summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel
AgeCommit message (Collapse)Author
2024-09-09igb: Always call igb_xdp_ring_update_tail() under Tx lockSriram Yagnaraman
Always call igb_xdp_ring_update_tail() under __netif_tx_lock, add a comment and lockdep assert to indicate that. This is needed to share the same TX ring between XDP, XSK and slow paths. Furthermore, the current XDP implementation is racy on tail updates. Fixes: 9cbc948b5a20 ("igb: add XDP support") Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech> [Kurt: Add lockdep assert and fixes tag] Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09ice: fix VSI lists confusion when adding VLANsMichal Schmidt
The description of function ice_find_vsi_list_entry says: Search VSI list map with VSI count 1 However, since the blamed commit (see Fixes below), the function no longer checks vsi_count. This causes a problem in ice_add_vlan_internal, where the decision to share VSI lists between filter rules relies on the vsi_count of the found existing VSI list being 1. The reproducing steps: 1. Have a PF and two VFs. There will be a filter rule for VLAN 0, referring to a VSI list containing VSIs: 0 (PF), 2 (VF#0), 3 (VF#1). 2. Add VLAN 1234 to VF#0. ice will make the wrong decision to share the VSI list with the new rule. The wrong behavior may not be immediately apparent, but it can be observed with debug prints. 3. Add VLAN 1234 to VF#1. ice will unshare the VSI list for the VLAN 1234 rule. Due to the earlier bad decision, the newly created VSI list will contain VSIs 0 (PF) and 3 (VF#1), instead of expected 2 (VF#0) and 3 (VF#1). 4. Try pinging a network peer over the VLAN interface on VF#0. This fails. Reproducer script at: https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/test-vlan-vsi-list-confusion.sh Commented debug trace: https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/ice-vlan-vsi-lists-debug.txt Patch adding the debug prints: https://gitlab.com/mschmidt2/linux/-/commit/f8a8814623944a45091a77c6094c40bfe726bfdb (Unsafe, by the way. Lacks rule_lock when dumping in ice_remove_vlan.) Michal Swiatkowski added to the explanation that the bug is caused by reusing a VSI list created for VLAN 0. All created VFs' VSIs are added to VLAN 0 filter. When a non-zero VLAN is created on a VF which is already in VLAN 0 (normal case), the VSI list from VLAN 0 is reused. It leads to a problem because all VFs (VSIs to be specific) that are subscribed to VLAN 0 will now receive a new VLAN tag traffic. This is one bug, another is the bug described above. Removing filters from one VF will remove VLAN filter from the previous VF. It happens a VF is reset. Example: - creation of 3 VFs - we have VSI list (used for VLAN 0) [0 (pf), 2 (vf1), 3 (vf2), 4 (vf3)] - we are adding VLAN 100 on VF1, we are reusing the previous list because 2 is there - VLAN traffic works fine, but VLAN 100 tagged traffic can be received on all VSIs from the list (for example broadcast or unicast) - trust is turning on VF2, VF2 is resetting, all filters from VF2 are removed; the VLAN 100 filter is also removed because 3 is on the list - VLAN traffic to VF1 isn't working anymore, there is a need to recreate VLAN interface to readd VLAN filter One thing I'm not certain about is the implications for the LAG feature, which is another caller of ice_find_vsi_list_entry. I don't have a LAG-capable card at hand to test. Fixes: 23ccae5ce15f ("ice: changes to the interface with the HW and FW for SRIOV_VF+LAG") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Dave Ertman <David.m.ertman@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09ice: stop calling pci_disable_device() as we use pcimPrzemek Kitszel
Our driver uses devres to manage resources, in particular we call pcim_enable_device(), what also means we express the intent to get automatic pci_disable_device() call at driver removal. Manual calls to pci_disable_device() misuse the API. Recent commit (see "Fixes" tag) has changed the removal action from conditional (silent ignore of double call to pci_disable_device()) to unconditional, but able to catch unwanted redundant calls; see cited "Fixes" commit for details. Since that, unloading the driver yields following warn+splat: [70633.628490] ice 0000:af:00.7: disabling already-disabled device [70633.628512] WARNING: CPU: 52 PID: 33890 at drivers/pci/pci.c:2250 pci_disable_device+0xf4/0x100 ... [70633.628744] ? pci_disable_device+0xf4/0x100 [70633.628752] release_nodes+0x4a/0x70 [70633.628759] devres_release_all+0x8b/0xc0 [70633.628768] device_unbind_cleanup+0xe/0x70 [70633.628774] device_release_driver_internal+0x208/0x250 [70633.628781] driver_detach+0x47/0x90 [70633.628786] bus_remove_driver+0x80/0x100 [70633.628791] pci_unregister_driver+0x2a/0xb0 [70633.628799] ice_module_exit+0x11/0x3a [ice] Note that this is the only Intel ethernet driver that needs such fix. Fixes: f748a07a0b64 ("PCI: Remove legacy pcim_release()") Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Philipp Stanner <pstanner@redhat.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09ice: fix accounting for filters shared by multiple VSIsJacob Keller
When adding a switch filter (such as a MAC or VLAN filter), it is expected that the driver will detect the case where the filter already exists, and return -EEXIST. This is used by calling code such as ice_vc_add_mac_addr, and ice_vsi_add_vlan to avoid incrementing the accounting fields such as vsi->num_vlan or vf->num_mac. This logic works correctly for the case where only a single VSI has added a given switch filter. When a second VSI adds the same switch filter, the driver converts the existing filter from an ICE_FWD_TO_VSI filter into an ICE_FWD_TO_VSI_LIST filter. This saves switch resources, by ensuring that multiple VSIs can re-use the same filter. The ice_add_update_vsi_list() function is responsible for doing this conversion. When first converting a filter from the FWD_TO_VSI into FWD_TO_VSI_LIST, it checks if the VSI being added is the same as the existing rule's VSI. In such a case it returns -EEXIST. However, when the switch rule has already been converted to a FWD_TO_VSI_LIST, the logic is different. Adding a new VSI in this case just requires extending the VSI list entry. The logic for checking if the rule already exists in this case returns 0 instead of -EEXIST. This breaks the accounting logic mentioned above, so the counters for how many MAC and VLAN filters exist for a given VF or VSI no longer accurately reflect the actual count. This breaks other code which relies on these counts. In typical usage this primarily affects such filters generally shared by multiple VSIs such as VLAN 0, or broadcast and multicast MAC addresses. Fix this by correctly reporting -EEXIST in the case of adding the same VSI to a switch rule already converted to ICE_FWD_TO_VSI_LIST. Fixes: 9daf8208dd4d ("ice: Add support for switch filter programming") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09ice: Fix lldp packets dropping after changing the number of channelsMartyna Szapar-Mudlaw
After vsi setup refactor commit 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") ice_cfg_sw_lldp function which removes rx rule directing LLDP packets to vsi is moved from ice_vsi_release to ice_vsi_decfg function. ice_vsi_decfg is used in more cases than just in vsi_release resulting in unnecessary removal of rx lldp packets handling switch rule. This leads to lldp packets being dropped after a change number of channels via ethtool. This patch moves ice_cfg_sw_lldp function that removes rx lldp sw rule back to ice_vsi_release function. Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Reported-by: Matěj Grégr <mgregr@netx.as> Closes: https://lore.kernel.org/intel-wired-lan/1be45a76-90af-4813-824f-8398b69745a9@netx.as/T/#u Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-03ice: do not bring the VSI up, if it was down before the XDP setupLarysa Zaremba
