx_buffers+0x124/0x260 [i40e]>
g0: fff8001f4eb64000 g1: 00000000000007ff g2: fff8001f9734b92c g3:
00203e0000000000
g4: fff8001f96d7a660 g5: fff8001fa6704000 g6: fff8001f97348000 g7:
0000000000000001
o0: 0006000046706928 o1: 00000000db3e2000 o2: fff8001f00000000 o3:
0000000000002000
o4: 0000000000002000 o5: 0000000000000001 sp: fff8001f9734afc1 ret_pc:
0000000010318a64
RPC: <i40e_alloc_rx_buffers+0x1a4/0x260 [i40e]>
l0: fff8001f4e8bffe0 l1: fff8001f4e8cffe0 l2: 00000000000007ff l3:
00000000ff000000
l4: 0000000000ff0000 l5: 000000000000ff00 l6: 0000000000cda6a8 l7:
0000000000e822f0
i0: fff8001f96380000 i1: 0000000000000000 i2: 00203edb00000000 i3:
0006000046706928
i4: 0000000002086320 i5: 0000000000e82370 i6: fff8001f9734b071 i7:
00000000103062d4
I7: <i40e_set_ringparam+0x3b4/0x540 [i40e]>
Call Trace:
[00000000103062d4] i40e_set_ringparam+0x3b4/0x540 [i40e]
[000000000094e2f8] dev_ethtool+0x898/0xbe0
[0000000000965570] dev_ioctl+0x250/0x300
[0000000000923800] sock_do_ioctl+0x40/0x60
[000000000092427c] sock_ioctl+0x7c/0x280
[00000000005ef040] vfs_ioctl+0x20/0x60
[00000000005ef5d4] do_vfs_ioctl+0x194/0x4c0
[00000000005ef974] SyS_ioctl+0x74/0xa0
[0000000000406214] linux_sparc_syscall+0x34/0x44
Disabling lock debugging due to kernel taint
Caller[00000000103062d4]: i40e_set_ringparam+0x3b4/0x540 [i40e]
Caller[000000000094e2f8]: dev_ethtool+0x898/0xbe0
Caller[0000000000965570]: dev_ioctl+0x250/0x300
Caller[0000000000923800]: sock_do_ioctl+0x40/0x60
Caller[000000000092427c]: sock_ioctl+0x7c/0x280
Caller[00000000005ef040]: vfs_ioctl+0x20/0x60
Caller[00000000005ef5d4]: do_vfs_ioctl+0x194/0x4c0
Caller[00000000005ef974]: SyS_ioctl+0x74/0xa0
Caller[0000000000406214]: linux_sparc_syscall+0x34/0x44
Caller[0000000000107154]: 0x107154
Instruction DUMP: e43620c8
e436204a c45e2038
<c2a083a0> 82102000
81cfe008 90086001
82102000 81cfe008
Kernel panic - not syncing: Fatal exception
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Separate the global private flags and the regular private flags per
interface into two arrays. Future additions of private flags will not
need to be duplicated which may lead to buggy code. Also rename
"i40e_priv_flags_strings_gl" to "i40e_gl_priv_flags_strings" for
clarity, as it reads more naturally.
Change-ID: I68caef3c9954eb7da342d7f9d20f2873186f2758
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Removed some of unnecessary if statements and unreachable code found by
static code analysis tool.
The return value of i40e_vsi_control_rings(..., false) is always 0. So,
test for non-zero will never be true. The function has been split into
"int i40e_vsi_start_rings()" and "void i40e_vsi_stop_rings()" for better
understanding.
Similarly, the function i40e_vsi_kill_vlan() never fails. So, checking
for return value is also unnecessary. Function definition changed to void.
The i40e_loopback_test() function is not implemented. The function and
all references to loopback testing were removed.
Change-ID: Id45cf66f6689ce2bc4e887de13f073e30e8431bd
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a common method for finding a VSI by type. The main
motivation for doing this is that the Flow Director path actually had two
ways of handling this, one stopped on first match and one did not. This
patch makes it so that all callers of this function will get the same
approach for finding a VSI.
