summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel
AgeCommit message (Collapse)Author
2024-07-11i40e: fix: remove needless retries of NVM updateAleksandr Loktionov
Remove wrong EIO to EGAIN conversion and pass all errors as is. After commit 230f3d53a547 ("i40e: remove i40e_status"), which should only replace F/W specific error codes with Linux kernel generic, all EIO errors suddenly started to be converted into EAGAIN which leads nvmupdate to retry until it timeouts and sometimes fails after more than 20 minutes in the middle of NVM update, so NVM becomes corrupted. The bug affects users only at the time when they try to update NVM, and only F/W versions that generate errors while nvmupdate. For example, X710DA2 with 0x8000ECB7 F/W is affected, but there are probably more... Command for reproduction is just NVM update: ./nvmupdate64 In the log instead of: i40e_nvmupd_exec_aq err I40E_ERR_ADMIN_QUEUE_ERROR aq_err I40E_AQ_RC_ENOMEM) appears: i40e_nvmupd_exec_aq err -EIO aq_err I40E_AQ_RC_ENOMEM i40e: eeprom check failed (-5), Tx/Rx traffic disabled The problematic code did silently convert EIO into EAGAIN which forced nvmupdate to ignore EAGAIN error and retry the same operation until timeout. That's why NVM update takes 20+ minutes to finish with the fail in the end. Fixes: 230f3d53a547 ("i40e: remove i40e_status") Co-developed-by: Kelvin Kang <kelvin.kang@intel.com> Signed-off-by: Kelvin Kang <kelvin.kang@intel.com> Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Tony Brelinski <tony.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20240710224455.188502-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-10e1000e: fix force smbus during suspend flowVitaly Lifshits
Commit 861e8086029e ("e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue") resolved a PHY access loss during suspend on Meteor Lake consumer platforms, but it affected corporate systems incorrectly. A better fix, working for both consumer and corporate systems, was proposed in commit bfd546a552e1 ("e1000e: move force SMBUS near the end of enable_ulp function"). However, it introduced a regression on older devices, such as [8086:15B8], [8086:15F9], [8086:15BE]. This patch aims to fix the secondary regression, by limiting the scope of the changes to Meteor Lake platforms only. Fixes: bfd546a552e1 ("e1000e: move force SMBUS near the end of enable_ulp function") Reported-by: Todd Brandt <todd.e.brandt@intel.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218940 Reported-by: Dieter Mummenschanz <dmummenschanz@web.de> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218936 Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240709203123.2103296-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-09i40e: Fix XDP program unloading while removing the driverMichal Kubiak
The commit 6533e558c650 ("i40e: Fix reset path while removing the driver") introduced a new PF state "__I40E_IN_REMOVE" to block modifying the XDP program while the driver is being removed. Unfortunately, such a change is useful only if the ".ndo_bpf()" callback was called out of the rmmod context because unloading the existing XDP program is also a part of driver removing procedure. In other words, from the rmmod context the driver is expected to unload the XDP program without reporting any errors. Otherwise, the kernel warning with callstack is printed out to dmesg. Example failing scenario: 1. Load the i40e driver. 2. Load the XDP program. 3. Unload the i40e driver (using "rmmod" command). The example kernel warning log: [ +0.004646] WARNING: CPU: 94 PID: 10395 at net/core/dev.c:9290 unregister_netdevice_many_notify+0x7a9/0x870 [...] [ +0.010959] RIP: 0010:unregister_netdevice_many_notify+0x7a9/0x870 [...] [ +0.002726] Call Trace: [ +0.002457] <TASK> [ +0.002119] ? __warn+0x80/0x120 [ +0.003245] ? unregister_netdevice_many_notify+0x7a9/0x870 [ +0.005586] ? report_bug+0x164/0x190 [ +0.003678] ? handle_bug+0x3c/0x80 [ +0.003503] ? exc_invalid_op+0x17/0x70 [ +0.003846] ? asm_exc_invalid_op+0x1a/0x20 [ +0.004200] ? unregister_netdevice_many_notify+0x7a9/0x870 [ +0.005579] ? unregister_netdevice_many_notify+0x3cc/0x870 [ +0.005586] unregister_netdevice_queue+0xf7/0x140 [ +0.004806] unregister_netdev+0x1c/0x30 [ +0.003933] i40e_vsi_release+0x87/0x2f0 [i40e] [ +0.004604] i40e_remove+0x1a1/0x420 [i40e] [ +0.004220] pci_device_remove+0x3f/0xb0 [ +0.003943] device_release_driver_internal+0x19f/0x200 [ +0.005243] driver_detach+0x48/0x90 [ +0.003586] bus_remove_driver+0x6d/0xf0 [ +0.003939] pci_unregister_driver+0x2e/0xb0 [ +0.004278] i40e_exit_module+0x10/0x5f0 [i40e] [ +0.004570] __do_sys_delete_module.isra.0+0x197/0x310 [ +0.005153] do_syscall_64+0x85/0x170 [ +0.003684] ? syscall_exit_to_user_mode+0x69/0x220 [ +0.004886] ? do_syscall_64+0x95/0x170 [ +0.003851] ? exc_page_fault+0x7e/0x180 [ +0.003932] entry_SYSCALL_64_after_hwframe+0x71/0x79 [ +0.005064] RIP: 0033:0x7f59dc9347cb [ +0.003648] Code: 73 01 c3 48 8b 0d 65 16 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 35 16 0c 00 f7 d8 64 89 01 48 [ +0.018753] RSP: 002b:00007ffffac99048 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 [ +0.007577] RAX: ffffffffffffffda RBX: 0000559b9bb2f6e0 RCX: 00007f59dc9347cb [ +0.007140] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 0000559b9bb2f748 [ +0.007146] RBP: 00007ffffac99070 R08: 1999999999999999 R09: 0000000000000000 [ +0.007133] R10: 00007f59dc9a5ac0 R11: 0000000000000206 R12: 0000000000000000 [ +0.007141] R13: 00007ffffac992d8 R14: 0000559b9bb2f6e0 R15: 0000000000000000 [ +0.007151] </TASK> [ +0.002204] ---[ end trace 0000000000000000 ]--- Fix this by checking if the XDP program is being loaded or unloaded. Then, block only loading a new program while "__I40E_IN_REMOVE" is set. Also, move testing "__I40E_IN_REMOVE" flag to the beginning of XDP_SETUP callback to avoid unnecessary operations and checks. Fixes: 6533e558c650 ("i40e: Fix reset path while removing the driver") Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240708230750.625986-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-03ice: use proper macro for testing bitPetr Oros