After XDP configuration is completed, we bring the interface up unconditionally, regardless of its state before the call to .ndo_bpf(). Preserve the information whether the interface had to be brought down and later bring it up only in such case. Fixes: efc2214b6047 ("ice: Add support for XDP") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-03ice: remove ICE_CFG_BUSY locking from AF_XDP codeLarysa Zaremba
Locking used in ice_qp_ena() and ice_qp_dis() does pretty much nothing, because ICE_CFG_BUSY is a state flag that is supposed to be set in a PF state, not VSI one. Therefore it does not protect the queue pair from e.g. reset. Remove ICE_CFG_BUSY locking from ice_qp_dis() and ice_qp_ena(). Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-03ice: check ICE_VSI_DOWN under rtnl_lock when preparing for resetLarysa Zaremba
Consider the following scenario: .ndo_bpf() | ice_prepare_for_reset() | ________________________|_______________________________________| rtnl_lock() | | ice_down() | | | test_bit(ICE_VSI_DOWN) - true | | ice_dis_vsi() returns | ice_up() | | | proceeds to rebuild a running VSI | .ndo_bpf() is not the only rtnl-locked callback that toggles the interface to apply new configuration. Another example is .set_channels(). To avoid the race condition above, act only after reading ICE_VSI_DOWN under rtnl_lock. Fixes: 0f9d5027a749 ("ice: Refactor VSI allocation, deletion and rebuild flow") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-03ice: check for XDP rings instead of bpf program when unconfiguringLarysa Zaremba
If VSI rebuild is pending, .ndo_bpf() can attach/detach the XDP program on VSI without applying new ring configuration. When unconfiguring the VSI, we can encounter the state in which there is an XDP program but no XDP rings to destroy or there will be XDP rings that need to be destroyed, but no XDP program to indicate their presence. When unconfiguring, rely on the presence of XDP rings rather then XDP program, as they better represent the current state that has to be destroyed. Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-03ice: protect XDP configuration with a mutexLarysa Zaremba
The main threat to data consistency in ice_xdp() is a possible asynchronous PF reset. It can be triggered by a user or by TX timeout handler. XDP setup and PF reset code access the same resources in the following sections: * ice_vsi_close() in ice_prepare_for_reset() - already rtnl-locked * ice_vsi_rebuild() for the PF VSI - not protected * ice_vsi_open() - already rtnl-locked With an unfortunate timing, such accesses can result in a crash such as the one below: [ +1.999878] ice 0000:b1:00.0: Registered XDP mem model MEM_TYPE_XSK_BUFF_POOL on Rx ring 14 [ +2.002992] ice 0000:b1:00.0: Registered XDP mem model MEM_TYPE_XSK_BUFF_POOL on Rx ring 18 [Mar15 18:17] ice 0000:b1:00.0 ens801f0np0: NETDEV WATCHDOG: CPU: 38: transmit queue 14 timed out 80692736 ms [ +0.000093] ice 0000:b1:00.0 ens801f0np0: tx_timeout: VSI_num: 6, Q 14, NTC: 0x0, HW_HEAD: 0x0, NTU: 0x0, INT: 0x4000001 [ +0.000012] ice 0000:b1:00.0 ens801f0np0: tx_timeout recovery level 1, txqueue 14 [ +0.394718] ice 0000:b1:00.0: PTP reset successful [ +0.006184] BUG: kernel NULL pointer dereference, address: 0000000000000098 [ +0.000045] #PF: supervisor read access in kernel mode [ +0.000023] #PF: error_code(0x0000) - not-present page [ +0.000023] PGD 0 P4D 0 [ +0.000018] Oops: 0000 [#1] PREEMPT SMP NOPTI [ +0.000023] CPU: 38 PID: 7540 Comm: kworker/38:1 Not tainted 6.8.0-rc7 #1 [ +0.000031] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0014.082620210524 08/26/2021 [ +0.000036] Workqueue: ice ice_service_task [ice] [ +0.000183] RIP: 0010:ice_clean_tx_ring+0xa/0xd0 [ice] [...] [ +0.000013] Call Trace: [ +0.000016] <TASK> [ +0.000014] ? __die+0x1f/0x70 [ +0.000029] ? page_fault_oops+0x171/0x4f0 [ +0.000029] ? schedule+0x3b/0xd0 [ +0.000027] ? exc_page_fault+0x7b/0x180 [ +0.000022] ? asm_exc_page_fault+0x22/0x30 [ +0.000031] ? ice_clean_tx_ring+0xa/0xd0 [ice] [ +0.000194] ice_free_tx_ring+0xe/0x60 [ice] [ +0.000186] ice_destroy_xdp_rings+0x157/0x310 [ice] [ +0.000151] ice_vsi_decfg+0x53/0xe0 [ice] [ +0.000180] ice_vsi_rebuild+0x239/0x540 [ice] [ +0.000186] ice_vsi_rebuild_by_type+0x76/0x180 [ice] [ +0.000145] ice_rebuild+0x18c/0x840 [ice] [ +0.000145] ? delay_tsc+0x4a/0xc0 [ +0.000022] ? delay_tsc+0x92/0xc0 [ +0.000020] ice_do_reset+0x140/0x180 [ice] [ +0.000886] ice_service_task+0x404/0x1030 [ice] [ +0.000824] process_one_work+0x171/0x340 [ +0.000685] worker_thread+0x277/0x3a0 [ +0.000675] ? preempt_count_add+0x6a/0xa0 [ +0.000677] ? _raw_spin_lock_irqsave+0x23/0x50 [ +0.000679] ? __pfx_worker_thread+0x10/0x10 [ +0.000653] kthread+0xf0/0x120 [ +0.000635] ? __pfx_kthread+0x10/0x10 [ +0.000616] ret_from_fork+0x2d/0x50 [ +0.000612] ? __pfx_kthread+0x10/0x10 [ +0.000604] ret_from_fork_asm+0x1b/0x30 [ +0.000604] </TASK> The previous way of handling this through returning -EBUSY is not viable, particularly when destroying AF_XDP socket, because the kernel proceeds with removal anyway. There is plenty of code between those calls and there is no need to create a large critical section that covers all of them, same as there is no need to protect ice_vsi_rebuild() with rtnl_lock(). Add xdp_state_lock mutex to protect ice_vsi_rebuild() and ice_xdp(). Leaving unprotected sections in between would result in two states that have to be considered: 1. when the VSI is closed, but not yet rebuild 2. when VSI is already rebuild, but not yet open The latter case is actually already handled through !netif_running() case, we just need to adjust flag checking a little. The former one is not as trivial, because between ice_vsi_close() and ice_vsi_rebuild(), a lot of hardware interaction happens, this can make adding/deleting rings exit with an error. Luckily, VSI rebuild is pending and can apply new configuration for us in a managed fashion. Therefore, add an additional VSI state flag ICE_VSI_REBUILD_PENDING to indicate that ice_xdp() can just hot-swap the program. Also, as ice_vsi_rebuild() flow is touched in this patch, make it more consistent by deconfiguring VSI when coalesce allocation fails. Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Fixes: efc2214b6047 ("ice: Add support for XDP") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-03ice: move netif_queue_set_napi to rtnl-protected sectionsLarysa Zaremba
Currently, netif_queue_set_napi() is called from ice_vsi_rebuild() that is not rtnl-locked when called from the reset. This creates the need to take the rtnl_lock just for a single function and complicates the synchronization with .ndo_bpf. At the same time, there no actual need to fill napi-to-queue information at this exact point. Fill napi-to-queue information when opening the VSI and clear it when the VSI is being closed. Those routines are already rtnl-locked. Also, rewrite napi-to-queue assignment in a way that prevents inclusion of XDP queues, as this leads to out-of-bounds writes, such as one below. [ +0.000004] BUG: KASAN: slab-out-of-bounds in netif_queue_set_napi+0x1c2/0x1e0 [ +0.000012] Write of size 8 at addr ffff889881727c80 by task bash/7047 [ +0.000006] CPU: 24 PID: 7047 Comm: bash Not tainted 6.10.0-rc2+ #2 [ +0.000004] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0014.082620210524 08/26/2021 [ +0.000003] Call Trace: [ +0.000003] <TASK> [ +0.000002] dump_stack_lvl+0x60/0x80 [ +0.000007] print_report+0xce/0x630 [ +0.000007] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ +0.000007] ? __virt_addr_valid+0x1c9/0x2c0 [ +0.000005] ? netif_queue_set_napi+0x1c2/0x1e0 [ +0.000003] kasan_report+0xe9/0x120 [ +0.000004] ? netif_queue_set_napi+0x1c2/0x1e0 [ +0.000004] netif_queue_set_napi+0x1c2/0x1e0 [ +0.000005] ice_vsi_close+0x161/0x670 [ice] [ +0.000114] ice_dis_vsi+0x22f/0x270 [ice] [ +0.000095] ice_pf_dis_all_vsi.constprop.0+0xae/0x1c0 [ice] [ +0.000086] ice_prepare_for_reset+0x299/0x750 [ice] [ +0.000087] pci_dev_save_and_disable+0x82/0xd0 [ +0.000006] pci_reset_function+0x12d/0x230 [ +0.000004] reset_store+0xa0/0x100 [ +0.000006] ? __pfx_reset_store+0x10/0x10 [ +0.000002] ? __pfx_mutex_lock+0x10/0x10 [ +0.000004] ? __check_object_size+0x4c1/0x640 [ +0.000007] kernfs_fop_write_iter+0x30b/0x4a0 [ +0.000006] vfs_write+0x5d6/0xdf0 [ +0.000005] ? fd_install+0x180/0x350 [ +0.000005] ? __pfx_vfs_write+0x10/0xA10 [ +0.000004] ? do_fcntl+0x52c/0xcd0 [ +0.000004] ? kasan_save_track+0x13/0x60 [ +0.000003] ? kasan_save_free_info+0x37/0x60 [ +0.000006] ksys_write+0xfa/0x1d0 [ +0.000003] ? __pfx_ksys_write+0x10/0x10 [ +0.000002] ? __x64_sys_fcntl+0x121/0x180 [ +0.000004] ? _raw_spin_lock+0x87/0xe0 [ +0.000005] do_syscall_64+0x80/0x170 [ +0.000007] ? _raw_spin_lock+0x87/0xe0 [ +0.000004] ? __pfx__raw_spin_lock+0x10/0x10 [ +0.000003] ? file_close_fd_locked+0x167/0x230 [ +0.000005] ? syscall_exit_to_user_mode+0x7d/0x220 [ +0.000005] ? do_syscall_64+0x8c/0x170 [ +0.000004] ? do_syscall_64+0x8c/0x170 [ +0.000003] ? do_syscall_64+0x8c/0x170 [ +0.000003] ? fput+0x1a/0x2c0 [ +0.000004] ? filp_close+0x19/0x30 [ +0.000004] ? do_dup2+0x25a/0x4c0 [ +0.000004] ? __x64_sys_dup2+0x6e/0x2e0 [ +0.000002] ? syscall_exit_to_user_mode+0x7d/0x220 [ +0.000004] ? do_syscall_64+0x8c/0x170 [ +0.000003] ? __count_memcg_events+0x113/0x380 [ +0.000005] ? handle_mm_fault+0x136/0x820 [ +0.000005] ? do_user_addr_fault+0x444/0xa80 [ +0.000004] ? clear_bhb_loop+0x25/0x80 [ +0.000004] ? clear_bhb_loop+0x25/0x80 [ +0.000002] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ +0.000005] RIP: 0033:0x7f2033593154 Fixes: 080b0c8d6d26 ("ice: Fix ASSERT_RTNL() warning during certain scenarios") Fixes: 91fdbce7e8d6 ("ice: Add support in the driver for associating queue with napi") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Amritha Nambiar <amritha.nambiar@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-02igc: Unlock on error in igc_io_resume()Dan Carpenter
Call rtnl_unlock() on this error path, before returning. Fixes: bc23aa949aeb ("igc: Add pcie error handler support") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-28ice: Add netif_device_attach/detach into PF reset flowDawid Osuchowski
Ethtool callbacks can be executed while reset is in progress and try to access deleted resources, e.g. getting coalesce settings can result in a NULL pointer dereference seen below. Reproduction steps: Once the driver is fully initialized, trigger reset: # echo 1 > /sys/class/net/<interface>/device/reset when reset is in progress try to get coalesce settings using ethtool: # ethtool -c <interface> BUG: kernel NULL pointer dereference, address: 0000000000000020 PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP PTI CPU: 11 PID: 19713 Comm: ethtool Tainted: G S 6.10.0-rc7+ #7 RIP: 0010:ice_get_q_coalesce+0x2e/0xa0 [ice] RSP: 0018:ffffbab1e9bcf6a8 EFLAGS: 00010206 RAX: 000000000000000c RBX: ffff94512305b028 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff9451c3f2e588 RDI: ffff9451c3f2e588 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: ffff9451c3f2e580 R11: 000000000000001f R12: ffff945121fa9000 R13: ffffbab1e9bcf760 R14: 0000000000000013 R15: ffffffff9e65dd40 FS: 00007faee5fbe740(0000) GS:ffff94546fd80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000020 CR3: 0000000106c2e005 CR4: 00000000001706f0 Call Trace: <TASK> ice_get_coalesce+0x17/0x30 [ice] coalesce_prepare_data+0x61/0x80 ethnl_default_doit+0xde/0x340 genl_family_rcv_msg_doit+0xf2/0x150 genl_rcv_msg+0x1b3/0x2c0 netlink_rcv_skb+0x5b/0x110 genl_rcv+0x28/0x40 netlink_unicast+0x19c/0x290 netlink_sendmsg+0x222/0x490 __sys_sendto+0x1df/0x1f0 __x64_sys_sendto+0x24/0x30 do_syscall_64+0x82/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7faee60d8e27 Calling netif_device_detach() before reset makes the net core not call the driver when ethtool command is issued, the attempt to execute an ethtool command during reset will result in the following message: netlink error: No such device instead of NULL pointer dereference. Once reset is done and ice_rebuild() is executing, the netif_device_attach() is called to allow for ethtool operations to occur again in a safe manner. Fixes: fcea6f3da546 ("ice: Add stats and ethtool support") Suggested-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com> Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-28igb: Fix not clearing TimeSync interrupts for 82580Daiwei Li
82580 NICs have a hardware bug that makes it necessary to write into the TSICR (TimeSync Interrupt Cause) register to clear it: https://lore.kernel.org/all/CDCB8BE0.1EC2C%25matthew.vick@intel.com/ Add a conditional so only for 82580 we write into the TSICR register, so we don't risk losing events for other models. Without this change, when running ptp4l with an Intel 82580 card, I get the following output: > timed out while polling for tx timestamp increasing tx_timestamp_timeout or > increasing kworker priority may correct this issue, but a driver bug likely > causes it This goes away with this change. This (partially) reverts commit ee14cc9ea19b ("igb: Fix missing time sync events"). Fixes: ee14cc9ea19b ("igb: Fix missing time sync events") Closes: https://lore.kernel.org/intel-wired-lan/CAN0jFd1kO0MMtOh8N2Ztxn6f7vvDKp2h507sMryobkBKe=xk=w@mail.gmail.com/ Tested-by: Daiwei Li <daiweili@google.com> Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Daiwei Li <daiweili@google.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-21Merge branch '100GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-08-20 (ice) This series contains updates to ice driver only. Maciej fixes issues with Rx data path on architectures with PAGE_SIZE >= 8192; correcting page reuse usage and calculations for last offset and truesize. Michal corrects assignment of devlink port number to use PF id. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: use internal pf id instead of function number ice: fix truesize operations for PAGE_SIZE >= 8192 ice: fix ICE_LAST_OFFSET formula ice: fix page reuse when PAGE_SIZE is over 8k ==================== Link: https://patch.msgid.link/20240820215620.1245310-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-20igb: cope with large MAX_SKB_FRAGSPaolo Abeni
Sabrina reports that the igb driver does not cope well with large MAX_SKB_FRAG values: setting MAX_SKB_FRAG to 45 causes payload corruption on TX. An easy reproducer is to run ssh to connect to the machine. With MAX_SKB_FRAGS=17 it works, with MAX_SKB_FRAGS=45 it fails. This has been reported originally in https://bugzilla.redhat.com/show_bug.cgi?id=2265320 The root cause of the issue is that the driver does not take into account properly the (possibly large) shared info size when selecting the ring layout, and will try to fit two packets inside the same 4K page even when the 1st fraglist will trump over the 2nd head. Address the issue by checking if 2K buffers are insufficient. Fixes: 3948b05950fd ("net: introduce a config option to tweak MAX_SKB_FRAGS") Reported-by: Jan Tluka <jtluka@redhat.com> Reported-by: Jirka Hladky <jhladky@redhat.com> Reported-by: Sabrina Dubroca <sd@queasysnail.net> Tested-by: Sabrina Dubroca <sd@queasysnail.net> Tested-by: Corinna Vinschen <vinschen@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Link: https://patch.msgid.link/20240816152034.1453285-1-vinschen@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-20ice: use internal pf id instead of function numberMichal Swiatkowski
Use always the same pf id in devlink port number. When doing pass-through the PF to VM bus info func number can be any value. Fixes: 2ae0aa4758b0 ("ice: Move devlink port to PF/VF struct") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Suggested-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-20ice: fix truesize operations for PAGE_SIZE >= 8192Maciej Fijalkowski
