| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds c45 registers direct access support in Microchip's
LAN865x internal PHY.
OPEN Alliance 10BASE-T1x compliance MAC-PHYs will have both C22 and C45
registers space. If the PHY is discovered via C22 bus protocol it assumes
it uses C22 protocol and always uses C22 registers indirect access to
access C45 registers. This is because, we don't have a clean separation
between C22/C45 register space and C22/C45 MDIO bus protocols. Resulting,
PHY C45 registers direct access can't be used which can save multiple SPI
bus access. To support this feature, set .read_mmd/.write_mmd in the PHY
driver to call .read_c45/.write_c45 in the OPEN Alliance framework
drivers/net/ethernet/oa_tc6.c
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Link: https://patch.msgid.link/20240909082514.262942-8-Parthiban.Veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the Microchip LAN865x Rev.B0 10BASE-T1S Internal PHYs
(LAN8650/1). The LAN865x combines a Media Access Controller (MAC) and an
internal 10BASE-T1S Ethernet PHY to access 10BASE‑T1S networks. As
LAN867X and LAN865X are using the same function for the read_status,
rename the function as lan86xx_read_status.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
By default, except Reset Complete interrupt in the Interrupt Mask 2
Register all other interrupts are disabled/masked. As Reset Complete
status is already handled, it doesn't make sense to disable it.
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Tested-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As per the datasheet DS-LAN8670-1-2-60001573C.pdf, the Reset Complete
status bit in the STS2 register has to be checked before proceeding to
the initial configuration. Reading STS2 register will also clear the
Reset Complete interrupt which is non-maskable.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Tested-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As per AN1699, the initial configuration in the driver applies to LAN867x
Rev.B1 hardware revision. 0x0007C160 (Rev.A0) and 0x0007C161 (Rev.B0)
never released to production and hence they don't need to be supported.
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Replace read-modify-write code in the lan867x_config_init function to
avoid handling data type mismatch and to simplify the code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove LAN867X from the driver description as this driver is common for
all the Microchip 10BASE-T1S PHYs.
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch adds support for the Microchip LAN867x 10BASE-T1S family
(LAN8670/1/2). The driver supports P2MP with PLCA.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
