summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2020-07-21net: hns3: fix for not calculating TX BD send size correctlyYunsheng Lin
With GRO and fraglist support, the SKB can be aggregated to a total size of 65535, and when that SKB is forwarded through a bridge, the size of the SKB may be pushed to exceed the size of 65535 when br_dev_queue_push_xmit() is called. The max send size of BD supported by the HW is 65535, when a SKB with a headlen of over 65535 is sent to the driver, the driver needs to use multi BD to send the linear data, and the send size of the last BD is calculated incorrectly by the driver who is using '&' operation, which causes a TX error. Use '%' operation to fix this problem. Fixes: 3fe13ed95dd3 ("net: hns3: avoid mult + div op in critical data path") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: hns3: fix for not unmapping TX buffer correctlyYunsheng Lin
When a big TX buffer is sent using multi BD, the driver maps the whole TX buffer, and unmaps it using info in desc_cb corresponding to each BD, but only the info in the desc_cb of first BD is correct, other info in desc_cb is wrong, which causes TX unmapping problem when SMMU is on. Only set the mapping and freeing info in the desc_cb of first BD to fix this problem, because the TX buffer only need to be unmapped and freed once. Fixes: 1e8a7977d09f("net: hns3: add handling for big TX fragment") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huzhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: ethernet: ravb: exit if re-initialization fails in tx timeoutYoshihiro Shimoda
According to the report of [1], this driver is possible to cause the following error in ravb_tx_timeout_work(). ravb e6800000.ethernet ethernet: failed to switch device to config mode This error means that the hardware could not change the state from "Operation" to "Configuration" while some tx and/or rx queue are operating. After that, ravb_config() in ravb_dmac_init() will fail, and then any descriptors will be not allocaled anymore so that NULL pointer dereference happens after that on ravb_start_xmit(). To fix the issue, the ravb_tx_timeout_work() should check the return values of ravb_stop_dma() and ravb_dmac_init(). If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX and just exits. If ravb_dmac_init() fails, just exits. [1] https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/ Reported-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20net: neterion: vxge: reduce stack usage in VXGE_COMPLETE_VPATH_TXBixuan Cui
Fix the warning: [-Werror=-Wframe-larger-than=] drivers/net/ethernet/neterion/vxge/vxge-main.c: In function'VXGE_COMPLETE_VPATH_TX.isra.37': drivers/net/ethernet/neterion/vxge/vxge-main.c:119:1: warning: the frame size of 1056 bytes is larger than 1024 bytes Dropping the NR_SKB_COMPLETED to 16 is appropriate that won't have much impact on performance and functionality. Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20net: ag71xx: add missed clk_disable_unprepare in error path of probeHuang Guobin
The ag71xx_mdio_probe() forgets to call clk_disable_unprepare() when of_reset_control_get_exclusive() failed. Add the missed call to fix it. Fixes: d51b6ce441d3 ("net: ethernet: add ag71xx driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Huang Guobin <huangguobin4@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20ionic: use mutex to protect queue operationsShannon Nelson
The ionic_wait_on_bit_lock() was a open-coded mutex knock-off used only for protecting the queue reset operations, and there was no reason not to use the real thing. We can use the lock more correctly and to better protect the queue stop and start operations from cross threading. We can also remove a useless and expensive bit operation from the Rx path. This fixes a case found where the link_status_check from a link flap could run into an MTU change and cause a crash. Fixes: beead698b173 ("ionic: Add the basic NDO callbacks for netdev support") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20ionic: keep rss hash after fw updateShannon Nelson
Make sure the RSS hash key is kept across a fw update by not de-initing it when an update is happening. Fixes: c672412f6172 ("ionic: remove lifs on fw reset") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20ionic: update filter id after replayShannon Nelson
When we replay the rx filters after a fw-upgrade we get new filter_id values from the FW, which we need to save and update in our local filter list. This allows us to delete the filters with the correct filter_id when we're done. Fixes: 7e4d47596b68 ("ionic: replay filters after fw upgrade") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20ionic: fix up filter locks and debug msgsShannon Nelson