When working on multi-buffer packet on arch that has PAGE_SIZE >= 8192, truesize is calculated and stored in xdp_buff::frame_sz per each processed Rx buffer. This means that frame_sz will contain the truesize based on last received buffer, but commit 1dc1a7e7f410 ("ice: Centrallize Rx buffer recycling") assumed this value will be constant for each buffer, which breaks the page recycling scheme and mess up the way we update the page::page_offset. To fix this, let us work on constant truesize when PAGE_SIZE >= 8192 instead of basing this on size of a packet read from Rx descriptor. This way we can simplify the code and avoid calculating truesize per each received frame and on top of that when using xdp_update_skb_shared_info(), current formula for truesize update will be valid. This means ice_rx_frame_truesize() can be removed altogether. Furthermore, first call to it within ice_clean_rx_irq() for 4k PAGE_SIZE was redundant as xdp_buff::frame_sz is initialized via xdp_init_buff() in ice_vsi_cfg_rxq(). This should have been removed at the point where xdp_buff struct started to be a member of ice_rx_ring and it was no longer a stack based variable. There are two fixes tags as my understanding is that the first one exposed us to broken truesize and page_offset handling and then second introduced broken skb_shared_info update in ice_{construct,build}_skb(). Reported-and-tested-by: Luiz Capitulino <luizcap@redhat.com> Closes: https://lore.kernel.org/netdev/8f9e2a5c-fd30-4206-9311-946a06d031bb@redhat.com/ Fixes: 1dc1a7e7f410 ("ice: Centrallize Rx buffer recycling") Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-20ice: fix ICE_LAST_OFFSET formulaMaciej Fijalkowski
For bigger PAGE_SIZE archs, ice driver works on 3k Rx buffers. Therefore, ICE_LAST_OFFSET should take into account ICE_RXBUF_3072, not ICE_RXBUF_2048. Fixes: 7237f5b0dba4 ("ice: introduce legacy Rx flag") Suggested-by: Luiz Capitulino <luizcap@redhat.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-20ice: fix page reuse when PAGE_SIZE is over 8kMaciej Fijalkowski
Architectures that have PAGE_SIZE >= 8192 such as arm64 should act the same as x86 currently, meaning reuse of a page should only take place when no one else is busy with it. Do two things independently of underlying PAGE_SIZE: - store the page count under ice_rx_buf::pgcnt - then act upon its value vs ice_rx_buf::pagecnt_bias when making the decision regarding page reuse Fixes: 2b245cb29421 ("ice: Implement transmit and NAPI support") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-11Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-qDavid S. Miller
ueue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-08-07 (igc) This series contains updates to igc driver only. Faizal adjusts the size of the MAC internal buffer on i226 devices to resolve an errata for leaking packet transmits. He also corrects a condition in which qbv_config_change_errors are incorrectly counted. Lastly, he adjusts the conditions for resetting the adapter when changing TSN Tx mode and corrects the conditions in which gtxoffset register is set. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-08Merge branch '100GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-08-07 (ice) This series contains updates to ice driver only. Grzegorz adds IRQ synchronization call before performing reset and prevents writing to hardware when it is resetting. Mateusz swaps incorrect assignment of FEC statistics. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: Fix incorrect assigns of FEC counts ice: Skip PTP HW writes during PTP reset procedure ice: Fix reset handler ==================== Link: https://patch.msgid.link/20240807224521.3819189-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-07idpf: fix UAFs when destroying the queuesAlexander Lobakin
The second tagged commit started sometimes (very rarely, but possible) throwing WARNs from net/core/page_pool.c:page_pool_disable_direct_recycling(). Turned out idpf frees interrupt vectors with embedded NAPIs *before* freeing the queues making page_pools' NAPI pointers lead to freed memory before these pools are destroyed by libeth. It's not clear whether there are other accesses to the freed vectors when destroying the queues, but anyway, we usually free queue/interrupt vectors only when the queues are destroyed and the NAPIs are guaranteed to not be referenced anywhere. Invert the allocation and freeing logic making queue/interrupt vectors be allocated first and freed last. Vectors don't require queues to be present, so this is safe. Additionally, this change allows to remove that useless queue->q_vector pointer cleanup, as vectors are still valid when freeing the queues (+ both are freed within one function, so it's not clear why nullify the pointers at all). Fixes: 1c325aac10a8 ("idpf: configure resources for TX queues") Fixes: 90912f9f4f2d ("idpf: convert header split mode to libeth + napi_build_skb()") Reported-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240806220923.3359860-4-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-07idpf: fix memleak in vport interrupt configurationMichal Kubiak
The initialization of vport interrupt consists of two functions: 1) idpf_vport_intr_init() where a generic configuration is done 2) idpf_vport_intr_req_irq() where the irq for each q_vector is requested. The first function used to create a base name for each interrupt using "kasprintf()" call. Unfortunately, although that call allocated memory for a text buffer, that memory was never released. Fix this by removing creating the interrupt base name in 1). Instead, always create a full interrupt name in the function 2), because there is no need to create a base name separately, considering that the function 2) is never called out of idpf_vport_intr_init() context. Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport") Cc: stable@vger.kernel.org # 6.7 Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240806220923.3359860-3-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-07idpf: fix memory leaks and crashes while performing a soft resetAlexander Lobakin
The second tagged commit introduced a UAF, as it removed restoring q_vector->vport pointers after reinitializating the structures. This is due to that all queue allocation functions are performed here with the new temporary vport structure and those functions rewrite the backpointers to the vport. Then, this new struct is freed and the pointers start leading to nowhere. But generally speaking, the current logic is very fragile. It claims to be more reliable when the system is low on memory, but in fact, it consumes two times more memory as at the moment of running this function, there are two vports allocated with their queues and vectors. Moreover, it claims to prevent the driver from running into "bad state", but in fact, any error during the rebuild leaves the old vport in the partially allocated state. Finally, if the interface is down when the function is called, it always allocates a new queue set, but when the user decides to enable the interface later on, vport_open() allocates them once again, IOW there's a clear memory leak here. Just don't allocate a new queue set when performing a reset, that solves crashes and memory leaks. Readd the old queue number and reopen the interface on rollback - that solves limbo states when the device is left disabled and/or without HW queues enabled. Fixes: 02cbfba1add5 ("idpf: add ethtool callbacks") Fixes: e4891e4687c8 ("idpf: split &idpf_queue into 4 strictly-typed queue structures") Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240806220923.3359860-2-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-07igc: Fix qbv tx latency by setting gtxoffsetFaizal Rahim