Do not use _test_bit() macro for testing bit. The proper macro for this is one without underline. _test_bit() is what test_bit() was prior to const-optimization. It directly calls arch_test_bit(), i.e. the arch-specific implementation (or the generic one). It's strictly _internal_ and shouldn't be used anywhere outside the actual test_bit() macro. test_bit() is a wrapper which checks whether the bitmap and the bit number are compile-time constants and if so, it calls the optimized function which evaluates this call to a compile-time constant as well. If either of them is not a compile-time constant, it just calls _test_bit(). test_bit() is the actual function to use anywhere in the kernel. IOW, calling _test_bit() avoids potential compile-time optimizations. The sensors is not a compile-time constant, thus most probably there are no object code changes before and after the patch. But anyway, we shouldn't call internal wrappers instead of the actual API. Fixes: 4da71a77fc3b ("ice: read internal temperature sensor") Acked-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240702171459.2606611-5-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-03ice: Reject pin requests with unsupported flagsJacob Keller
The driver receives requests for configuring pins via the .enable callback of the PTP clock object. These requests come into the driver with flags which modify the requested behavior from userspace. Current implementation in ice does not reject flags that it doesn't support. This causes the driver to incorrectly apply requests with such flags as PTP_PEROUT_DUTY_CYCLE, or any future flags added by the kernel which it is not yet aware of. Fix this by properly validating flags in both ice_ptp_cfg_perout and ice_ptp_cfg_extts. Ensure that we check by bit-wise negating supported flags rather than just checking and rejecting known un-supported flags. This is preferable, as it ensures better compatibility with future kernels. Fixes: 172db5f91d5f ("ice: add support for auxiliary input/output pins") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240702171459.2606611-4-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-03ice: Don't process extts if PTP is disabledJacob Keller
The ice_ptp_extts_event() function can race with ice_ptp_release() and result in a NULL pointer dereference which leads to a kernel panic. Panic occurs because the ice_ptp_extts_event() function calls ptp_clock_event() with a NULL pointer. The ice driver has already released the PTP clock by the time the interrupt for the next external timestamp event occurs. To fix this, modify the ice_ptp_extts_event() function to check the PTP state and bail early if PTP is not ready. Fixes: 172db5f91d5f ("ice: add support for auxiliary input/output pins") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240702171459.2606611-3-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-03ice: Fix improper extts handlingMilena Olech
Extts events are disabled and enabled by the application ts2phc. However, in case where the driver is removed when the application is running, a specific extts event remains enabled and can cause a kernel crash. As a side effect, when the driver is reloaded and application is started again, remaining extts event for the channel from a previous run will keep firing and the message "extts on unexpected channel" might be printed to the user. To avoid that, extts events shall be disabled when PTP is released. Fixes: 172db5f91d5f ("ice: add support for auxiliary input/output pins") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Co-developed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Milena Olech <milena.olech@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240702171459.2606611-2-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-01e1000e: Fix S0ix residency on corporate systemsDima Ruinskiy
On vPro systems, the configuration of the I219-LM to achieve power gating and S0ix residency is split between the driver and the CSME FW. It was discovered that in some scenarios, where the network cable is connected and then disconnected, S0ix residency is not always reached. This was root-caused to a subset of I219-LM register writes that are not performed by the CSME FW. Therefore, the driver should perform these register writes on corporate setups, regardless of the CSME FW state. This was discovered on Meteor Lake systems; however it is likely to appear on other platforms as well. Fixes: cc23f4f0b6b9 ("e1000e: Add support for Meteor Lake") Link: https://bugzilla.kernel.org/show_bug.cgi?id=218589 Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240628201754.2744221-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-23ice: Rebuild TC queues on VSI queue reconfigurationJan Sokolowski
TC queues needs to be correctly updated when the number of queues on a VSI is reconfigured, so netdev's queue and TC settings will be dynamically adjusted and could accurately represent the underlying hardware state after changes to the VSI queue counts. Fixes: 0754d65bd4be ("ice: Add infrastructure for mqprio support via ndo_setup_tc") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-06-19ice: Fix VSI list rule with ICE_SW_LKUP_LAST typeMarcin Szycik
Adding/updating VSI list rule, as well as allocating/freeing VSI list resource are called several times with type ICE_SW_LKUP_LAST, which fails because ice_update_vsi_list_rule() and ice_aq_alloc_free_vsi_list() consider it invalid. Allow calling these functions with ICE_SW_LKUP_LAST. This fixes at least one issue in switchdev mode, where the same rule with different action cannot be added, e.g.: tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \ dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF1_PR tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \ dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF2_PR Fixes: 0f94570d0cae ("ice: allow adding advanced rules") Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240618210206.981885-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-13ice: implement AQ download pkg retryWojciech Drewek