Add in a couple of forgotten spinlocks and fix up some of the debug messages around filter management. Fixes: c1e329ebec8d ("ionic: Add management of rx filters") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20ionic: use offset for ethtool regs dataShannon Nelson
Use an offset to write the second half of the regs data into the second half of the buffer instead of overwriting the first half. Fixes: 4d03e00a2140 ("ionic: Add initial ethtool support") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20mlxsw: destroy workqueue when trap_register in mlxsw_emad_initLiu Jian
When mlxsw_core_trap_register fails in mlxsw_emad_init, destroy_workqueue() shouled be called to destroy mlxsw_core->emad_wq. Fixes: d965465b60ba ("mlxsw: core: Fix possible deadlock") Signed-off-by: Liu Jian <liujian56@huawei.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20dpaa_eth: Fix one possible memleak in dpaa_eth_probeLiu Jian
When dma_coerce_mask_and_coherent() fails, the alloced netdev need to be freed. Fixes: 060ad66f9795 ("dpaa_eth: change DMA device") Signed-off-by: Liu Jian <liujian56@huawei.com> Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20net: bcmgenet: add missed clk_disable_unprepare in bcmgenet_probeZhang Changzhong
The driver forgets to call clk_disable_unprepare() in error path after a success calling for clk_prepare_enable(). Fix to goto err_clk_disable if clk_prepare_enable() is successful. Fixes: c80d36ff63a5 ("net: bcmgenet: Use devm_clk_get_optional() to get the clocks") Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20net: bcmgenet: fix error returns in bcmgenet_probe()Zhang Changzhong
The driver forgets to call clk_disable_unprepare() in error path after a success calling for clk_prepare_enable(). Fix to goto err_clk_disable if clk_prepare_enable() is successful. Fixes: 99d55638d4b0 ("net: bcmgenet: enable NETIF_F_HIGHDMA flag") Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-17mlxsw: core: Fix wrong SFP EEPROM reading for upper pages 1-3Vadim Pasternak
Fix wrong reading of upper pages for SFP EEPROM. According to "Memory Organization" figure in SFF-8472 spec: When reading upper pages 1, 2 and 3 the offset should be set relative to zero and I2C high address 0x51 [1010001X (A2h)] is to be used. Fixes: a45bfb5a5070 ("mlxsw: core: Extend QSFP EEPROM size for ethtool") Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-17net: macb: use phy_interface_mode_is_rgmii everywhereAlexandre Belloni
There is one RGMII check not using the phy_interface_mode_is_rgmii() helper. This prevents the driver from configuring the MAC properly when using a phy-mode that is not just rgmii, e.g. rgmii-rxid. This became an issue on sama5d3 xplained since the ksz9031 driver is hadling phy-mode properly and the phy-mode has to be set to rgmii-rxid. Fixes: bcf3440c6dd78bfe ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-17net: atlantic: disable PTP on AQC111, AQC112Nikita Danilov
This patch disables PTP on AQC111 and AQC112 due to a known HW issue, which can cause datapath issues. Ideally PTP block should have been disabled via PHY provisioning, but unfortunately many units have been shipped with enabled PTP block. Thus, we have to work around this in the driver. Fixes: dbcd6806af420 ("net: aquantia: add support for Phy access") Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-17net: bcmgenet: restore HFB filters on resumeDoug Berger
The Hardware Filter Block RAM may not be preserved when the GENET block is reset during a deep sleep, so it is not sufficient to only backup and restore the enables. This commit clears out the HFB block and reprograms the rxnfc rules when the system resumes from a suspended state. To support this the bcmgenet_hfb_create_rxnfc_filter() function is modified to access the register space directly so that it can't fail due to memory allocation issues. Fixes: f50932cca632 ("net: bcmgenet: add WAKE_FILTER support") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-17net: bcmgenet: test RBUF_ACPI_EN when resumingDoug Berger
When the GENET driver resumes from deep sleep the UMAC_CMD register may not be accessible and therefore should not be accessed from bcmgenet_wol_power_up_cfg() if the GENET has been reset. This commit adds a check of the RBUF_ACPI_EN flag when Wake on Filter is enabled. A clear flag indicates that the GENET hardware must have been reset so the remainder of the hardware programming is bypassed. Fixes: f50932cca632 ("net: bcmgenet: add WAKE_FILTER support") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-17net: bcmgenet: test MPD_EN when resumingDoug Berger