Change-ID: Ibf25de8acd8466582520694424aa87da66965fbd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
So the i40e driver had a really convoluted configuration for how to handle
the debug flags contained in msg_level. Part of the issue is that the
driver has its own 32 bit mask that it was using to track a separate set of
debug features. From what I can tell it was trying to use the upper 4 bits
to determine if the value was meant to represent a bit-mask or the numeric
value provided by debug level.
What this patch does is clean this up by compressing those 4 bits into bit
31, as a result we just have to perform a check against the value being
negative to determine if we are looking at a debug level (positive), or a
debug mask (negative). The debug level will populate the msg_level, and
the debug mask will populate the debug_mask in the hardware struct.
I added similar logic for ethtool. If the value being provided has bit 31
set we assume the value being provided is a debug mask, otherwise we assume
it is a msg_enable mask. For displaying we only provide the msg_enable,
and if debug_mask is in use we will print it to the dmesg log.
Lastly I removed the debugfs interface. It is redundant with what we
already have in ethtool and really doesn't belong anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Move some data to text
$ size drivers/net/ethernet/intel/i40e/i40e_ethtool.o*
text data bss dec hex filename
25012 0 32 25044 61d4 drivers/net/ethernet/intel/i40e/i40e_ethtool.o.new
22868 2120 32 25020 61bc drivers/net/ethernet/intel/i40e/i40e_ethtool.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit a75e8005d506f3 ("i40e: queue-specific settings for interrupt
moderation") the i40e driver gained support for setting interrupt
moderation values per queue. This patch adds support for this feature
to the i40evf driver as well. In addition, a few changes are made to
the i40e implementation to add function header documentation comments,
as well.
This behaves in a similar fashion to the implementation in i40e. Thus,
requesting the moderation value when no queue is provided will report
queue 0 value, while setting the value without a queue will set all
queues at once.
Change-ID: I1f310a57c8e6c84a8524c178d44d1b7a6d3a848e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Some locations that disable ATR accidentally used the "full" disable by
disabling the flag in the standard flags field. This incorrectly forces
ATR off permanently instead of temporarily disabling it. In addition,
some code locations accidentally set the ATR flag enabled when they only
meant to clear the auto_disable_flags. This results in ignoring the
user's ethtool private flag settings.
Additionally, when disabling ATR via ethtool, we did not perform a flush
of the FD table. This results in the previously assigned ATR rules still
functioning which was not expected.
Cleanup all these areas so that automatic disable uses only the
auto_disable_flag. Fix the flush code so that we can trigger a flush
even when we've disabled ATR and SB support, as otherwise the flush
doesn't work. Fix ethtool setting to actually request a flush. Fix
NETIF_F_NTUPLE flag to only clear the auto_disable setting and not
enable the full feature.
Change-ID: Ib2486111f8031bd16943e9308757b276305c03b5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previously, when using ethtool to change the RSS hash key, ethtool would
report back saying the old key was still being used and no error was
reported. It was unclear whether it was being reported incorrectly or
being set incorrectly. Debugging revealed 'i40e_set_rxfh()' returned
zero immediately instead of setting the key because a user defined
indirection table is not supplied when changing the hash key.
This fix instead changes it such that if an indirection table is not
supplied, then a default one is created and the hash key is now
correctly set.
Change-ID: Iddb621897ecf208650272b7ee46702cad7b69a71
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i is defined as int but output as %u several times.
Adjust the format identifiers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements a feature change which allows using ethtool to set
RSS hash opts using less than four parameters if desired.
Change-ID: I0fbb91255d81e997c456697c21ac39cc9754821b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If a driver is unable to maintain all current user supplied settings
from ethtool (or other sources), it is not ok for a user request to
succeed and silently trample over previous configuration.
To that end, if you change the number of channels, it must not be
allowed to reduce the number of channels (queues) below the current
flow director filter rules targets. In this case, return -EINVAL when
a request to reduce the number of channels would do so. In addition
log a warning to the kernel buffer explaining why we failed, and report
the rules which prevent us from lowering the number of channels.