ice_aqc_opc_download_pkg (0x0C40) AQ sporadically returns error due to FW issue. Fix this by retrying five times before moving to Safe Mode. Sleep for 20 ms before retrying. This was tested with the 4.40 firmware. Fixes: c76488109616 ("ice: Implement Dynamic Device Personalization (DDP) download") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-06-13ice: fix 200G link speed message logPaul Greenwalt
Commit 24407a01e57c ("ice: Add 200G speed/phy type use") added support for 200G PHY speeds, but did not include 200G link speed message support. As a result the driver incorrectly reports Unknown for 200G link speed. Fix this by adding 200G support to ice_print_link_msg(). Fixes: 24407a01e57c ("ice: Add 200G speed/phy type use") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-06-13ice: avoid IRQ collision to fix init failure on ACPI S3 resumeEn-Wei Wu
A bug in https://bugzilla.kernel.org/show_bug.cgi?id=218906 describes that irdma would break and report hardware initialization failed after suspend/resume with Intel E810 NIC (tested on 6.9.0-rc5). The problem is caused due to the collision between the irq numbers requested in irdma and the irq numbers requested in other drivers after suspend/resume. The irq numbers used by irdma are derived from ice's ice_pf->msix_entries which stores mappings between MSI-X index and Linux interrupt number. It's supposed to be cleaned up when suspend and rebuilt in resume but it's not, causing irdma using the old irq numbers stored in the old ice_pf->msix_entries to request_irq() when resume. And eventually collide with other drivers. This patch fixes this problem. On suspend, we call ice_deinit_rdma() to clean up the ice_pf->msix_entries (and free the MSI-X vectors used by irdma if we've dynamically allocated them). On resume, we call ice_init_rdma() to rebuild the ice_pf->msix_entries (and allocate the MSI-X vectors if we would like to dynamically allocate them). Fixes: f9f5301e7e2d ("ice: Register auxiliary device to provide RDMA") Tested-by: Cyrus Lien <cyrus.lien@canonical.com> Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-06-13Revert "igc: fix a log entry using uninitialized netdev"Sasha Neftin
This reverts commit 86167183a17e03ec77198897975e9fdfbd53cb0b. igc_ptp_init() needs to be called before igc_reset(), otherwise kernel crash could be observed. Following the corresponding discussion [1] and [2] revert this commit. Link: https://lore.kernel.org/all/8fb634f8-7330-4cf4-a8ce-485af9c0a61a@intel.com/ [1] Link: https://lore.kernel.org/all/87o78rmkhu.fsf@intel.com/ [2] Fixes: 86167183a17e ("igc: fix a log entry using uninitialized netdev") Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240611162456.961631-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-05igc: Fix Energy Efficient Ethernet support declarationSasha Neftin
The commit 01cf893bf0f4 ("net: intel: i40e/igc: Remove setting Autoneg in EEE capabilities") removed SUPPORTED_Autoneg field but left inappropriate ethtool_keee structure initialization. When "ethtool --show <device>" (get_eee) invoke, the 'ethtool_keee' structure was accidentally overridden. Remove the 'ethtool_keee' overriding and add EEE declaration as per IEEE specification that allows reporting Energy Efficient Ethernet capabilities. Examples: Before fix: ethtool --show-eee enp174s0 EEE settings for enp174s0: EEE status: not supported After fix: EEE settings for enp174s0: EEE status: disabled Tx LPI: disabled Supported EEE link modes: 100baseT/Full 1000baseT/Full 2500baseT/Full Fixes: 01cf893bf0f4 ("net: intel: i40e/igc: Remove setting Autoneg in EEE capabilities") Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-6-e3563aa89b0c@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-05ice: map XDP queues to vectors in ice_vsi_map_rings_to_vectors()Larysa Zaremba
ice_pf_dcb_recfg() re-maps queues to vectors with ice_vsi_map_rings_to_vectors(), which does not restore the previous state for XDP queues. This leads to no AF_XDP traffic after rebuild. Map XDP queues to vectors in ice_vsi_map_rings_to_vectors(). Also, move the code around, so XDP queues are mapped independently only through .ndo_bpf(). Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-5-e3563aa89b0c@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-05ice: add flag to distinguish reset from .ndo_bpf in XDP rings configLarysa Zaremba
Commit 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") has placed ice_vsi_free_q_vectors() after ice_destroy_xdp_rings() in the rebuild process. The behaviour of the XDP rings config functions is context-dependent, so the change of order has led to ice_destroy_xdp_rings() doing additional work and removing XDP prog, when it was supposed to be preserved. Also, dependency on the PF state reset flags creates an additional, fortunately less common problem: * PFR is requested e.g. by tx_timeout handler * .ndo_bpf() is asked to delete the program, calls ice_destroy_xdp_rings(), but reset flag is set, so rings are destroyed without deleting the program * ice_vsi_rebuild tries to delete non-existent XDP rings, because the program is still on the VSI * system crashes With a similar race, when requested to attach a program, ice_prepare_xdp_rings() can actually skip setting the program in the VSI and nevertheless report success. Instead of reverting to the old order of function calls, add an enum argument to both ice_prepare_xdp_rings() and ice_destroy_xdp_rings() in order to distinguish between calls from rebuild and .ndo_bpf(). Fixes: efc2214b6047 ("ice: Add support for XDP") Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-4-e3563aa89b0c@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-05ice: remove af_xdp_zc_qps bitmapLarysa Zaremba
Referenced commit has introduced a bitmap to distinguish between ZC and copy-mode AF_XDP queues, because xsk_get_pool_from_qid() does not do this for us. The bitmap would be especially useful when restoring previous state after rebuild, if only it was not reallocated in the process. This leads to e.g. xdpsock dying after changing number of queues. Instead of preserving the bitmap during the rebuild, remove it completely and distinguish between ZC and copy-mode queues based on the presence of a device associated with the pool. Fixes: e102db780e1c ("ice: track AF_XDP ZC enabled queues in bitmap") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-3-e3563aa89b0c@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-05ice: fix reads from NVM Shadow RAM on E830 and E825-C devicesJacob Keller