When the GENET driver resumes from deep sleep the UMAC_CMD register may not be accessible and therefore should not be accessed from bcmgenet_wol_power_up_cfg() if the GENET has been reset. This commit adds a check of the MPD_EN flag when Wake on Magic Packet is enabled. A clear flag indicates that the GENET hardware must have been reset so the remainder of the hardware programming is bypassed. Fixes: 1a1d5106c1e3 ("net: bcmgenet: move clk_wol management to bcmgenet_wol") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-17net: smc91x: Fix possible memory leak in smc_drv_probe()Wang Hai
If try_toggle_control_gpio() failed in smc_drv_probe(), free_netdev(ndev) should be called to free the ndev created earlier. Otherwise, a memleak will occur. Fixes: 7d2911c43815 ("net: smc91x: Fix gpios for device tree based booting") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-16net: fec: fix hardware time stamping by external devicesSergey Organov
Fix support for external PTP-aware devices such as DSA or PTP PHY: Make sure we never time stamp tx packets when hardware time stamping is disabled. Check for PTP PHY being in use and then pass ioctls related to time stamping of Ethernet packets to the PTP PHY rather than handle them ourselves. In addition, disable our own hardware time stamping in this case. Fixes: 6605b730c061 ("FEC: Add time stamping code and a PTP hardware clock") Signed-off-by: Sergey Organov <sorganov@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-07-15dpaa2-eth: check fsl_mc_get_endpoint for IS_ERR_OR_NULL()Ioana Ciornei
The fsl_mc_get_endpoint() function can return an error or directly a NULL pointer in case the peer device is not under the root DPRC container. Treat this case also, otherwise it would lead to a NULL pointer when trying to access the peer fsl_mc_device. Fixes: 719479230893 ("dpaa2-eth: add MAC/PHY support through phylink") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-07-14qed: Disable "MFW indication via attention" SPAM every 5 minutesLaurence Oberman
This is likely firmware causing this but its starting to annoy customers. Change the message level to verbose to prevent the spam. Note that this seems to only show up with ISCSI enabled on the HBA via the qedi driver. Signed-off-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14gianfar: Use random MAC address when none is givenMaxim Kochetkov
If there is no valid MAC address in the device tree, use a random MAC address. Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-12bnxt_en: Fix completion ring sizing with TPA enabled.Michael Chan
The current completion ring sizing formula is wrong with TPA enabled. The formula assumes that the number of TPA completions are bound by the RX ring size, but that's not true. TPA_START completions are immediately recycled so they are not bound by the RX ring size. We must add bp->max_tpa to the worst case maximum RX and TPA completions. The completion ring can overflow because of this mistake. This will cause hardware to disable the completion ring when this happens, leading to RX and TX traffic to stall on that ring. This issue is generally exposed only when the RX ring size is set very small. Fix the formula by adding bp->max_tpa to the number of RX completions if TPA is enabled. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver."); Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-12bnxt_en: Init ethtool link settings after reading updated PHY configuration.Vasundhara Volam
In a shared port PHY configuration, async event is received when any of the port modifies the configuration. Ethtool link settings should be initialised after updated PHY configuration from firmware. Fixes: b1613e78e98d ("bnxt_en: Add async. event logic for PHY configuration changes.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-12bnxt_en: Fix race when modifying pause settings.Vasundhara Volam
The driver was modified to not rely on rtnl lock to protect link settings about 2 years ago. The pause setting was missed when making that change. Fix it by acquiring link_lock mutex before calling bnxt_hwrm_set_pause(). Fixes: e2dc9b6e38fa ("bnxt_en: Don't use rtnl lock to protect link change logic in workqueue.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-10mlxsw: pci: Fix use-after-free in case of failed devlink reloadIdo Schimmel