A large tx latency issue was discovered during testing when only QBV was enabled. The issue occurs because gtxoffset was not set when QBV is active, it was only set when launch time is active. The patch "igc: Correct the launchtime offset" only sets gtxoffset when the launchtime_enable field is set by the user. Enabling launchtime_enable ultimately sets the register IGC_TXQCTL_QUEUE_MODE_LAUNCHT (referred to as LaunchT in the SW user manual). Section 7.5.2.6 of the IGC i225/6 SW User Manual Rev 1.2.4 states: "The latency between transmission scheduling (launch time) and the time the packet is transmitted to the network is listed in Table 7-61." However, the patch misinterprets the phrase "launch time" in that section by assuming it specifically refers to the LaunchT register, whereas it actually denotes the generic term for when a packet is released from the internal buffer to the MAC transmit logic. This launch time, as per that section, also implicitly refers to the QBV gate open time, where a packet waits in the buffer for the QBV gate to open. Therefore, latency applies whenever QBV is in use. TSN features such as QBU and QAV reuse QBV, making the latency universal to TSN features. Discussed with i226 HW owner (Shalev, Avi) and we were in agreement that the term "launch time" used in Section 7.5.2.6 is not clear and can be easily misinterpreted. Avi will update this section to: "When TQAVCTRL.TRANSMIT_MODE = TSN, the latency between transmission scheduling and the time the packet is transmitted to the network is listed in Table 7-61." Fix this issue by using igc_tsn_is_tx_mode_in_tsn() as a condition to write to gtxoffset, aligning with the newly updated SW User Manual. Tested: 1. Enrol taprio on talker board base-time 0 cycle-time 1000000 flags 0x2 index 0 cmd S gatemask 0x1 interval1 index 0 cmd S gatemask 0x1 interval2 Note: interval1 = interval for a 64 bytes packet to go through interval2 = cycle-time - interval1 2. Take tcpdump on listener board 3. Use udp tai app on talker to send packets to listener 4. Check the timestamp on listener via wireshark Test Result: 100 Mbps: 113 ~193 ns 1000 Mbps: 52 ~ 84 ns 2500 Mbps: 95 ~ 223 ns Note that the test result is similar to the patch "igc: Correct the launchtime offset". Fixes: 790835fcc0cb ("igc: Correct the launchtime offset") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07igc: Fix reset adapter logics when tx mode changeFaizal Rahim
Following the "igc: Fix TX Hang issue when QBV Gate is close" changes, remaining issues with the reset adapter logic in igc_tsn_offload_apply() have been observed: 1. The reset adapter logics for i225 and i226 differ, although they should be the same according to the guidelines in I225/6 HW Design Section 7.5.2.1 on software initialization during tx mode changes. 2. The i225 resets adapter every time, even though tx mode doesn't change. This occurs solely based on the condition igc_is_device_id_i225() when calling schedule_work(). 3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only resets adapter for legacy->tsn tx mode transitions. 4. qbv_count introduced in the patch is actually not needed; in this context, a non-zero value of qbv_count is used to indicate if tx mode was unconditionally set to tsn in igc_tsn_enable_offload(). This could be replaced by checking the existing register IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit. This patch resolves all issues and enters schedule_work() to reset the adapter only when changing tx mode. It also removes reliance on qbv_count. qbv_count field will be removed in a future patch. Test ran: 1. Verify reset adapter behaviour in i225/6: a) Enrol a new GCL Reset adapter observed (tx mode change legacy->tsn) b) Enrol a new GCL without deleting qdisc No reset adapter observed (tx mode remain tsn->tsn) c) Delete qdisc Reset adapter observed (tx mode change tsn->legacy) 2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed" to confirm it remains resolved. Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07igc: Fix qbv_config_change_errors logicsFaizal Rahim
When user issues these cmds: 1. Either a) or b) a) mqprio with hardware offload disabled b) taprio with txtime-assist feature enabled 2. etf 3. tc qdisc delete 4. taprio with base time in the past At step 4, qbv_config_change_errors wrongly increased by 1. Excerpt from IEEE 802.1Q-2018 8.6.9.3.1: "If AdminBaseTime specifies a time in the past, and the current schedule is running, then: Increment ConfigChangeError counter" qbv_config_change_errors should only increase if base time is in the past and no taprio is active. In user perspective, taprio was not active when first triggered at step 4. However, i225/6 reuses qbv for etf, so qbv is enabled with a dummy schedule at step 2 where it enters igc_tsn_enable_offload() and qbv_count got incremented to 1. At step 4, it enters igc_tsn_enable_offload() again, qbv_count is incremented to 2. Because taprio is running, tc_setup_type is TC_SETUP_QDISC_ETF and qbv_count > 1, qbv_config_change_errors value got incremented. This issue happens due to reliance on qbv_count field where a non-zero value indicates that taprio is running. But qbv_count increases regardless if taprio is triggered by user or by other tsn feature. It does not align with qbv_config_change_errors expectation where it is only concerned with taprio triggered by user. Fixing this by relocating the qbv_config_change_errors logic to igc_save_qbv_schedule(), eliminating reliance on qbv_count and its inaccuracies from i225/6's multiple uses of qbv feature for other TSN features. The new function created: igc_tsn_is_taprio_activated_by_user() uses taprio_offload_enable field to indicate that the current running taprio was triggered by user, instead of triggered by non-qbv feature like etf. Fixes: ae4fe4698300 ("igc: Add qbv_config_change_errors counter") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07igc: Fix packet still tx after gate close by reducing i226 MAC retry bufferFaizal Rahim
Testing uncovered that even when the taprio gate is closed, some packets still transmit. According to i225/6 hardware errata [1], traffic might overflow the planned QBV window. This happens because MAC maintains an internal buffer, primarily for supporting half duplex retries. Therefore, even when the gate closes, residual MAC data in the buffer may still transmit. To mitigate this for i226, reduce the MAC's internal buffer from 192 bytes to the recommended 88 bytes by modifying the RETX_CTL register value. This follows guidelines from: [1] Ethernet Controller I225/I22 Spec Update Rev 2.1 Errata Item 9: TSN: Packet Transmission Might Cross Qbv Window [2] I225/6 SW User Manual Rev 1.2.4: Section 8.11.5 Retry Buffer Control Note that the RETX_CTL register can't be used in TSN mode because half duplex feature cannot coexist with TSN. Test Steps: 1. Send taprio cmd to board A: tc qdisc replace dev enp1s0 parent root handle 100 taprio \ num_tc 4 \ map 3 2 1 0 3 3 3 3 3 3 3 3 3 3 3 3 \ queues 1@0 1@1 1@2 1@3 \ base-time 0 \ sched-entry S 0x07 500000 \ sched-entry S 0x0f 500000 \ flags 0x2 \ txtime-delay 0 Note that for TC3, gate should open for 500us and close for another 500us. 3. Take tcpdump log on Board B. 4. Send udp packets via UDP tai app from Board A to Board B. 5. Analyze tcpdump log via wireshark log on Board B. Ensure that the total time from the first to the last packet received during one cycle for TC3 does not exceed 500us. Fixes: 43546211738e ("igc: Add new device ID's") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07ice: Fix incorrect assigns of FEC countsMateusz Polchlopek
Commit ac21add2540e ("ice: Implement driver functionality to dump fec statistics") introduces obtaining FEC correctable and uncorrectable stats per netdev in ICE driver. Unfortunately the assignment of values to fec_stats structure has been done incorrectly. This commit fixes the assignments. Fixes: ac21add2540e ("ice: Implement driver functionality to dump fec statistics") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07ice: Skip PTP HW writes during PTP reset procedureGrzegorz Nitka