The ice driver reads data from the Shadow RAM portion of the NVM during initialization, including data used to identify the NVM image and device, such as the ETRACK ID used to populate devlink dev info fw.bundle. Currently it is using a fixed offset defined by ICE_CSS_HEADER_LENGTH to compute the appropriate offset. This worked fine for E810 and E822 devices which both have CSS header length of 330 words. Other devices, including both E825-C and E830 devices have different sizes for their CSS header. The use of a hard coded value results in the driver reading from the wrong block in the NVM when attempting to access the Shadow RAM copy. This results in the driver reporting the fw.bundle as 0x0 in both the devlink dev info and ethtool -i output. The first E830 support was introduced by commit ba20ecb1d1bb ("ice: Hook up 4 E830 devices by adding their IDs") and the first E825-C support was introducted by commit f64e18944233 ("ice: introduce new E825C devices family") The NVM actually contains the CSS header length embedded in it. Remove the hard coded value and replace it with logic to read the length from the NVM directly. This is more resilient against all existing and future hardware, vs looking up the expected values from a table. It ensures the driver will read from the appropriate place when determining the ETRACK ID value used for populating the fw.bundle_id and for reporting in ethtool -i. The CSS header length for both the active and inactive flash bank is stored in the ice_bank_info structure to avoid unnecessary duplicate work when accessing multiple words of the Shadow RAM. Both banks are read in the unlikely event that the header length is different for the NVM in the inactive bank, rather than being different only by the overall device family. Fixes: ba20ecb1d1bb ("ice: Hook up 4 E830 devices by adding their IDs") Co-developed-by: Paul Greenwalt <paul.greenwalt@intel.com> Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-2-e3563aa89b0c@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-05ice: fix iteration of TLVs in Preserved Fields AreaJacob Keller
The ice_get_pfa_module_tlv() function iterates over the Type-Length-Value structures in the Preserved Fields Area (PFA) of the NVM. This is used by the driver to access data such as the Part Board Assembly identifier. The function uses simple logic to iterate over the PFA. First, the pointer to the PFA in the NVM is read. Then the total length of the PFA is read from the first word. A pointer to the first TLV is initialized, and a simple loop iterates over each TLV. The pointer is moved forward through the NVM until it exceeds the PFA area. The logic seems sound, but it is missing a key detail. The Preserved Fields Area length includes one additional final word. This is documented in the device data sheet as a dummy word which contains 0xFFFF. All NVMs have this extra word. If the driver tries to scan for a TLV that is not in the PFA, it will read past the size of the PFA. It reads and interprets the last dummy word of the PFA as a TLV with type 0xFFFF. It then reads the word following the PFA as a length. The PFA resides within the Shadow RAM portion of the NVM, which is relatively small. All of its offsets are within a 16-bit size. The PFA pointer and TLV pointer are stored by the driver as 16-bit values. In almost all cases, the word following the PFA will be such that interpreting it as a length will result in 16-bit arithmetic overflow. Once overflowed, the new next_tlv value is now below the maximum offset of the PFA. Thus, the driver will continue to iterate the data as TLVs. In the worst case, the driver hits on a sequence of reads which loop back to reading the same offsets in an endless loop. To fix this, we need to correct the loop iteration check to account for this extra word at the end of the PFA. This alone is sufficient to resolve the known cases of this issue in the field. However, it is plausible that an NVM could be misconfigured or have corrupt data which results in the same kind of overflow. Protect against this by using check_add_overflow when calculating both the maximum offset of the TLVs, and when calculating the next_tlv offset at the end of each loop iteration. This ensures that the driver will not get stuck in an infinite loop when scanning the PFA. Fixes: e961b679fb0b ("ice: add board identifier info to devlink .info_get") Co-developed-by: Paul Greenwalt <paul.greenwalt@intel.com> Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-1-e3563aa89b0c@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-29ice: check for unregistering correct number of devlink paramsDave Ertman
On module load, the ice driver checks for the lack of a specific PF capability to determine if it should reduce the number of devlink params to register. One situation when this test returns true is when the driver loads in safe mode. The same check is not present on the unload path when devlink params are unregistered. This results in the driver triggering a WARN_ON in the kernel devlink code. The current check and code path uses a reduction in the number of elements reported in the list of params. This is fragile and not good for future maintaining. Change the parameters to be held in two lists, one always registered and one dependent on the check. Add a symmetrical check in the unload path so that the correct parameters are unregistered as well. Fixes: 109eb2917284 ("ice: Add tx_scheduling_layers devlink param") CC: Lukasz Czapnik <lukasz.czapnik@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-8-dc8593d2bbc6@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-29ice: fix 200G PHY types to link speed mappingPaul Greenwalt
Commit 24407a01e57c ("ice: Add 200G speed/phy type use") added support for 200G PHY speeds, but did not include the mapping of 200G PHY types to link speed. As a result the driver is returning UNKNOWN link speed when setting 200G ethtool advertised link modes. To fix this add 200G PHY types to link speed mapping to ice_get_link_speed_based_on_phy_type(). Fixes: 24407a01e57c ("ice: Add 200G speed/phy type use") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-5-dc8593d2bbc6@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-29i40e: Fully suspend and resume IO operations in EEH caseThinh Tran