In case devlink reload failed, it is possible to trigger a use-after-free when querying the kernel for device info via 'devlink dev info' [1]. This happens because as part of the reload error path the PCI command interface is de-initialized and its mailboxes are freed. When the devlink '->info_get()' callback is invoked the device is queried via the command interface and the freed mailboxes are accessed. Fix this by initializing the command interface once during probe and not during every reload. This is consistent with the other bus used by mlxsw (i.e., 'mlxsw_i2c') and also allows user space to query the running firmware version (for example) from the device after a failed reload. [1] BUG: KASAN: use-after-free in memcpy include/linux/string.h:406 [inline] BUG: KASAN: use-after-free in mlxsw_pci_cmd_exec+0x177/0xa60 drivers/net/ethernet/mellanox/mlxsw/pci.c:1675 Write of size 4096 at addr ffff88810ae32000 by task syz-executor.1/2355 CPU: 1 PID: 2355 Comm: syz-executor.1 Not tainted 5.8.0-rc2+ #29 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xf6/0x16e lib/dump_stack.c:118 print_address_description.constprop.0+0x1c/0x250 mm/kasan/report.c:383 __kasan_report mm/kasan/report.c:513 [inline] kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530 check_memory_region_inline mm/kasan/generic.c:186 [inline] check_memory_region+0x14e/0x1b0 mm/kasan/generic.c:192 memcpy+0x39/0x60 mm/kasan/common.c:106 memcpy include/linux/string.h:406 [inline] mlxsw_pci_cmd_exec+0x177/0xa60 drivers/net/ethernet/mellanox/mlxsw/pci.c:1675 mlxsw_cmd_exec+0x249/0x550 drivers/net/ethernet/mellanox/mlxsw/core.c:2335 mlxsw_cmd_access_reg drivers/net/ethernet/mellanox/mlxsw/cmd.h:859 [inline] mlxsw_core_reg_access_cmd drivers/net/ethernet/mellanox/mlxsw/core.c:1938 [inline] mlxsw_core_reg_access+0x2f6/0x540 drivers/net/ethernet/mellanox/mlxsw/core.c:1985 mlxsw_reg_query drivers/net/ethernet/mellanox/mlxsw/core.c:2000 [inline] mlxsw_devlink_info_get+0x17f/0x6e0 drivers/net/ethernet/mellanox/mlxsw/core.c:1090 devlink_nl_info_fill.constprop.0+0x13c/0x2d0 net/core/devlink.c:4588 devlink_nl_cmd_info_get_dumpit+0x246/0x460 net/core/devlink.c:4648 genl_lock_dumpit+0x85/0xc0 net/netlink/genetlink.c:575 netlink_dump+0x515/0xe50 net/netlink/af_netlink.c:2245 __netlink_dump_start+0x53d/0x830 net/netlink/af_netlink.c:2353 genl_family_rcv_msg_dumpit.isra.0+0x296/0x300 net/netlink/genetlink.c:638 genl_family_rcv_msg net/netlink/genetlink.c:733 [inline] genl_rcv_msg+0x78d/0x9d0 net/netlink/genetlink.c:753 netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469 genl_rcv+0x24/0x40 net/netlink/genetlink.c:764 netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline] netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329 netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg+0x150/0x190 net/socket.c:672 ____sys_sendmsg+0x6d8/0x840 net/socket.c:2363 ___sys_sendmsg+0xff/0x170 net/socket.c:2417 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2450 do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: a9c8336f6544 ("mlxsw: core: Add support for devlink info command") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-10mlxsw: spectrum_router: Remove inappropriate usage of WARN_ON()Ido Schimmel
We should not trigger a warning when a memory allocation fails. Remove the WARN_ON(). The warning is constantly triggered by syzkaller when it is injecting faults: [ 2230.758664] FAULT_INJECTION: forcing a failure. [ 2230.758664] name failslab, interval 1, probability 0, space 0, times 0 [ 2230.762329] CPU: 3 PID: 1407 Comm: syz-executor.0 Not tainted 5.8.0-rc2+ #28 ... [ 2230.898175] WARNING: CPU: 3 PID: 1407 at drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:6265 mlxsw_sp_router_fib_event+0xfad/0x13e0 [ 2230.898179] Kernel panic - not syncing: panic_on_warn set ... [ 2230.898183] CPU: 3 PID: 1407 Comm: syz-executor.0 Not tainted 5.8.0-rc2+ #28 [ 2230.898190] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Fixes: 3057224e014c ("mlxsw: spectrum_router: Implement FIB offload in deferred work") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-10net: macb: fix call to pm_runtime in the suspend/resume functionsNicolas Ferre
The calls to pm_runtime_force_suspend/resume() functions are only relevant if the device is not configured to act as a WoL wakeup source. Add the device_may_wakeup() test before calling them. Fixes: 3e2a5e153906 ("net: macb: add wake-on-lan support via magic packet") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Cc: Sergio Prado <sergio.prado@e-labworks.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-10net: macb: fix macb_suspend() by removing call to netif_carrier_off()Nicolas Ferre