Block HW write access for the driver while the device is in reset to avoid potential race condition and access to the PTP HW in non-nominal state which could lead to undesired effects Fixes: 4aad5335969f ("ice: add individual interrupt allocation") Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07ice: Fix reset handlerGrzegorz Nitka
Synchronize OICR IRQ when preparing for reset to avoid potential race conditions between the reset procedure and OICR Fixes: 4aad5335969f ("ice: add individual interrupt allocation") Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-31igc: Fix double reset adapter triggered from a single taprio cmdFaizal Rahim
Following the implementation of "igc: Add TransmissionOverrun counter" patch, when a taprio command is triggered by user, igc processes two commands: TAPRIO_CMD_REPLACE followed by TAPRIO_CMD_STATS. However, both commands unconditionally pass through igc_tsn_offload_apply() which evaluates and triggers reset adapter. The double reset causes issues in the calculation of adapter->qbv_count in igc. TAPRIO_CMD_REPLACE command is expected to reset the adapter since it activates qbv. It's unexpected for TAPRIO_CMD_STATS to do the same because it doesn't configure any driver-specific TSN settings. So, the evaluation in igc_tsn_offload_apply() isn't needed for TAPRIO_CMD_STATS. To address this, commands parsing are relocated to igc_tsn_enable_qbv_scheduling(). Commands that don't require an adapter reset will exit after processing, thus avoiding igc_tsn_offload_apply(). Fixes: d3750076d464 ("igc: Add TransmissionOverrun counter") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240730173304.865479-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-29ice: xsk: fix txq interrupt mappingMaciej Fijalkowski
ice_cfg_txq_interrupt() internally handles XDP Tx ring. Do not use ice_for_each_tx_ring() in ice_qvec_cfg_msix() as this causing us to treat XDP ring that belongs to queue vector as Tx ring and therefore misconfiguring the interrupts. Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-29ice: add missing WRITE_ONCE when clearing ice_rx_ring::xdp_progMaciej Fijalkowski
It is read by data path and modified from process context on remote cpu so it is needed to use WRITE_ONCE to clear the pointer. Fixes: efc2214b6047 ("ice: Add support for XDP") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-29ice: improve updating ice_{t,r}x_ring::xsk_poolMaciej Fijalkowski
xsk_buff_pool pointers that ice ring structs hold are updated via ndo_bpf that is executed in process context while it can be read by remote CPU at the same time within NAPI poll. Use synchronize_net() after pointer update and {READ,WRITE}_ONCE() when working with mentioned pointer. Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-29ice: toggle netif_carrier when setting up XSK poolMaciej Fijalkowski
This so we prevent Tx timeout issues. One of conditions checked on running in the background dev_watchdog() is netif_carrier_ok(), so let us turn it off when we disable the queues that belong to a q_vector where XSK pool is being configured. Turn carrier on in ice_qp_ena() only when ice_get_link_status() tells us that physical link is up. Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-29ice: modify error handling when setting XSK pool in ndo_bpfMaciej Fijalkowski
Don't bail out right when spotting an error within ice_qp_{dis,ena}() but rather track error and go through whole flow of disabling and enabling queue pair. Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-29ice: replace synchronize_rcu with synchronize_netMaciej Fijalkowski
Given that ice_qp_dis() is called under rtnl_lock, synchronize_net() can be called instead of synchronize_rcu() so that XDP rings can finish its job in a faster way. Also let us do this as earlier in XSK queue disable flow. Additionally, turn off regular Tx queue before disabling irqs and NAPI. Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-29ice: don't busy wait for Rx queue disable in ice_qp_dis()Maciej Fijalkowski
When ice driver is spammed with multiple xdpsock instances and flow control is enabled, there are cases when Rx queue gets stuck and unable to reflect the disable state in QRX_CTRL register. Similar issue has previously been addressed in commit 13a6233b033f ("ice: Add support to enable/disable all Rx queues before waiting"). To workaround this, let us simply not wait for a disabled state as later patch will make sure that regardless of the encountered error in the process of disabling a queue pair, the Rx queue will be enabled. Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-29ice: respect netif readiness in AF_XDP ZC related ndo'sMichal Kubiak
Address a scenario in which XSK ZC Tx produces descriptors to XDP Tx ring when link is either not yet fully initialized or process of stopping the netdev has already started. To avoid this, add checks against carrier readiness in ice_xsk_wakeup() and in ice_xmit_zc(). One could argue that bailing out early in ice_xsk_wakeup() would be sufficient but given the fact that we produce Tx descriptors on behalf of NAPI that is triggered for Rx traffic, the latter is also needed. Bringing link up is an asynchronous event executed within ice_service_task so even though interface has been brought up there is still a time frame where link is not yet ok. Without this patch, when AF_XDP ZC Tx is used simultaneously with stack Tx, Tx timeouts occur after going through link flap (admin brings interface down then up again). HW seem to be unable to transmit descriptor to the wire after HW tail register bump which in turn causes bit __QUEUE_STATE_STACK_XOFF to be set forever as netdev_tx_completed_queue() sees no cleaned bytes on the input. Fixes: 126cdfe1007a ("ice: xsk: Improve AF_XDP ZC Tx and use batching API") Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-25Merge tag 'net-6.11-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from bpf and netfilter. A lot of networking people were at a conference last week, busy catching COVID, so relatively short PR. Current release - regressions: - tcp: process the 3rd ACK with sk_socket for TFO and MPTCP Current release - new code bugs: - l2tp: protect session IDR and tunnel session list with one lock, make sure the state is coherent to avoid a warning - eth: bnxt_en: update xdp_rxq_info in queue restart logic - eth: airoha: fix location of the MBI_RX_AGE_SEL_MASK field Previous releases - regressions: - xsk: require XDP_UMEM_TX_METADATA_LEN to actuate tx_metadata_len, the field reuses previously un-validated pad Previous releases - always broken: - tap/tun: drop short frames to prevent crashes later in the stack - eth: ice: add a per-VF limit on number of FDIR filters - af_unix: disable MSG_OOB handling for sockets in sockmap/sockhash" * tag 'net-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (34 commits) tun: add missing verification for short frame tap: add missing verification for short frame mISDN: Fix a use after free in hfcmulti_tx() gve: Fix an edge case for TSO skb validity check bnxt_en: update xdp_rxq_info in queue restart logic tcp: process the 3rd ACK with sk_socket for TFO/MPTCP selftests/bpf: Add XDP_UMEM_TX_METADATA_LEN to XSK TX metadata test xsk: Require XDP_UMEM_TX_METADATA_LEN to actuate tx_metadata_len bpf: Fix a segment issue when downgrading gso_size net: mediatek: Fix potential NULL pointer dereference in dummy net_device handling MAINTAINERS: make Breno the netconsole maintainer MAINTAINERS: Update bonding entry net: nexthop: Initialize all fields in dumped nexthops net: stmmac: Correct byte order of perfect_match selftests: forwarding: skip if kernel not support setting bridge fdb learning limit tipc: Return non-zero value from tipc_udp_addr2str() on error netfilter: nft_set_pipapo_avx2: disable softinterrupts ice: Fix recipe read procedure ice: Add a per-VF limit on number of FDIR filters net: bonding: correctly annotate RCU in bond_should_notify_peers() ...