When EEH events occurs, the callback functions in the i40e, which are managed by the EEH driver, will completely suspend and resume all IO operations. - In the PCI error detected callback, replaced i40e_prep_for_reset() with i40e_io_suspend(). The change is to fully suspend all I/O operations - In the PCI error slot reset callback, replaced pci_enable_device_mem() with pci_enable_device(). This change enables both I/O and memory of the device. - In the PCI error resume callback, replaced i40e_handle_reset_warning() with i40e_io_resume(). This change allows the system to resume I/O operations Fixes: a5f3d2c17b07 ("powerpc/pseries/pci: Add MSI domains") Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Robert Thomas <rob.thomas@ibm.com> Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-3-dc8593d2bbc6@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-29i40e: factoring out i40e_suspend/i40e_resumeThinh Tran
Two new functions, i40e_io_suspend() and i40e_io_resume(), have been introduced. These functions were factored out from the existing i40e_suspend() and i40e_resume() respectively. This factoring was done due to concerns about the logic of the I40E_SUSPENSED state, which caused the device to be unable to recover. The functions are now used in the EEH handling for device suspend/resume callbacks. The function i40e_enable_mc_magic_wake() has been moved ahead of i40e_io_suspend() to ensure it is declared before being used. Tested-by: Robert Thomas <rob.thomas@ibm.com> Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-2-dc8593d2bbc6@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-29e1000e: move force SMBUS near the end of enable_ulp functionHui Wang
The commit 861e8086029e ("e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue") introduces a regression on PCH_MTP_I219_LM18 (PCIID: 0x8086550A). Without the referred commit, the ethernet works well after suspend and resume, but after applying the commit, the ethernet couldn't work anymore after the resume and the dmesg shows that the NIC link changes to 10Mbps (1000Mbps originally): [ 43.305084] e1000e 0000:00:1f.6 enp0s31f6: NIC Link is Up 10 Mbps Full Duplex, Flow Control: Rx/Tx Without the commit, the force SMBUS code will not be executed if "return 0" or "goto out" is executed in the enable_ulp(), and in my case, the "goto out" is executed since FWSM_FW_VALID is set. But after applying the commit, the force SMBUS code will be ran unconditionally. Here move the force SMBUS code back to enable_ulp() and put it immediately ahead of hw->phy.ops.release(hw), this could allow the longest settling time as possible for interface in this function and doesn't change the original code logic. The issue was found on a Lenovo laptop with the ethernet hw as below: 00:1f.6 Ethernet controller [0200]: Intel Corporation Device [8086:550a] (rev 20). And this patch is verified (cable plug and unplug, system suspend and resume) on Lenovo laptops with ethernet hw: [8086:550a], [8086:550b], [8086:15bb], [8086:15be], [8086:1a1f], [8086:1a1c] and [8086:0dc7]. Fixes: 861e8086029e ("e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue") Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-1-dc8593d2bbc6@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-27ice: fix accounting if a VLAN already existsJacob Keller
The ice_vsi_add_vlan() function is used to add a VLAN filter for the target VSI. This function prepares a filter in the switch table for the given VSI. If it succeeds, the vsi->num_vlan counter is incremented. It is not considered an error to add a VLAN which already exists in the switch table, so the function explicitly checks and ignores -EEXIST. The vsi->num_vlan counter is still incremented. This seems incorrect, as it means we can double-count in the case where the same VLAN is added twice by the caller. The actual table will have one less filter than the count. The ice_vsi_del_vlan() function similarly checks and handles the -ENOENT condition for when deleting a filter that doesn't exist. This flow only decrements the vsi->num_vlan if it actually deleted a filter. The vsi->num_vlan counter is used only in a few places, primarily related to tracking the number of non-zero VLANs. If the vsi->num_vlans gets out of sync, then ice_vsi_num_non_zero_vlans() will incorrectly report more VLANs than are present, and ice_vsi_has_non_zero_vlans() could return true potentially in cases where there are only VLAN 0 filters left. Fix this by only incrementing the vsi->num_vlan in the case where we actually added an entry, and not in the case where the entry already existed. Fixes: a1ffafb0b4a4 ("ice: Support configuring the device to Double VLAN Mode") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240523-net-2024-05-23-intel-net-fixes-v1-2-17a923e0bb5f@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-27idpf: don't enable NAPI and interrupts prior to allocating Rx buffersAlexander Lobakin
Currently, idpf enables NAPI and interrupts prior to allocating Rx buffers. This may lead to frame loss (there are no buffers to place incoming frames) and even crashes on quick ifup-ifdown. Interrupts must be enabled only after all the resources are here and available. Split interrupt init into two phases: initialization and enabling, and perform the second only after the queues are fully initialized. Note that we can't just move interrupt initialization down the init process, as the queues must have correct a ::q_vector pointer set and NAPI already added in order to allocate buffers correctly. Also, during the deinit process, disable HW interrupts first and only then disable NAPI. Otherwise, there can be a HW event leading to napi_schedule(), but the NAPI will already be unavailable. Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport") Reported-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240523-net-2024-05-23-intel-net-fixes-v1-1-17a923e0bb5f@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-23Merge tag 'net-6.10-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Paolo Abeni: "Quite smaller than usual. Notably it includes the fix for the unix regression from the past weeks. The TCP window fix will require some follow-up, already queued. Current release - regressions: - af_unix: fix garbage collection of embryos Previous releases - regressions: - af_unix: fix race between GC and receive path - ipv6: sr: fix missing sk_buff release in seg6_input_core - tcp: remove 64 KByte limit for initial tp->rcv_wnd value - eth: r8169: fix rx hangup - eth: lan966x: remove ptp traps in case the ptp is not enabled - eth: ixgbe: fix link breakage vs cisco switches - eth: ice: prevent ethtool from corrupting the channels Previous releases - always broken: - openvswitch: set the skbuff pkt_type for proper pmtud support - tcp: Fix shift-out-of-bounds in dctcp_update_alpha() Misc: - a bunch of selftests stabilization patches" * tag 'net-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (25 commits) r8169: Fix possible ring buffer corruption on fragmented Tx packets. idpf: Interpret .set_channels() input differently ice: Interpret .set_channels() input differently nfc: nci: Fix handling of zero-length payload packets in nci_rx_work() net: relax socket state check at accept time. tcp: remove 64 KByte limit for initial tp->rcv_wnd value net: ti: icssg_prueth: Fix NULL pointer dereference in prueth_probe() tls: fix missing memory barrier in tls_init net: fec: avoid lock evasion when reading pps_enable Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI" testing: net-drv: use stats64 for testing net: mana: Fix the extra HZ in mana_hwc_send_request net: lan966x: Remove ptp traps in case the ptp is not enabled. openvswitch: Set the skbuff pkt_type for proper pmtud support. selftest: af_unix: Make SCM_RIGHTS into OOB data. af_unix: Fix garbage collection of embryos carrying OOB with SCM_RIGHTS tcp: Fix shift-out-of-bounds in dctcp_update_alpha(). selftests/net: use tc rule to filter the na packet ipv6: sr: fix memleak in seg6_hmac_init_algo af_unix: Update unix_sk(sk)->oob_skb under sk_receive_queue lock. ...
2024-05-23idpf: Interpret .set_channels() input differentlyLarysa Zaremba
Unlike ice, idpf does not check, if user has requested at least 1 combined channel. Instead, it relies on a check in the core code. Unfortunately, the check does not trigger for us because of the hacky .set_channels() interpretation logic that is not consistent with the core code. This naturally leads to user being able to trigger a crash with an invalid input. This is how: 1. ethtool -l <IFNAME> -> combined: 40 2. ethtool -L <IFNAME> rx 0 tx 0 combined number is not specified, so command becomes {rx_count = 0, tx_count = 0, combined_count = 40}. 3. ethnl_set_channels checks, if there is at least 1 RX and 1 TX channel, comparing (combined_count + rx_count) and (combined_count + tx_count) to zero. Obviously, (40 + 0) is greater than zero, so the core code deems the input OK. 4. idpf interprets `rx 0 tx 0` as 0 channels and tries to proceed with such configuration. The issue has to be solved fundamentally, as current logic is also known to cause AF_XDP problems in ice [0]. Interpret the command in a way that is more consistent with ethtool manual [1] (--show-channels and --set-channels) and new ice logic. Considering that in the idpf driver only the difference between RX and TX queues forms dedicated channels, change the correct way to set number of channels to: ethtool -L <IFNAME> combined 10 /* For symmetric queues */ ethtool -L <IFNAME> combined 8 tx 2 rx 0 /* For asymmetric queues */ [0] https://lore.kernel.org/netdev/20240418095857.2827-1-larysa.zaremba@intel.com/ [1] https://man7.org/linux/man-pages/man8/ethtool.8.html Fixes: 02cbfba1add5 ("idpf: add ethtool callbacks") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-05-23ice: Interpret .set_channels() input differentlyLarysa Zaremba
A bug occurs because a safety check guarding AF_XDP-related queues in ethnl_set_channels(), does not trigger. This happens, because kernel and ice driver interpret the ethtool command differently. How the bug occurs: 1. ethtool -l <IFNAME> -> combined: 40 2. Attach AF_XDP to queue 30 3. ethtool -L <IFNAME> rx 15 tx 15 combined number is not specified, so command becomes {rx_count = 15, tx_count = 15, combined_count = 40}. 4. ethnl_set_channels checks, if there are any AF_XDP of queues from the new (combined_count + rx_count) to the old one, so from 55 to 40, check does not trigger. 5. ice interprets `rx 15 tx 15` as 15 combined channels and deletes the queue that AF_XDP is attached to. Interpret the command in a way that is more consistent with ethtool manual [0] (--show-channels and --set-channels). Considering that in the ice driver only the difference between RX and TX queues forms dedicated channels, change the correct way to set number of channels to: ethtool -L <IFNAME> combined 10 /* For symmetric queues */ ethtool -L <IFNAME> combined 8 tx 2 rx 0 /* For asymmetric queues */ [0] https://man7.org/linux/man-pages/man8/ethtool.8.html Fixes: 87324e747fde ("ice: Implement ethtool ops for channels") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-05-23Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"Jacob Keller