As we now use the phylink call to phylink_stop() in the non-WoL path, there is no need for this call to netif_carrier_off() anymore. It can disturb the underlying phylink FSM. Fixes: 7897b071ac3b ("net: macb: convert to phylink") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Cc: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-10net: macb: fix macb_get/set_wol() when moving to phylinkNicolas Ferre
Keep previous function goals and integrate phylink actions to them. phylink_ethtool_get_wol() is not enough to figure out if Ethernet driver supports Wake-on-Lan. Initialization of "supported" and "wolopts" members is done in phylink function, no need to keep them in calling function. phylink_ethtool_set_wol() return value is considered and determines if the MAC has to handle WoL or not. The case where the PHY doesn't implement WoL leads to the MAC configuring it to provide this feature. Fixes: 7897b071ac3b ("net: macb: convert to phylink") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Cc: Antoine Tenart <antoine.tenart@bootlin.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-10net: macb: mark device wake capable when "magic-packet" property presentNicolas Ferre
Change the way the "magic-packet" DT property is handled in the macb_probe() function, matching DT binding documentation. Now we mark the device as "wakeup capable" instead of calling the device_init_wakeup() function that would enable the wakeup source. For Ethernet WoL, enabling the wakeup_source is done by using ethtool and associated macb_set_wol() function that already calls device_set_wakeup_enable() for this purpose. That would reduce power consumption by cutting more clocks if "magic-packet" property is set but WoL is not configured by ethtool. Fixes: 3e2a5e153906 ("net: macb: add wake-on-lan support via magic packet") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Cc: Sergio Prado <sergio.prado@e-labworks.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-10net: macb: fix wakeup test in runtime suspend/resume routinesNicolas Ferre
Use the proper struct device pointer to check if the wakeup flag and wakeup source are positioned. Use the one passed by function call which is equivalent to &bp->dev->dev.parent. It's preventing the trigger of a spurious interrupt in case the Wake-on-Lan feature is used. Fixes: d54f89af6cc4 ("net: macb: Add pm runtime support") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-10bnxt_en: fix NULL dereference in case SR-IOV configuration failsDavide Caratti
we need to set 'active_vfs' back to 0, if something goes wrong during the allocation of SR-IOV resources: otherwise, further VF configurations will wrongly assume that bp->pf.vf[x] are valid memory locations, and commands like the ones in the following sequence: # echo 2 >/sys/bus/pci/devices/${ADDR}/sriov_numvfs # ip link set dev ens1f0np0 up # ip link set dev ens1f0np0 vf 0 trust on will cause a kernel crash similar to this: bnxt_en 0000:3b:00.0: not enough MMIO resources for SR-IOV BUG: kernel NULL pointer dereference, address: 0000000000000014 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 43 PID: 2059 Comm: ip Tainted: G I 5.8.0-rc2.upstream+ #871 Hardware name: Dell Inc. PowerEdge R740/08D89F, BIOS 2.2.11 06/13/2019 RIP: 0010:bnxt_set_vf_trust+0x5b/0x110 [bnxt_en] Code: 44 24 58 31 c0 e8 f5 fb ff ff 85 c0 0f 85 b6 00 00 00 48 8d 1c 5b 41 89 c6 b9 0b 00 00 00 48 c1 e3 04 49 03 9c 24 f0 0e 00 00 <8b> 43 14 89 c2 83 c8 10 83 e2 ef 45 84 ed 49 89 e5 0f 44 c2 4c 89 RSP: 0018:ffffac6246a1f570 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000000000000b RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff98b28f538900 RBP: ffff98b28f538900 R08: 0000000000000000 R09: 0000000000000008 R10: ffffffffb9515be0 R11: ffffac6246a1f678 R12: ffff98b28f538000 R13: 0000000000000001 R14: 0000000000000000 R15: ffffffffc05451e0 FS: 00007fde0f688800(0000) GS:ffff98baffd40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000014 CR3: 000000104bb0a003 CR4: 00000000007606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: do_setlink+0x994/0xfe0 __rtnl_newlink+0x544/0x8d0 rtnl_newlink+0x47/0x70 rtnetlink_rcv_msg+0x29f/0x350 netlink_rcv_skb+0x4a/0x110 netlink_unicast+0x21d/0x300 netlink_sendmsg+0x329/0x450 sock_sendmsg+0x5b/0x60 ____sys_sendmsg+0x204/0x280 ___sys_sendmsg+0x88/0xd0 __sys_sendmsg+0x5e/0xa0 do_syscall_64+0x47/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: c0c050c58d840 ("bnxt_en: New Broadcom ethernet driver.") Reported-by: Fei Liu <feliu@redhat.com> CC: Jonathan Toppins <jtoppins@redhat.com> CC: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Acked-by: Jonathan Toppins <jtoppins@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-09net/mlx5e: CT: Fix memory leak in cleanupEli Britstein