2024-07-25Merge tag 'driver-core-6.11-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here is the big set of driver core changes for 6.11-rc1. Lots of stuff in here, with not a huge diffstat, but apis are evolving which required lots of files to be touched. Highlights of the changes in here are: - platform remove callback api final fixups (Uwe took many releases to get here, finally!) - Rust bindings for basic firmware apis and initial driver-core interactions. It's not all that useful for a "write a whole driver in rust" type of thing, but the firmware bindings do help out the phy rust drivers, and the driver core bindings give a solid base on which others can start their work. There is still a long way to go here before we have a multitude of rust drivers being added, but it's a great first step. - driver core const api changes. This reached across all bus types, and there are some fix-ups for some not-common bus types that linux-next and 0-day testing shook out. This work is being done to help make the rust bindings more safe, as well as the C code, moving toward the end-goal of allowing us to put driver structures into read-only memory. We aren't there yet, but are getting closer. - minor devres cleanups and fixes found by code inspection - arch_topology minor changes - other minor driver core cleanups All of these have been in linux-next for a very long time with no reported problems" * tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits) ARM: sa1100: make match function take a const pointer sysfs/cpu: Make crash_hotplug attribute world-readable dio: Have dio_bus_match() callback take a const * zorro: make match function take a const pointer driver core: module: make module_[add|remove]_driver take a const * driver core: make driver_find_device() take a const * driver core: make driver_[create|remove]_file take a const * firmware_loader: fix soundness issue in `request_internal` firmware_loader: annotate doctests as `no_run` devres: Correct code style for functions that return a pointer type devres: Initialize an uninitialized struct member devres: Fix memory leakage caused by driver API devm_free_percpu() devres: Fix devm_krealloc() wasting memory driver core: platform: Switch to use kmemdup_array() driver core: have match() callback in struct bus_type take a const * MAINTAINERS: add Rust device abstractions to DRIVER CORE device: rust: improve safety comments MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER firmware: rust: improve safety comments ...
2024-07-23ice: Fix recipe read procedureWojciech Drewek
When ice driver reads recipes from firmware information about need_pass_l2 and allow_pass_l2 flags is not stored correctly. Those flags are stored as one bit each in ice_sw_recipe structure. Because of that, the result of checking a flag has to be casted to bool. Note that the need_pass_l2 flag currently works correctly, because it's stored in the first bit. Fixes: bccd9bce29e0 ("ice: Add guard rule when creating FDB in switchdev") Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-23ice: Add a per-VF limit on number of FDIR filtersAhmed Zaki
While the iavf driver adds a s/w limit (128) on the number of FDIR filters that the VF can request, a malicious VF driver can request more than that and exhaust the resources for other VFs. Add a similar limit in ice. CC: stable@vger.kernel.org Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Suggested-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-07-16Merge tag 'net-next-6.11' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: "Not much excitement - a handful of large patchsets (devmem among them) did not make it in time. Core & protocols: - Use local_lock in addition to local_bh_disable() to protect per-CPU resources in networking, a step closer for local_bh_disable() not to act as a big lock on PREEMPT_RT - Use flex array for netdevice priv area, ensure its cache alignment - Add a sysctl knob to allow user to specify a default rto_min at socket init time. Bit of a big hammer but multiple companies were independently carrying such patch downstream so clearly it's useful - Support scheduling transmission of packets based on CLOCK_TAI - Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned off using cpusets - Support multiple L2TPv3 UDP tunnels using the same 5-tuple address - Allow configuration of multipath hash seed, to both allow synchronizing hashing of two routers, and preventing partial accidental sync - Improve TCP compliance with RFC 9293 for simultaneous connect() - Support sending NAT keepalives in IPsec ESP in UDP states. Userspace IKE daemon had to do this before, but the kernel can better keep track of it - Support sending supervision HSR frames with MAC addresses stored in ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled - Introduce IPPROTO_SMC for selecting SMC when socket is created - Allow UDP GSO transmit from devices with no checksum offload - openvswitch: add packet sampling via psample, separating the sampled traffic from "upcall" packets sent to user space for forwarding - nf_tables: shrink memory consumption for transaction objects Things we sprinkled into general kernel code: - Power Sequencing subsystem (used by Qualcomm Bluetooth driver for QCA6390) [ Already merged separately - Linus ] - Add IRQ information in sysfs for auxiliary bus - Introduce guard definition for local_lock - Add aligned flavor of __cacheline_group_{begin, end}() markings for grouping fields in structures BPF: - Notify user space (via epoll) when a struct_ops object is getting detached/unregistered - Add new kfuncs for a generic, open-coded bits iterator - Enable BPF programs to declare arrays of kptr, bpf_rb_root, and bpf_list_head - Support resilient split BTF which cuts down on duplication and makes BTF as compact as possible WRT BTF from modules - Add support for dumping kfunc prototypes from BTF which enables both detecting as well as dumping compilable prototypes for kfuncs - riscv64 BPF JIT improvements in particular to add 12-argument support for BPF trampolines and to utilize bpf_prog_pack for the latter - Add the capability to offload the netfilter flowtable in XDP layer through kfuncs Driver API: - Allow users to configure IRQ tresholds between which automatic IRQ moderation can choose - Expand Power Sourcing (PoE) status with power, class and failure reason. Support setting power limits - Track additional RSS contexts in the core, make sure configuration changes don't break them - Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated ESP data paths - Support updating firmware on SFP modules Tests and tooling: - mptcp: use net/lib.sh to manage netns - TCP-AO and TCP-MD5: replace debug prints used by tests with tracepoints - openvswitch: make test self-contained (don't depend on OvS CLI tools) Drivers: - Ethernet high-speed NICs: - Broadcom (bnxt): - increase the max total outstanding PTP TX packets to 4 - add timestamping statistics support - implement netdev_queue_mgmt_ops - support new RSS context API - Intel (100G, ice, idpf): - implement FEC statistics and dumping signal quality indicators - support E825C products (with 56Gbps PHYs) - nVidia/Mellanox: - support HW-GRO - mlx4/mlx5: support per-queue statistics via netlink - obey the max number of EQs setting in sub-functions - AMD/Solarflare: - support new RSS context API - AMD/Pensando: - ionic: rework fix for doorbell miss to lower overhead and skip it on new HW - Wangxun: - txgbe: support Flow Director perfect filters - Ethernet NICs consumer, embedded and virtual: - Add driver for Tehuti Networks TN40xx chips - Add driver for Meta's internal NIC chips - Add driver for Ethernet MAC on Airoha EN7581 SoCs - Add driver for Renesas Ethernet-TSN devices - Google cloud vNIC: - flow steering support - Microsoft vNIC: - support page sizes other than 4KB on ARM64 - vmware vNIC: - support latency measurement (update to version 9) - VirtIO net: - support for Byte Queue Limits - support configuring thresholds for automatic IRQ moderation - support for AF_XDP Rx zero-copy - Synopsys (stmmac): - support for STM32MP13 SoC - let platforms select the right PCS implementation - TI: - icssg-prueth: add multicast filtering support - icssg-prueth: enable PTP timestamping and PPS - Renesas: - ravb: improve Rx performance 30-400% by using page pool, theaded NAPI and timer-based IRQ coalescing - ravb: add MII support for R-Car V4M - Cadence (macb): - macb: add ARP support to