This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d. According to the commit, it implements a manual AN-37 for some "troublesome" Juniper MX5 switches. This appears to be a workaround for a particular switch. It has been reported that this causes a severe breakage for other switches, including a Cisco 3560CX-12PD-S. The code appears to be a workaround for a specific switch which fails to link in SFI mode. It expects to see AN-37 auto negotiation in order to link. The Cisco switch is not expecting AN-37 auto negotiation. When the device starts the manual AN-37, the Cisco switch decides that the port is confused and stops attempting to link with it. This persists until a power cycle. A simple driver unload and reload does not resolve the issue, even if loading with a version of the driver which lacks this workaround. The authors of the workaround commit have not responded with clarifications, and the result of the workaround is complete failure to connect with other switches. This appears to be a case where the driver can either "correctly" link with the Juniper MX5 switch, at the cost of bricking the link with the Cisco switch, or it can behave properly for the Cisco switch, but fail to link with the Junipir MX5 switch. I do not know enough about the standards involved to clearly determine whether either switch is at fault or behaving incorrectly. Nor do I know whether there exists some alternative fix which corrects behavior with both switches. Revert the workaround for the Juniper switch. Fixes: 565736048bd5 ("ixgbe: Manual AN-37 for troublesome link partners for X550 SFI") Link: https://lore.kernel.org/netdev/cbe874db-9ac9-42b8-afa0-88ea910e1e99@intel.com/T/ Link: https://forum.proxmox.com/threads/intel-x553-sfp-ixgbe-no-go-on-pve8.135129/#post-612291 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Cc: Jeff Daly <jeffd@silicom-usa.com> Cc: kernel.org-fo5k2w@ycharbi.fr Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240520-net-2024-05-20-revert-silicom-switch-workaround-v1-1-50f80f261c94@intel.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-05-22tracing/treewide: Remove second parameter of __assign_str()Steven Rostedt (Google)
With the rework of how the __string() handles dynamic strings where it saves off the source string in field in the helper structure[1], the assignment of that value to the trace event field is stored in the helper value and does not need to be passed in again. This means that with: __string(field, mystring) Which use to be assigned with __assign_str(field, mystring), no longer needs the second parameter and it is unused. With this, __assign_str() will now only get a single parameter. There's over 700 users of __assign_str() and because coccinelle does not handle the TRACE_EVENT() macro I ended up using the following sed script: git grep -l __assign_str | while read a ; do sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file; mv /tmp/test-file $a; done I then searched for __assign_str() that did not end with ';' as those were multi line assignments that the sed script above would fail to catch. Note, the same updates will need to be done for: __assign_str_len() __assign_rel_str() __assign_rel_str_len() I tested this with both an allmodconfig and an allyesconfig (build only for both). [1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/ Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts. Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs Tested-by: Guenter Roeck <linux@roeck-us.net>
2024-05-20Merge tag 'dma-mapping-6.10-2024-05-20' of ↵Linus Torvalds
git://git.infradead.org/users/hch/dma-mapping Pull dma-mapping updates from Christoph Hellwig: - optimize DMA sync calls when they are no-ops (Alexander Lobakin) - fix swiotlb padding for untrusted devices (Michael Kelley) - add documentation for swiotb (Michael Kelley) * tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping: dma: fix DMA sync for drivers not calling dma_set_mask*() xsk: use generic DMA sync shortcut instead of a custom one page_pool: check for DMA sync shortcut earlier page_pool: don't use driver-set flags field directly page_pool: make sure frag API fields don't span between cachelines iommu/dma: avoid expensive indirect calls for sync operations dma: avoid redundant calls for sync operations dma: compile-out DMA sync op calls when not used iommu/dma: fix zeroing of bounce buffer padding used by untrusted devices swiotlb: remove alloc_size argument to swiotlb_tbl_map_single() Documentation/core-api: add swiotlb documentation
2024-05-16idpf: don't skip over ethtool tcp-data-split settingMichal Schmidt
Disabling tcp-data-split on idpf silently fails: # ethtool -G $NETDEV tcp-data-split off # ethtool -g $NETDEV | grep 'TCP data split' TCP data split: on But it works if you also change 'tx' or 'rx': # ethtool -G $NETDEV tcp-data-split off tx 256 # ethtool -g $NETDEV | grep 'TCP data split' TCP data split: off The bug is in idpf_set_ringparam, where it takes a shortcut out if the TX and RX sizes are not changing. Fix it by checking also if the tcp-data-split setting remains unchanged. Only then can the soft reset be skipped. Fixes: 9b1aa3ef2328 ("idpf: add get/set for Ethtool's header split ringparam") Reported-by: Xu Du <xudu@redhat.com> Closes: https://issues.redhat.com/browse/RHEL-36182 Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Link: https://lore.kernel.org/r/20240515092414.158079-1-mschmidt@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-14Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Merge in late fixes to prepare for the 6.10 net-next PR. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-10ice: Fix package download algorithmDan Nowlin
Previously, the driver assumed that all signature segments would contain one or more buffers to download. In the future, there will be signature segments that will contain no buffers to download. Correct download flow to allow for signature segments that have zero download buffers and skip the download in this case. Fixes: 3cbdb0343022 ("ice: Add support for E830 DDP package segment") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Dan Nowlin <dan.nowlin@intel.com> Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240508171908.2760776-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-08net: e1000e & ixgbe: Remove PCI_HEADER_TYPE_MFD duplicatesIlpo Järvinen
PCI_HEADER_TYPE_MULTIFUNC is define by e1000e and ixgbe and both are unused. There is already PCI_HEADER_TYPE_MFD in pci_regs.h anyway which should be used instead so remove the duplicated defines of it. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Hariprasad Kelam <hkelam@marvell.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-08igc: fix a log entry using uninitialized netdevCorinna Vinschen