CT entries are deleted via a workqueue from netfilter. If removing the module before that, the rules are cleaned by the driver itself, but the memory entries for them are not freed. Fix that. Fixes: ac991b48d43c ("net/mlx5e: CT: Offload established flows") Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-09net/mlx5e: Fix port buffers cell size valueEran Ben Elisha
Device unit for port buffers size, xoff_threshold and xon_threshold is cells. Fix a bug in driver where cell unit size was hard-coded to 128 bytes. This hard-coded value is buggy, as it is wrong for some hardware versions. Driver to read cell size from SBCAM register and translate bytes to cell units accordingly. In order to fix the bug, this patch exposes SBCAM (Shared buffer capabilities mask) layout and defines. If SBCAM.cap_cell_size is valid, use it for all bytes to cells calculations. If not valid, fallback to 128. Cell size do not change on the fly per device. Instead of issuing SBCAM access reg command every time such translation is needed, cache it in mlx5e_dcbx as part of mlx5e_dcbnl_initialize(). Pass dcbx.port_buff_cell_sz as a param to every function that needs bytes to cells translation. While fixing the bug, move MLX5E_BUFFER_CELL_SHIFT macro to en_dcbnl.c, as it is only used by that file. Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-09net/mlx5e: Fix 50G per lane indicationAya Levin
Some released FW versions mistakenly don't set the capability that 50G per lane link-modes are supported for VFs (ptys_extended_ethernet capability bit). When the capability is unset, read PTYS.ext_eth_proto_capability (always reliable). If PTYS.ext_eth_proto_capability is valid (has a non-zero value) conclude that the HCA supports 50G per lane. Otherwise, conclude that the HCA doesn't support 50G per lane. Fixes: a08b4ed1373d ("net/mlx5: Add support to ext_* fields introduced in Port Type and Speed register") Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-09net/mlx5e: Fix CPU mapping after function reload to avoid aRFS RX crashAya Levin
After function reload, CPU mapping used by aRFS RX is broken, leading to a kernel panic. Fix by moving initialization of rx_cpu_rmap from netdev_init to netdev_attach. IRQ table is re-allocated on mlx5_load, but netdev is not re-initialize. Trace of the panic: [ 22.055672] general protection fault, probably for non-canonical address 0x785634120000ff1c: 0000 [#1] SMP PTI [ 22.065010] CPU: 4 PID: 0 Comm: swapper/4 Not tainted 5.7.0-rc2-for-upstream-perf-2020-04-21_16-34-03-31 #1 [ 22.067967] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 22.071174] RIP: 0010:get_rps_cpu+0x267/0x300 [ 22.075692] RSP: 0018:ffffc90000244d60 EFLAGS: 00010202 [ 22.076888] RAX: ffff888459b0e400 RBX: 0000000000000000 RCX:0000000000000007 [ 22.078364] RDX: 0000000000008884 RSI: ffff888467cb5b00 RDI:0000000000000000 [ 22.079815] RBP: 00000000ff342b27 R08: 0000000000000007 R09:0000000000000003 [ 22.081289] R10: ffffffffffffffff R11: 00000000000070cc R12:ffff888454900000 [ 22.082767] R13: ffffc90000e5a950 R14: ffffc90000244dc0 R15:0000000000000007 [ 22.084190] FS: 0000000000000000(0000) GS:ffff88846fc80000(0000)knlGS:0000000000000000 [ 22.086161] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 22.087427] CR2: ffffffffffffffff CR3: 0000000464426003 CR4:0000000000760ee0 [ 22.088888] DR0: 0000000000000000 DR1: 0000000000000000 DR2:0000000000000000 [ 22.090336] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:0000000000000400 [ 22.091764] PKRU: 55555554 [ 22.092618] Call Trace: [ 22.093442] <IRQ> [ 22.094211] ? kvm_clock_get_cycles+0xd/0x10 [ 22.095272] netif_receive_skb_list_internal+0x258/0x2a0 [ 22.096460] gro_normal_list.part.137+0x19/0x40 [ 22.097547] napi_complete_done+0xc6/0x110 [ 22.098685] mlx5e_napi_poll+0x190/0x670 [mlx5_core] [ 22.099859] net_rx_action+0x2a0/0x400 [ 22.100848] __do_softirq+0xd8/0x2a8 [ 22.101829] irq_exit+0xa5/0xb0 [ 22.102750] do_IRQ+0x52/0xd0 [ 22.103654] common_interrupt+0xf/0xf [ 22.104641] </IRQ> Fixes: 4383cfcc65e7 ("net/mlx5: Add devlink reload") Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-09net/mlx5e: Fix VXLAN configuration restore after function reloadAya Levin
When detaching netdev, remove vxlan port configuration using udp_tunnel_drop_rx_info. During function reload, configuration will be restored using udp_tunnel_get_rx_info. This ensures sync between firmware and driver. Use udp_tunnel_get_rx_info even if its physical interface is down. Fixes: 4383cfcc65e7 ("net/mlx5: Add devlink reload") Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-09net/mlx5e: Fix usage of rcu-protected pointerVlad Buslov