Change-ID: If41464d63d7aab11cedf09e4f3aa1a69e21ffd88
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Adding the missing link advertise for some X710 NICs.
This can be observed by simply calling ethtool on the interface.
root@rhel7:~ # ethtool eth0
Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Advertised link modes: Not reported
[...]
With fix applied.
root@rhel7:~ # ethtool eth0
Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Advertised link modes: 10000baseT/Full
[...]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When link is down, Advertised Link Modes was wrongly displaying full
supported link modes instead of Advertised link mode. Added conditional
checks in order to make sure correct Advertised link modes are
displayed when the link is down.
Change-ID: I8a61413f9ee174149c7a33157b5f0b0a8da9842d
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Removing this code which wasn't allowing 100BaseT to show up in the supported
link modes for 10GBaseT PHYs.
Change-ID: Iada2eafa7ef6b4bac9a2a1380ff533ae5de51e1d
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When a Direct Attach (DA) cable is used, if the i40e_set_settings
function is called it would return an error. Add the DA type so
the function won't fail.
Change-ID: I2b802f27a5d91cfefa72fd1f852acb4d74647a8e
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previously we were only looking at the FW supported PHY types if link
was down, because we want to be more specific when link is up. This
refactor changes this. When link is down, we still rely on the FW
supported PHY types, but when link is up, we select the possible
supported link modes from what we know about the current PHY type, and
AND that with the FW supported PHY types.
Change-ID: Ice5dad83f2a17932b0b8b59f07439696ad6aa013
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.
The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.
For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.
Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
vf-true-promisc-support: off
to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on
At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic
Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
interactions
Add flag to tell firmware to disable link on all ports.
This patch changes the bits set for telling firmware the PHY needs
to be modified by driver. Without this patch, the setting will only
set that mode for the current port on the device. Because the
MDIO interface is common for the copper device. The command needs to
set the mode for all ports.
Change-ID: I8baa7da91d384291ac95b41ae1a516604f8eb67f
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When testing on systems with very limited amounts of RAM, a bug was
found where, while changing the number of descriptors using ethtool,
the driver didn't test the limits of system memory before permanently
assuming it would be able to get receive buffer memory.
Work around this issue by pre-allocation of the receive buffer
memory, in the "ghost" ring, which is then used during reinit
using the new ring length.
Change-Id: I92d7a5fb59a6c884b2efdd1ec652845f101c3359
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is part 1 of the Rx refactor series, just including
changes to i40e.
This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.
In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split
Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A little bit of code cleanup in prep for more cloud filter work.
Change-ID: I0dc33ce0d4c207944336a07437640fef920c100c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
100baseT/Full is now listed and supported link mode for 10GBaseT PHY.
This is a fix to list all the supported link modes of 10GBaseT PHY.
Change-ID: If2be3212ef0fef85fd5d6e4550c7783de2f915e9
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements set_per_queue_coalesce for i40e driver.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements get_per_queue_coalesce for i40e driver.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.
We can't use AdminQ calls in i40e_clear_hw() because the HW is being
initialized and the AdminQ is not alive. We recently added an AQ
related replacement for reading PFLAN_QALLOC, and this patch puts
back the original register read.
Change-ID: Ib027168c954a5733299aa3a4ce5f8218c6bb5636
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes a problem where the ethtool identify adapter
functionality did not work for some copper PHY's. Without this
patch, the blink led functionality fails on some parts. This
patch adds PHY write code to blink led's on parts where this
functionality is contained in the PHY rather than the MAC.
Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make sure we return EBUSY while finishing up a reset, and add a few bits
for better debug messages.
Change-ID: I23f6c28a8d96d7aa171abcc265737cec7826c292
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.
Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.
Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The new parameters for add_veb allow us to enable and disable VEB stats,
so let's use them.
Update copyright year.
Change-ID: Ie6e68c68e2d1d459e42168eda661051b56bf0a65
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