During successful probe, igc logs this: [ 5.133667] igc 0000:01:00.0 (unnamed net_device) (uninitialized): PHC added ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ The reason is that igc_ptp_init() is called very early, even before register_netdev() has been called. So the netdev_info() call works on a partially uninitialized netdev. Fix this by calling igc_ptp_init() after register_netdev(), right after the media autosense check, just as in igb. Add a comment, just as in igb. Now the log message is fine: [ 5.200987] igc 0000:01:00.0 eth0: PHC added Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Reviewed-by: Hariprasad Kelam <hkelam@marvell.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-08ice: remove correct filters during eswitch releaseMichal Swiatkowski
ice_clear_dflt_vsi() is only removing default rule. Both default RX and TX rule should be removed during release. If it isn't switching to switchdev, second time results in error, because TX filter is already there. Fix it by removing the correct set of rules. Fixes: 50d62022f455 ("ice: default Tx rule instead of to queue") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-08igb: flower: validate control flagsAsbjørn Sloth Tønnesen
This driver currently doesn't support any control flags. Use flow_rule_match_has_control_flags() to check for control flags, such as can be set through `tc flower ... ip_flags frag`. In case any control flags are masked, flow_rule_match_has_control_flags() sets a NL extended error message, and we return -EOPNOTSUPP. Only compile-tested. Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-08ice: flower: validate control flagsAsbjørn Sloth Tønnesen
This driver currently doesn't support any control flags. Use flow_rule_has_control_flags() to check for control flags, such as can be set through `tc flower ... ip_flags frag`. In case any control flags are masked, flow_rule_has_control_flags() sets a NL extended error message, and we return -EOPNOTSUPP. Only compile-tested. Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-08iavf: flower: validate control flagsAsbjørn Sloth Tønnesen
This driver currently doesn't support any control flags. Use flow_rule_has_control_flags() to check for control flags, such as can be set through `tc flower ... ip_flags frag`. In case any control flags are masked, flow_rule_has_control_flags() sets a NL extended error message, and we return -EOPNOTSUPP. Only compile-tested. Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-08i40e: flower: validate control flagsAsbjørn Sloth Tønnesen
This driver currently doesn't support any control flags. Use flow_rule_has_control_flags() to check for control flags, such as can be set through `tc flower ... ip_flags frag`. In case any control flags are masked, flow_rule_has_control_flags() sets a NL extended error message, and we return -EOPNOTSUPP. Only compile-tested. Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-08xsk: use generic DMA sync shortcut instead of a custom oneAlexander Lobakin
XSk infra's been using its own DMA sync shortcut to try avoiding redundant function calls. Now that there is a generic one, remove the custom implementation and rely on the generic helpers. xsk_buff_dma_sync_for_cpu() doesn't need the second argument anymore, remove it. Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2024-05-07Merge branch '100GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-05-06 (ice) This series contains updates to ice driver only. Paul adds support for additional E830 devices and adjusts naming for existing E830 devices. Marcin commonizes a couple of TC setup calls to reduce duplicated code. Mateusz adds ice_vsi_cfg_params into ice_vsi to consolidate info. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: ice: refactor struct ice_vsi_cfg_params to be inside of struct ice_vsi ice: Deduplicate tc action setup ice: update E830 device ids and comments ice: add additional E830 device ids ==================== Link: https://lore.kernel.org/r/20240506170827.948682-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-07net: annotate writes on dev->mtu from ndo_change_mtu()Eric Dumazet
Simon reported that ndo_change_mtu() methods were never updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted in commit 501a90c94510 ("inet: protect against too small mtu values.") We read dev->mtu without holding RTNL in many places, with READ_ONCE() annotations. It is time to take care of ndo_change_mtu() methods to use corresponding WRITE_ONCE() Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Simon Horman <horms@kernel.org> Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/ Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Shannon Nelson <shannon.nelson@amd.com> Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-05-06ice: refactor struct ice_vsi_cfg_params to be inside of struct ice_vsiMateusz Polchlopek
Refactor struct ice_vsi_cfg_params to be embedded into struct ice_vsi. Prior to that the members of the struct were scattered around ice_vsi, and were copy-pasted for purposes of reinit. Now we have struct handy, and it is easier to have something sticky in the flags field. Suggested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Vaishnavi Tipireddy <vaishnavi.tipireddy@intel.com> Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-06ice: Deduplicate tc action setupMarcin Szycik
ice_tc_setup_redirect_action() and ice_tc_setup_mirror_action() are almost identical, except for setting filter action. Reduce them to one function with an extra param, which handles both cases. Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-06ice: update E830 device ids and commentsPaul Greenwalt
Update existing E830 device ids and comments to align with new naming 'C' for 100G and 'CC' for 200G. Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-05-06ice: add additional E830 device idsPaul Greenwalt
Add support for additional E830 device ids which are supported by the driver: - 0x12D5: Intel(R) Ethernet Controller E830-C for backplane - 0x12D8: Intel(R) Ethernet Controller E830-C for QSFP - 0x12DA: Intel(R) Ethernet Controller E830-C for SFP - 0x12DC: Intel(R) Ethernet Controller E830-XXV for backplane - 0x12DD: Intel(R) Ethernet Controller E830-XXV for QSFP - 0x12DE: Intel(R) Ethernet Controller E830-XXV for SFP Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
generated by cgit v1.2.3-70-g09d2 (git 2.48.1) at 2025-03-21 18:43:34 +0000