In mlx5e_configure_flower() flow pointer is protected by rcu read lock. However, after cited commit the pointer is being used outside of rcu read block. Extend the block to protect all pointer accesses. Fixes: 553f9328385d ("net/mlx5e: Support tc block sharing for representors") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-09net/mxl5e: Verify that rpriv is not NULLVlad Buslov
In helper function is_flow_rule_duplicate_allowed() verify that rpviv pointer is not NULL before dereferencing it. This can happen when device is in NIC mode and leads to following crash: [90444.046419] BUG: kernel NULL pointer dereference, address: 0000000000000000 [90444.048149] #PF: supervisor read access in kernel mode [90444.049781] #PF: error_code(0x0000) - not-present page [90444.051386] PGD 80000003d35a4067 P4D 80000003d35a4067 PUD 3d35a3067 PMD 0 [90444.053051] Oops: 0000 [#1] SMP PTI [90444.054683] CPU: 16 PID: 31736 Comm: tc Not tainted 5.8.0-rc1+ #1157 [90444.056340] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017 [90444.058079] RIP: 0010:mlx5e_configure_flower+0x3aa/0x9b0 [mlx5_core] [90444.059753] Code: 24 50 49 8b 95 08 02 00 00 48 b8 00 08 00 00 04 00 00 00 48 21 c2 48 39 c2 74 0a 41 f6 85 0d 02 00 00 20 74 16 48 8b 44 24 20 <48> 8b 00 66 83 78 20 ff 74 07 4d 89 aa e0 00 00 00 48 83 7d 28 00 [90444.063232] RSP: 0018:ffffabe9c61ff768 EFLAGS: 00010246 [90444.065014] RAX: 0000000000000000 RBX: ffff9b13c4c91e80 RCX: 00000000000093fa [90444.066784] RDX: 0000000400000800 RSI: 0000000000000000 RDI: 000000000002d5e0 [90444.068533] RBP: ffff9b174d308468 R08: 0000000000000000 R09: ffff9b17d63003f0 [90444.070285] R10: ffff9b17ea288600 R11: 0000000000000000 R12: ffffabe9c61ff878 [90444.072032] R13: ffff9b174d300000 R14: ffffabe9c61ffbb8 R15: ffff9b174d300880 [90444.073760] FS: 00007f3c23775480(0000) GS:ffff9b13efc80000(0000) knlGS:0000000000000000 [90444.075492] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [90444.077266] CR2: 0000000000000000 CR3: 00000003e2a60002 CR4: 00000000001606e0 [90444.079024] Call Trace: [90444.080753] tc_setup_cb_add+0xca/0x1e0 [90444.082415] fl_hw_replace_filter+0x15f/0x1f0 [cls_flower] [90444.084119] fl_change+0xa59/0x13dc [cls_flower] [90444.085772] ? wait_for_completion+0xa8/0xf0 [90444.087364] tc_new_tfilter+0x3f5/0xa60 [90444.088960] rtnetlink_rcv_msg+0xeb/0x360 [90444.090514] ? __d_lookup_done+0x76/0xe0 [90444.092034] ? proc_alloc_inode+0x16/0x70 [90444.093560] ? prep_new_page+0x8c/0xf0 [90444.095048] ? _cond_resched+0x15/0x30 [90444.096483] ? rtnl_calcit.isra.0+0x110/0x110 [90444.097907] netlink_rcv_skb+0x49/0x110 [90444.099289] netlink_unicast+0x191/0x230 [90444.100629] netlink_sendmsg+0x243/0x480 [90444.101984] sock_sendmsg+0x5e/0x60 [90444.103305] ____sys_sendmsg+0x1f3/0x260 [90444.104597] ? copy_msghdr_from_user+0x5c/0x90 [90444.105916] ? __mod_lruvec_state+0x3c/0xe0 [90444.107210] ___sys_sendmsg+0x81/0xc0 [90444.108484] ? do_filp_open+0xa5/0x100 [90444.109732] ? handle_mm_fault+0x117b/0x1e00 [90444.110970] ? __check_object_size+0x46/0x147 [90444.112205] ? __check_object_size+0x136/0x147 [90444.113402] __sys_sendmsg+0x59/0xa0 [90444.114587] do_syscall_64+0x4d/0x90 [90444.115782] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [90444.116953] RIP: 0033:0x7f3c2393b7b8 [90444.118101] Code: Bad RIP value. [90444.119240] RSP: 002b:00007ffc6ad8e6c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e [90444.120408] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f3c2393b7b8 [90444.121583] RDX: 0000000000000000 RSI: 00007ffc6ad8e740 RDI: 0000000000000003 [90444.122750] RBP: 000000005eea0c3a R08: 0000000000000001 R09: 00007ffc6ad8e68c [90444.123928] R10: 0000000000404fa8 R11: 0000000000000246 R12: 0000000000000001 [90444.125073] R13: 0000000000000000 R14: 00007ffc6ad92a00 R15: 00000000004866a0 [90444.126221] Modules linked in: act_skbedit act_tunnel_key act_mirred bonding vxlan ip6_udp_tunnel udp_tunnel nfnetlink act_gact cls_flower sch_ingress openvswitch nsh nf_conncount nfsv3 nfs_acl nfs lockd grace fscache tun bridge stp llc sunrpc rdma_ucm rdma_cm iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5_core intel_r apl_msr intel_rapl_common sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel mlxfw kvm act_ct nf_flow_table nf_nat nf_conntrack irqbypass crct10dif_pclmul nf_defrag_ipv6 igb ipmi_ssif libcrc32c crc32_pclmul crc32c_intel ipmi_si nf_defrag_ipv4 ptp ghash_clmulni_intel mei_me ses iTCO_wdt i2c_i801 pps_core ioatdma iTCO_vendor_support joydev mei enclosure intel_cstate i2c_smbus wmi dca ipmi_devintf intel_uncore lpc_ich ipmi_msghandler pcspkr acpi_pad acpi_power_meter ast i2c_algo_bit drm_vram_helper drm_kms_helper drm_ttm_helper ttm drm mpt3sas raid_class scsi_transport_sas [90444.136253] CR2: 0000000000000000 [90444.137621] ---[ end trace 924af62aa2b151bd ]--- Fixes: 553f9328385d ("net/mlx5e: Support tc block sharing for representors") Reported-by: David Ahern <dsahern@gmail.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-09net/mlx5: E-Switch, Fix vlan or qos setting in legacy modeVu Pham