Wake-On-LAN - Cortina: - use phylib for RX and TX pause configuration - Ethernet switches: - nVidia/Mellanox: - support configuration of multipath hash seed - report more accurate max MTU - use page_pool to improve Rx performance - MediaTek: - mt7530: add support for bridge port isolation - Qualcomm: - qca8k: add support for bridge port isolation - Microchip: - lan9371/2: add 100BaseTX PHY support - NXP: - vsc73xx: implement VLAN operations - Ethernet PHYs: - aquantia: enable support for aqr115c - aquantia: add support for PHY LEDs - realtek: add support for rtl8224 2.5Gbps PHY - xpcs: add memory-mapped device support - add BroadR-Reach link mode and support in Broadcom's PHY driver - CAN: - add document for ISO 15765-2 protocol support - mcp251xfd: workaround for erratum DS80000789E, use timestamps to catch when device returns incorrect FIFO status - WiFi: - mac80211/cfg80211: - parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers - improvements for 6 GHz regulatory flexibility - multi-link improvements - support multiple radios per wiphy - remove DEAUTH_NEED_MGD_TX_PREP flag - Intel (iwlwifi): - bump FW API to 91 for BZ/SC devices - report 64-bit radiotap timestamp - enable P2P low latency by default - handle Transmit Power Envelope (TPE) advertised by AP - remove support for older FW for new devices - fast resume (keeping the device configured) - mvm: re-enable Multi-Link Operation (MLO) - aggregation (A-MSDU) optimizations - MediaTek (mt76): - mt7925 Multi-Link Operation (MLO) support - Qualcomm (ath10k): - LED support for various chipsets - Qualcomm (ath12k): - remove unsupported Tx monitor handling - support channel 2 in 6 GHz band - support Spatial Multiplexing Power Save (SMPS) in 6 GHz band - supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) - support dynamic VLAN - add panic handler for resetting the firmware state - DebugFS support for datapath statistics - WCN7850: support for Wake on WLAN - Microchip (wilc1000): - read MAC address during probe to make it visible to user space - suspend/resume improvements - TI (wl18xx): - support newer firmware versions - RealTek (rtw89): - preparation for RTL8852BE-VT support - Wake on WLAN support for WiFi 6 chips - 36-bit PCI DMA support - RealTek (rtlwifi): - RTL8192DU support - Broadcom (brcmfmac): - Management Frame Protection support (to enable WPA3) - Bluetooth: - qualcomm: use the power sequencer for QCA6390 - btusb: mediatek: add ISO data transmission functions - hci_bcm4377: add BCM4388 support - btintel: add support for BlazarU core - btintel: add support for Whale Peak2 - btnxpuart: add support for AW693 A1 chipset - btnxpuart: add support for IW615 chipset - btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591" * tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits) eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering" tcp: Replace strncpy() with strscpy() wifi: ath12k: fix build vs old compiler tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child(). eth: fbnic: Write the TCAM tables used for RSS control and Rx to host eth: fbnic: Add L2 address programming eth: fbnic: Add basic Rx handling eth: fbnic: Add basic Tx handling eth: fbnic: Add link detection eth: fbnic: Add initial messaging to notify FW of our presence eth: fbnic: Implement Rx queue alloc/start/stop/free eth: fbnic: Implement Tx queue alloc/start/stop/free eth: fbnic: Allocate a netdevice and napi vectors with queues eth: fbnic: Add FW communication mechanism eth: fbnic: Add message parsing for FW messages eth: fbnic: Add register init to set PCIe/Ethernet device config eth: fbnic: Allocate core device specific structures and devlink interface eth: fbnic: Add scaffolding for Meta's NIC driver PCI: Add Meta Platforms vendor ID net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK ...
2024-07-15Merge tag 'timers-core-2024-07-14' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer updates from Thomas Gleixner: "Updates for timers, timekeeping and related functionality: Core: - Make the takeover of a hrtimer based broadcast timer reliable during CPU hot-unplug. The current implementation suffers from a race which can lead to broadcast timer starvation in the worst case. - VDSO related cleanups and simplifications - Small cleanups and enhancements all over the place PTP: - Replace the architecture specific base clock to clocksource, e.g. ART to TSC, conversion function with generic functionality to avoid exposing such internals to drivers and convert all existing drivers over. This also allows to provide functionality which converts the other way round in the core code based on the same parameter set. - Provide a function to convert CLOCK_REALTIME to the base clock to support the upcoming PPS output driver on Intel platforms. Drivers: - A set of Device Tree bindings for new hardware - Cleanups and enhancements all over the place" * tag 'timers-core-2024-07-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits) clocksource/drivers/realtek: Add timer driver for rtl-otto platforms dt-bindings: timer: Add schema for realtek,otto-timer dt-bindings: timer: Add SOPHGO SG2002 clint dt-bindings: timer: renesas,tmu: Add R-Car Gen2 support dt-bindings: timer: renesas,tmu: Add RZ/G1 support dt-bindings: timer: renesas,tmu: Add R-Mobile APE6 support clocksource/drivers/mips-gic-timer: Correct sched_clock width clocksource/drivers/mips-gic-timer: Refine rating computation clocksource/drivers/sh_cmt: Address race condition for clock events clocksource/driver/arm_global_timer: Remove unnecessary ‘0’ values from err clocksource/drivers/arm_arch_timer: Remove unnecessary ‘0’ values from irq tick/broadcast: Make takeover of broadcast hrtimer reliable tick/sched: Combine WARN_ON_ONCE and print_once x86/vdso: Remove unused include x86/vgtod: Remove unused typedef gtod_long_t x86/vdso: Fix function reference in comment vdso: Add comment about reason for vdso struct ordering vdso/gettimeofday: Clarify comment about open coded function timekeeping: Add missing kernel-doc function comments tick: Remove unnused tick_nohz_get_idle_calls() ...
2024-07-15Merge branch 'net-make-timestamping-selectable'Jakub Kicinski
First part of "net: Make timestamping selectable" from Kory Maincent. Change the driver-facing type already to lower rebasing pain. Link: https://lore.kernel.org/20240709-feature_ptp_netnext-v17-0-b5317f50df2a@bootlin.com/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-15net: Add struct kernel_ethtool_ts_infoKory Maincent
In prevision to add new UAPI for hwtstamp we will be limited to the struct ethtool_ts_info that is currently passed in fixed binary format through the ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code already started operating on an extensible kernel variant of that structure, similar in concept to struct kernel_hwtstamp_config vs struct hwtstamp_config. Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here we introduce the kernel-only structure in include/linux/ethtool.h. The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO. Acked-by: Shannon Nelson <shannon.nelson@amd.com> Acked-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-14Merge branch '100GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== ice: Switch API optimizations Marcin Szycik says: Optimize the process of creating a recipe in the switch block by removing duplicate switch ID words and changing how result indexes are fitted into recipes. In many cases this can decrease the number of recipes required to add a certain set of rules, potentially allowing a more varied set of rules to be created. Total rule count will also increase, since less words will be left unused/wasted. There are only 64 rules available in total, so every one counts. After this modification, many fields and some structs became unused or were simplified, resulting in overall simpler implementation. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: ice: Add tracepoint for adding and removing switch rules ice: Remove unused members from switch API ice: Optimize switch recipe creation ice: remove unused recipe bookkeeping data ice: Simplify bitmap setting in adding recipe ice: Remove reading all recipes before adding a new one ice: Remove unused struct ice_prot_lkup_ext members ==================== Link: https://patch.msgid.link/20240711181312.2019606-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generated by cgit v1.2.3-70-g09d2 (git 2.48.1) at 2025-07-29 18:47:12 +0000