Refactoring eswitch ingress acl codes accidentally inserts extra memset zero that removes vlan and/or qos setting in legacy mode. Fixes: 07bab9502641 ("net/mlx5: E-Switch, Refactor eswitch ingress acl codes") Signed-off-by: Vu Pham <vuhuong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-09net/mlx5: Fix eeprom support for SFP moduleEran Ben Elisha
Fix eeprom SFP query support by setting i2c_addr, offset and page number correctly. Unlike QSFP modules, SFP eeprom params are as follow: - i2c_addr is 0x50 for offset 0 - 255 and 0x51 for offset 256 - 511. - Page number is always zero. - Page offset is always relative to zero. As part of eeprom query, query the module ID (SFP / QSFP*) via helper function to set the params accordingly. In addition, change mlx5_qsfp_eeprom_page() input type to be u16 to avoid unnecessary casting. Fixes: a708fb7b1f8d ("net/mlx5e: ethtool, Add support for EEPROM high pages query") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-09qed: Populate nvm-file attributes while reading nvm config partition.Sudarsana Reddy Kalluru
NVM config file address will be modified when the MBI image is upgraded. Driver would return stale config values if user reads the nvm-config (via ethtool -d) in this state. The fix is to re-populate nvm attribute info while reading the nvm config values/partition. Changes from previous version: ------------------------------- v3: Corrected the formatting in 'Fixes' tag. v2: Added 'Fixes' tag. Fixes: 1ac4329a1cff ("qed: Add configuration information to register dump and debug data") Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-08cxgb4: fix all-mask IP address comparisonRahul Lakkireddy
Convert all-mask IP address to Big Endian, instead, for comparison. Fixes: f286dd8eaad5 ("cxgb4: use correct type for all-mask IP address comparison") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-08net: atlantic: fix ip dst and ipv6 address filtersDmitry Bogdanov
This patch fixes ip dst and ipv6 address filters. There were 2 mistakes in the code, which led to the issue: * invalid register was used for ipv4 dst address; * incorrect write order of dwords for ipv6 addresses. Fixes: 23e7a718a49b ("net: aquantia: add rx-flow filter definitions") Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-07ionic: centralize queue reset codeShannon Nelson
The queue reset pattern is used in a couple different places, only slightly different from each other, and could cause issues if one gets changed and the other didn't. This puts them together so that only one version is needed, yet each can have slighty different effects by passing in a pointer to a work function to do whatever configuration twiddling is needed in the middle of the reset. This specifically addresses issues seen where under loops of changing ring size or queue count parameters we could occasionally bump into the netdev watchdog. v2: added more commit message commentary Fixes: 4d03e00a2140 ("ionic: Add initial ethtool support") Signed-off-by: Shannon Nelson <snelson@pensando.io> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-07net: qed: fix buffer overflow on ethtool -dAlexander Lobakin
When generating debug dump, driver firstly collects all data in binary form, and then performs per-feature formatting to human-readable if it is supported. For ethtool -d, this is roughly incorrect for two reasons. First of all, drivers should always provide only original raw dumps to Ethtool without any changes. The second, and more critical, is that Ethtool's output buffer size is strictly determined by ethtool_ops::get_regs_len(), and all data *must* fit in it. The current version of driver always returns the size of raw data, but the size of the formatted buffer exceeds it in most cases. This leads to out-of-bound writes and memory corruption. Address both issues by adding an option to return original, non-formatted debug data, and using it for Ethtool case. v2: - Expand commit message to make it more clear; - No functional changes. Fixes: c965db444629 ("qed: Add support for debug data collection") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>